MARCH and fortigate

Similar Questions

• Site to Site with ASA and FortiGate

  I have setup a VPN site-to site between my ASA and FortiGate customers. The tunnel rises with success, but we can not pass traffic. When I do a packet capture on my ASA, I see traffic on the port of entry as usual, but on the output port, the source address gets NAT had I checked all statements of NAT, and there is a statement NAT exempted from the entry port to the port of exit and in the VPN configuration.

  Then your oder of NAT statements in probably wrong. The dynamic NAT for outgoing traffic must be at the end (I put them always in article 3), while the Exemption must be at the beginning of Section 1.

• (Between Cisco and Fortigate) IPsec tunnel question

  Hi all

  Im trying to install an IPsec site-to-site between 2 different routers (Cisco 3750 and Fortigate 100a) (R1 & Fortigate100A)

  IPsec, the whole scenario works with the installation.

  But unfortunately the tunnel (between R1 & Fortigate100A) IPsec does not work.

  (Pls look at the attached jpg file)

  The message is received in routers are shown below:

  Cisco: R1:

  % CRYPTO-6-IKMP_MODE_FAILURE: fast mode processing failed with the peer to 192.168.43.75

  FortiGate 100A:

  IKE 0: none established HIS IKE for informational type of d18e1af773e658b9/192.168.43.195:500->192.168.43.75 Exchange 3 cookie d3695c6cea17475a, don't drop

  IKE 0:Cisco - P1:6899: authentication OK

  IKE 0: none established HIS IKE for informational type of d18e1af78ed17bf9/192.168.43.195:500->192.168.43.75 Exchange 3 cookie 414bd35ab92bc4ef, don't drop

  IKE 0:Cisco - P1:6899:Cisco - P2:14802: failure of negotiating quick mode due to the delay of new attempt IKE 0:Cisco - P1:6900: authentication OK

  I configured both routers as follows:

  Cisco:

  HostName:R1

  ISAKMP policy 1

  Hash: sha

  Authentication: pre-shared

  Encryption: AES128

  DH group: 2

  Life 86400

  ISAKMP Key: cisco1 address 192.168.43.75

  Crypto IPsec transform-set esp - aes and hmac-sha-esp RIGHT

  Access-list: 101 permit ip 10.0.0.0 0.0.0.255 10.10.10.0 0.0.0.255

  Map R1_to_Fortigate100A 10 IPsec-Isakmp crypto

  defined by peers: 192.168.43.75

  Mailing address 101

  The value transformset: RIGHT

  int fa # 0 / 0 Crypto map R1_to_Fortigate100A

  FortiGate:

  HostName: Fortigate100A

  Phase 1:

  Preshared key: cisco1

  The remote gateway ip address: 192.168.43.195

  mode: aggressive

  Accept any pair

  Proposal P1:

  AES 128 / SHA1

  AES 192 / SHA1

  AES192/SHA 256

  DH: 2

  Keylife: 86400

  Phase2:

  AES 128 / SHA1

  AES 192 / SHA1

  AES192/SHA 256

  Keylife:86400

  Quick mode selector:

  Source address: 10.10.10.0/24

  Destination address: 192.168.43.0/24

  I will be very very very grateful if you informed of my faults possible a solution

  Happy new year

  Ministry of education

  For some time I messed with a fortigate, but I would try first to change the remote address of the phase 2 to 10.0.0,0/24. If this is the statement "interesting traffic", it does not match what you have on the Cisco. After that, try to change the phase 1 Ike mode to something else than "aggressive."

  Sent by Cisco Support technique iPad App

• Tunnel GRE / IP Sec VPN firewall between the router Cisco and Fortigate

  Hello

  Can I do GRE Tunnel / VPN IP Sec between Cisco router and Fortigate Firewall?

  Thank you

  Hi zine,.

  As long as the Fortigate device support GRE over IPSEC, you will be able to create the tunnel between these 2 devices.

  Here is the config for the Cisco Site:

  https://supportforums.Cisco.com/document/16066/how-configure-GRE-over-IPSec-tunnel-routers

  Happy holidays!

  -Randy-

• I downloaded cs6 to evisoft in March, and all is well. My laptop no longer works and so I bought a new laptop. I tried to re download cs6 to evisoft, but they don't exist today. I have licensed authentic number which adobe has recognized a

  I downloaded cs6 to evisoft in March, and all is well. My laptop no longer works so I bought a new. I tried to download evisoft on my new laptop cs6 and find him no longer exist. The software is authentic with a genuine license number and it has worked well and updated normally. Because I can download it is more evisoft, could I download it directly from adobe using my current license number?

  CS6 - http://helpx.adobe.com/x-productkb/policy-pricing/cs6-product-downloads.html

  You can also download the demo version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  CS6: http://prodesigntools.com/adobe-cs6-direct-download-links.html

• How re - set my DST auto to change in March and April, no?

  Now that the DST starts in March rather than in April, I would like to reset the automatic DST for March. If this is possible, how?

  This forum is for comments on the operation of the forums themselves. It is not for technical questions. To find an answer to your question, click Windows in the top navigation bar and type your question in the box to find answers .

  Probably, you will be directed to this article:

  How to configure daylight saving time for Microsoft Windows operating systems

• CIsco ISE with HP and Fortigate

  Hello

  I configured the switches HP 5820 X and 5130 for authentication radius AAA with Cisco ISE 2.0.0.306.

  The switch receives the response from authorization successful; but unable to connect. What are the Advanced profile Radius authorization attributes in

  ISE?

  In addition, ISE supports Fotigate firewall?

  Oh and Yes ISE supports any device using the RADIUS in accordance with rfc, it is usually only a question about this that av-pairs to send to that specific device, there is not really standard for this.

• Forgot Cisco MARCH username and password

  Hello

  I have server Cisco MARCH and I forgot the password to access.

  However, I try to follow these instructions

  http://www.securitytut.com/mars-642-545/share-your-mars-experience
  

  I can not access MARCH.

  Someone has a solution to this problem and I wouldn't reinstall MARCH

  Unfortunately MARCH reimage is the only way if you have forgotten the password.

• How configure MARCH to interpreter windows event and sending email

  Someone knows how to set up a MARCH to interpret a newspaper determined in windows events? The server is already configured in the March and events are stored in MARCH, I want to say MARCH "when you see an event with the XXX text, please send email to [email protected]" / * /".

  Thank you

  Of course, create a rule to control of a key word in the offset. Once you have tested, add a notification action. The notification are not sent to the event, just a link to the incident.

• Cisco ASA and dynamic VPN L2L Fortigate configuration

  I met a problem recently with an ASA 5510 (7.0) and a bunch of Fortigate 50 (3.0 MR7). The ASA is the hub and Fortigates are rays with a dynamic public IP.

  I followed this document on the site Web of Cisco (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805733df.shtml) to set up my ASA and the parameters passed to my counterparts to set up their Fortigates.

  However, the ASA journal reveals that attemtps Fortigate connection always tried with DefaultRAGroup before falling back to DefaultL2LGroup and finally died. Experience with putting in place a dynamic VPN between Cisco and Fortigate someone? Which could not fail at each end? Here's a typical piece of error log ASA. The ASA is currently having a static VPN tunnel and a site-2-client VPN in two groups by default.

  6. January 10, 2011 20:58:45 | 713905: Group DefaultL2LGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:45 | 713201: Group = DefaultL2LGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:45 | 713905: Group DefaultL2LGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:45 | 713201: Group = DefaultL2LGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:41 | 713905: Group DefaultL2LGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:41 | 713201: Group = DefaultL2LGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  4. January 10, 2011 20:58:39 | 713903: Group = DefaultL2LGroup, IP = 116.230.243.205, ERROR, had decrypt packets, probably due to problems not match pre-shared key.  Abandonment
  5. January 10, 2011 20:58:39 | 713904: Group = DefaultL2LGroup, IP = 116.230.243.205, received the package of Mode main Oakley encrypted with invalid payloads, MessID = 0
  6. January 10, 2011 20:58:39 | 713905: Group = DefaultRAGroup, IP = 116.230.243.205, WARNING, had decrypt packets, probably due to problems not match pre-shared key.  User switching to the tunnel-group: DefaultL2LGroup
  5. January 10, 2011 20:58:39 | 713904: Group = DefaultRAGroup, IP = 116.230.243.205, received the package of Mode main Oakley encrypted with invalid payloads, MessID = 0
  4. January 10, 2011 20:58:33 | 713903: Group = DefaultRAGroup, IP = 116.230.243.205, error: cannot delete PeerTblEntry
  3. January 10, 2011 20:58:33 | 713902: Group = DefaultRAGroup, IP = 116.230.243.205, Removing peer to peer table has no, no match!
  6. January 10, 2011 20:58:33 | 713905: Group DefaultRAGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:33 | 713201: Group = DefaultRAGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:25 | 713905: Group DefaultRAGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:25 | 713201: Group = DefaultRAGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  6. January 10, 2011 20:58:21 | 713905: Group DefaultRAGroup, IP = 116.230.243.205, P1 = relay msg sent to the WSF MM
  5. January 10, 2011 20:58:21 | 713201: Group = DefaultRAGroup, IP = 116.230.243.205, in double Phase 1 detected package.  Retransmit the last packet.
  5. January 10, 2011 20:58:19 | 713904: IP = 116.230.243.205, encrypted packet received with any HIS correspondent, drop

  Yes, sounds about right. He will try to match with the DefaultRAGroup first, and when you know that it's a dynamic IPSec in LAN-to-LAN, it will be

  then back to the DefaultL2LGroup, because he doesn't know if the VPN Client or L2L again when he is contacted fist as they are connecting from dynamic IP peer.

  You must ensure that your L2L tunnel-group by default has been configured with the corresponding pre-shared key.

  Assuming that you have configured the dynamic map and assign to the card encryption.

  Here is an example of configuration where ASA has a static and peripheral ip address pair has dynamic IP:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

  Hope that helps.

• Help! My files sent for two whole months are missing! I have looked everywhere and looked through the forum topics, without success.

  At the beginning of a new month, Thunderbird normally creates a sent folder for the previous month, as in "Feel-Apr-2014." All my emails in the last two months are - missing files for March and April 2014. I looked through all my records, to see if they went to the wrong place. I also tried searching for individual emails by name, to see if they are elsewhere, but there is a gap of two months with no emails showing up during this time. I checked my master settings, to make sure that nothing is set to automatically delete. This is very serious. I'll have to stop using Thunderbird, I used for four years, if I can't solve this problem, because I can not afford to continue to lose huge chunks of important emails.

  Thank you. Your account appears to be IMAP, that is, all mail is handled on the server.
  
  Can connect you to your account via webmail and check if the mail is missing on the server?

  At the beginning of a new month, Thunderbird normally creates a sent folder for the previous month, as in "Feel-Apr-2014."

  Is it possible that this is done by the server?

  Of after troubleshooting - profile directory - Open Directory information

  Your profile folder opens in Windows Explorer. Under ImapMail, look for a folder with your domain name in the name of the folder, i.e. something like mail. [sitename] .com. What are records under?

  Maybe you can post a screenshot.

  http://support.Mozilla.org/en-us/KB/how-do-i-create-screenshot-my-problem

• Satellite Pro C50 - A - 1 K 9 - screen flickers power on and off

  Has anyone encountered a problem where the screen flickers power on and off? Mine will Dim to the point where you can't see whats happening and then back to normal.

  I tried a restore drivers, but the problem persisted. I did also check complete anti-virus (I realize that it was probably not the cause of the problem, but decided to be complete). I was thinking that it's purely a hardware problem, like when I use an external monitor connected through a HDMI cable I don't have this problem.

  I guess it must be a problem with the connection between the screen and the motherboard. Maybe a problem within the hinge where they cross connection.

  Anyone got any other suggestions until I sent it off for repair (only he got in March and I have a 2 year warranty, but who goes back to college soon and do not want to be without him).

  I have a Toshiba Satellite Pro C50 - A - 1 k 9.

  Thanks in advance.

  I agree with you, Fraser and think it could be hardware related issue but I don't in any way you can fix it alone. Your laptop must be controlled by the Toshiba service provider.

  Contact the nearest service provider for Toshiba in your country, explain the situation and ask for help.

• Difference between the G20 and G25 models

  Hi people!

  I searched your laptop and I was amazed by the Qosmio.
  When I was going to order it, I noticed that there are many models of the G20 with different specifications. Also, I found G25 on internet research and found no difference between the G25 and G20 except receiver TV G25 is NTSC and G20 was released on March and G25 was in June. Instead, they have the same specifications for the hard drive.

  I live in the Portugal and the model Qosmio I can find that this is the G20-118. I was looking for the model that has 2 x 100 GB SATA HD, but cannot not thought about it.

  Internet research I found Qosmio G20-111 which has 2 x 100 GB SATA HD, but on the web page mentioned that it was a Pentium III processor (ridiculous, isn't?). I was looking for more reliable information.

  Already searched for toshiba pages and found no specifications for all models I found 490LS on the research on the web as the G20 - 102, 105, 106, 108, 109, 111, 118, 123,...

  Can someone help me with this? Are there any reliable web page where I can see the differences between the models? is there a .pdf or anyone who can please give me some advice?

  Money is not a problem at this time to acquire the laptop, I'm looking for only the laptop performance more!

  Best regards
  João Pereira

  Hello

  It of very difficult to say what camera is best, because there are many models with different parts.
  However, I found page with description of the G20 and G25.
  Take a look at this link.

  http://www.releasereview.com/Toshiba-Qosmio-G20-105-108-114.aspx?d=0101000580926052005

  Good bye

• Satellite series A turn off for the game Command and Conquer 3

  Hi all

  This happened to me twice. While I was relax play skirmish Command and Conquer 3, computer laptop turns off suddenly. I was running an external power supply and the battery was full. What is even more strange, it was impossible to next turn to the until I removed the battery and plugged in.

  I bought this game around March and was able to beat the 3 campaigns without these attractions.
  I suspect that this may be caused by overheating, because after the laptop is pretty hot. What do you think? I bought it in January.

  In my Office I occasionally removed the fan and radiator vacuum, there accumulates a lot of dust sometimes. It is not easy in the case of laptops. Any suggestions? See you soon.

  Hello

  You should do a bios update, because I had a similar problem with my A100 and after updating the bios to the version the most recent (5.60) I had no problem more. Maybe it helps.
  The other thing is, if you have a ventilation system which is clobbed with dust, then you should take a container with compressed air (you can get it in every electronic market/store) and gently lead some air to breath through the ventilation holes. (like 2 seconds. Wait, then wait 2 seconds and so on; just make short sounds :))
  Then, ventilation must be clear.
  Otherwise bring your machine to a service partner for a checkup of material because some loose cables inside the machine could probably be a reason that the machine feeds not correctly on...

  Welcome them

• problems of gps and wifi iPhone 6 9.2

  My iphone 6 does not connect to the wifi unless it is less than 5 feet from the router and the GPS can't find my spot.  This has happened since Apple updated the software around the release of the 6s.

  None of the versions subsequent correction of the problem, nor has any troubleshooting discussed in online forums, proposed by technicians apple or carried out by technicians from apple to the store.

  My phone is a few months after its warranty (how convenient for apple) and they would not replace it without paying me $ 280 to do.

  I am a few months since my full upgrade with Verizon, but the lack of GPS and wifi not connecting not caused much frustration and data usage, which was costing money because it does not connect to wifi when the fact of other devices in my apartment.

  This is one of the worst customer experiences I've had with apple.  I'm on the edge of Verizon plan, which allows me to update when I want if I don't care keep my phone or get money to trade it.  I'm two months from own the phone outright, but I will probably go to a Samsung better buy a promotion gift card $ 150 to go to Samsung and trade in my iPhone.  I'm an advocate of Apple for a long time, but clearly widespread lack of solution to this problem is not a good look for a company that built themselves on the convenience and simplicity.

  After two months of headaches, I feel like it's worth to wait until March and I should not have to this fact.

  You have a question or you did he yell?