MD3000i (18JHQ4J) - optimal wide port becomes degraded

Similar Questions

• PIN.WID has become my default browser, I don't want to, can not uninstall and have no chance with "subject: config?"

  Ok. How can I get rid of the pin.wid as my default browser. When I click on firefox I get pin.wid. I can't uninstall it. I emailed them this question. Response (abbreviated); Subject: config in the address bar, I promise you, keyword.url in the search box... not stuck there... no results.

  There are a few different ways that a site could take over your home page. These include:

  (1) change your settings
  
  (2) an add-on
  
  (3) hijacking your shortcut of Firefox

  For #1, you probably already checked, but just in case:

  • Startup, homepage, tabs and download settings
  • How to set the home page

  You can use the home button or open a new window (Ctrl + n) to test the change.

  Note that malicious software can create a file that will pick up your settings at startup. This article describes how to find such a user.js file: How to fix preferences that will not save.

  For #2, try this:

  Disable all non-essential or unrecognized extensions on page modules. Either:

  • CTRL + SHIFT + a
  • Firefox orange (or the Tools menu) button > Add ons

  In the left column, click Extensions. Then, when in doubt, turn off.

  Typically, a link will appear above at least an extension disabled to restart Firefox. You can complete your work on the tab and click one of the links in the last step.

  For #3, if you get the unwanted page at startup and not when you use the home page icon or open a new window (Ctrl + n), check here: right click on your shortcut on the desktop for Firefox > properties > Shortcut tab. For 64-bit Windows, the goal should be the next, no more, no less:

  "C:\Program Files (x86)\Mozilla Firefox\firefox.exe"
  

  A little luck?

• Disorders of MD3000i controller

  Hello

  It seems that my MD3000i continues having controller problems. I get tons of critical errors via email notification, but whenever I'm in MDSM - status is optimal. The error messages I receive refer (for as far as I understand) on two controllers (enclosure 0, slot 0 and enclosure 0, slot 1). It means that both controllers have problems or that this means that a single controller continues to go down (restart) and fall back on the other controller? The errors are:

  -Optimal wide port becomes degraded (event 1706 error code)

  -Wide port degraded becomes impossible (1707)

  I would consider replacing a controller if I can confirm which of the two is a failure. Is there a way to determine which of the two controllers boredom?

  This MD3000i has now reached the end of his LIFE, and we have not supported more...

  Thank you, Alex.

  Hey, Alex.

  After a deeper look in this set, it seems that the raid at location 0 controller seeks to go south on you. You may prepare yourself to get another. We can check it out if you can get your cable from the console, plug it into this controller and capture the output via Putty.

  If you need the Putty settings and how to do this, let me know and I can send the instructions.

  BUT it seems that the controller 0 is continually being reset to the other controller. This usually means a replacement of the controller.

  Edit: I forgot to mention also that the disc into the slot in enclosure 0 10 is on its way. It would be good to replace this one.

  Wish I had better news for you.

• MD3000 slightly ill?

  Got the simple double node Windows Cluster that uses two controllers MD3000 as shared storage. Very stable, but I think that self-healing storage functions may be masking a hardware failure.

  Can someone explain more in detail log for me so I don't know what part to replace? Recovery guru says it all is fine, but a critical alert 1707 was sent to the monitoring software isn't all that happy.

  Can't see how to attach the file majoreventlog.txt so paste extracted from him...

  Description: Controller component tray has changed to optimal
  Specific event codes: 0/0/0
  Component type: fan
  Location of components: enclosure 0, slot 0

  Description: Controller component tray has changed to optimal
  Specific event codes: 0/0/0
  Component type: power supply/fan module
  Location of components: enclosure 0, slot 0

  Description: Map host or card switch successfully recovered
  Specific event codes: 0/0/0
  Component type: guest room

  Description: Controller delay verified replacement
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: at location 0 RAID Controller Module

  Description: Destination error driver
  Specific event codes: 0/0/0
  Component type: physical disk
  Location of components: None
  Recorded by: at location 0 RAID Controller Module

  Description: Destination error driver
  Specific event codes: 0/0/0
  Component type: physical disk
  Location of components: None
  Recorded by: at location 0 RAID Controller Module

  Description: The beginning of the day is over routine
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: Module to slot 1 RAID controller
  Recorded by: Module to slot 1 RAID controller

  Description: One or more other regions created
  Specific event codes: 0/0/0
  Component type: RAID Controller Module firmware
  Location of components: None
  Recorded by: Module to slot 1 RAID controller

  Description: Map host or card switch successfully recovered
  Specific event codes: 0/0/0
  Component type: guest room
  Location of components: None

  Description: The date started startup Routine
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: Module to slot 1 RAID controller
  Recorded by: Module to slot 1 RAID controller

  Description: All connections established through wide port
  Specific event codes: 0/0/0
  Type of component: component speaker (EMM GBIC/SFP, power supply and fan)

  Description: Unique connection previously established through wide port failure
  Specific event codes: 0/0/0
  Type of component: component speaker (EMM GBIC/SFP, power supply and fan)

  Description: Quiescence of stopped controller
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: at location 0 RAID Controller Module

  Description: Cache mirroring on controllers not synchronized
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: at location 0 RAID Controller Module

  Description: Destination error driver
  Specific event codes: 0/0/0
  Component type: physical disk
  Location of components: None
  Recorded by: at location 0 RAID Controller Module

  Description: Degraded wide Port becomes failure
  Specific event codes: 0/0/0
  Type of component: component speaker (EMM GBIC/SFP, power supply and fan)

  All of these events occurred between 01:03 and 01:05. Now is 01:21, so I go to bed hoping someone can post an explanation of how take care while I SLEEP. I can email the whole majoreventlog.txt the morning if needed.

  Thank you.

  Hello, Pondule.

  Honestly, from the surface, he looks and sounds like some simple firmware accumulated errors and an update can fix this. Usually, I see when there is "pilot destination error" and the location of the components is 'none '. BUT, I would like to take a deeper look and check that. I sent you an email and I'll wait for the bundle full support.

  Let me know if you have any questions. Impatience on your part.

• Help with ports BEFSR81 V2 has become inactive

  I have the BEFSR81 V2 and every day at least one of the ports become inactive and the router must be unplugged and plugged in again to reset the ports. In efforts to try to help this problem, I was going to upgrade firmware version 2.44.2 to that on the 2.45.10 site, but when he got download I get a consignment to the model error on upgrade end file. Can someone let me know what happens if there is a problem with the router ports go out or the update of the firmware will fix if all goes well this issue and how to get the firmware updated

  Thank you for the help

  Before trying to upgrade the firmware again, please reset the router by pressing button reset for 40 to 50 seconds long. This should help make the firmware upgrade a success. If it is not always works, try to upgrade the firmware using a tftp utility instead of the router interface based on user's web. The tftp utility can be downloaded from here. Please download and save the IRB on your computer. Once it is saved, run the .exe file. It will ask you the router's IP and password, and then select the file. Select the downloaded firmware file and see if it works.

• Port Ethernet on X61s

  The ethernet on the X61s port does not moored in the ban but only when the ban.

  Is this normal? If this is not the case, how do you get the port to work while in the ban?

  bhohenstein, welcome to the forum,

  It is normal that the ethernet port on the ban is a 'place', as the VGA port and modem port. The system can only support an ethernet port. When you fasten the ethernet on the ban become active port and internal ethernet port becomes disabled. Attach your cable ethernet to the ban and everything should work fine.

  Hope this helps

• Lack of Z - 400 serial port

  Hello

  I have a number of product Z-400 SG637UC #ABA

  Just updated to the latest version of the BIOS, was 1.17, I think.

  Manual maintenance and each user's guide I can find a reference to the serial port header (15-pin) construction which

  My motherboard has.

  However, I can't understand how to turn it on.  The security settings of the Bios do not list the serial port, and the Advanced Settings tab lists only the floppy drive and not the serial port.

  Are the parties other than the header not installed on the motherboard on this particular product number?

  Do not connect the pins of the rider 2 header and tell the BIOS the material is there?

  PIN 12 of the 15-pin header is labeled 'detect the com' on page 168 of the Z-400 maintenance manual.  I do not think it is a standard pins for communications series name.  Is it being stretched up or down to activate the port?

  I don't particularly want to spend money for the "2nd serial" material, when the first serial port is not working.

  Thanks for any help.

  PM

  AP_M,

  The Z400 has a 2 x 8 serial port header, you have found.  To access the serial port, one needs the HP, the PA716A Option kit serial port adapter.  This kit, described here, has a small PCB attached to a PCI card and cable to the PCB of the card mother Z400.  This PCB contains the RS232 serial port transceiver integrated circuit, so it is necessary to make the serial port work - a straight through cable from the motherboard to a will of connector serial port not working, to not try.

  Option kit that pa716a can be ordered as an option Z420.  The kit is not listed for the Z400, but the Z400 (and many other HP computers) use the same kit.

  To answer your technical questions:

  -IIRC, Windows requires masking devices that are not accessible.  That's why the serial port does not appear in the device without this option installed kit Manager.

  -12 axis, as you can imagine, is a "detect the com' which tells the system that the serial port kit is installed.  He is shot down (the Earth) when the cable attached to the motherboard.

  -If you want to experiment and see if the serial port becomes active, turn off the Z400, then put a jumper between the P52 12 serial port connector pin and ground.  Soil is on pins 8 and 7.  (The pins are numbered with strange pins on one side (row) and evens on the other kind of pin 2 pin 1 opposite.)  To determine which line is even or odd, pin 16 is the last pin and the missing key on the 'same' line).

  Then turn on the system.  After the Earth axis 12, the serial port should appear in the BIOS settings and certainly in the windows.

  * I think this is how it works, I have tried for a long time. **

  Does that answer your questions?

• E3000 resets occasionally wired port when connecting to the VPN PPTP using Windows 7.

  I've had an E3000 for a few months now and a couple of times per week that the router loses wired Ethernet connectivity while PPTP VPN connects via Windows 7. The router does not actually resets itself... but darkens light of wired connection, the computer establishing VPN, and connectivity to the router is lost. Within 30 to 45 seconds, the port becomes active, once more, and to establish the VPN connection. I've not seen this on a wireless connection, but I do not often, which may be why. Similarly, I have not seen this on my Vista or XP wired computers using the Windows VPN client... but then again I can't use them often enough to meet the problem.

  I see this mostly on my Windows 7 (x 64) SP1, it also appeared pre - SP1, development equipped PC IP6 disabled on the PPTP VPN. And I don't see that on the establishment of a connection... once the connection has been made I can be operational for hours (5/6 or more a day) with no issue.

  While this issue causes me all real headaches like this doesn't happen on the connection... I thought someone should know.

  abandoned,

  Gave to your suggestion to try, but did nothing to eliminate the problem. The router was already on the version the most recent but re-flashed in any case. I ran 3 days on an old Windows XP machine connected to a different port on the router, I had 3 days to do work, and I've never had the drop on the VPN port. But this morning back on my Windows 7 machine... the port fell during my first attempt... I then had no problem, the rest of the day. Despite her disconnect and reconnect a PPTP VPN a few times more. Go figure.

  Let's consider this resolved... as I don't want to lose too much everyones time hassling with something that seems to be minor. Thanks for the help!

• Request preventivo MD3000i disk HARD 600 GB 15 k ST3600057SS

  Ho need urgent di UN preventivo by 2 HDD da auswechseln sull'MD3000i (18JHQ4J) 600 GB 15 k ST3600057SS.

  Grazie

  Salve,

  the ho mandato una mail in privato.

  Grazie

• Ports of MDS9148 showing as a red x.

  I have 2 switches x MDS9148 which are mainly used for connections to the servers fibre, without, RecoverPoint devices, etc. I added three servers to ports 25, 26 & 27 but when I open the device GUI Manager, these ports are showing a red cross on the two switches. I ran a check of the license, and here is the result:

  See MYFIBRESWITCH250 # port - license
  Port available activation licenses are 0
  -----------------------------------------------
  Interface Cookie Activation License port
  -----------------------------------------------
  FC1/1 16777216 acquired
  FC1/2 16781312 acquired
  FC1/3 16785408 acquired
  FC1/4 16789504 acquired
  FC1/5 16793600 acquired
  FC1/6 16797696 acquired
  FC1/7 16801792 acquired
  FC1/8 16805888 acquired
  FC1/9 16809984 acquired
  FC1/10 16814080 acquired
  FC1/11 16818176 acquired
  FC1/12 16822272 acquired
  FC1/13 16826368 acquired
  FC1/14 16830464 acquired
  FC1/15 16834560 acquired
  FC1/16 16838656 acquired
  FC1/17 16842752 acquired
  FC1/18 16846848 acquired
  FC1/19 16850944 acquired
  FC1/20 16855040 acquired
  FC1/21 16859136 acquired
  FC1/22 16863232 acquired
  FC1/23 16867328 acquired
  FC1/24 16871424 acquired
  FC1/25 16875520 acquired
  FC1/26 16879616 acquired
  FC1/27 16883712 acquired
  FC1/28 16887808 acquired
  FC1/29 16891904 acquired
  FC1/30 16896000 acquired
  FC1/31 16900096 acquired
  FC1/32 16904192 acquired
  FC1/33 16908288 ineligible
  FC1/34 16912384 ineligible
  FC1/35 eligible 16916480
  FC1/36 eligible 16920576
  FC1/37 eligible 16924672
  FC1/38 eligible 16928768
  FC1/39 eligible 16932864
  FC1/40 eligible 16936960
  FC1/41 eligible 16941056
  FC1/42 eligible 16945152
  FC1/43 eligible 16949248
  FC1/44 eligible 16953344
  FC1/45 16957440 eligible
  FC1/46 eligible 16961536
  FC1/47 eligible 16965632
  FC1/48 eligible 16969728
  MYFIBRESWITCH250 #.

  In Device Manager, when I click on the Summary tab, it lists all the ports in the switch, but I only see 1 to 24 ports in the list.

  If I click on the port and click on configure, I see a configured Port VSAN, Mode: Admin = Auto, speed: Admin = Auto, status: Admin = Up, Oper is out of service, FailureCause is LinkFailure, but I had that they guys on the site plug & unplug cables fiber directly from server to pass but nothing has changed.

  I don't know why this is happening. Is there anything I can check why this is happening?

  Thus, it seems that the server may need that an operating system loaded with the proper drivers from CF before its ports become alive?

  Yes indeed!

• Live iSCSI SAN upgrade production network (Dell MD3000i and PowerConnect & ESXi 4)

  Hi all

  For the moment, I have a direct connection to my Dell MD3000i iSCSI SAN in ESXi 4 2 x host with no switch between the two, all of the virtual machine is within the SAN and running on both hosts.

  If I want to put a switch between the two and add one more iSCSI SAN so that the two SAN can be accessed / shared with the 3 ESXi 4 guests total, how should I approach the issue?

  any idea or guideline would be greatly appreciated.

  What I have to plan the time or can I change the old IP on the existing SAN iSCSI manually cable one by one without damage/alter the existing operation of the virtual machine on SAN? or I have to stop the virtual machine and then terminate the connection manually iSCSI session and then restart the host SAN?

  Thank you

  AWT

  Standard installation on the MD3000i is for a port iSCSI on each controller on a subnet and one on each controller to be on another.

  There have been people working successfully on a subnet, reported problems too.   I wish we were longer on our Vsphere upgrade, I'm not at a point but where I test things like Vmotion.

• HomeLab vSAN woes

  Hi all

  I had a few problems of vSAN where readers will show degraded when in reality they are very well confirmed by LSI controller and the condition of the equipment. Readers (SSD) seem to become degraded when I/O strike records (that is, create a virtual machine). All the guests have 2 x the tag as a SSD HARD drive with one of these SSDS. I wrote a post on this subject in March here which has screenshots and more details. Life has been very busy (my 17 month around hunting ) finally have time to continue to troubleshoot. It's all in the vSAN HCL await real SSD drives.

  
  

  The hardware specifications are:

  Hosts:
  

  Servers Supermicro (X9SCM-F) x 2:

  • CPU: 2 x Intel Xeon E3-1230v2 'Ivy Bridge'
  • Motherboard: 2 x Supermicro X9SCM-F
  • Raid controller: 2 x internal LSI SATA/SAS 9211 - 8i
  • Memory: 2 x Kingston 32 GB Kit DDR3 1600 MHz PC3
  • Records: 2 x Lexar Echo ZX 16 GB
    • SSD: 4 x Sandisk Ultra II 240 GB
  • Network cards:
    • 2 x HP DDR Infiniband HCA 20Gbps adapter ports
    • 2 x HP NC360T PCI - e Gigabit Dual Port card
  • Power supply: 2 x 400W Seasonic 80 Plus Platinum Fanless ATX12V/EPS12V

  Supermicro X10SAE-o:

  • CPU: Intel Xeon E3-1231 "Haswell"
  • Motherboard: Supermicro X10SAE-O
  • Raid controller: LSI internal SATA/SAS 9211 - 8i
  • Memory: Kingston 32 GB Kit DDR3 1600 MHz PC3
  • Disks:
    • Lexar Echo ZX 16GB
    • SSD: 2 x Sandisk Ultra II 240 GB
  • Network cards:
    • HCA DDR Infiniband Dual Port Adapter 20Gbps HP
    • HP NC360T double Port PCI - e Gigabit card
  • Power supply:
    • SS-520FL2 520W ATX12V / EPS12V 80 MORE PLATINUM

  Any help would be greatly appreciated.

  Thank you

  Dave

  Apologize for the delay. During the last two day, I've updated my homelab to vSphere 6 (thanks to EVALExperience) and am happy to report vSAN works beautifully on the 20 GB infiniband network. I could create and clone virtual machines and SSDS are not going in an unhealthy situation. Thanks to everyone for their comments and suggestions!

• Pavilion: laptop does not work well

  Since last year... my laptop does not work. Every day, new questions arise. I'm quite sad. The questions are the following:

  1. junk closing the system while working.

  2 Bluetooth does not work.

  3. system becomes too heated after 10 min.

  4. good quality becomes degraded.

  5 battery backup reduced day by day.

  Please help me...

  Hello, sorry to hear about your problem.

  This is the most likely cause of your problems: "3 system becomes too heated after 10 min."

  See the following article:

  http://support.HP.com/RS-en/document/c01657439

  See you soon

• HP Pavilion DV8 1200 eb Azerty

  Hello

  My HP Pavilion dv8 1200 eb began with an unknown device which I find for the webcam.

  On the list of the USB controller by system devices, the port is known as ""unknown device"

  "I several times uninstalled that USB port and after two or three restarts the webcam USB port become""unkn peripheral OE. error code 43.   Several times I followed the instructions provided by Microsoft, without any result.

  What can be done to fix this problem?

  Sincerely,

  JM2402

  Hi Futoji,

  For now again works the webcam?   I uninstalled the composite USB port where the webcam is attached using secure and restarted the computer.  The webcam worked again but I need to reinstall the drivers for ENE CIR Receiver because he did not have a sufficient sources.

  Let's see what brings the future.

  Jean-Marie,

• Get (5) different SAS errors for more than a year. Finally noticed after a disk RAID 1 is dead and the replacement drive will not ready. What is my controller?

  Just noticed newspapers Windows for my 6/iR PERC have been reporting these errors almost every day for a year, is my bad controller?  If Yes this is very unfortunate because it is integrated.

  1.) sense unexpected. SCSI sense data: Sense key: sense 3:11 qualifier detection code: 1: physical disk 0:0:0 controller 0, slot 0

  2.) SAS port report: SAS wide port 0 link lost on PHY 0. : controller 0 (SAS 6/iR integrated)

  3.) predictive Failure reported: physical disk 0:0:0 Controller 0, slot 0

  4.) (ERROR MORE RECURRING): a disk media error has been corrected. : virtual disk 0 (virtual disk 0) controller 0 (SAS 6/iR integrated)

  5.) \Device\RaidPort0, restore the device, has been published.

  Hello.

  In addition to the Windows logs, what is the status of the disk (VD) virtual and physical disk 0:0:0 in the BIOS of the controller or the OpenManage Server administrator? If the status of predictive failure is constantly reported, then you can consider replacing the physical disk 0:0:0. If the replaced disk is offline, try to force if online via the controller BIOS. Make sure that your BIOS and controller firmware is up-to-date.