Marked by mistake to a partition 'Active'. Cannot access my XPS L501X.

Similar Questions

• Error: "the process cannot access the file because it is being used by another process." when treid to install the device driver

  Original title: Windows cannot install the drivers

  I had a lot of trouble installing the drivers on my Windows computer.  I went straight in the Device Manager and deleted the devices I tried to install and reinstalled them, I went into safe mode, I got Windows to run the console and only the basic process and run from there Device Manager... no matter what I do the same mistake.

  "The process cannot access the file because it is being used by another process".

  Even after a restore of the system, he did this, and I don't know what to do anymore.  Only devices that have been previously installed work.

  What's more important install my Blackberry software because my phone is broken.  The software cannot detect my phone because the drivers have not been installed.  Most of the devices I can use with Linux (I have Windows Vista and Ubuntu running on the same computer), but RIM don't make Blackberry for Linux software, so I have to do it on Windows.

  Hi paco2012,
   
  1. did you of recent changes on the computer?
  2. how many user accounts you have on the computer?
   
  Try these steps and check the result.
  Step 1: Install the driver as an administrator
  a. shut down the computer runs.
  b. start the computer and the connection as an administrator.
  c. find the driver configuration file, right-click on the file and click "Run as Administrator".
  d. follow the instructions in the wizard to install the driver.
  e. restart the computer once the driver is installed.
   
  Step 2: Try to install the driver to boot either by disabling all non-Microsoft programs
  a. open the article: http://support.microsoft.com/kb/929135
  b. Article, follow "step 1: perform a clean boot."
  c. restart the computer.
  d. install the driver and verify the result.
  e. follow "step 7: reset the computer to start as usual.
   
  Kind regards
  Syed - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Why the Dell recovery partition is marked as partition active?

  As far as I know the active partition where the bootloader. So I have a few questions:

  How the recovery partition to load windows?

  Could not Dell set the Windows partition active? If I do it myself that I would not be able to access?

  Is this partition created by Dell or have I not this option with a non - OEM Windows copy as well?

  Hello VYOAMA

  You are right that the boot loader is located on the active partition.

  Your next question how it load windows? Instructions in the bootloader show

  When windows is located on the disc and load it where. The old directory of BACK

  has almost disappeared since the bootloader it uses and compensate for finding things on the disk.

  Your next question about Dell implementation active Windows partition? Yes, and on some systems

  and not on others. Your next question to yourself and that you would not be able

  to access? One thing you cannot access is back at the factory. Once the connection between

  Partition and windows partition recovery is broken cannot use F8 to recover the original image.

  Your next question, yes Dell partition configuration, but it is a version of Microsoft Windows and you can

  Create your recovery partition, the system, the partition to the OS partition and set the place in several ways.

  Hope this answer some of your questions and always back up your computer before changing

  things.

  Tom

• How to set the partition active windows 7 using the command line

  I activated the system recovery partition, so the windows partition is disabled and I can't start Windows

  Partition Wizard Home Edition:
  (There is also a CD bootable version, this allows to change the partition 'Active')
  http://www.partitionwizard.com/free-partition-manager.html
  Some of the features and functions include: resize and move partitions, Partition recovery after an accidental deletion, Create partition, Delete partition, format partition, convert partition, partition Explore, Hide partition, change the drive letter, the active value partition.
  Note: To complete any task use the "Pending Operations" box at the bottom left.

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• ORA-14086: a partitioned index cannot be reconstructed as a whole

  Hello
  
  I'm trying to rebuld index had error below.
  
  SQL > alter index rms12. PRICE_HIST_I1 regeneration;
  ALTER index rms12. PRICE_HIST_I1 rebuild
  *
  ERROR on line 1:
  ORA-14086: a partitioned index cannot be reconstructed as a whole
  
  Select index_name, separated from dba_indexes where table_name = 'PRICE_HIST '.
  
  o/p
  
  Index_name partitioned
  
  PRICE_HIST_I2 YES
  PRICE_HIST_I1 YES
  
  Thank you

  If you need to find the names of partition in dba_ind_paritions.

  ------
  Sybrand Bakker
  Senior Oracle DBA

• Why the partitioned table cannot create?

  Why the partitioned table cannot successfully create?

  SQL> create table hr.gps_log_his
    2  (id number,
    3  name varchar2(10),
    4  time date)
    5  tablespace ts_log_his
    6  PARTITION BY RANGE (TIME)
    7  (PARTITION udp_part2009110707 VALUES LESS THAN (TO_DATE('2009110708','yyyymmddhh24')),
    8  PARTITION udp_part2009110708 VALUES LESS THAN (TO_DATE('2009110709','yyyymmddhh24')),
    9  PARTITION udp_part2009110709 VALUES LESS THAN (TO_DATE('2009110710','yyyymmddhh24')),
   10  );
  )
  *
  Error in line 10:
  ORA-14004: Missing PARTITION key word.

  Hello

  Your problem is the comma ending line 9. Delete this.

  Concerning
  Peter

• New user cannot access any area of activity

  Hi, I use Discoverer Desktop 9.0.4.43.17 and administrator of 9.0.4.43.18 and I have a new user cannot access any sector of activity, I tried to create a new business district to test and access the Security window on the Client of Directors for this user and my user (works very well!), for my user that this new BA shows normally on the desktop but for new user the selection of business on Assistant workbook area shows nothing. It's something to measure new users to access the space business?
  
  Published by: user2997975 on 06/04/2009 07:19

  Hello
  As suggested by Rod it sounds as if you may have several EUL in the same prod73. Try to connect again, but this time go to tools | Options and click the EUL. It is the last tab on the right side and you may need to click the button to the right (next to connection) several times before seeing the EUL tab.

  Under the EUL tab, make sure that the EUL you want to connect is selected. If it is bad you will need to change it, click on the OK button and then reconnect to the database using file | Connect to the database.

  This time you must point to the right EUL.

  Best wishes
  Michael

• 8 computer is a mess... running XP WP 7 - cannot access tools, many mistakes see the cigarette... What can I do? cannot afford the new computer.

  8 computer is a mess... I am running Windows XP seven.

  Cannot access tools, show many errors, see the following issues...
  ERROR CODE 0 X 80070715
  ERROR CODE FOR INSTALLING WINDOWS DEFENDER
  HTTP ERRORS - directory 404 not found
  SCRIPTS - you run Scripts (gives an explanation by saying "If you continue to run scripts, that can compromise your computer")
  -the choice to continue running scripts or stop script execution...
  WEBPAGE SCRIPT ERRORS
  PUBLISHER 2010 does not run or act as it did when first installed...

  Then... I get...

  TO BLOCK OR UNBLOCK A PUBLISHER

  Internet Explorer allows you to block or allow downloadable software publishers. The Publisher is identified by the digital signature applied to the file that is downloaded. If the file is not signed, changing these settings will have no effect. For more information about digital signatures and certificates, click related topics.

  To block an editor

  If a file is downloaded to your computer, you will see a security warning dialog box. If it has a button more options , you have the possibility of preventing the download more software on your computer of this editor.

  1. In the security warning message, click more options.
  2. Click never install the software of the name of the Publisher.

  As you can see... I need to go to the 'TOOLS' to change anything on my computer... not able to access the 'TOOLS '.

  To assign an Web site to a Security - Zone could not be opened for this...

  Can someone help me with a single blow to properly operate my computer? Impossible to buy a new laptop because without finance.

  Laid off in March 2013 and need this laptop to find and apply for a new job.

  Thank you very much, Mr. VMW
  

  ... Can someone help me with a single blow to properly operate my computer?

  If this is the result of infection by the virus scanner Malwarebytes on the machine.

  Also:
  How to start the System Restore tool by using the option of safe mode with the command prompt in Windows XP

  John

• Activation of Windows 7 - Windows cannot access the specified device

  I enter a new key in my computer, it says that it is not genuine now.

  When I try and and activate by clicking on the link activate it says:

  S read - C:\Windows\system32\slui.exe pop-up box, with following information inside the box:

  "Windows cannot access the specified device, path or file. You can not have the appropriate permissions to access the item.

  I am the only user on the system and I am an administrator.

  When I tried to run slui.exe 4 cmd prompt increased from I got access denied.

  Thank you

  Thank you for your help. In fact, I could solve the problem of installing the SP1, and then uninstall Windows Genuine Advantage was an option of front.

  Thank you once again

• Cannot access the active market

  I have CC student edition and Professor of . However I cannot access assets Adobe market.

  According to the Adobe's FAQ (creative cloud help |) Market creative cloud) I should be able to use it but it says that I need to improve, because the asset is a feature of the premium.

  Also, I contacted Adobe twice so far, and they said they would be more closely and solve it within 3 days of work. It was two weeks ago and I'm getting worked up a little.

  I could really use tricks of the market for my projects.

  So far, I must say that Adobe might be a little more talkative about their problems and issues (also posted a question about Adobe form that remains unanswered). Excellent products, but when there are glitches they remain strangely silent.

  concerning

  Please check "PRIVATE MESSAGE".

  Concerning

  Megha Rawat

• Lenovo 3000 N200 - cannot access Rescue and Recovery - MBR poss problem?

  I have a Lenovo 3000 N200 sick who was running XP home. I could not start XP and can only access the Rescue and Recovery utility in the Lenovo recovery Partition that would be to rebuild the hard drive to factory settings IE. Windows XP with no data. I managed to copy the data using a Paragon backup cd and then made the fatal mistake of attempting a repair MBR, which was a very tempting option on the Paragon rescue cd. Now, not only it does not boot to XP, but I can run is even more Rescue and Recovery to reinstall XP which is the problem!

  If I boot with windows install disc and take the option recovery console it stops, statement that "recovery console could not find the hard drives connected to your computer. Setup cannot continue. "

  I was wondering if someone another backup MBR restore could help me with this?

  So, if someone has a Lenovo 3000 N200 work and is willing to try to save the MBR to send it to me, then please get in touch. It is probably useful to make a backup for yourself where the same problems happen to you!  In my view, there are a bunch of programs that backup the MBR for example MBRtool, MBRWizard and so on.

  Any ideas, offer accepted with gratitude.

  Yes I know I could buy the Lenovo recovery disk, but it is a matter of principle for me avoid paying £50 or so if I can avoid it! We'll see if we can help here...

  Thank you

  Simonides

  I am pleased Andyp!

  The solution was to set the primary partition to inactive and value the recovery partition Active, then restart and use the Lenovo Care button (now finally works) to access the function of recovery so I could return the laptop to factory State.

  No doubt there are plenty of ways to do it, but the approach I took to solve this problem is released under

  1. use another PC to download Paragon backup and restore (I actually used the trial edition now but the free edition may have a similar feature)

  2nd burn a CD bootable backup and recovery 10.0.

  3. start the CD Lenovo, and after a long wait, a menu should appear with 11 options, the first of them being Paragon backup and restore.

  4. Select Paragon backup and restore.

  5 select properties in the pick a task window and you will see two partitions, a big enough (in my case Go 143, called Preload) and the other is quite small (6 GB called SERVICEV001).

  Note: this is an opportunity brilliant to use the Back Up Partition option to make a backup on external drive USB of the two partitions as the reconstruction of the hard drive with Lenovo Care button you will lose all data.

  6 right-click the partition preloads and select Edit and set idle

  7. made the SERVICEV001 partition right click and select Edit and set the Active

  8 remove the backup and recovery of CD and put it somewhere safe

  9. restart the PC and Lenovo Care button (might be called something different) should now work, allowing you to restore the hard drive to factory settings which will erase all data of a personal nature. You did a backup?

  10 Windows should then start as usual, reinstall Paragon backup and restore, and restore your data.

  Finally, look at this as a lesson to

  (a) you get a writable DVD and use the Lenovo menu under windows to create a floppy disk from Lenovo rescue and recovery started.

  (b) use Paragon or equivalent to create copies of images of each partition and ordinary differential copies of the primary partition.

  I hope this will help other owners who have a hidden rescue for example partition. IBM and HP and would like to receive feedback.

  Finally, I must acknowledge assistance patient e-mail provided by Taisia Smirnova Paragon support by offering me this solution.

  best, Simonides

  (If you found this helpful please click on the star to give me a point Bravo!)

• Trying to repair XP Home CD, but cannot access the screen where you choose to repair or install fresh.

  Trying to repair XP Home CD, but cannot access the screen where you choose to repair or install fresh.

  I get the first screen where you have the choice to configure windows or press 'r' for recovery console.

  After I press enter for the installer, do not me the usual on-screen next where it is said that if the following XP installation is damaged, you can repair it.  Instead, it leads me to a screen where it shows my partitions and asked that one I want to install windows on.  If I choose "C:" he then told me that there is already a system opperating on the partition...

  Hello

  Follow the steps of "Error Message: Setup cannot set the required Windows XP Configuration Information.
  ' http://support.microsoft.com/kb/316425 '.

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• 0X803C0107 error: you cannot access shared files and printers and the MSE does not start at startup

  Original title: mainly MSE does not start at startup. have you tried re-loading and other elements on the card, still no luck. Here is the error code I have and the information complete.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • Error 0X803C0107

    Details of the editor for Windows Firewall troubleshooting

    Verified issues

    You cannot access shared files and PrintersYou cannot access shared files and printers

    You can't access shared folders or printers on a computer on which Windows Firewall is enabled. This happens when the Windows Firewall blocks traffic entering via the UDP ports 137 and 138 and the ports TCP 139 and 445. Checked

    No workingRemote Assistance remote assistance does not

    When you use Windows Help and Support, remote support available to offer assistance to a computer, you receive the error message "the remote server computer does not exist or is unavailable", even if Remote Assistance and file sharing and printing are activated. Windows Firewall may be blocking Remote Assistance. Checked

    Windows Vista may not start Windows Vista FirewallWindows could not start the Windows Firewall

    On a computer that is running Windows Vista, you find that the Windows Firewall service is not running. When you try to manually start the service, you get "Windows didn't start the Windows Firewall on the Local computer." For more information, see the system event log. If it is a non-Microsoft service, contact the service vendor and refer to service particular 5 error code. "error message. This can occur if the 'MpsSvc' account does not have the necessary permissions for the registry keys concerned. Checked

    Windows Firewall service is not his firewall service is not started

    Windows Firewall service is not running or is not started. Checked

    Issues checked the details of the detection

    6 you cannot access shared files and printers checked

    You can't access shared folders or printers on a computer on which Windows Firewall is enabled. This happens when the Windows Firewall blocks traffic entering via the UDP ports 137 and 138 and the ports TCP 139 and 445.

    Unlock the file and printer sharing in Windows Firewall works not

    To allow access to shared folders and printers, except for the file sharing and printers in the Windows Firewall must be enabled.

    6 remote assistance works not verified

    When you use Windows Help and Support, remote support available to offer assistance to a computer, you receive the error message "the remote server computer does not exist or is unavailable", even if Remote Assistance and file sharing and printing are activated. Windows Firewall may be blocking Remote Assistance.

    Allow Remote Assistance in Windows not running Firewall

    Which allows Assistance remotely as an exception in Windows Firewall it unlocks and corrects this problem.

    6 Windows Vista could not start Windows Firewall check

    On a computer that is running Windows Vista, you find that the Windows Firewall service is not running. When you try to manually start the service, you get "Windows didn't start the Windows Firewall on the Local computer." For more information, see the system event log. If it is a non-Microsoft service, contact the service vendor and refer to service particular 5 error code. "error message. This can occur if the 'MpsSvc' account does not have the necessary permissions for the registry keys concerned.

    Set permissions for the registry keys concerned not run

    Setting permissions for the registry keys concerned will solve this problem. Applies only to computers by using Group Policy to manage the firewall.

  6 Windows Firewall service did not start Checked

  Windows Firewall service is not running or is not started.

  Start the Windows Firewall service is not running

  Start the Windows Firewall service solves this problem.

  Details of detection

  Collection information

  Computer name: NORMBRESINSKI

  Windows Version: 5.1

  Architecture: x 86

  Time: 09-20-2010 07:51:49

  Publisher details

  Troubleshooting Windows Firewall

  Automatically fix problems of Windows Firewall, such as Windows cannot start the firewall service (0x5) Windows or Windows remote assistance does not work

  Package Version: 1.0

  Publisher: Microsoft Corporation

  You have problems with programs

• Error messages
• Recent changes to your computer
• What you have already tried to solve the problem

Hi Rickbsk,

You can check out the link and check the suggestions provided by scotty1294.

http://social.answers.Microsoft.com/forums/en-us/msestart/thread/05a63b12-1be9-4BD3-898e-64674c1e9afd

If you have not tried all the suggestions above, try and see if it helps.

Hope this information is useful.

Jeremy K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• executable files: cannot access the file because it is being used by another process

  Hello
  I created a file named test.bat on my desk
  baptized "test.bat" and sent the notebook, wrote "REM" and recorded.
  so, I closed my notebook and reopened, has added another "REM" and saved the file again.
  then I tried to rename, move the file to another folder and delete
  everything went without any problems.

  But if I create the file and run it, the command prompt will appear for a while and then disappear.
  I can rename or move the file without any problem,
  But if I try to edit the file in Notepad, I get this error:

  The process cannot access the file because it is being used by another process.

  and the file is not saved.

  also, if I try to delete the file, it seems to be deleted until I press F5, the file appears again.
  When you try to rename/move this new file, I get another error:

  File Access Denied

  You need permission to perform this action

  You need the permission of the administrator of the computer to make changes
  in this file

  It seems the file is opened (or if I choose to delete) after a few minutes, then it is not if I try to access
  the file (I kept pressing F5 every few seconds for 15 minutes and the file is missing)

  the problem appears if occuar with any file name, anywhere, not just the office or home by car, not even on the same disk,
  while I had no problem when I started in an old installation of windows xp and repeat the same steps.

  I tried to use the sysinternals utility handle, that's what I have:

  After creating test.bat:
  C:\Users\User>handle test.bat

  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  No found the corresponding handle.

  After you run test.bat:

  C:\Users\User>handle test.bat

  Handle v3.51
  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  System pid: 4 type: file A18: C:\Users\User\Desktop\t
  EST.bat

  has obtained the result above after attempting to remove test.bat also.

  After the creation of othertest.bat:

  C:\Users\User>handle othertest.bat

  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  No found the corresponding handle.

  After execution of othertest.bat:

  C:\Users\User>handle othertest.bat

  Handle v3.51
  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  System pid: 4 type: BD0 file: C:\Users\User\Desktop\o
  thertest.bat

  After you rename the othertest.bat:

  C:\Users\User>handle othertest.bat

  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  No found the corresponding handle.

  C:\Users\User>handle renamedtest.bat

  Handle v3.51
  Copyright (C) 1997-2013 Mark Russinovich
  Sysinternals - www.sysinternals.com

  System pid: 4 type: BD0 file: C:\Users\User\Desktop\r
  enamedtest.bat

  the also occuars when I run any .exe file and delete it after its finished running, I deleted
  the handle.exe and the handle64.exe after the test above and at the same time returned when I updated their records.

  can someone help me?
  IAM using Windows 7 ultimate 64-bit.
  Thank you.

  I struggled with this VERY ENNUYANT thing for a long time on a Windows Server 2008 R2.

  Just found the answer:

  http://superuser.com/questions/260375/why-would-system-continue-locking-executable-file-handles-after-the-app-has-exit

  Activation of the service 'Application Experience' does the trick for me.

  If I got paid for every minute spent dealing with the mysteries of Microsoft... No, wait! Paid!

  Thank you Microsoft!

• WES7: 'Windows cannot access the installation sources. "Check that the installation sources are accessible and restart the installation.

  I try to install Windows Embedded Standard 7 on an vacuum Compact Flash 4 GB but when installing, I get an error message "Windows cannot access the installation sources. "Check that the installation sources are accessible, and run the Setup again."

  I created an answer file with the Configuration of Image Editor and I created an Image of the IBW of my answer file. All the files and the Image of the IBW (738 MB) files are copied to a USB bootable 4 GB. I inserted the Flash DRIVE to a computer with a Compact Flash 4 GB (which contains only a primary NTFS partition set as Active) and it starts on a USB key. IBW Wizard starts and I followed the instructions until the disk selection step. I chose the disk and partition of Compact Flash and I press the next button. First 2 installation steps manage (copy of Windows files and extend Windows files) but 3rd step (installing features and updates) failed with the error message "Windows cannot access the installation sources. Check that the installation sources are accessible, and run the Setup again.'.»

  I tried to do the same thing with a Compact Flash 4 GB, which contains 2 partitions: a primary NTFS defined as active and a system partition, but I got the same result. Then I tried to install it on a Compact Flash 8 GB which contains 1 single defined primary partition as active and I managed.

  Problem is that I must install on a Compact Flash 4 GB.

  Can someone help me please?

  For Windows Embedded-related problems, please post in the forum on TechNet:

  http://social.technet.Microsoft.com/forums/en-us/category/windowsembedded