Manual 910

Similar Questions

• HP OfficeJet 8500 has more 910 g give up connection every now and then

  I explored the forums for 8500 more connectivity issues and did the following, but the problem persists:

  I am using the Wi - Fi connection (force 4), web update services and software packages, can use eprint, but printer loses connection (even with eprint servers). I have it set to fax so phone line is connected and noticed that when a call arrives (or goes), it restores the network connection. It seems that he loses the connection when it starts in mode 'sleep'. Is there a way to disable, and then do a test?

  I noticed that first print wirelessly from a laptop computer crashes and comes back with an error (sometimes work after a long time), but the second try and then work (it seems that the first test is trying to put the printer back to the mode 'sleep'!)

  I have the static IP assigned (in both the printer and the router) and static DNS primary.

  I have IP v4 ONLY on the printer.

  What can be done? Help, please. The printer is only a few days old!

  I finally realized that you can go to the 'Préférences' menu on the touch screen and disable the "power saving Mode" - this apperently solved the "problem of loss of connection" (with static IP/DNS and IP v4 only)- but the screen was continually WE (and quite brilliant - more than a lamp at night!). I also found that there is an option under "Tools" screen saver But the screensaver works just the video "promo" continuously without interruption and with the same brightness on the screen. Is it possible to say 'black' after 10 minutes?

  Perhaps HP should provide a screen saver that turns off the display after a period of inactivity.

  APPARENTLY, THE LOSS OF CONNECTION BUG IS DUE TO "ENTERGY SAVE MODE" WHERE THE WIRELESS LAN CANNOT DETECT TRAFFIC TO WAKE UP THE PRINTER. THIS SHOULD ALSO BE FIXED IN THE NEXT FIRMWARE.

  To SUMMARIZE: In order to avoid the 'loss of connection"(for wireless) perform the following steps:

  1 assign a static primary DNS and static IP address (through EWS doing via a browser is easier - see below on access EWS).

  2. optional but recommended: connect the printer wireless MAC address to the same static IP address in the configuration of the router (router consult manual or vendor on how to do this).

  3. via the integrated Web server accessed through a browser of computer - under 'Network' settings, select 'IP v4 ONLY' (EWS is accessed through a browser on the same wireless LAN by typing http://192.168.1.xxx - where xxx is the IP address assigned statically - you can find it via touching the wireless icon on the screen in the printer)

  4. go in the 'preferences' and disable the "power saving Mode" (in the touch screen of the printer interface)

  5. optional but highly recommended: turn on the "screen saver" in the "Tools" menu (in the touch screen of the printer interface)

  6 see if it the problem slves (mine is running fine since then)

  These steps are for HP Office Jet 8500 has more 910 g printer. I hope it helps someone here!

• HP officejet pro 8500 910 a guard cleaning print head

  HP officejet pro 8500 910 a constantly clean the print head after replacing cartridges inkt (original)

  This happens after each power off/on. I can't stop the process by opening the doors, etc. Could not understand what did the trick.

  The new cartridges are already half empty.

  I did all the configurations, calibration. All the test pages are superb and I still suffer from the issue.

  In this forum, someone (Dutch) had exactly the same problem.

  I hope that someone from HP is able give me some tips.

  Hello there @qtoigoo ,

  I understand that you are facing a problem with your Officejet 8500 continuously clean the print heads. Normally, this occurs if the print heads are going downhill. My best advice to you would be to try clean the contacts on the print heads manually and reset of the printer. Who can help.

  Here is a guide with the relevant instructions: print head issues

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions: click here.

   

  I hope that my post was information!
  

   

  Have a wonderful day
  

• from readers require manual connect

  We organize several vaults file AFP/SMB interview about 30 workstations, which now require manually hit 'connect' on the window of connection for each server. We checked the username/password to inhabit the keychain of the local machine (that we don't store the trousseau on the cloud), and all drives are listed in user "Login Items" list. This issue was not a problem on El Capitan, or earlier.

  Thanks in advance

  This question was for the first time in the beta versions of Sierra. It was not fixed at the time of the release. Maybe it will be fixed in an update of the Sierra...

• How to manually lock iwatch with last software update

  The last update, I am unable to manually lock my iwatch

  Hello

  To manually lock Apple Watch under watch OS 3:

  • When you display the time on your watch, drag upward on the screen to open the control center > press the button with a lock icon to lock your watch (you may need to scroll to see it).

• Thunderbolt manual bridge IP no longer works with Sierra

  I use a Thunderbolt bridge with manual IP connection to connect 3 mac to my main MacPro, since the update of Sierra I can't connect one of the mac via the manual / plus static IP.

  Please HELP, am I missing something? It has worked before and now it no longer work.

  Joe

  Anyone?

  My work is stationary, and my staff is looking at me.

  Help, please!

  I also note that since the Sierra update whenever I connect to the server via the LAN cable or stroke, it appears this box, -that use only to appear only once (when I put in place) and hten again, unless I have re - install the operating system.

  Perhapse it is a new way to set up an IP Maunaul or I've never done right. Help, please.

  I pay my staff to do nothing right now.

• Setup Airport Express: how to manually set the IP address and DNS?

  I just bought an Airport Express for the wifi in the ethernet cable that I have in my dorm room.

  To connect to the internet via the ethernet cable, I need to enter a number IP, DNS, gateway and mask provided by the dorm (as I did on my Macbook).

  The problem is that I don't see where I can do for the Airport Express. After I plugged the cable into it, it keeps wanting to configuration alone, which does not work (he's trying to "join the network" forever, without success).

  How can I configure IP, DNS etc. manually?

  Thank you much for the help

  Hello!

  I read the post and found article suggested for her: OS X El Capitan: connect to the Internet or a network using Ethernet

  Thank you!

• Impossible to manually configure the wireless settings.

  I have an Apple Time Capsule of 7.7.7 version and no matter what I do I can't seem to accept my manual settings wireless.  My building a House requires several APs to provide adequate coverage, and time Capsule keeps selecting wireless channels that are in conflict with other access points in the House.  Does anyone know of a work around that will allow me to force the desired channels? I use a Windows PC 10 with Airport Utility for Windows version 5.6.1 configure time Capsule. Here are the steps I followed:

  -Select the "Time Capsule" on the left side

  -Click on the "Manual Configuration" button at the bottom

  -Select the tab "wireless".

  -Radio mode - menu drop down select "802. 11A / n - 802. "11b / g ' (very intentional)

  -Radio channel selection - I select in the drop-down "manual."

  -Select 'change... '. "and choose"36"for the 5 GHz channel and '1' for channel 2.4 GHz, then 'Ok '.

  -Select "Update."

  After restarting the device, I check the settings and I find...

  -Radio mode is back 'automatic '.

  -Selection of the radio channel is 'Automatic' and channels do not necessarily match what I selected initially.

  Someone at - it advice?

  The main problem is that the version of the AirPort for Windows utility is not designed to work with 802.11ac airport base stations. Unfortunately, Apple has not updated this utility since Windows 7.

  The other problem is that Apple has "dumb - which crashed" AirPort Utility for Macs and the iOS devices with version 6.x. One of the things that he removed has the possibility to define patterns of radio and channels that "stick" to the 802.11ac base stations.

• need a manual for series 2

  Where can I find a series 2 manual. Can't see series1

  Hello

  Apple Watch user guide is available here:

  https://help.Apple.com/watch/

  It includes reference to the features of the series 2, if applicable.

• I can not pair my Apple Watch with my iphone 6 s so true the automatic procedure freezes the app on my iphone. If manually matching the 6 digit code will appear on the Apple Watch. I have the current ios 10.0.1

  I can not pair my Apple Watch with my iphone 6 s so true the automatic procedure freezes the app on my iphone. If manually matching the 6 digit code will appear on the Apple Watch. I have the current ios 10.0.1

  does anyone have a solution to this?

  Hello

  The following steps can help (try again after each):

  • On your iPhone, in the application of the watch, go to: Watch My > general > use > software update - remove any file update, if one is displayed.
  • Delete all profiles beta (on your iPhone and/or the watch), then restart both devices (this applies only if you have already participated in a program of Apple Beta software).
  • Restart your iPhone and your watch:
    • Close open applications on your iPhone:
      • Double-click the Home button, and then drag upward on each Preview app to close.
    • Close the two devices together, and then restart your iPhone first.
      • Restart your iPhone, iPad or iPod touch - Apple Support
      • Restart your Apple Watch - Apple Support

• How to add manual iOS app health data?

  I use Apple Watch series 1 with Watch OS 3.

  Very useful for me has been adding data to guide health app. Now with OS3 shows, I couldn't find these options.

  Can someone help me in this case?

  Thank you, Michael

  Hi Michael

  To manually add data in the application of health:

  • On your iPhone, open the application of health.
  • Click on the data the health tab.
    • If you are not initially on the main screen of healthcare data, type on the "< health data ' link (top-right) to get back to it.
  • Select the category of data that you want to add:
    • Activity, Mindfulness, Nutrition, sleep, measurements of the body, health, reproductive health, results, vital records.
  • On the next screen, tap the metric you want to add:
    • Parameters that already contain data for the current week are displayed in the box format, with current totals.
    • Others are listed below in the list format, under "No. saved data.
    • Whether in box form or list form, tap to select the metric.
    • For example: If you chose healthcare, you can then select the blood sugar.
  • On the next screen, press the "+" (top right), then add your data and press Add (top-right) when finished.

  More information:

  Use the app on your iPhone or iPod touch - Apple Support health

• Manual lap (or segment) the pace and distance

  Is there a way (or will there be a way) to see tour distance and pace on the lookout for series 2? I want to set manual towers (or "segments") on trips and see my stats in real time, and not only in the application phone later. I've used this feature on my garmin all the time and it is very useful when the PACE work or attend training sessions. I also use strava, but I don't see either this function in their application.

  Hello

  To mark a segment (for example a tower) year running, double-tap the screen, then wait the segment summary appears in the display.

  More information:

  Work with your Apple Watch - Apple Support

• Health after app updated iOS at level 10, can't enter manually blood sugar longer?

  After the upgrade to iOS 10 can I enter is no longer blood sugar? I followed my blood sugar every day for years. It seems now there is no way to do it manually. WHA' happened?

  Try these general steps. They could help.

  1 reset your iPhone by pressing and holding the sleep/wake and home buttons.

  2 disconnect you from your iCloud account and reconnect again.

• background app refresh all turns on itself.  It happens again and again even after manually more offshore.

  found a weird problem, background app refresh all turns on itself.  even after manually most offshore, he just turn it all back on automatically.  told me that the hottest phone and I have to manually turn off most of them.  but after a while, it happens again.

  BTW, the top bar sometimes disappears as well.

  above 2 questions never happened to me before iOS 10. I'm on iphone5s

  any ideas to get it repaired?

• difficult to manually enter data into health

  with the last update apple has made it very difficult manually enter data into health app... I'm not talking about sugar in the blood or the weights every day entered manually as my personal info that does not normally change

  Launch the health application and then press update medical ID.

  For example, on your birthday, tap the box just to the right of the birth Date of edit.

  Use the app on your iPhone or iPod touch - Apple Support health