MD3220 and hyper-v CSV

Similar Questions

• Ping issues - Windows 2008 R2 and Hyper v2008

  Hello

  I'm looking for a few windows networking procedure of experts here to solve these 2 problems.

  I'm very good in Linux but not in windows, networks than some basics on windows of course.

  I installed Windows 2008 R2 and Hyper-v 2008 on two machines different level of "WORKING group" because I'm small laboratory

  I done the settting up the ip addresses static, of the hostname (s) on those computers.

  Windows 2008 R2 => 192.168.1.60 - obiee

  Hyper-v 2008 => 192.168.1.61 - hyperv2008

  I have DNS running on 192.168.1.10 server and my linux local dns host: narayana.local

  I can ping linux boxes ping, ping hyperv2008 obiee hostnames - works perfectly

  I have a few problems in the windows operating system

  (1) i cannot set my computer full qualified domain name say obiee.narayana.local, hyperv2008.narayana.local - it can be a low priority

  (2) i don't can't ping using host names of these 2 machines - priority issue, I get a message

  C:\Users\Administrators > ping hyperv2008

  Ping request could not find the hyperv2008 of the host. Please check the name and try again

  = I can ping IP_address - works perfectly =

  (3) in view of these questions I can't control my hyper-v to obiee machine.

  Waiting for your early resolution

  Ask in the forum Windows Server:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• 5.1 ESXi does not see any number of logical unit after restarting both MD3220 and R820

  We restarted our host R820 ESXi 5.1 and table connected to SAS MD3220.  After the reboot, the HBA on ESXi shows no device.  We turned on the MD3220.  WAITED 5 minutes before feeding the R820.

  FYI... the complete Setup includes two R820 connected to two MD3220 through SAS.  The two R820 cannot see all devices on two HBAs after reboot.  We have redundant RAID controllers on the MD3220s and redundant HBA on the R820s.

  On the MD3220, the status of host interface ports appears.

  Anyone know this problem?

  We found the problem.  On the MD3220s, we noticed some "unidentified host identifiers.  For a reason unknown to us, the host port identifiers changed after turning power off and power on all R820s and MD3220s.  To resolve this problem, we replaced the identifiers.  It seems that someone swapped the SAS cables.  I don't think that someone made.

• What is the difference between containers and hyper-v server windows?

  Hello

  What is the difference between containers and hyper-v server windows?

  Thank you

  http://windowsitpro.com/Windows-Server-2016/differences-between-Windows-containers-and-hyper-v-containers-Windows-Server-201

  PS: Where's your homework due?

• VMware Workstation and Hyper-V are not compatible. Remove the Hyper-V system role before running VMware Workstation

  Ouch. I just started to do some Win Phone 8 and development Win, and all simulators are needed for development.

  This means that a dev to Win8 may only work on their host... I'm sure it would work in a virtual machine.

  Can I make for happy? (Hyper V might have to win here... sigh).

  VMware Workstation and Hyper-V are not compatible. Remove the Hyper-V system role before running VMware Workstation

  Once you install the Hyper-V role on your host, your host is no longer running Windows 8 as the native operating system.  It runs Hyper-V as the native operating system, and Windows 8 runs as OS management within a privileged under Hyper-V VM.  With the Hyper-V role installed, * everything * runs in a virtual machine under Hyper-V.

  So to run a virtual machine under my computer in Windows 8 under Hyper-V, you must be able to run a nested VM.  It's possible with Hyper-V, the hypervisor host, but with the updates in custody, I mentioned above.

• script to get the csv vm disk usage and export to csv format

  Hi all

  I am trying to create a script to get the use of disk for vm - space - free space and total disk space.

  I used this script that allows me to get the required result.

  but I need to edit the script for each cluster, VM he should get computers virtual cluster and check the vm disuage. and export of csv file

  $vms = import-CSV "C:\Cluster.csv".

  $outputfile = "c:\Diskusage.csv".

  SE connect-viserver VC-vcadmin username-password

  {foreach ($vm to $vms)

  Get - VM $vm.name | Where {$_.} PowerState - eq "Receptor"} | Get-VMGuest | Select the ExpandProperty - VMName disks | Select VMName, path, @{Name = "DiskCapacityGB"; Expression = {[math]: Round ((($_.))} {{((Ability) / 1 GB), 2)}}, @{Name = "DiskUsedMB"; Expression = {[math]: Round ((($_.))} Capacity - $_. {{((FreeSpace) / 1 MB), 2)}}, @{Name = "DiskFreeMB"; Expression = {[math]: Round ((($_.))} {{((FreeSpace) / 1 MB), 2)}} | Export-Csv - NoTypeInformation $outputfile}

  Viserver disconnect

  Joint the output file

  Veuileez help me in creating the script

  You can try like this?

  Connect-viserver VC -user vcadmin -password
  foreach($cluster in Get-CLuster){
      $outputfile = "c:\" + $cluster.Name + "-Diskusage.csv"    Get-VM -Location $cluster |
      Where { $_.PowerState -eq "PoweredOn" } |
      Get-VMGuest |
      Select VMName -ExpandProperty Disks |
      Select VMName, Path,
          @{Name="DiskCapacityGB";Expression={[math]::Round((($_.Capacity)/1GB),2)}},
          @{Name="DiskUsedMB";Expression={[math]::Round((($_.Capacity - $_.FreeSpace)/1MB),2)}},
          @{Name="DiskFreeMB";Expression={[math]::Round((($_.FreeSpace)/1MB),2)}} |
      Export-Csv -NoTypeInformation $outputfile}
  
  Disconnect-viserver
  

  The script creates a CSV file for each cluster.

• Comparison between ESX 4, Xen and Hyper-V

  Hello!

  Someone at - it a (new) comparison between ESX 4, Xen and Hyper V? Management performance, stability, cost and so on.

  Thank you to

  Hello

  Visit this link for the last comparison http://www.it20.info/misc/virtualizationscomparison.htm

  http://ctistrategy.com/2009/08/18/VMware-vSphere-Microsoft-HyperV-whitepaper/

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!

  Prakash

• Core i7 - both vmware and hyper V not running any X 64 Machine virtual (X 32 VM Client works on vmware Xp/vista) built on Windows Server 2008 X 64 basic

  The vmware and hyper V not running any X 64 Machine virtual (X 32 VM Client works on vmware Xp/vista) built on Windows Server 2008 X 64 Basic.

  Windows (pre install UI) error code install (0xc000035a) that the processor does not support X 64 Mode

  Any of that with core i7 system any help would be much appreciated, thanks

  -Software VMware Server 2.0.0 122956 - OR - VMware Workstation 6.5.1 126130 - OR- Microsoft Hyper V

  -Tried - BONE at BASE of MATERIAL AND the VM ENVIRONMENT

  X 64 Windows Server 2008 6001 - OR - X 64 Windows Server 2008 6002 - OR - X 64 Server Windows 7 6801

  System - Core i7 920 + X 58 (GA-EX58-UD5) + 6 GB DDR3 + OCZ SSD

  Intel Core i7 920 Webpage - http://www.intel.com/products/processor_number/chart/corei7.htm

  Gigabyte GA-EX58-UD5 - latest version of the Bios F3

  Web page - http://www.gigabyte.com.tw/Products/Motherboard/Products_Spec.aspx?ClassValue=Motherboard & ProductID = 2958 & ProductName = GA-EX58-UD5

  Advanced features of MB Bios CPU - tried Both ON and OFF

  Hyper Threading - Threading 4 AND 8

  Intel Virtualization - ENABLE AND DISABLE

  Looked in the VM Bios as well

  6 GB DDR3 3X2GB 1600

  Please, see troubleshooting problems of Intel VT - x.

  Also note that you can not the role Hyper-V installed in the parent partition, if you want to run the VMware using VT products, as Hyper-V virtualizes the parent partition, but it only virtualizes the VT CPU features.

• The Group PS6100XS and Hyper-V Server 2012: migration of storage between LUNS corrupts VM

  Well, I'm puzzled! Summer hit my head against this whole week. Basically, ranging from a virtual machine clustered LUN on the Bay EqualLogic corrupts the virtual machine. Here is my configuration:

  1. SAN 1: PS6100XS 6.0.1 firmware, 2 LUNS configured as CSV, 1 as a quorum disk
  2. SAN 2: FreeNAS 8.3.0, 2 LUN (ZFS-formatted, for what it's worth)
  3. Server 1: Dell R310 running Windows Server 2012 with Hyper-V installed feature. 4 network cards: 2 made team for traffic LAN, 2 for iSCSI with HIT KIT 4.5 configured for MPIO.
  4. Server 2: Old box SuperMicro running Windows Server 2012 with Hyper-V feature installed. 2 network cards: 1 for LAN traffic, 1 for iSCSI with HIT KIT 4.5 installed
  5. Created and all cluster validation tests passed
  Here's what works:
  1. Ranging from a virtual machine of the LUN if there is no activity on the VHDX
  2. Move a VM all LUN the EqualLogic to any number of unit logic FreeNAS or vice versa
  3. Move a VM between LUNS on the FreeNAS
  4. Move a VM between LUNS on the EqualLogic BEFORE I created the cluster (just using Hyper-V Manager, not the Failover Cluster Manager)

  This is what kills the VM whenever:

  1. Create a virtual machine through the Failover Cluster Manager - is not matter which node owns the storage or the VM - tried all combinations
  2. Take an active virtual machine, power and move a LUN EqualLogic to another EqualLogic LUN. The move signals the success, but the VM blue screen at the end of the move will and will no longer be able to start. It's basically fried.

  BTW, I tried also to disable one of the iSCSI NIC on the R310 - what does not help either. Any ideas? I have a case goes with the support of Dell EqualLogic, but so far they have been puzzled. Anyone got something like this works yet?

  OK, after Dell tried about 5 different times to tell me that my setup was not supported (actually claimed that EPA software was not supported!) I finally got someone who gave me workaround: disabling ODX by changing the key "reg" HKLM\SYSTEM\CurrentControlSet\Control\FileSystem\FilterSupportedFeaturesMode from 0 to 1. This "fix", but it also takes one of the most interesting features of the 2012 Server + EqualLogic: ODX! With active ODX, I can move 20 GB in< 1="" sec.="" with="" it="" disabled,="" it="" takes="" around="" 2="" minutes,="" depending="" on="" network="">

• Error 1074135030 and hyper-Terminal failure while communicating with the power supply

  Hello

  I use the serial port to communicate with power XG XG 8-100 (series) by Xantrex (Sorensen).

  I could not find the driver in IDNE, but I found one on the site of the company that is http://www.programmablepower.com/products/XTR/XTR_Downloads.htm , when I run the example that I get the below error:

  Error 1074135030 has occurred to be initialized with Options.vi of DC850W

  Driver status: (Hex 0xBFFA000A) check that the name of the library (C:\DC850W\DC850W_32.dll) and (DC850W) prefix are correct.

  I don't know what the problem is with the name of the library that makes such a problem.

  FYI, I tried to communicate with the device using the hyper terminal, but there is no answer. When I check the MAX, it seems that everything is OK, that the State is: the device works properly!

  Do you have any suggestions for me?

  Any help or suggestions appreciated because I'm messed up with this and I don't know how to go further.

  ELA

  
  

• MS win Server R2 2012 and Hyper-V issue licenses

  My company has 60 employees (and 60 desktops / laptops) and currently have an old principle that server solution of Microsoft Basic with element a cloud as Office 365 for email only. We seek to reduce the estate of server to Server (2 CPU - Dell PowerEdge T610), it currently runs on two old but not sterilized systems running Windows Server 2003 R2 (Dell PowerEdge 2900) and Windows Server 2008 R2 (Dell PowerEdge T610).

  In the short term, we want to create a brand new installation of MS Windows Server R2 Standard edition 2012 who will manage our advertising (and DC) and support businesses main accounting IRIS software that requires a MS SQL DB. This cloud all must be configured to allow integration with MS Azure Site recovery to allow us to turn up in the azure of the VM disaster. In my view, this means that the configuration of the OS as a Hyper-V virtual machine instance.

  The new server Win 2012 R2 has not really be a VM as its only one instance that I need, but from what I can make out, I need to make a virtual of Hyper-V machine to join the recovery Site of France. I can't determine exactly what license I need to achieve however. Any help would be appreciated.

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Cluster Hyper-V CSV allocation unit size

  Hello. Is there any recommendation Dell when it comes to the size of the allocation unit of the NTFS volumes that serve as CSVs (Cluster shared Volumes) in a Hyper-V cluster?

  Using EQL LUN in the background apparently.

  Where should we go with the default using Windows (based on the size of the volume/LUN) or should I use something different to optimize performance, for example 64 k?

  CSV store virtual machines with different workloads, nothing specific, such as SQL pure or web servers, etc..

  Thanks in advance.

  Hello

  Cluster size when you format a volume must always be 64K.   Which corresponds to the size on the spreadsheet.  Writing in complete stripes is the most effective way, it reduces the overhead of RAID.

  Kind regards

  Don

• PS 6100 and Hyper-V

  Just set up my server EQL 6100 and r.620 (Windows Serer 2012 R2 Datacenter). I have Hyper-V configuration in the past, it will be the first on an EQL. It is a nonclustered environment. A server and an EQL. In the future (later this year), we will make another server in front to HA. The EQL occupies Raid 10.

  My questions are the following:

  1. for best practices, can we establish individual volumes for each virtual computer? Then put each VHD on the volume?

  2. is there any way to get around the limit of 2 TB for a volume?

  3. I plan give SQL its own volume. If I give SQL its volume (for example 1 to, that we're going to put a data warehouse on here), should I simply perform a default installation or should one make a smaller volume (80 GB) for the SQL o/s and join a D: (another volume, say 900 GB) for SQL?

  I would like to hear how others have configuration and successes or failures.

  Thanks for your time!

  You select the host NIC that guests can use for iSCSI Yes. This should be a different NIC what the host uses for iSCSI.

  If you need at least 4 NICs (NETWORK ports) network for iSCSI; 2 for the host and 2 for the guest (s).

• MD3220 and two 1220 shelves (SAS) - software of Multipathing R2 2012 Windows?

  Is there any software and multipathing drivers supported for Windows 2012 R2 and a MD3220?  I don't see any software on the support site.

  If not, what is the recommended route to connect up to 4 of the r.620?  This is an installation of SAS das.  I use the native MPIO feature in Windows?

  Let the ISO/DVD autorun and install at least the host software. This installs the minimum requirement for the guests that will be connected to a network of SAN MD3k (agent, MPIO software, etc.). If you also want the graphic management interface, you can opt to install that as well. Note that the host software will require a restart of the physical server to the end.

• Md3220 and md1220 combo, how to configure any global hot spare parts.

  The MD3220 is full of 300 GB 15K SAS drives the MD1220 is full 1 TB NL 'SAS' 7.2 K disks. The two boxes have discs 22 & 23 unused in the goal is relief. However all the mechanisms that I use to create hot household simply attaches all four disks to two speakers. I'd rather have two spare drives only protect readers in their own enclosure. Interestingly enough, I asked the software dell 'automatic configuration' (sic) the hot spare and he decided ONLY two use 1 TB drives and use them to protect the two speakers. In addition, I was quite puzzled as to why he also allowed me to do it manually the absurd configuration to allow a 300 GB drive protect a forum composed of 24 1 TB disks. In any case, is it possible to have host associated with a case (or disk group) spare parts. ? Thank you.

  You can't dedicate a hot spare in a picture of MD3k-series. If a hot spare will succeed for any player in any long case that the size of the spare drive is the same or larger than the failed drive.