MCC problem

Similar Questions

• Mcc usb 1208FS for labview 10.0 connection problems

  I have version 10.0 of Labview installed on windows XP computer. I want to connect MCC USB 1208FS for Labview. Not able to see the device MCC in device of measurement and Automation Explorer interface. It appears? Please let me know the steps to access the device of the MCC in Labview.

  I can see the MCC card detected in the software InstalCal of MCC supported. I installed the latest version of the CMC the CMC site software.

  As far as I know, you will not be able to see physical computer as in MAX.

  From the file of help from MAX: "Measurement & Automation explore (MAX) allows to access your National
  Instruments of devices and systems. "that is material MCC is not a feature of National Instruments.

  Why not stick with the InstaCal software and the MCC screws provided?

  Ian

• VISA series and MCC USB-ERB24 compatibility problem

  Hello!

  I did have a lot of experience with the signals of digital I/o or VISA; However I have figure out how to control a shoot-syringe (Legato 270 - KD scientific) to help through VISA. I started having trouble when I plugged a USB ERB24 to control some taps at the same time.

  VI I trying to create needs to control the Director of the syringe, which is to remove or infuse to open and to close some hoses according to the direction of the syringe. The VI I wrote works fine until I have trigger a relay on the USB-ERB24, after that the syringe pushes unresponsive. When that happens, I have to unplug it, restart it and plug it back... then it works again. I suppose that for some reason, the USB-ERB24 is somehow interfere or cost overruns or something... but I don't know how or why...

  Here is the link for the drivers of syringe pump: LINK

  Also a link to the USB-ERB24: LINK

  I'm using Labview 2010 V10.0.1

  VI attached.

  I would appreciate any help/insight.

  Hello!

  You have activated the run culminating to see where and when you receive an error in the code? Looks like it is something hardware related, however. What is supposed to happen when you trigger a relay on the USB-ERB24?

  Thank you!

• Do not see the MCC - DRV module

  I read in another post where the solution has been to re - install DasyLab. I have done this and found a place in the Configurator where I can "activate" Measurement Computing (for my USB - 1608G) options. I have done that and restarted as requested. Now, I get an error when opening of DasyLab.

  Note: The error is when loading the MCCDRV_I.DLL.

  Help, please.

  OK, try to go the Configurator, uninstall the driver, MCC, and after the computer restarts, reinstall it.

  Then, after re-booting the computer again, run DASYLab.

  In any case, if you still have this problem, you should definitely contact computers Measurament.  It's definitely something they help you

• 1208fs for labview 10 usb connection problems

  Hello
  I'm relatively new to Labview and just improved labview 10. I used 6.1 before and had no problems using my mcc Board of 1208fs USB to run experiences before. I tried to connect even to labview 10 on my new computer, and the only thing that will connect to the instacal is. Ive plugged throu instacal, but is not visible in the list of I/O that selects the channel to use. Any help would be appreciated.

  Thank you!
  Andrew

  By the way, my os is windows xp

  Andrew,

  MCC daq devices have a different set of drivers for LabVIEW 8.2.1 LV versions and newer.  See http://www.mccdaq.com/daq-software/universal-library-extensions-lv.aspx this is ULx.

  I have one of the devices USB-1208 and discovered very recently this issue when I wanted to use it in a LV 8.5 application I wrote.  The new driver is actually nicer and DAQmx drivers a little resembles the way you use them.  While the former pilots of the Universal Library for older versions of LabVIEW looked like using traditional DAQ hardware drivers of OR.

• Problem with guarantee

  I didn't know where to post this put this on the forums, but it seemed like it should be.

  Bascially I have problems with the warranty I bought.  On the site it says that my warranty has expired.
  I have a problem with my laptop and cannot get it fixed until my warranty issue is resolved.

  I bought a new guarantee in August, unfortunately more than a hour on the phone with representatives of countless has been unfruitfull.

  The information on my debit card with some personal information are

  CHECK the CRD 08/27 HP PURCHASE DIRECT - SMB 800-888-0292 43xxxxXXXXXXXXX NOT 1632xxxxxxxxxxx? MCC = 5969

  Some research, I know that the charges came from HP SME Mediu.  The next number is my number credit card after the number starting with 1632 I don't know what it is for, but I hope it might be useful if it is provided to the right person. At this point I have not worked with

  bitofrustration, I saw your post and has forwarded to the right people for their review. You should hear from someone bit via private message on this Forum (Please note, as CherylG said, there may be a time to be contacted due to the end of week and holidays).

• M1000e with M610 Blade. iDRAC6 problems with the upgrade of the firmware 3.50 (Build 4) - "image downloaded missed the check" error

  I have the blade that is a M610. its current 3.30 iDRAC6 Firmware version (Build 17), his version of BIOS is 6.0.7. I am trying to upgrade the firmware to 3.50 iDRAC (Build 4). I am upradging by the MCC on the M1000e chassis. I choose the slot of in that the blade is and then start the IDRAC GUI. I choose firmware update and select the firming.imc file that I used successfully on some other M610 blades. After about 30 seconds, he returned with the following error.

  The uploaded image has no verification

  Why?

  I came across the same problem (with a refurb M610, iDRAC firmware has been 2.20).

  I tried to upgrade the iDRAC6 firmware to 3.60 via the web interface of iDRAC6 and it was a no go.

  I tried several browsers (chrome and firefox) and same problem each time.
  I tried to go to firmware (as shown in the accompanying note) 2.31 instead of 3.60 and same question every time.

  I finally managed to update the firmware of the iDRAC6 by upgrading the web interface M1000e and not in the iDRAC6 web interface.

  It worked the first time (using Chrome).

• Please help - need Urgent read MCC.

  First of all Hello.

  I developing a dialer application for the telecommunications company, that I work for, to easilly allow our users to call through our network (we sell cards call and the phone through a number of carrier selection which must be dialled before the destination). The problem is that I am in need to read the MCC code from the telephone network, the user is saved so that I can detect if the topic is on homelessness, and what country the user is currently in order to call the correct number to reach our switch and router properly, but also to load correctly.

  I tried to use getNetworkOperator() of TelephonyManager, but it returns an empty string. I also tried other methods to get the country (all TelephonyManager), nothing works.

  If anyone can help, I would be VERY grateful.

  Kind regards

  SK

  Hello

  Welcome to the forum!

  At the moment I can not test, but on Android devices, there is another method for the mcc and mnc news.

  Of your business, you can try the following calls:

  getResources () .getConfiguration () .mcc

  getResources () .getConfiguration () .mnc

• MCC and MNC network info tour

  Hello

  I stumbled upon a problem mcc weird & MNC anything other than they should be.

  I am located in Finland and running one unlocked Vodafone brand device. For some reason, the MCC I get is '580' that does not match any country. Anyone know if this is something that must be mapped to real CCM somehow, or is it just something wrong with the app?

  580 is a conversion, decimal number to hexadecimal. 580 d = 244 h, i.e. of Finland!

• Problem with the format SmsAddress

  Hi all

  I have a problem with SmsAddress according to the format string

  This code does not work:

  String addr = "0101234567";

  DatagramConnection dgConn;
  dgConn = (DatagramConnection) Connector.open ("sms: / /" + addr);
  SmsAddress smsAddress = new SmsAddress ("/ /" + addr);

  If I replace the address to:

  String addr = '+ 20101234567';

  This works.

  If I did not need to write the full address with country code, so how can avoid this problem.

  I found a solution for sms, country code, but I don't know if there's bettet solution or not.

  This solution is based on the International Mobile Subscriber Identity (IMSI) and the   Mobile Country Code (MCC).

  We can get the IMSI in the API of SIM (SIMCardInfo) then the first three bytes as the MCC.

  The I get the sms country code of the lookup table in the site:

  http://mobilecountrycodes.com/

  Note: You must remove the zeros before concatinating the code with local mobile phone number.

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• MacBook Pro display problem

  Hello members of the community.

  As of recently, I have noticed some glitches when feeding on my MacBook or awakened from his sleep.

  The colors are distorted, usually with pink, green, or yellow blobs. Blobs cannot entirely replace the colors, they appear to be contained in a element would normally be. For example. the menu bar will be partially pink and white, but pink does not leave the menu bar in this area, and the Office has green lines on it.

  I tried to take a screenshot, but the problem resolves in about 20 seconds, but it's a recurring problem.

  It happens when I wake up, connection or not. I had also certain powers serious and problems of performance, such that my MagSafe LED would not illuminate when plugged on rare occasions, fan could turn unnecessarily, graphics performance were SUPER slow, and the health of my battery was running out quickly. I actually ran a report on the system at 2 different times and my quality of full load is depleting of 1.2% per charge cycle, which is very worrying. I went from 6281 mAh mAh 6138 maximum capacity after two cycles of load. I'm tracking closely it because at this rate, my battery will survive only at load cycles about 150 instead of the 1000 expected, gives me the idea that this could very well be a bad battery. The computer is also warm to the touch while you sleep, not connected to the power supply. I NAP active but even taking into account should not be hotter my iPhone did the same thing.

  I have reset the SMC, and it solved a couple of problems. The charger works fine now and my performance improved considerably (which made me feel better, either it is a high-performance laptop, a 11-inch MacBook Air should not he surpass), and battery life has improved. I feel even if it uses a lot of power in his sleep. Maybe I need to turn off the NAP and see if that makes a difference. The graphic bug still persists however, and I don't have enough time to see if the max battery is depleting again.

  In regards to the bug, is there something that can be done? Basically, I want to assure you that I took all appropriate measures or if someone else has this problem to see if it can be software related instead of my computer.

  I have the entry level MacBook Pro with the retina, last generation.

  Any constructive contribution welcome!

  See you soon.

  -adreaux

  Hello bernardn753,

  After reviewing your post, it seems that you are having problems with the screen showing strange things on it. Looks like you already have a troubleshooting. I recommend you read this article, as reset NVRAM would be to reset your screen resolution settings that should help.

  How to reset the NVRAM on your Mac.

  Thank you for using communities of Apple Support. Good day.

• with IOS 10.0.2 - 5s iphone Bluetooth problems

  Since upgrading ISO 10.0.2 my M50 from PLT Plantronics (helmet unique headset) do not reliably connects with my iPhone 5 more. I have to go to the settings, activate bluetooth turned off/turned on, touch the device on the bluetooth page, etc. Once it connects successfully, it will reconnect (if I turn off the headset and turn it back on) for a short period. The next day he does not connect itself but I play with bluetooth on the iPhone again.

  It has always worked perfectly before the 10th of IOS.

  And, as I noticed others mentioning, the volume is much lower with IOS 10. The maximum volume is much lower. I can barely hear it now, more normal background noise, while driving.

  I did:

  Forget this device for the PLT M50 and paired again (several times)

  I did a Reset Network Settings

  I don't know what else to do - but it's a 10.0.2 IOS issue.

  Hello AppleUser2k,

  Please ask questions about your problems of connection between your iPhone and your Plantronics headset since you upgraded to iOS 10. I understand how important it is to have your Bluetooth devices connect with your iPhone with reliability. Here's what I recommend.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try the troubleshooting steps in this article to help: get help to connect a Bluetooth accessory with your iPhone, iPad or iPod touch device should also check with the manufacturer that the device has all the drivers and firmware to work with the new version of iOS.

  If you have checked everything and that you have installed the latest firmware or driver and always are problems, please be aware of your surroundings when you encounter these problems. If you can isolate the time or location, you see the problems, you can isolate the cause. You can even see this help article to ensure that you are not affected by outside interference: the potential sources of Wi-Fi and Bluetooth.

  Thanks again and have a great rest of your day.

• Problem after update 10.0.2 iOS iPhone touchscreen

  After I have updated to iOS 10.0.2, I noticed a problem with the touch screen. Using the position of the image on the right side, near the corner, the toushscreen does not work.
  For example: when you use the keyboard, I can't type the letter 'P', have trouble typing BACKSPACE. Using the Contacts app, I can't scroll through using the alphabet bar.

  Do what idea of the problem?

  Kind regards!

  Hi fabriciorela,

  Thanks for the upgrade to iOS 10! I understand that the right of your screen is unresponsive to the touch. You can try the steps in this link to fix the problem. If the screen of your iPhone, iPad or iPod touch does not respond to touch

  If it does not help the problem, try to restore the device to factory settings. I would like to backup your important data first.

  The backup of your iPhone, iPad and iPod touch

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

  Please use the Apple Support communities to post your question. Let us know how it turns out. Have a great day.