MCC and MNC network info tour

Similar Questions

• Cannot establish network connection. Messages on the icon alternate between "Acquiring network address" and "unplugged network cable.

  Original title: cannot establish a network connection

  Very well, a computer can connect to the internet. Another computer using the same modem cable and fixed connection of the router (for example using the port adapter, not wireless) Wireless does not connect. I suspect that there are has some settings somewhere that are not correct. Can you tell me how to understand where is the problem?

  Messages on the icon alternate between "Acquiring network address" and "unplugged network cable. When I run troubleshooting this is what I get:

  Diagnosis of IP Configuration
  Invalid IP address
  Info	Zero (0.0.0.0) detected IP address
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: reset the network connection
  action	Disabling the network card
  action	Activation of the card network
  Info	Successfully activated network adapter
  Info	Zero (0.0.0.0) detected IP address
  action	Repair Manual: Reboot modem
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  Info	Redirect the user to support call

  WinSock status
  Info	All base service provider entries are present in the Winsock Catalog.
  Info	Winsock Service providers strings are valid.
  Info	Entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.
  Info	Entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.
  Info	Entry provider RSVP UDP Service Provider managed the loopback communication test.
  Info	Entry provider RSVP TCP Service Provider passed the loopback communication test.
  Info	Connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter
  Network location detection
  Info		Using the Internet connection at home
  Identification of network adapter
  Info	Network connection: name = Local 2, Device network connection = Intel(r) 82562V-2 10/100 Network Connection, MediaType = LAN, type = LAN
  Info

  Ethernet connection selected

  State of the network adapter

  Info

  The network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn

  FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  warn

  FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  error

  Could not make an HTTP connection.

  error

  Could not make an HTTPS connection.

  error

  Could not make an FTP connection.

  I found the problem (s), even if I am always left with a few questions.

  During this process, I have disabled the firewall, but that did not help. However, I noticed 'tweaks' accessed via the tab 'Advanced' in 'Microsoft Firewall' which looked like, they must be checked in order to access the internet. I checked these and reintroduced the firewall. After I got things working, I unchecked them and things still worked so I obviously don't understand what these parameters.

  The solution:

  (1) I have to go straight from the modem cable to the computer. I can't have a cable modem, router wireless, computer, even if using hard wire, and even if this same configuration works with another computer. Also, I can't use a cable length to go from modem to the computer. So, it seems to have had a problem of cable length. Power problem? Only connected to this computer devices are the mouse, the keyboard and the Ethernet. Would not this be fixed with an upgrade of the power supply? Or is it due to the quality of the Ethernet hardware on the motherboard? It's a Dell Vostro 200.

  (2) in back and forth between configurations while following the problem, you must think to unplug the modem to reset between each configuration. You may have stumbled upon the solution, otherwise he's not shot. Also, I unplugged the cable from the modem when you reset data cable - do not know if it was necessary. I wanted to limit the degrees of freedom that I had a lot, as it was.

• Initial (and probably more common) question of Dr on SRM and private networks

  Hello

  Can anyone share best practices on the ground with regard to my question archiecture of network:

  According to the guide of the SRM administrator: Mrs. in protected sites and recovery must have access to the same private network (logic).

  We will have protected sites and located on the same ground but both recovery are far from each other on separate parts of the campus and there is network connectivity between sites.

  What are the different ways we can get two separate sites to share a private network?  What is the best practice?

  (1) fiber optic cables directly between sites using Layer 2 switches?  Any potential problem with switching over a distance?

  (2) with Layer 2 VPN MPLS? Enough to handle the traffic scenarios and failover/failback mature?

  (3) should work around SRM to allow a routed 3-layer solution?

  I'm from VMware

  As I said more simple solution is scalable layer 2 making available of VLANS / subnets in two sites in order to avoid the re-ip address of the recovered virtual machine. MPLS and direct DC of interconnection on fiber/xWDM were popular alternatives for the extension of the L2. As with anything there are advantages/disadvantages for things like network and mobile IP service (for example, routing, load balancing, etc.) of persistence or rigidity. The Cisco & VMware following white paper might be of interest that it focuses on a new DCI solution that introduces new options for VM environments. The paper is mainly centered around the Cisco Nexus product range and the ability to now support active/active balancing on various, redundant DC links:

  http://www.Cisco.com/en/us/solutions/collateral/ns340/ns517/ns224/ns836/white_paper_c11-557822.PDF

  You will notice the support of max distance of 200KM that is referenced in the document comes from the limits of support for the underlying storage replication (200KM for most synchronous suites), but there is also the effect of the reactivity of latency and VMotion application considerations. Site Selector Global (Cisco GSS) can be used for the traffic of a smart-balancing the load on the front-end server application as well as for unloading DNS service, DHCP and other common services - it would be more of a supplement to the core DC interconnect solutions mentioned above and not necessarily an exclusive alternative.

  Not sure what you mean by a workaround for Layer 3. SRM has the ability to re - ip of the VM during recovery, allowing you to change all THE info from the network stack inside the VM (network/gateway/dns servers ip/mask) and even generate scripts of ddns, but according to my post previous changing network info is in almost all cases, I worked with a customer "2nd choice".

• Thunderbird does not all files except "inbox." and against the info 'aid', there is NO 'account settings' under 'Tools' & I have the latest version of T.

  Thunderbird does not all files except "inbox." and against the info 'aid', there is NO 'account settings' under 'Tools' & I have the latest version of T. I just need to download the SENT MESSAGES, Inbox not only.

  Re: Where is 'account settings '.
  If you do not see 'Tools', then you do not have your active 'Menu Bar'.
  See picture below on the activation of all the toolbars make life easier.

  Different methods of location of the 'account settings ':
  Via the toolbar "Menu Bar":

  • Tools > accounts settings

  Through the pane of folders:

  • Right-click on the name of the e-mail account in the folders pane, and then select "settings".

  Via "Menu Icon.

  • Menu icon > Options > account settings

  Re: I need to download sent Messages Inbox not only.
  E-mail accounts IMAP see a remote view of the files on the server.
  You subscribe to view these folders in Thunderbird.
  You synchronize directories subscribed for a copy in Thunderbird.
  What you do in a folder for example imap: delete, will occur on the server, so viewing via webmail or Thunderbird folders appear identical.

  However, in your case, it seems that you have created a POP e-mail account.
  E-mail POP accounts can only connect to Inbox server and download server Inbox for the Thunderbird Inbox pop e-mail account.
  It's not a quirk of Thunderbird; This is how all Pop mail represents the work.

  There is a work around to get "sent" in the folder mail sent from server in Thunderbird. You just do it once, because when you send it through Thunderbird, it will put the e-mails in the folder sent TB pop mail account and not on the server.

  Thunderbird creates a "Sent" folder when first send you an email.
  So, if you have not yet sent an email, please send one, even if only to yourself.

  Then, move all inbox emails in the appropriate folders.
  You can create new folders to organize them.

  How to create a new folder:

  • Right-click on the name of the e-mail account, and then select "new folder."
  • Give an appropriate file name and click "create a folder".

  When the Inbox is empty:

  • Logon to the Web e-mail account by using a browser.
  • Move all emails "Sent" in the "Inbox".

  In thunderbird:

  • Click on 'Get the message'

  all the "Sent" emails must get downloaded from the server Inbox anto your Inbox in Thunderbird.

  • Then move all your emails in the 'Sent' Thunderbird folder.

  You should now have all these emails downloaded from the server and display in Thunderbird.

• HP Pavilion 15 laptop-p051us: bottle-necking and Brighthouse Networking...

  Greetings programs,

  I signed up for 35 G internet with Brighthouse lightning in August of last year. Worked great for two months, then started getting more slow slow and capped speed DL 12 G.

  BrightHouse over the last two weeks came out and replaced all the cables on the House, the street and poles near home. Replaced twice modem (Motorola, only an Arris, now a huge Ubee modem. Thinking it was my four year old and put DLink upgraded router to a Linksys AC1600 model +. I even spent two days and six hours on the phone with supervisiors to Brighthouse trying different things. Nobody seems to know what to do. When I bought this laptop that is Windows 8... and has been finally updated to 8.1.

  BUT...

  I'm still a bottle neck to 12g on the laptop... but devices ALL wireless, three tablets, three phones, PS3 (connected, but capped by Sony at 20G) etc. are the actual speed. ONLY my laptop is capped at 12 the wire or wireless... BUT when I got the service in August of 2014 all worked for two months. Laughing out loud.

  I have rand scans using malicious software Bytesand Microsoft Security Essentials to see NOTHING infect my laptop. I am at a loss now what to do.

  Need help...

  Hello @NeuroMan42,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post on how your laptop's Wi - Fi connection keeps dropping, and I'd be happy to help you in this case!

  To re - establish a coherent link between your laptop and the network, I recommend later in this document on troubleshooting wireless network and Internet (Windows 8). This should help to run a diagnostic on your system using the network and Internet troubleshooting, as well as measures to maintain your system over the wireless network.

  In addition, I suggest also follows the steps below to ensure that your power management settings do not interfere with

  the connection to the network:

  1. open DEVICE MANAGER
  2. open the NETWORK CARDS
  3. right click on the WiFi adapter for the pc and left click on PROPERTIES
  4. click on POWER up.
  5. remove the check mark beside : ALLOW the COMPUTER TO TURN THIS DEVICE SAVE START STOP
  6. click on OK
  7. close DEVICE MANAGER and test.

• I mistakenly remove updates from facebook and other networks, please how to restore it back

  Original title: error.

  I mistakenly remove updates from facebook and other networks, please how to restore it back

  I mistakenly remove updates from facebook and other networks, please how to restore it back

  Hello

  Use the following website links to Facebook help.

  Facebook Help Center | Facebook: http://www.facebook.com/help/

  Facebook Support Forums: http://www.thefacebookforum.net/forum

  Concerning

• I have Microsoft Money 2006 how can I update and keep the info?

  I have Microsoft Money 2006 how can I update and keep the info?

  Hi NRHand7,

  Microsoft has stopped selling money on June 30, 2009. The last activation of version (more Money, or money 2008) required in order to be fully functional.

  For more information, you can consult the following articles:

  What is Microsoft Money Plus sunset?

  Money Solution Center

  We can refer to the following articles and check if it helps.

  How to export and import account information in Microsoft Money

  How to remove and reinstall Microsoft Money

  You can also post your query in Microsoft Money Forum to get help.

  Microsoft Money

  Hope this information is useful.

• At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  original title: server and virus problem

  Hi SurajMendon,

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the platform of networking on TechNet. Please post your question in the TechNet Windows XP Networking forum.

  Networking platform

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads

• After I restarted the 2003 server, I get a message on two of my workstations the present on this computer and the network are different

  After you restart the Server 2003 due to a storm, I now get a message on two of my workstations that are different from the current time on this computer and the network

  Hello

  This question would fit better in Windows Server Instances.

• HP 15-r001nc: controller and USB network controller

  Hello. I reinstalled my OS to Windows 7 and I need the software for my laptop HP 15-r001nC: controller and USB network controller. Thank you

  Hi, I am in the process to recover my computer after losing the hard disk. Pavillion DV6 1030US. I installed a 500 GB SSHD and I'm having issues after using my original Vista SP2 64-bit software. In Device Manager, I have (?) in other devices. Following your disposal advise here is the information found in the hardware ID:

  PCI\VEN_8086 & DEV_4237 & SUBSYS_12118086 & REV_00

  PCI\VEN_8086 & DEV_4237 & SUSBSYS_12118086

  PCI\VEN_8086 & DEV4237 & CC_028000

  PCI\VEN_8086 & DEV4237 & CC_0280

• Lack of Volume and the network icon in the Notification area

  I lost my volume and internet icons in the notification area.  I'm going to the properties of the taskbar and put into service, and on the notification area tab, I only have the clock and checked power.  I can see the volume and the network listed, but they don't have a click box, then what to do?

  Try this

  1. Click Start

     Collapse this includes this image

     type regedit in the Search box and press ENTER.

     If you are prompted for an administrator password or for confirmation, type the password, or click allow.
  2. Locate and then click the following registry subkey:
     Settings\Software\Microsoft\Windows\CurrentVersion\TrayNotify HKEY_CURRENT_USER
  3. In the Details pane, click the IconStreams registry entry.
  4. On the Edit menu, click delete, and then click Yes.
  5. In the Details pane, click the PastIconsStream registry entry.
  6. On the Edit menu, click delete, and then click Yes.
  7. Exit Registry Editor.
  8. Restart the Explorer.exe process. To do this, follow these steps:
  9. Press CTRL + SHIFT + ESC.
  10. On the process in the Task Manager tab, click the process explorer.exe and then double click on end process .
  11. On the file menu, click new task (run), type Explorer and click OK.
  12. Exit Task Manager.

  http://support.Microsoft.com/default.aspx/KB/945011/en-us

• Loss of connection with my router, shows only limited access and my network showed that unidentified

  Original title: unidentified network, missing the default gateway

  Hello

  So one day out of the blue I lost connection with my router. I was able to reconnect but this time around I had only limited access and my network showed non-identified. I tried to connect to a different wireless network, same thing. When I run ipconfig, I'm missing a value for the default gateway.

  I tried to:

  -Reinstall the drivers for the adapter

  -update the drivers

  -Reset my router

  -Gateway ipv4 manually of entry

  -kill lan via Device Manager drivers

  -scream at the computer

  I have a Setup to dual boot with Linux Mint along side Windows 7. When I boot in Linux it connects to any network without problem.

  Some help would be appreciated.

  Plug

  Windows 7 Ultlimate

  I7-4700MQ @2.4

  GTX 765M 2 GB

  8 GB RAM

  1 TB + 240SSD

  Realtek RTL8188CE wireless

  Hello Alex,.

  Thank you for your response.

  I appreciate your time.

  I suggest you to uninstall the network driver wireless and reinstall in compatibility mode.

  To uninstall the driver, follow these steps:

  a. press Windows + R keys together, type devmgmt.msc in the run window and press ENTER.

  b. Click to expand network adapters, right-click on the map and click Uninstall.

  c. restart the computer.

  Now you can Download driver from this link wireless.
  Reference:
  http://downloads.Eurocom.com/support/drivers/zip/238/238_RealtekWLAN_W764.zip

  For reference:
  EC http://www.Eurocom.com/EC/drivers (238)

  To reinstall the driver in compatibility mode, follow these steps:

  a. right click the driver file, and then click Properties.

  b. click on the compatibility tab.

  c. click on check "run this program in compatibility mode for" and select Windows XP(Service pack 3).

  d. click apply and ok.

  Now, install the driver.

  Please keep us updated.

  Thank you

• Problem of password of account, without that we can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid.

  Hi, I hope you can help with this problem. A friend has 6 computers networked to a Tower Server and have a problem. A worker student put computers into hibernation, and since then, nobody can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid. I tried to get into the pc to try removing network and replace it, but I can't get on the Administrators account because it has been disabled. I'm at a loss on how to proceed. My friend cannot afford a service call, so I'll try to help him.  Thank you

  If the computer is on a domain then there are at least two accounts that can be used to remove the computer from the domain:

  • A domain administrator account.
  • A local administrator account.

  When your friend has launched Windows for the first time after buying the machine, he was prompted to enter the name of an account. This account is created automatically with administrator privileges. He should use it now.

• BlackBerry Smartphones, wifi and mobile network Q

  If I turn on my wifi at home & sign in, & at the same time, let Mobile network on... fresh data which of them will be run out of?  The Mobile network will win or share or just use wifi?

  Also I was wondering because I wonder if light work wifi when I'm at work, save my data & pass their lol

  TIA!

  Hello

  In general, BBs "prefer" WiFi network of business for services BIS data. You can always check inside the connection management > State of Services, which BIS route is average.

  But you should also check inside the apps... many 3rd party applications have configuration items, inside the application, allowing you to order the application to use a data compared to another channel. What I always do is run my apps use BIS... in this way, they will follow along as BIS shifts between WiFi and my network of business data. But, if (for example) you configure an application to use only your corporate data network, while the app can avoid past well after BIS BIS to WiFi, and this app may well continue to consume data out of your network connection data carrier, even if BIS moved to WiFi.

  With older OS levels, you had no choice, but to leave the "Data Services" set on "on" any channel to use, which often caused the situation described above (BIS on WiFi, but some consumption of carrier data app)... disabling the Services of data, these levels of older OS, BIS-level data for all channels off including WiFi. With the later levels of the operating system (somewhere in the OS7 range, I remember well), you can actually turn off the parameter Data Services and wireless leash... that allows BIS to still work on WiFi, but prevents any application using the data carrier network regardless of how the application is configured.

  But... I'm curious... you may have about the features that only work on SmartPhones BB, yet your profile on this site says you have only a PlayBook, in which case none of this applies since the PB has no radio has WiFi and mobile only. But, you posted this in the "BOLD" of this site section, so you could guess assumes that you have a "BOLD" in addition to your PB...

  Good luck!

• How to configure a multihomed in Windows 7, wired network and wireless networks at the same time?

  Hello

  I have a fixed computer Windows 7, I need to configure for the use of wire and wireless networks.

  On the phone we transfer vast amounts of data, astronomy cameras than only products of 20 to 30 seconds, space images 3-4 GB each. The cameras are connected to the top of a tower, which in turn is connected via a 45 feet cable CAT-5 to the search engine.

  Internet access requires a wireless network connection.

  These two connections work - separately. I have to disable an and activate the other to pass. This jump back and foth is obviously a bit inconvenient.

  How to configure Windows 7 to manage both types of networks at the same time? On another forum I learned this kind of configuration is called multihoming, and it's something difficult to achieve.

  Having studied more about it, there is another possible solution called Internet connection sharing. that may be easier. I haven't used this option for years (since the routers were introduced) but is still active.

  Disable DHCP on the Dovado or use a cable between the PC and the laptop.

  Turn on the wireless on the PC and make sure that you have an internet connection. Disable wireless on the laptop. Connect the PC's LAN ports and laptop (via router or a cable crossover).

  IN the network of PCs and next to the connections Sharing Center, you must have 2 Ethernet and WiFi options. Double click on WiFi, then on the next screen, click Properties.

  The second tab in the next screen is sharing, check allow other users of the network to connect and then OK.

  Define the IP addresses for PC and laptop as in my previous post, but this time on the laptop set the default gateway to the IP address of the Wired of the PC port, the 1st DNS to the address of the Huawei and value of secondary school who suggested for your ISP.

  This affects your PC to access wireless internet and allows the laptop to access the internet via the PC

  Basic information about ICS are HERE

  Manuals for the Dovado HERE