Matte screen disappeared on Satellite Pro A200

Similar Questions

• Satellite Pro A200-PSAE7: error on blue screen - ati2dvag infitive loop

  I've got Satellite Pro A200-PSAE7 with ATI Mobility Radeon HD2600. I downgraded to XP SP2. I get a blue screen saying that ati2dvag went infitive enough loop constantly. Any solution to this?

  OFFTOPIC: Why standart drivers from ati.com to display does not work? (while on my laptop of friends with also hd2600 mobilty radeon works fine).

  Hello

  > I've got Satellite Pro A200-PSAE7 with ATI Mobility Radeon HD2600. I downgraded to XP SP2. I get a blue screen saying that ati2dvag went infitive enough loop constantly. Any solution to this?

  The BSOD appears usually due to software malfunction serious matter or material.
  I think it s a software problem (driver).

  I presume that the BSOD appears why play games in most of the cases the graphics driver must be updated.
  If the XP driver from the Toshiba page will not help, you can try the graphics drivers on the www.omegadrivers.net site. 3rd third party drivers must run on your laptop. But note; 3 third-party drivers can be used only at your own risk!

  > Why standard ati.com display drivers do not work? (While on my laptop of friends with also hd2600 mobility radeon works fine).
  Cannot install the original ATI drivers on an easy path because this drivers don t support protection against overheating. Toshiba GPU drivers are slightly modified and support a protection against overheating. This protection is necessary and important as mobile graphics cards do not have large module of cooling as the GPU on to desktop computers.
  Temperature increases on the much faster laptops and so the driver graphic control performance of the GPU to reduce the internal temperature.

  That's why it of always advised and recommended to use the Toshiba drivers ;)

• Satellite Pro A200 - black screen with a blinking cursor

  Hello

  I'm new to the forum and have a big problem.
  So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor.
  Also just as the screen goes black a beep can be heard which shows windows boot.

  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  Please go into the BIOS settings and check if the HARD drive is listed there.
  The blinking cursor is a typical sign of a malfunction of the HARD drive.
  Eventually the HARD drive is dead and you need to replace it and reinstall the operating system.

  Good luck

• Re: Satellite Pro A200 - black screen after the BIOS screen

  Hello
  I'm new to the forum and have a big problem. So, any help is welcome and appreciated.

  My Satellite Pro A200 turns black after the BIOS screen and a black screen with a blinking cursor. Also just as the screen goes black a beep can be heard which shows windows boot.
  I can access the toshiba Setup screen but not the installation of security mode.

  Kind regards

  Hello

  You wrote that you can access the BIOS, but have you checked if the HARD drive is recognized properly? Perhaps because the computer cannot start HDD isn't recognized then you should check this.

  If the HARD drive is recognized, I would try a Toshiba Recovery disk recovery facility. It seems that Windows isn't able to start and if you reinstall the whole system should help get rid me of this. Go to the start menu and select the CD/DVD drive as a boot device.

  Check this box!

• Re: Satellite Pro A200 - no activity - nothing on the screen

  Hello!

  I have a lot of problems with the Toshiba Satellite Pro A200.
  Same problem for all: when you connect the power adapter led turns blue!
  When I press on "on" button the second led turns blue, the fan runs for a while, but there is not activity: nothing on the screen.
  No thing hard disk led...

  I have a lot of this problem with the Satellite A200. The motherboard is a LA - 3481P.
  I am an electronic engineer and I m specialized in laptop repair card main but I did not understand this problem.

  Can U help me telling me that maybe the defective chip?
  Thank you very much

  Hello

  I don't know if you saw that this forum is the forum of users and you should not wonder if nobody can give the exact answer. As an electronic engineer, you must know that no one can answer specifically and to find the good chip, you must run diagnostic tool.

  So I think that you need professional help. Try to contact nearest Toshiba authorized maintainer and ask for help.

  BTW: I am really interested about new comments here.

• Satellite Pro A200: There's a problem with my screen

  Hi all

  I wonder if anyone can help. Just got a Toshiba Satellite Pro A200, when I cleaned the screen, I noticed that in the Middle at the top (the part under the webcam) pushes a little and squeaks. It's not normal, I'm wrong?

  Help, please!
  Thanks in advance,
  David

  It's not easy to tell if it of normal or not in most of the cases the ASP must check the notebook and then the technician could decide if a part needs to be replaced

  I recommend you contact the ASP in your country and ask for details as well as a control of the laptop.

  Good luck

• Satellite Pro A200-1MA: blue screen STOP: 0x000000D1 Error

  Hello

  I have Toshiba Satellite Pro A200-1MA and Vista 32 bit. My problem is: when I work on my internet laptop notebook and use blue screen shows:

  http://img142.imageshack.us/my.php?image=dsc00238yh0.jpg and resets.

  Sometimes not regularly, but often enough [sometimes 1 by day, other times 3 per day].
  It becomes quite boring, I can't work on a laptop without fear, I have nevery secondly it may restart and I will lose any unsaved work.

  Thanks for help.

  Hello

  Do you use the preinstalled Toshiba image?
  I ask because sometimes the BSOD can be caused by serious software problem. But to be honest, it looks like a hardware malfunction.
  In my view, the RAM modules could be affected

  I have a 6 year old using my laptop BSOD the BSOD appeared after several hours of use one I thought that it s a faulty RAM I replaced it, but the issue was not resolved finally I discovered that the temperature affected modules of RAM alone and the laptop froze and BSOD appeared
  Finally, I checked the grids of cooling and cleaned using compressed air jet that it helped

  But buddy note; This does not mean that your problem can be caused by high temperature. It s only a hypothesis, and in my opinion, a technician of the laptop should check the laptop to ensure that's exactly wrong.

  Good luck

• Satellite Pro A200 PSAFCA: need driver Lan and screen for XP

  Hey

  Please help me!

  I just installed XP on my new satalite pro, but I had trouble with the drivers.
  For the moment, I installed most but from this site, I can't seem to find a driver that will help my network card, or my video NIVIDIA player...

  any suggestions would be very valuable

  The Satellite Pro A200 PSAFCA is unclear to me. I know the PSAE1, the PSAE4 and the PSAE7Satellite Pro A200. So could you please confirm your Pro A200 series?

  If you do not find only XP drivers on the Toshiba page I would recommend checking the LAN and graphics chip installed on the motherboard and use drivers XP from the manufacturing of the chip.

  If you need a graphic driver, I advise to use the drivers from the site www.omegadrivers.net or www.laptopvideo2go.com

  Concerning

• Satellite Pro A200 - external screen resolution

  Hello

  Is the integrated graphics card Intel GMA X 3100 in my satellite pro A200 computer laptop can support resolution 1920 x 1200?
  I want to buy a monitor external 24 ". It will work in the native resolution?

  Thank you!

  Hello

  That means the Satellite Pro A200 manual says?
  Have you checked it?

  I checked it (you can download from the Toshiba page) and there is an info.
  The laptop supports these resolutions on external TV CRT:

  -800 x 600
  -1024 x 768
  -1280 x 800
  -1280 x 1024
  -1600 x 1200
  -1920 x 1440
  -2048 x 1536

  But note; some of these resolutions may be not supported if the installed graphics driver doesn t supports!

• Satellite Pro A200-PSAE4E - computer laptop shuts down randomly

  I've had my Satellite Pro A200-PSAE4E for about a year and a half now. He ran very well most of the time, but in recent months he has been stop itself randomly. There is no warning or "Windows is shutting down" he just me using my computer to a blank screen.

  After frustrated with her, I did a full format my HARD drive and started from scratch. This does not solve the problem, and since then, the taskbar freezes. When I click on it I get the error and the hourglass cursor message "Windows Explorer is not responding... "I then have to click"restart", which makes the taskbar disappear for a few seconds before returning (usually without my sound icon).

  The laptop turns off when it is connected to the electric network with & without the battery and when running only on battery, so I excluded all power problem.

  I have considered it heats up too, but I use a block of cooling with built-in fans and has not himself in a few minutes after being hit not 24 hours, so I'm not sure that's the problem.

  Someone at - it ideas?

  I am running WIndows Vista Home Premium 32-bit if that's any help.

  Thank you.

  > It worked fine most of the time, but in recent months he has been stop itself randomly.
  > There is no warning or "Windows is shutting down" he just me using my computer to a blank screen.

  I think that the problem of overheating.
  The fact is that the laptop would be down automatically stops in order to avoid that the pieces of equipment against damage.
  In most cases this problem can be solved very easily. Using a jet of compressed air, you can remove the dust from the cooling modules and fans.
  I clean my fans from time to time, because I noticed a higher temperature and the laptop was a little stronger.

  Check it out mate

• Cannot ping localhost - error code 2 on Satellite Pro A200

  Dear COMPUTER gurus,

  I have a portable Satellite Pro A200.
  When I ping the local host, it says could not contact the pilot of intellectual property, error code 2.
  I tried to fix the winsock using articles from microsoft without success.

  Now I want to reapair the operating system using the recovery DVD.

  The recovery DVD has a repair option?
  If this isn't the case, anyone how to solve this problem?

  Help please!
  This is the result, I was using the pc diagnostic tool.

  Date 2008-08-30 01:47:12

  [Information on PC]
  Model name Satellite Pro A200
  Part number PSAF4U - 004 00D
  Serial number Y7312740Q
  Version of the OS Microsoft Windows XP Professional 5.1.2600 Service Pack 2
  BIOS Version 1.70
  Processor Intel (r) Core (TM) 2 Duo processor T7250 @ 2.00 GHz
  RAM 1024MB of physical memory
  Disk capacity hard 120,031,511,040 [bytes] 111.788 [GB]
  Capacity of the hard drive space free 92,245,069,824 [bytes] 85.910 [GB]
  Version Mobile Intel (r) 965 Express Chipset Family video = 6.14.10.4833
  Screen resolution 1280 x 768 Pixels
  Color quality, true color (32 bit)
  Audio version of Realtek High Definition Audio = 5.10.0.5440
  Network Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller = 10.14.6.3 version = MAC address
  Intel (r) PRO/Wireless 3945ABG Network Connection version = 11.1.0.100 references MAC address =
  TOSHIBA Software Modem Modem version = 2.1.77.0
  Version of the IDE Device 1 TSSTcorp CDDVDW TS-L632H FW = TO01
  Interface IDE 2 no
  Interface IDE 3 no
  Interface IDE 4 no
  IDE Device 5 Hitachi HTS542512K9SA00
  Interface IDE 6 no
  Internet Explorer 7.0.5730.11

  Hello

  > I tried to fix the Winsock by using the Microsoft s articles with no luck
  I guess you're meaning to this MS article knowledge base:
  [How to determine and to recover from Winsock2 corruption in Windows Server 2003, Windows XP, and in Windows Vista: http://support.microsoft.com/kb/811259]

  Well, I searched a bit around and discovered that the solution described in article 811259 doesn t help in all cases

  So searched the Web of the 3rd party site and someone has suggested to try these tips.
  It s also from Microsoft:
  * [How to reset the Protocol Internet (TCP/IP) in Windows XP | http://support.microsoft.com/kb/299357] *.

  So check it out maybe it helps

  If not, then you may be forced to reinstall your operating system, because the repair option is not included in the Toshiba Recovery CD ;(

  Concerning

• Seeing white on Satellite Pro A200

  The screen of my computer (Satellite Pro A200 - PSAE7) became white and will not normalize. This happens as soon as the boot. However, other processes are underway normally. Currently, I have to rely on an external monitor or LCD projector to allow me to continue my work.

  What could be wrong and what can do?

  Hey,.

  > Currently I have to rely on an external monitor or LCD projector to allow me to continue my work.
  This means that an external monitor works properly, no?

  Well, there are two possible reasons: either the internal LCD screen is defective or LCD cable but the graphics card and the software are ok if everything works on an external monitor.

  You see a picture if you move the internal screen a little? So, you can check if there is a bad connection. If you are familiar with the disassembly of the laptop, you can open Notepad and check the connection also.

  An alternative you can also ask a maintainer approved assistance. Disassembly of the laptop is not a problem for guys so just get in contact with them. ;)

• Satellite Pro A200 cannot connect to the wireless network

  Hello

  I have a Satellite Pro A200 and Tuesday night I was able to connect to a wireless network. I received an update, rebooted and now it doesn t seem to work.

  I can see the wireless networks available via the Toshiba Radar but cannot connect to my usual wireless network.
  Also, the wireless network icon disappeared from my system tray and if I go to Control Panel/network connections, I can't even view available networks because there is no option to do so.

  Any ideas?
  the FN/F8 will work?
  Help! Please, I beg you!

  Have you tried using System Restore and restore the operating system on time earlier?
  Maybe this will remove the update installed, and you can again use the WLAN.

  Check it out.

• Satellite Pro A200-CH7 - flickering on external monitor

  I have a Satellite Pro A200-CH7 and have the same problem with my external monitor.

  It's a Viewsonic VX2262WM of 22 "and I see flashing on the screen. I tried the monitor on another laptop and it worked fine.
  The question is the graphics of cards my Toshiba laptop.

  Hello

  Perhaps twinkle could be linked to bad land?
  Sometimes, this could affect the external display.

  Please check if the problem goes away if you unplug the adapter from the laptop

  Welcome them

• Satellite Pro A200 - failed to retrieve deaths

  Hello

  My daughter has a Satellite Pro A200 which appears to be dead, she should try to get a new one!

  When I try to boot from the HDD Recovery repair Windows I get the message "the installed program cannot start. Click OK to turn off the computer. »

  I also tried to boot from the CD/DVD drive with the disk and computer repair recovery, how I get - a black screen with mouse cursor leading to the same message as to the approach of HARD drive recovery

  Given both fail this probable failure of HARD drive (I had a similar problem with my Dell wife to start up which is HARD drive failure)?

  Thank you

  Obviously, something is wrong with the preinstalled operating system and that you need to do is to install the operating system using Toshiba recovery image.

  First enter the BIOS settings and be sure the HARD drive is recognized correctly.
  Set the BIOS to default settings and start recovery image installation:
  Turn on the laptop and press F12 repeatedly
  When the start menu is shown recovery disc into the optical disc drive
  Press ENTER and follow the menu on the screen.

  If you will not be able to install the recovery image, it may be that the HARD drive is the troublemaker.
  Replacing the HARD drive is not a big deal, and you can exchange it only in just 10 minutes.