MD3200 (SAS) Raid controllers and VLAN

Similar Questions

• get the question mark yellow by raid controllers and audio multimedia

  i ' am receives no sound media player

  Hi gerard 880,.
   
  -Remember to make changes to your computer once you have stopped receiving sounds?
   
  Download and install the latest drivers for the audio device from the manufacturer site to solve this problem.
   
  Device Manager displays a list of all devices that are installed on a Windows XP computer. When you view device information in Device Manager, you may see a device listed as unknown device next to a yellow question mark. It can be difficult to determine the cause of this unknown device, because there is little evidence that it generates.
   
  This article explains possible reasons that an unknown device may appear in Device Manager.
   
  How to troubleshoot unknown devices listed in Device Manager in Windows XP
   
  Additional reference on:
  Troubleshooting of conflict of devices with Device Manager

• RAID controllers

  Does anyone have a good link which explains the differences in Dell RAID controllers and accessories?

  For example.  The same controller works in the 2950 Dell R710 like?  How are the different cables?  Are batteries and cache different?

  In general try to understand what goes through one server to another in the Department to RAID Dell.

  Thank you

  All the info is here:

  http://www.Dell.com/learn/us/en/04/campaigns/Dell-RAID-controllers

  Although it isn't everything in a nice chart - you need to read all documents to get answers.

  Easier way? Ask here.

  CarterIT

  The same controller works in the 2950 Dell R710 like?  How are the different cables?  Are batteries and cache different?

  In general, the parts are designed to compliment the tech in the server, doesn't provide backward compatibility for older, less advanced hardware. The 2950 takes the PERC 5 / i, PERC 6 / i SAS 5/iR and SAS 6/IR. The R710 may take a PERC 6 / i and SAS 6/iR, but also uses the S300, H200 and H700 controllers.

  PERC 5 and 6 PERC use a SFF-8484 connector; the PERC H200 and H700 use a connector SFF-8087.

  Batteries must be the same, but the cache size and type are different (PERC 5/6 have 256 MB; H700 has 512 MB and 1 024 MB).

• If anyone has installed ESXi on an old post XW8400 and make use of the SAS RAID?

  So I dug up an old HP XW8400 Workstation, but it is missing some parts and I thought I'd see if anyone has this thing running with the SAS RAID, because most of the forums of discussion and problems seem to revolve around the SATA RAID. So is this still possible? I do not want to invest money and then have NOTHING to do...

  Well, you're lucky, because I had this question a long time ago, but I never thought that someone else would have taken the trouble but YES - it is supported - even if everybody out there seems to focus on the SATA RAID I took not stable worth, since I use SAS disks in my workstation , because they are MUCH faster and can support a flow MORE. I have ESXi 1483097 5.1 Build running with 2 450 GB SAS drives in a RAID 0 configuration, and the system just hums...

  It is an old machine, but I was surprised that he was able to follow with the latest versions of ESXi, that's why I don't bother throwing, so if someone is there looking into the purchase of a good workstation MARKET that supports ESXi 5.1 with dual Quad Core Xeon, 32 GB of RAM, and SAS RAID so you won't go wrong with this one. You will encounter a small problem though, but I guess I'll wait for others to try to run this configuration that I share this juicy tidbit, although it is relatively easy to overcome and all depends on how you run ESXi...

  I know if you tried and GB SAS...

• z820: looking for a software raid manage and view the status of disks hard raid

  HP z820 workstation,

  product # D3J63UT

  I'm looking for raid management software

  

  Thank you.

  I suggest that you follow the steps listed in the HP Document: "Z - series Workstation detection and fixing a hard drive failure within the RAID Controller utility" in the URL: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c04474148#N10829 you can find instructions how to enter each State type of RAID (Intel RST, 2308 LSI and LSI 9260-8i controller - It's the main RAID controllers usually associated with the HP Z820 workstation according to the particular configuration you ordered). Note that in most of the cases described in this document, you need to access the configuration of RAID controller during computer startup steps, by pressing CTRL + I (for Intel RST) or CTRL + C (for LSI 2308) or CTRL + H (by LSI 9260-8i). The installation program uses the RAID controller firmware and does not require to install complex inside Windows software, because it is done outside of the Windows operating system before starting. Find more details in "HP Z220 SFF, CMT Z220, Z420, Z620 and Z820 workstations maintenance and Service Guide" in the URL: http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c04205252-1.pdf , in the devices of annex b: Setup RAID (pp. 161-171) all types of RAID controllers that are relevant at the workplace Z820 are discussed.

• General on the raid controller and hardware

  Hello

  I have that the hard disk controller or controller raid (0,1,5) does not work on a computer, if I add hollow PCI slot a wil raid controller or hardware, computer, or the raid not works normally?

  Johan

  Hi Johan,.

  Thanks for posting on Microsoft Community Forums.

  Ideally it is dependent on the PCI slot you use, if the PCI slot supports the hard disk controllers and RAID controllers so it will work with the computer. Almost all modern PCI slots supports the hard disk controllers and RAID controllers.

  For more information on the operation of the devices and drivers on Windows 7, click on the link below.

  Windows 7: manage devices and drivers

  Feel free to write us if you have questions/queries when you work with Windows.

• Question about VMKernel iSCSI traffic and VLANS

  Hello

  This is a very fundamental question that I'm sure I know the answer too, but I want to ask him anyway just to reassure myself.  As a precursor to my question, the configuration of my ESX infrastructure is best described here: http://www.delltechcenter.com/page/VMware+ESX+4.0+and+PowerVault+MD3000i.  Or more precisely, we have two controllers MD3000i.  Each controller has two ports and each port is configured on two different subnets, with every subnet connected to the different switch.  ESX host are connected to two switches.  The only difference for the guide, is we have two MD3000i configured the same, connection to the same switches.  Each MD ports is configured on the same subnet, but different IP addresses.

  At present, we are in the process of upgrading our two iSCSI switches of humble Dlink DGS - 1224T to Cisco 2960 T of.  The switches have been and continue to be dedicated to iSCSI traffic, however, I'm trying to set up VLAN s on the side of the switch.  Originally, we used the default VLANS on switches, however, after you have added an another MD3000i, noted the Support Dell best practices is to separate each on its own subnet and VLAN MD3000i iSCSI traffic. This would result in iSCSI 4 VLANS, two on each switch and two for each MD3000i.  Firstly, is this in fact of good practices?

  Second, if I migrate preceding 4 iSCSI VLANS, as each switch port will actually be an access port, will there need to complete the VLAN ID field in the VMKernel configuration page? Presumably, this field is used when the tagging VLAN is used, but as our switches do not need any other rocking trunk (as they are dedicated to iSCSI traffic), there should be no need to fill?  I guess it would be prudent to keep the two existing subnets, create two new subnets and make changes to an MD3000i and connection of the ESX host.  Provided the switch and switch ports has been appropriate configured with VLAN on the right, the rest should be transparent and he wouldn't be Intel VLAN in all ESX hosts?

  Would be nice to get answers and thank you in advance!

  Gene

  (1) Yes, it is best practice for ESX iscsi, having an independent network and vlan for iscsi traffic.

  (2) No, there is no need to mention anything in the area of vlan, if you use an access port. Its a mandatory thing than a choice. If you supply the id vland with access port, it loses connectivity.

  Please explain a bit why you need to create two different virtual local networks for each MD3000i. You are going to use several on the same ESX box iscsi storage? Alternatively, you use only a single iscsi and use these 4 ports for the same single VMkernel interface?

  NUTZ

  VCP 3.5

  (Preparation for VCP 4)

• Reinstall the USB controllers and USB drives

  Some flash drives did not work properly. So I uninstalled my USB controllers and USB drives from Device Manager. When I tried to reinstall, the Add Hardware Wizard cannot find the drivers, now none of my USB ports work. Help, please...

  Hi Paul,.

  Please run the patch from this link and see if that helps.

  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/GP/hardware_device_problems/en-us?EntryPoint=lightbox

  For additional help, see:

  Advanced troubleshooting tips for General USB for Windows XP problems
  http://support.Microsoft.com/kb/310575

  If none of the suggestions above, you may need to reinstall your chipset drivers to fix the problem. Please visit the section of your chipset manufacturer support or your computer manufacturer's Web site for drivers.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• PowerConnect 5548 and VLAN

  Good afternoon!

  I'm looking to implement a 5548 in our existing infrastructure. I want to preface this by saying that I am very new to networking.

  I'm looking to have at least two VLANS separated.

  -The first vlan for public sites face. These will have static public IP addresses.

  -The second VLAN is iSCSI traffic. I would like that it won't face public.

  Is it possible to Setup or should I be looking for a different solution.

  If possible, how should I go about setting up?

  Thank you!

  The port that connects to your router should be placed in Trunk mode with the VLAN you want in the trunk port. All ports are in VLAN1 access mode by default, this means that the port that plugs into your routing device is in access mode for VLAN 1 and VLAN 1 has internet access. For traffic VLAN 2 to access routing equipment that you will need to change cela port in Trunk mode and adds 2 VLAN as a VLAN Tag.

  468-page guide details where to put labeling.

  See you soon

• Subinterfaces and VLAN

  Hi all

  I was hired on with a State... Now its been awhile, but I do not remember how subinterfaces and VLAN all link together!

  Now correct me where I'm wrong (please), but them VLAN is created on the correct first switches?  When you create a VLAN on a switch you don't need ip or gateway address by default because them VLANS are the switch.  If you want intervlan routing you need a router.  Then, you configure a port trunking between the switch and router (ISL, 802. 1 q).  Now in the router, you can create a VLAN, and here you inter the ip subnet or the default gateway addresses correct?  This is where I get confused as to what reasons do you need subinterfaces?  How they roped VLAN and what would be the logical flow of data?

  Anyhelp would be appreciated!

  Yes you are right. If you are using the layer 2 switch and want to make the intervlan Routing then you need Layer 3 router device. But you must configure the interfaces sub with the default gateway to route traffic. Because there is a single trunk between swich and router so we need sup interfaces for multiple VLANs.

  Interface FastEthernet0/0.1

  Encapsulation dot1q 10 (10 represent 10 ID VLAN)

  10.1.1.1 IP address 255.255.255.0

  If you use a layer 3 switch, then you point all sub interfaces need so then you can create the interface vlan with the default gateway. You must enable ip Routing.

  Interface vlan 10

  10.1.1.1 IP address 255.255.255.0

  Hope this will help.

  Please rate if this can help.

  Thank you

• VPN and VLAN

  We have a site divided into 2 IEE802.1Q VLAN, using no switches Cisco. They have a PIX515 for Internet access. It is also configured to provide inbound VPN access for management and general purpose of access.

  In principle it is possible to set up a new VPN connection which is reflected by its interior traffic be tagged with a specific VLAN ID while all other traffic (including other VPN connections) remain without a label?

  If the PIX ends your VPN from the outside that the answer is no. If the VPN is coming from outside, and ending at the PIX she never travels a VLAN. VLAN tagging is used to identify what VLAN came from a source image and what VLAN it is intended for a current switch vlan can 'route' frame through the appropriate VIRTUAL LAN. Why you want to tag from outside VPN traffic? If it's to control access, you can specify 2 VLANS and VLAN 3 on the PIX (as long as it has code 6.3) and control what VLAN, you want that each group VPN access to through the use of the ACL. Each VLAN on a PIX is treated as a physical interface. It has its own security prefs (0-100) and can have ACL applied to them as well as the physical interfaces.

• Create 2 VLAN (VLAN 1 and VLAN 2)

  Hi all

  I need help and advice with my new Cisco SF300-48. I want to create 2 vlan (vlan 1 and vlan 2). The switch is set at layer 2.

  example:

  VLAN 1 (port 1, 2, 3), vlan 2 (port 4, 5, 6)

  VLAN 1 can communicate with each other (port 1, 2, 3) and vlan 2 can communicate with each other (port 4, 5, 6)

  But vlan 1 cannot communicate with vlan 2.

  Any help would be appreciated

  Thank you

  Johan

  Well, as far as I understand the message communication between the VLAN is not necessary. The thing is, that all ports LAN VIRTUAL (for example VLAN 1 with ports 1, 2, and 3) cannot communicate with each other. Did you check the configuration of the port / VLAN (VLAN configured to each port configuration right / right about the tag-no identified)?

• Management and Vlan native in different subnet?

  Can I have a management ip and vlan native in a different on AIR-1242 switch subnet and 2960?

  Native on switch = 1.

  The interface vlan 100 = 10.10.1.25X 24

  BVI ip to the vlan 100 = 10.10.1.25X 24

  -HM-

  Hello

  As far as I know, the management and the native will be the same... I guess... You have Vlan native as 1 on the switch and Int Vlan 100 on routing switch? Am I wrong? Let me know what are your needs... which will help me to help out you!

  for your question...

  Normally, we specify him vlan native on the switch and the AP so that communication happens... communication won't happen if there is a match of...

  Looking forward to hear from you!

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• With the help of VLANS and VLAN Tagging is not working / no connection

  Hello

  I m trying to configure a VLAN between some virtual machines on ESX host 3.

  I want to do this way:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1004074

  I got 1 dedicated NETWORK adapter to each ESX host that is connected to a dvSwitch in which I configured a portgroup

  with VLAN ID 2121. I have configured each virtual machine to use this network.

  When I put the virtual machines on a single host, they are able to communicate.

  When they are placed on different hosts they are (if the VIRTUAL LAN is enabled on portgroup) not able to communicate.

  So I m assuming it must be a problem in the config NIC on the ESX host or switch.

  I m using a HP2910AL on which I activated mode trunk for each port that is connected to a NETWORK card with

  the dvSwitch/Portgroup I try to use for the vlan. In the hp switch, I have a default VLAN with ID 1 where

  the Ports are marked not signposted. I install a second VLAN on the switch with ID 2121 in which I scored

  This tag ports.

  Is there something else to do - perhaps side ESX host?

  I tried changing the settings as "forged transmission-> allow ' on portgroup and I found other things

  in the web, but always without success.

  Kind regards

  Patrick

  Were you referred to this guide? :

  http://CDN.ProCurve.com/training/manuals/2910-ATG-Feb09-2-VLAN.PDF

  "show vlan ports" would be my next check to make sure that you have connected to your ESXi host 3 ports in the vlan 2121.

  As Duncan has said if you have a VLAN ID on the portgroup in the vSwitch and you have the port on the pSwitch as trunk not acess and VLAN ID is allowed on the trunk port pSwitch you should be ok.  Just to clarify the trunk is 802. 1 q No 802.3ad.

  The reverse is not VLAN ID on the portgroup vSwitch, use coelio on pSwitch with VLAN ID.  Limited pSwitch port to a VLAN, this may be ok for you?

• I would like to migrate from Aperture. What happens to my masters that are on a RAID array and then what should I do with my safe which is located on a separate drive please?

  I'm sorry, but I'm loud understand what happening to my master original RAW files, I keep offline on a RAID array and then what I do with my safe that, like all my photos modified? Sorry for this simple question, but would someone help please my lift the fog?

  Thank you

  Rob

  One of the major downfalls of Aperture is that it shows you where are your pictures. They always favored it as a feature (even as a ' new paradigm'), but it's not so wonderful when you need to do something about Apple never intended. Then, it sounds really like it led to you not knowing where your files or files that correspond to which elements of the UI opening. I suggest that you need to nail for yourself - images from Aperture to right click and choose Show in Finder, until you know where everything is.

  Otherwise, make sure you have plenty of available disk space, stop asking questions and just see what happens when you run plugin import LR with the options I suggested. It won't damage the opening.