material conditions VSA?

Similar Questions

• Error message 6700 - problem with the printer or ink

  
  

  There is a document with steps to help solve this type of printing errors.  Click here to access the troubleshooting document.

  If you have done all the troubleshooting steps, and the error is still present, the printer has developed an internal material condition.  If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  Technical Support case HP formula call: https://h10025.www1.hp.com/ewfrf/wc/phoneInput?cc=us&dlc=en&lc=en&product=5061082

• SG300 - 28 p: POE power drops every few minutes

  Hi all

  We have a SG300 - 28 p which, at intervals between 5 and 30 minutes or more, lower power to all its ports POE-powered and then immediately restores power. Switch logs nothing when this happens other than to record that the ports went down and back up, even with debug logging enabled. Non - POE ports are not affected.

  When the problem started there were only four POE devices on the switch and we are far under our power budget. (During the test, I added a fifth device, see below.)

  Not all combinations of devices cause the drops occur - specifically, it seems that having devices on ports next to each other causing the drops. When the drops occur, absent the increment of POE devices all counters. I noticed this thread earlier here seemed similar:

  https://supportforums.Cisco.com/thread/2165089

  but in this case, he got no power at all in the adjacent configurations, instead of having to drop all the several minutes.

  I am running

  SW06 #sh worm

  SW version 1.1.2.0 (November 12, 2011 time 23:34:26)

  Start the 1.1.0.6 version (date may 11, 2011 time 18:31)

  HW version V02

  I have the 1.2.2.7.6 ready to go new firmware, I will update this when I get a chance to test it. Unfortunately, it's a switch of production, but it's a with relatively few devices to it so far. If need be, I have a sf300 - 48P I can exchange this sg300 ENJOI trials.

  Thank you for anything you might suggest.

  Here are the details:

  -' Phone' is a phone to IP Avaya 4610SW or 5610SW (class 2)

  -"Watchdog" is an environmental monitor IT Watchdogs Watchdog 100 (class 0)

  -"WAP" is a Cisco WAP4410N (class 3)

  All initially due to lack of combination:

  GI10 phone #1

  gi22 phone #2

  dog guard gi23

  WAP gi24

  would result in the POE power to place on all ports, every 5 to 30 minutes.

  I disabled Green Ethernet completely - no change.

  And then made the following tests:

  1. "power never inline" on gi23 and gi24: problem disappeared

  2. 'inline power auto"on gi23 and gi24: problem is back

  3 ' power inline never' on gi23 only: problem disappeared

  4 ' auto of inline power' on gi23: problem is back

  5 ' power inline never' on gi24 only: problem disappeared

  6. "power inline auto" on gi24: problem is back.

  I left gi23 powered throughout the night and it was stable: it's about 10 hours without any problem.

  This morning, tried the following configs:

  08:54 - worked fine

  IG4 watchdog

  GI10 phone #1

  gi22 phone #2

  WAP gi24

  10:31 - added another phone, the problem came back

  IG4 watchdog

  GI10 phone #1

  gi22 phone #2

  gi23 phone #3

  WAP gi24

  10:43 - inappropriate phone #3 to IG11 (next) - problem continues

  IG4 watchdog

  GI10 phone #1

  IG11 phone #3

  gi22 phone #2

  WAP gi24

  11:00 - moved phone #3 to gi8 - suite problem

  IG4 watchdog

  gi8 phone #3

  GI10 phone #1

  gi22 phone #2

  WAP gi24

  11:31 - moved phone #3 article IG 14 - the problem disappeared

  IG4 watchdog

  GI10 phone #1

  Article IG 14 phone #3

  gi22 phone #2

  WAP gi24

  and that's where we left things now are stable for about four hours.

  The following products are the config more later (11:31).

  SW06 #show power inline

  Power-limit based port mode

  Nominal consumed power unit power use threshold traps

  ---- ------- ------------- ------------------ --------------- ---------

  1 of 180 Watts 18 Watts (10%)         Disable 95

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  Article IG1 Auto search low class0

  IG2 Auto search low class0

  IG3 Auto search low class0

  IG4 Auto on low class0

  IG5 Auto search low class0

  GI6 Auto search low class0

  gi7 Auto search low class0

  gi8 Auto search low class0

  gi9 Auto search low class0

  GI10 Auto on low 2

  IG11 Auto search low class0

  gi12 Auto search low class0

  ig13 Auto search low class0

  IG 14 Auto article on low 2

  gi15 Auto search low class0

  gi16 research Auto low class0

  IG17 Auto search low class0

  gi18 Auto search low class0

  IG19 Auto search low class0

  IG20 Auto search low class0

  IG21 Auto search low class0

  gi22 Auto on low 2

  gi23 research Auto low class0

  gi24 - Auto on low class3

  -watchdog:

  SW06 #show power inline IG4

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  IG4 Auto on low class0

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Absent of meter: 4

  Invalid Signature counter: 0

  SW06 #show interfaces announce IG4

  Port: IG4

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  -Phone:

  #show power inline gi10 SW06

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  GI10 Auto on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 465

  Invalid Signature counter: 0

  #show int adv gi10 SW06

  Port: gi10

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  -Phone:

  SW06 #show power inline article IG 14

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  IG 14 Auto article on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Absent against: 0

  Invalid Signature counter: 0

  SW06 #show int adv article IG 14

  Port: article IG 14

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  SW06 #.

  -Phone:

  #show power inline gi22 SW06

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi22 Auto on low 2

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 591

  Invalid Signature counter: 166

  #show int adv gi22 SW06

  Port: gi22

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no Yes Yes Yes Yes

  Resolution of priority - Yes-

  --also was the watchdog, now empty:

  SW06 #show power inline gi23

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi23 research Auto low class0

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is disabled - detection is in progress

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 587

  Invalid Signature counter: 0

  -wap:

  SW06 #show power inline gi24

  Port power status device status priority class

  -------- -------------------- ---------------- ------------ -------- ---------

  gi24 - Auto on low class3

  Limit of power (for the mode of power-limit of port): 15.400W

  State of the port: Port is on - valid resistance detected

  Overload counter: 0

  Brief of counter: 0

  Denied Counter: 0

  Missing Counter: 607

  Invalid Signature counter: 3

  SW06 #show int adv gi24

  Port: gi24

  Type: 1 G-copper

  Link state:

  Autonegotiation: enabled

  1000F 1000 h 100f 100 h 10 h 10f

  -----  -----  ----  ----  ---  ---

  Link admin Local advertising Yes No Yes Yes Yes Yes

  Local liaison Oper announced Yes No Yes Yes Yes Yes

  Oper Remote link Announces no no yes no no no

  Resolution of priority - Yes-

  Other useful bits:

  SW06 active spanning tree #show

  Spanning tree disabled mode (floods BPDU) RSTP

  By default port cost method: long

  SW06 #sh worm

  SW version 1.1.2.0 (November 12, 2011 time 23:34:26)

  Start the 1.1.0.6 version (date may 11, 2011 time 18:31)

  HW version V02

  Hi Rich, reference this photo I just drew is a rough interpretation of how a switch 24 ports has guts. Each + block represents a processor. The numbers below represent the port Bank that corresponds to the transformer. Of course, MODULE POE is clearly identified. Each module 12 POE ports for services.

  I think you have a completely different question. If the POE works for 5 to 30 minutes, it can be a problem of layer 1 (bad son) or a different, perhaps material condition being disturbed. If the switch is at fault, it seems more likely to be defective to a unit of buggy.  I did a lot of research on the operation of the switch ASIC, transformer and modules of POE in the cohesion.

  Quite frankly, I think you should go to the 1.2.7.76 firmware, factory reset the device and test all the ports you want using the same equipment. If maintaining the POE fall every 5 to 30 minutes and you are absolutely positive, that it is not a question of layer 1 or a configuration problem on your products, can I just replace the switch.

  

  -Tom
  Please evaluate the useful messages

• Upgrade of the os to blackBerry Smartphones

  Is it possible to upgrade my bold 9780 os 6 to 7 os, it's only a few months

  No, it is not and it will never.  7 OS needs some material conditions that are not present in the Bold 9780.

  I hope that answers your question.

• EBS networking

  Hi all

  Firstly excuse me with poster on this thread who maybe does belong here.

  We have a customer with zero according to IT. And I wanted to buy EBS R12.2.4 small accounting. (small only)

  We have a proposal of costs for the EBS software + hardware.

  But they want to include the cost of networking also.

  What are the material condition basic/less expensive / the solution to start a small network?

  for example no wiring but all wireless wi - fi?

  Can you give me link for setting up small cheap put base on a network for a small office? No wiring, but all the wifi wireless?

  Should I upgrade? router? hub? etc.

  There the networking for beginners or Dummies EBS

  Thank you ALL

  Hello

  As much as I KNOW, no, is not a guide specific to the EBS network.

  You only need a connectivity that is stable and relatively fast.

  This is not related to BSE.

  You should post in a networking forum.

  Kind regards

  Bashar

• Components of identity management

  Hello
  
  We plan to go with the Installation of the identity management which is part of the Fusion Applications. So I would like to know what are the elements that arise as part of Installation of identity management and what would be the material condition for the Installation of identity management.
  
  Kind regards
  CV

  See certification matrix for hardware and all kinds of requirement:
  http://www.Oracle.com/technetwork/middleware/ID-Mgmt/identity-accessmgmt-11gr2certmatrix-1714221.xls

  This is for Oracle identity management. Its main components are:
  -Oracle database
  -Java 1.6
  -Weblogic server
  -Oracle Identity Manager
  -Server SOA
  -Repository creation utility

  Kind regards
  GP

• A few questions about Essentials Plus & opinion

  Hi all

  Been a lurker here for a while and learned a lot but now I have a few questions, if you don't mind.

  I have a client for which Essentials would be a great choice both in their material conditions and pricing, but they also want a little too VDI solution.

  So my first question is if we view can we use comes with more Essentials VCenter to manage? Or at least link them?

  And also, on the safeguarding of their infrastructure plan - is it possible to use Backup Exec 2010 with their (from Symantec) "Agent for VMware Virtual Infrastructure license? Or the absence of VCB in Essentials more do we need to go back to the backup of the OS invited by agent?

  It's pretty strange - I'm competent with VMware in all, but this is the first time that I had to consider using Essentials, so I'm really not updated on what it can/cannot do / limits.

  Thanks in advance.

  Tony.

  It is not possible to link the VCenter comes with Essentials more to one that comes with a view

  The problem is that vCenter essential is an edition of Foundation and cannot manage 3 guests.

  It assumes that it can then be even backtracked on tape with a normal file-based backup procedure?

  Yes... but don't forget to do during the job no. VDR is running.

  I also realized that Essentials more was considered as a product without issue with no path uprgade (!) is always true?

  You can upgrade essential more to an acceleration of the advantage kit.

  Then you can upgrade to higher version.

  But only if the SnS is still active.

  André

• VSA on material different hosts in a cluster

  I installed VSA attemtped to VSA configuration for two hosts in a cluster with a different material and successfully. When I have case set up the ASB I couldn't add any of the hosts in the cluster. In the details, he says "guests shouldn't be in a cluster, hardware not supported." My question is...

  Should I remove the hosts in the cluster?

  VSA supports the hosts of different material?

  VSA can support my setup with a different configuration?

  I am new to VSA, so any help would be appreciated.

  Concerning

  Purpose of test, I missed more than one option you need to change in the dev.properties:

  EVC.config = false

  Turn off the host.audit allows you to select hosts even with unsupported hardware.

  This cannot be a permanent solution, because VSA configures an EVC cluster enabled as part of the workflow installation and vCenter Server does not add a host from a different family of the seller/CPU in a VCA active cluster.

• Material VSA

  Hello

  Due to a customer political Fujitsu RX200 Fijitsu S7 are used for vSphere and VMware HCL suggests that the servers are OK for running vSphere 5.1.

  We now have an additional requirement to perform new Fujitsu RX200 Fijitsu S7 servers running vSphere 5.1 and VSA. However, the HCL in the following URL does not list the Fujitsu RX200 Fijitsu S7 server to run the VSA function.

  http://www.VMware.com/resources/compatibility/search.php?deviceCategory=Server

  Did anyone know why that would be the case, for example, the server's hardware is OK for vSphere 5.1 and not VSA?

  The policy to have servers certified for the ASB has been eased recently, according to the http://blogs.vmware.com/vsphere/2012/12/major-hcl-changes-for-the-vsphere-storage-appliance-vsa.html.

  Now, you just need to make sure you have a certified Raid Controller.

  I hope this helps.

  Cormac

• How to conditionally check material list values?

  try to check the value of a property in a global list of the property.
  the two methods do not work.
  The part with the fact that I have problems the conditional statement to startmovie
  
  
  on prepareMovie
  global glistT
  Set glistT = [#A1:0, #A2:1, #A3:0, #A4:0, #A5:0]-R seats empty unless A2
  
  end
  
  on startmovie
  global glistT
  If gListT.getPos (2) = (#A2) = 1 then sprite (4) .member = member ("taken")
  end if
  end
  
  also tried
  
  
  
  on startmovie
  global glistT
  If (#A2) gListT.getOne = 1) then sprite (4) .member = member ("taken")
  end if
  end
  
  both make sense and no error but do not seem to work.
  What should happen in the chart must obtain permuted based on the properties of glistT
  There must be something small
  
  Thank you

  Thank you

  everyone... use [] instead of (), I knew that it had to be something simple like that.

  now the game is updating and reading that Glist of a text from the file on a Web server. I'll try the additional IO file first

• Index and MATCH with several conditions

  Hi all! I hope I can explain what I'm trying to do here clearly. This is my first shot:

  In the table below "Office entry Worksheet - area 1" I am trying to insert a formula in column B which will result in an answer ' true / false ' and be used for conditional highlighting

  

  The first condition that must be met is that the checkbox in the table "Labor and material Checklist" column A or check, if it is not checked, then move to the next line. If the box is checked, then the following condition would need to index and match with column C of table "Office entry Worksheet - area 1" in column B. If there is a match in column C, then move to the next line of column B in the table 'labor and material Checklist '. This continues until there is a 'match', then highlight column B in the table "entry Office sheet - surface 1" in red (or something like "MISSING task")

  It is an estimate and the idea is to ensure that the Phases that are checked in the table "Labor and material Checklist" will not miss when you use the table "entry office map - zone 1".

  Thank you very much for your help!

  Tim

  

  Is it possible that I can download this spreadsheet file?

• Portege R700 webcam goes dark in low light conditions

  Hello

  Since I bought my Toshiba Portege R700 about a year ago I had problems with my webcam. I looked in several forums but couldn't find an answer. My build in webcam has problems of adaptation in the light of the room.

  When the room is dimly lit camera turns almost black after a few seconds. It is interesting enough before the camera darkens, he manages to produce a picture is ok for a few seconds, which means that the camera is capable of producing an image ok in low light conditions.

  She has just problems adjusting the brightness in the room when it is poorly lit. I propose to toshiba update the software of the camera, since it is clearly a matter of software. And yes I've tried every single possible configuration for the camera! And Yes, I also reinstalled (several times) the camera driver.

  I know that the camera performs well in places that have good lighting and so I'm only interested in improving my performance of cameras when not much light is available.

  Thank you very much
  Clem

  Hi dude

  I understand that you would expect webcam great performance in poor light environment but I put t do you think it would be possible to get the good quality photo using the laptop is dark rooms.

  The material of these small internal cams is limited and you see the same issues with other devices like smartphones cameras that resemble the internal cams s notebook.

  In addition, the webcam software that is preinstalled on my laptop Toshiba supports the night mode option that allows you to improve the quality of the obscure image in the Middle but of course you will not get the same image quality if you want to use the cam in the luminous environment

• Analog OUTPUT material

  Hello

  My question is about the analog output (0 - 10V) of the myDAQ unit.

  On the card, you can read:

  "Overdrive Protection +-16 V forever."

  Lets imagine the worst case: 0 V output DQA, but outside a battery or anything else is connected with 15 V to the analog output.

  Fact an "unlimited" current in data acquisition or protection 'Overdrive' works here and the material is safe to destroy?

  The background: I want to OD are protected from transient voltages and toilet on a simple zener diodes clip or a tvs diode...

  Thank you all, Markus

  Markus,

  To use a zener diode as protection, you must also have an impedance of current limiting in series with the source against which you are protecting.  The manual for the device of maDAQ indicates that the lines of the AO are pushed by OPA1642 op amps.  TI the MSDS for this unit shows the current limiting internal ~ 36 my short circuit with Earth and a thermal shutdown circuit that tries to protect against the terms of overpwer.

  However, under your 15 V battery, 11 V zener and 0 V programmed DAQ exit, the situation may be different.  The current from the battery through the zener will be limited by the impedance of cables or any type of resistance on the line.  This has no direct effect on the myDAQ device, but it will probably destroy the zener unless resistance limits the current to a lower maximum current nominal zener.  As long as the voltage at the output of the myDAQ is lower than the internal supply voltage (+/-15 V), on the OPA1642 current limitation should apply.  With 11V applied to the output and the value set to zero the device would probably be to try to sink the maximum current for-15 V power supply.  Which translates to a dissipation of power of more than 900 mW, which exceeds the rated capacity of the op amp. Themal protection should, in principle, reduce the current to a level that does not exceed the thermal limit under development.

  This test can be a costly process. The unit may be destroyed.  Given that the maximum current specified for an analog output channel is 2 my and the maximum voltage is 10 V, I would consider a series resistance of perhaps 1000 ohms and clamping schottky diodes at the + 15 V and - 15 V power supply.  This will limit the current to 10-20 my in all conditions you have mentioned and would also provide protection to the case where the battery is connected the myDAQ device is turned off. He alsoe does not care about the polarity of the external source.  It will drop the output voltage according to the load impedance.  If this should be used in a student lab, the calcualtion of this decline is something they should be doing anyway, and would be a small price to pay for protection.

  Lynn

• under condition of read/write terminals on the side of the connector (basic training 3)

  Hello

  During my practice towards the review of the CLD, I examine the Core 3 online training material too. I just read a few tips of 'best practices' on the forum, for example this post:

  http://forums.NI.com/T5/LabVIEW/Community-Nugget-wired-terminals-in-subdiagrams-clearing-up-the/m-p/...

  It should be noted, that we should not use terminals (which are on the connector pane) to the inside of while loop or condition of the structure. Neither control, nor indicators (read/write terminals): "terminals conditionally read or written on the side of the connector are BAD!"

  I can find many examples in the online training materials, when the indicators and controls are placed inside while loop and the case of structures in a Subvi.

  I guess I should not do this during my review of the CLD, as they will run benchmark on my project? Should not be the core training materials updated some time? Or it's just not too important to have terminals on the outside? I would lose points during the CLD Exam my project as in the Core 3 screws?

  example 1: Core 3, exercise 4-6 design of an error-handling strategy:

  

  EDIT:

  What's even more ugly in this project, is that, in the case of 'Get empty Cue', the Cue output indicator is updated via a local variable, because the indicator is not accessible via 'outside ': wire

  

  Nice catch on the training material.  that the application would take an if subject to a review of the CLD test graders.

  As noted in the nugget: sentencing of perfomance for conditionally reached terminals is a function of the size of the data.  So, it is sometimes acceptable for simple data.  The larger point being to learn about compromise and make the right choice for your code.

  Preping for the CLD on other means of hand knowing that VI Analyzer will run on your project.  Like any other code review you walk in - know the guidelines for the review and code to ' review ' as well as 'reply spec.'

  I've not seen an instance where an example of shipping (2013 and later versions) would fail this test VIA (there are a few screws deep inside the vi.lib which can date back to before the adoption of this recommendation from style)

• The condition of the Terminal loop in a wiring SCTL

  Hi all.

  I'm relatively new to LabVIEW, and I have a little doubt with a Terminal loop condition which I think is pretty basic. When using a while loop, the VI breaks if there is no condition connected to the Terminal, even if it is a constant t. The same is also pretty explicitly mentioned hereand I think that makes perfect sense.

  Now, I am interested in some code LabVIEW FPGA on a forum post that I was living to understand better SCTLs (only the attached photo is NOT my own code, credits to Mahesh0459), and the conditional terminal in the SCTLs does not seem to be wired. When I watched the video that introduced this concept, loop a while turns out be replaced directly with a SCTL, whereupon the F constant (since the while loop) is automatically connected to the Terminal.

  So, my question is this: is it a good idea to leave the condition of the Terminal loop unwired in an FPGA VI? If so, what is the reason? Alternatively, is this SCTLs-specific behavior? If so, again, what is the reason?

  Thank you!

  Only in FPGA is fine.  The reason being that it is assumed the loop will only run for always in the material.  No no not the loop control registers some doors.