Management VLan in Dell Powerconnect 6224

Similar Questions

• How to access the management of VLANs with a different virtual LAN (Dell powerconnect 6224)

  Hello

  DELL powerconnect 6224 reference.

  I want to access the management of a different VIRTUAL LAN VLAN.

  The management of VLANS is 100 of VLAN. not the routing

  My computer is vlan 60 (192.168.60.10) and I want to connect via ssh or http (192.168.100.1) to manage my switch.

  Thank you for your help on the command line

  The management of VLANS on the 6224 is not routable. So, you will not be able to access VLAN 100 from any other VLAN. However, you can manage the switch from other VLAN IP addresses. So if VLAN 60 has an IP of 192.168.60.1 you can http and ssh to it. And if the VLAN routing is enabled you have access to 192.168.60.1 on the other VLAN.

  See you soon

• I need manage the bandwidth used, PowerConnect 6224 traffic collision and packet traffic.

  I need manage the bandwidth used, PowerConnect 6224 traffic collision and packet traffic. I downloaded the MIB from the Dell support site and I saw thar there are about 105 MIB in the downloaded file. My question is: in what Mib, I can find the OID which allow me to monitor the above?

  Thanks in advance

  Rogerio

  Unfortunately, there is not a complete list of the different OID in different MIB. In order to find this info to simply browse through the different MIB seeking the OID, you need. We did some looking through the MIB and found these OIDs that can help you. Another thing to keep in mind is that the MIB downloaded are in general of a group of switches. So there are situations where a /OID MIB listed will work for a certain model of switch with certain level of firmware.

  RMON-MIB

  

  FastPath-cos-qos-mib

  

  Another method, some people have had success, done using a SNMP walk.

  http://www.snmpsoft.com/freetools/snmpwalk.html

  I hope this information helps. The method of importation for these MIBs can change based on the management/tracking software that you use.

  Thank you

• Transit VLAN on the PowerConnect 6224

  I need help to sort out a problem with routing on a 6224 we have configured to act as a vlan transit for one of our branches.  The general idea is 8.143 is the vlan of transit, of 8.144 is our PC LAN 8.145 will be our VOIP lan.

  We have installed this switch with our WAN provided last week, but had to get out. Traffic seemed to happen to the WAN providers to our transit interface VLAN (172.22.143.254) wasn't going anywhere.  It's symptoms

  (1) we could ping from 172.22.144.x to 172.22.145.x and 172.22.143.x

  (2) we could ping from 172.22.145.x to 172.22.143.x and 172.22.144.x

  (3) we could ping from 172.22.143.x to 172.22.144.x and 172.22.145.x

  (4) if I was plugged into the 6224 on with an address 143.x I could ping our remote control does site at 172.22.8.x no problem but not 144.x or 145.x

  (5) 172.22.8.x, I couldn't ping 144.x or 145.x or 143.1 (I could ping 143.254 which is EXTENDED to suppliers to our switch network interface)

  Here's the running to the switch configuration.  Any suggestions would be greatly appreciated:

  Console > activate

  Console execution #show

  ! Current configuration:

  ! Description of the system "PowerConnect 6224, 3.3.6.4, VxWorks 6.5.

  ! 3.3.6.4 system software version

  ! Passage mode is configured as disabled

  !

  Configure

  database of VLAN

  VLAN 143-145

  VLAN routing 143 1

  VLAN routing 144 2

  VLAN routing 145 3

  subnet of VLAN association 172.22.143.0 255.255.255.0 143

  subnet of VLAN association 172.22.144.0 255.255.255.0 144

  subnet of VLAN association 172.22.145.0 255.255.255.0 145

  output

  battery

  1 1 member

  output

  DHCP IP address

  IP routing

  IP route 0.0.0.0 0.0.0.0 172.22.143.254

  interface vlan 143

  Name the "Transit".

  routing ip address 172.22.143.1 255.255.255.0

  output

  interface vlan 144

  name "TWLAN".

  routing ip address 172.22.144.1 255.255.255.0

  output

  interface vlan 145

  the name "VOIP" routing

  IP 172.22.145.1 255.255.255.0

  output

  level of 746f7a78621059d80fdc538acc40cbf2 user name 'admin' password encrypted 15

  !

  interface ethernet 1/g1

  switchport mode general

  VLAN allowed switchport General add 143

  output

  !

  interface ethernet 1/g2

  switchport mode general

  VLAN allowed switchport General add 143

  output

  !

  interface ethernet 1/g3

  switchport mode general

  VLAN allowed switchport General add 144

  output

  !

  interface ethernet 1/g4

  switchport mode general

  VLAN allowed switchport General add 144

  output

  !

  interface ethernet 1/g5

  switchport mode general

  VLAN allowed switchport General add 145

  output

  !

  interface ethernet 1/g6 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g7 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/8 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g9 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g10

  switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g11 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g12 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g13 switchport mode General General switchport vlan allowed output adds 145! General mode of interface ethernet 1/g14 switchport

  switchport general allowed vlan add exit 145! interface ethernet 1/g15 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g16 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g17 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g18 switchport mode General switchport General allowed vlan add 145

  output! interface ethernet 1/g19 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g20 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g21 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g22 switchport mode General switchport General allowed vlan add exit 145

  ! interface ethernet 1/g23 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g24 switchport mode General switchport General allowed vlan add to exit 145

  Console #.

  It seems that port 1 must be in the VLAN 143, not general mode access mode. You already have a static route in place on the PowerConnect switch which directs traffic to the next break in the network. But it may be necessary for a place on the Cisco that allows to direct traffic to the PowerConnect switch.

  Here is a good post to look through also.

  http://en.community.Dell.com/support-forums/network-switches/f/866/t/19506015.aspx

• How Reboot/restart Dell Powerconnect 6224

  Hello

  My company has 2 powerconnect 6224, 1 is the master and 1 slave, do I know how could restart/reboot my switch in the GUI?

  Can I use the cli to restart/reboot command and what is the command line.

  Thank you

  Using the CLI to recharge the battery, you must use the # reload command. You can add the number of the switch in the command reload members of chimneys. charge # 1, # reload 2.

  You can also use the command console (config-battery) #initiate failover. This command forces a warm restart of the battery. The unit of backup succeeds the new management unit without clear status of material on the stack members. The original management unit restarts.

  In the graphical user interface, you can reboot the switch with entering the system > general > reset. You can also start a recovery using System > stacking > NSF summary. Initiate failover will begin a warm reboot of the switch.

• Slave keeps restarting after unstacking-Dell PowerConnect 6224 switch

  Hello everyone;

  I have 2 switches (PowerConnect 6224) on the other. Because we are them stacked like we got new switches, we decided to remove the cables from the battery and use them as individual switches.

  So I tried to unstacking the first switches using CLI, but it does not, simply, nothing happens. So I took the cards accumulation off both switches and removed the stacking cables.

  Switch works fine, but the slave is restarted.

  I correct the following:

  Startup options, tried to reset, restore the production parameters, format... They look successful the config looks like this is done and once the switch starts it asks me if I want to run the Setup Wizard, but it will just freeze and restart.

  is there a way to fix it? or the switch is dead?

  All ideas are welcome

  Thank you

  I would like to download the latest firmware.

  www.Dell.com/.../drivers

  Disconnect all other devices from the switch and follow the instructions of XMODEM that are included in the download to Flash the firmware.

• Proxy-arp or local proxy arp? Reference Dell Powerconnect 6224

  We need allow some customers to resolve the mac address of a server that is located in a different range of addresses, VLAN and IP.

  I thought that the addition of the ip proxy-arp interface command vlan should do the job, but this command seems to be activated by default according to the reference guide, after that I tried to add the command he always show up on a running show. Which confirmed my thoughts. While I was looking for the solution that I saw another command that does not appear in the cli reference guide: local-proxy-arp ip. But since I'm not sure of what will make this command I am careful to hit just the command on the interface VLAN.

  How others send their arp on powerconnect 6224 requests?

  After reading my own source again, I realized that the thing that I want is not possible. It goes beyond the need to divide the network into segments. If all the query arp is transferred to other networks, there is a benefit less: you want to limit the broadcast domain.

  Static ARP is the thing I'm going to need to be implemented to solve this problem.

  Thanks for the clarification anyway.

• VLAN between 2 powerconnect 6224 using XFP modules

  Dear friends,

  I have 2 switches powerconnect 6224 interconnected using optical fiber and XFP ports on the rear panel of the switch.

  There is no configuration of the battery between them.

  The distance between the two switches is 500 metres and they both work correctly when you use the vlan by default (use of the LAN)

  I created a virtual LAN using 2 ports on a firewall and I created the same vlan on the second firewall, but I can't see a VLAN traffic goes to the other.

  Also, I tried to configure the port as trunk but same result.

  The vlan works very well in a single switch, but traffic is not able to flow to the second switch.

  You have an idea why does not?

  Maybe is not posible to have VLANs using xfp connections...

  Any idea would be greatly popular.

  Thanks in advance!

  Rear ports are labeled xg1, 2, 3, 4. So, if the connection is made using the xg1 on a single switch for xg1 on the other switch. Then you enter interface 1/xg1 and make configuration changes.

• Dell Powerconnect 6224 Default VLAN VLAN reference and management

  Hello

  two questions-

  1. what exactly he wants to tell the VLAN by default is not routable or VLAN 1 is not routable? I can connect to my 6224 a different subnet and its got nothing configured except default values and an IP address to this VLAN

  2. I have a stack of 2 x 6224 s, 95% completed and all on the default VLAN 1. I won't use VLAN 1. So I create a VLAN 10 and "range Ethernet all interface ' followed ' switchport access vlan 10"»

  Now I can not connect on the network. That's happened? How can I move everything cleanly on VLAN 10 and it is possible via the network or must it be done with a cable from the console?

  Thank you

  Hello, by default, the management interface is in VLAN 1, if you want to she be changed to VLAN 10 please use the command 'ip address vlan 10' in the Setup mode and check the status of management interface using the command 'show ip interface '.

• Reference Dell Powerconnect 6224 DVLAN-mining (Q in Q)

  I have two sites, one is our data center and the other is our office.

  I want to be able to access the data center to the office network, I need access for 2 VLANs, the ISP has already installed it is fine for this and now there's only the part configuration

  At the office, there is a PC5548 and data center, there is one PC6224.

  Office on the incoming port configuration is:

  tengigabitethernet1/0/1 interface
  switchport mode trunk

  The port for outgoing data center conf is:

  interface ethernet 1/g22
  Description "TELEV6RK".
  switchport mode general
  VLAN allowed switchport General add 3000
  dvlan-tunnel mode

  This does not work, how do I configure ports, do I have to configure all ports or only 1 port IDE oucederomsurlesecondport 5548 and 1 on 6224?

  I got an answer from Dell technical support, on how to do it:

  1. If the marking through ISP is different from DOT1Q then you must change it on the two switches using the command global dvlan-tunnel ethertype and options there are (dot1q, vman or custom)

  2 port 1 and 2 must be port trunk who accept only the 3000 VLAN. Here are the ports that are connected to the ISP.

  3 ports 3 and 4 should be dvlan-tunnel mode configured on them and configured as switchport access VIRTUAL 3000 LAN mode. These are ports that are connected to switches that are for production at both sites.

  4 ports 5 and 6 on other switches must be configured as trunk with tagged VLANs you want to transfer through ISP in VLAN 3000. These are the ports located on the switch of production.

  The topology is here: www.upload.ee/.../Topology-change.png

  I hope that now everyone will have its operation :) Thanks for the help.

• Reference Dell Powerconnect 6224

  Hello, we need help to choose the right device of balancing of affordable to work with dell switches load 6224 we have two switches with two dedicated company comcast internet (2 5 static IP gateways each) low 100meg 20up we have a load of 400 traffic +, we see that there is Load Balancer ADC like Barracuda, Kemp etc. have no need for security with a cost of one year to the next we have just need a good load balancer with some security as ddos to effectively distribute traffic while ensuring high performance for games & voice servers hosting we have a large community make world wide everything is free... What would you use? Thank you

  Sonicwall Dell devices provide failover and load balancing. Not sure that they meet all of your requirements, but interesting look in.

  http://www.SonicWALL.com/us/en/products/failover-failback.html

  Your post on Spiceworks had some excellent feedback from the community.

  See you soon

• VLANs for PowerConnect 6224

  Hello

  I bought Dell PowerConnect 6224 & I'm newbie for VLAN management. To put it simply, how can I create two VLANs (vlan 10 - 192.168.10.x/24 & vlan 20 - 192.168.20.x/24) that can communicate with each other without defining the point of gateway for the network servers and workstations to the ip address of vlan?

  Thank you.

  Here is a link to the manuals available for the Dell PowerConnect 62xx:

  support.Dell.com/.../index.htm

  Creation of VLANS

  Console > activate

  Console # config

  Console (config) # vlan database

  VLAN console(config-VLAN) # 10

  output console(config-VLAN) #.

  Console (config) # interface vlan 10

  # Ip address 255.255.255.0 192.168.10.x console

  Console # name Marketing

  Console # end

  console # show vlan

  Creating Ports for PC to connect as a ignorant guest VLAN.

  Console > activate

  Console # config

  Console (config) # interface ethernet 1/e1

  Console # switchport mode access

  Console # switchport access vlan 10

  Console # end

  Enable routing

  To globally enable IPv4 routing on the router, use the command "ip Routing".

  in Global Configuration mode.

  Console (config) #ip Routing

  You will need to create the VLAN as described above.  Then, set the access mode for a port VLAN particular then set the PC with an IP address in the range of the subnet for the VLAN and the gateway as the IP address of the address that you provided for the VLAN on the port.

  Then once the routing is enabled in the world it should allow communication between VLANs and configured different subnets.

  Hope this helps,

• PowerConnect 6224: Dell SFP + port supports combine Dell SFP?

  I have a Dell Powerconnect 6224 switch and I installed a Dual Port SFP + Module of adaptation for PowerConnect
  6200 series at bay2 at the rear of the switch. I inserted a transceiver, SFP 1000BASE-LX, wavelength 1310nm 10km Reach in the SFP slot + and the other end is connected to a connector SFP 1gbe. I don't have any link. My question is if Dell SFP ports + supports SFP transceivers or it only supports SFP transceivers +?

  I checked the ports to help an SFP + SFP +, 10GbE, copper Direct Attach cable Twinaxial, and link LEDs are lighting up.

  I believe that the SFP ports + back work with SFP transceivers. Ports before combo will work with SFP transceivers. Another thing to look at is the cable being used. Don't forget that there are specifications that are compatible with transceivers FPS are you wanting to use. A SFP + SFP connection would require that the SFP transceiver + supports a connection of 1 GB.

  Hope this info helps.

• VLAN routing when you use a dell computer 6224

  Hello

  I have a dell switch 6224 with 2 VLANS.

  Management-192.168.1.111/24 Ports 1/g1-1 / g12

  Vlan150-192.168.150.111/24 Ports 1/g13-1 / g24

  I have two ports on the router with the ip address to communicate with the switch (192.168.1.2 and 192.168.150.2). Vlan1 works very well without any problems. I can ping from 192.168.150.2 to 192.168.150.111. I set up the laptop with the ip 192.168.150.113 and plugged in the Vlan150 on port 1/g19. I can not ping to 192.168.150.113 192.168.150.2. The traffic is not going through the Vlan150 in the switch.

  What Miss me? This is my first time setting up a VLAN on these switches. Help, please.

  Config

  console #show running-config

  ! Current configuration:

  ! Description of the system "PowerConnect 6224, 3.3.8.2, VxWorks 6.5.

  ! 3.3.8.2 system software version

  ! Passage mode is configured as disabled

  !

  Configure

  database of VLAN

  VLAN 150

  VLAN 150 1 routing

  subnet of VLAN association 192.168.150.0 255.255.255.0 150

  output

  battery

  1 1 member

  output

  192.168.1.111 IP address 255.255.255.0

  by default-gateway IP 192.168.1.2

  IP routing

  interface vlan 150

  name "VLAN150".

  Routing

  IP 192.168.150.111 255.255.255.0

  output

  level of 00436d6ae2ed27bbe87fa24b73b5a249 user name 'admin' password encrypted 15

  line of AAA authentication login "defaultList".

  the AAA authentication enable line 'enableList '.

  line console

  00436d6ae2ed27bbe87fa24b73b5a249 encrypted password

  output

  line telnet

  connection of authentication defaultList

  00436d6ae2ed27bbe87fa24b73b5a249 encrypted password

  output

  ssh line

  connection of authentication defaultList

  00436d6ae2ed27bbe87fa24b73b5a249 encrypted password

  output

  !

  interface ethernet 1/g1

  switchport mode general

  output

  !

  interface ethernet 1/g2

  switchport mode general

  output

  !

  interface ethernet 1/g3

  switchport mode general

  output

  !

  interface ethernet 1/g4

  switchport mode general

  output

  !

  interface ethernet 1/g5

  switchport mode general

  output

  !

  interface ethernet 1/g6

  switchport mode general

  output

  !

  interface ethernet 1/g7

  switchport mode general

  output

  !

  interface ethernet 1/g8

  switchport mode general

  output

  !

  interface ethernet 1/g9

  switchport mode general

  output

  !

  interface ethernet 1/g10

  switchport mode general

  output

  !

  interface ethernet 1/g11

  switchport mode general

  output

  !

  interface ethernet 1/g12

  switchport mode general

  output

  !

  interface ethernet 1/g13

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g14

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g15

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g16

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g17

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g18

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g19

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g20

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g21

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g22

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g23

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  !

  interface ethernet 1/g24

  switchport mode general

  VLAN allowed switchport General add 150

  switchport vlan allowed General remove 1

  output

  activate 00436d6ae2ed27bbe87fa24b73b5a249 encrypted password

  output

  Hello

  The laptop is probably sending unmarked packages and so you need to change the PVID on the interface so that the unmarked packages are assigned to 150 of VLAN.

  switchport General pvid 150

  FTP://FTP.Dell.com/manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/PowerConnect-6248_Reference%20Guide_en-us.PDF page 600

• Dell PowerConnect 2724 managed Mode reference works do not?

  I recently acquired a dell powerconnect 2724 from a friend, and I can't find the web interface. I tried the default IP addresses and I looked on an application to register all IP addresses on the network, and the thing only dell was my PowerEdge R710. I made sure it was in managed mode and I tried to reset it. Suggestions?

  From the factory, the PowerConnect 2708/2716/2724 units have a default IP 192.168.2.1 255.255.255.0 assigned. This IP address is assigned to the management VLAN 1. Be sure not to delete the VLAN 1 management or you will not be able to manage the switch. If the switch is unmanageable, and then change the transition to unmanaged and return to managed mode to reset the default settings.

  Remember that the client attempts to access the switch is also in the 192.168.2.0 subnet. If the customer is not in the same subnet, it will be able to access the 192.168.2.1 IP address. Check and make sure that nothing else on the network also has 192.168.2.1 assigned.

  Keep us informed.