Merge devices with multiple network interfaces

Similar Questions

• TCP on PC server with the network interface has 2

  If I need to create a TCP on PC server with the network interface has 2 with a different IP address, for example 192... and 172... and the IP address of the client side is 192..., is there something I need to take care.

  Any suggestion, thank you.

  No, by default the server listens on all interfaces.

• 4235 with multiple monitoring Interfaces?

  This is a general question as to whether anyone is running on 4.0 4235 sensor code with multiple monitoring interfaces?

  Basically, I wonder if you have any comments on the performance or if you run into any problems with the configuration. I have not seen too much documentation for configuration in fact this, so I wonder if there are additional requirements or considerations.

  Hi Chad,

  With ID 4.0, you can only montior using an interface to sniff. 4.1 you will have taken care of multiple monitoring interfaces.

  As far as performance goes, I don't see any problems and more to ensure that the management station is able to handle the upcoming alarms when using several interfaces.

  Thank you

  Obaid.

• How to configure a VM with multiple network cards to see Agent?

  How to configure a VM with multiple network cards to see Agent?

  We can archive this requirement by configuring the subnet used view Agent.

  The subnet determines which view address of Network Agent provides the server instance to connect to view for the client protocol connections. The view on VM officer has more than one NIC

  Follow the procedure below:

  on a display Agent installed VM,

  * Recording of VM session.

  * RUN--> type regedit or type regedit.exe at the command prompt

  * Create a registry entry to configure the subnet.

  For example: is HKLM\Software\VMware, Inc. \VMware VDM\Node Manager\subnet = n.n.n.n/m type - REG_SZ.

  In this example, n.n.n.n is the TCP/IP subnet, and m is the number of bits in the subnet mask.

• VMware device with 2 network cards claiming the same IP address with two MAC addresses

  Hello.

  I see messages intermittent my gateway network two MAC addresses associated with a virtual machine running on a 5.5 ESXi host for the same IP address.

  The virtual machine is a MiTel 3300 controller for a VOIP system. the system is configured with two IP addresses, one on the local network and another with a public IP address in the DMZ. In the network configuration of the 3300, I assigned the address LAN IP at 00: 0C: 29:30:B2:B2 and the DMZ IP at 00: 0C: 29:30:B2:BC (Mac for network devices presented by the ESXi host virtual machine).

  On the host, I configured a vSwitch with exclusive access to two physical network adapters on the host machine. The vSwitch is configured with two machine virtual port groups, LAN and DMZ, with access to the physical network interface cards. Tab grouping of groups vSwitch port NIC, I replaced the order of failover of the switch to activate an active NETWORK card only for the Group of LAN ports and the other card NETWORK only for the DMZ port group. (I don't know how the content of the column of networks is determined. Neither is correct for the traffic on the physical switch. If these are configurable, please advise and I'll change the settings). The relevant parameters of vSwitch, groups of ports and VM are distinguished below.

  On the virtual machine itself, through the VMWare host, I assigned 00: 0C: 29:30:B2:B2 for the Group of LAN ports and 00: 0C: 29:30:B2:BC to the DMZ group port (best I can tell, anyway, since the MAC address field annoyingly obscures the last two digits of the MAC address - break if I invert the mapping) (, but all seems OK).

  The goal here is to make sure that MACs of ports vSwitch the 3300 is listening and sending always correspond to the physical ports that are VLAN Tag by the physical switch to ensure the routing. Generally speaking, it seems that what is happening but, intermittently, we cross one-way calls that suggests a problem of routing between us and our SIP trunk provider; coinciding with these incidents, I get an email along the lines of "the security in the network device has detected a conflict of IP address with two or more devices. The period of INVESTIGATION "DMZ. DMZ. DMZ. DMZ' is claimed by the following clients with MAC addresses: ' 00: 0C: 29:30:B2:B2' ' 00: 0C: 29:30:B2:BC'. »

  I did something in the configuration that would lead to this kind of collision intermittent? Have a hacked together a way to do something that could be accomplished in a way that is simpler and more reliable?

  Thanks for any idea that you can offer.

  Kind regards

  J.

  

  

  

  I probably don't fully understand your configuration, but it seems that you are not interested in using the collection of NETWORK adapters in the virtual switch of the VM MiTel 3300.

  If it is correct, why not create two virtual switches, each with a group of port (LAN and DMZ) unique and with a separate connection of (vmnic2 and vmnic1)?

  In general, collection of NETWORK adapters may be used to share traffic between uplinks and ensure that if one of the uplinks connect fails, a virtual machine still has access to the network.

• BlackBerry smartphones register the device with another network

  Hello world!

  I have a huge problem with my Bb I bought the camera in an Orange shop in the United Kingdom and before leaving the country, I've unlocked it so that I could use an Italian SIM card. Now I'm in Italy and the problem is that I can't save with the network here and so I can't set up the e-mail account or use any other internet application. My new carrier (TIM) cannot help me. Is there something I can do? Please help me!

  Yes, you must contact Orange and have them remove your device PIN of their network.

• Server with multiple network cards

  Hello

  I have a server with multi-port NETWORK adapter running ESXi 5.5.0

  Can anyone remind me how to allocate a VM to port a network?

  or point me to the URL of the full help?

  Thank you all

  The c# Client is that you need to install on your windows computer. The alternative would be the Web Client vSphere. Both are essentially 'vSphere customers. "

  Anyway, you don't need to restart. You can change the network as you want without having to reboot.

• A physical server with 2 NETWORK interface card using a virtual machine as IPS (transparent VM) and everything should work normally?

  Hello guys.

  Is there a diagram that I made, using for my self this question.

  

  As you can see, I have a physical server with 2 NIC I don't want to use a VM (with Snort) as IPS / IDS system for inbound traffic on the management of VLANS. Is it possible to use this VM in this way (as an IPS/IDS, VM with two NIC without any routing work?)? Maybe you have a suggestion, how can I achieve this, as easy as possible? Maybe you have an opinion, what OS unix system do I use?

  Thank you for your time and your answers. Any useful information is much appreciated.

  Yes, it should work. You need to look out for, it's that the 'outgoing' NIC is not connected to the same physical switch as the entrant and that there is no link between these two physical switches, because this would create a loop of layer 2 on the network.

  I haven't worked much with Linux, but I don't see that you would have a problem to find some Linux/Unix with the possibility to bridge two network cards and use some software IPS to inspect the traffic.

• Transition network card, multiple network interface cards?

  Hello

  Just a quick question, does anyone know how I can fill more then 10 individual vm NIC to 10 Physics/loop back adapters? The reason why I ask, is that in the network editor it provides only 10 slots and no option to add more.

  I had a search around but unfortunately came up with nothing.

  Thanks for any info or pointers.

  The host Windows don't support 10 VMnets but a Linux host supports up to 255 VMnets.

  BTW, it's in the user manual.

• BlackBerry devices with multiple phones of switching software

  I currently use two devices BlackBerry, the Z10 for labor and the Z30 for personal use. I've done a switch of the device of a curve (previous working device) for the Z10 using Blackberry link. I recently bought the Z30 and want to make a switch of the device to my old torch for the Z30. Is it possible to do so using the same link BlackBerry program? Only, I have a PC and want to know if I get a headache trying to do or if there is a better solution.

  Thanks for any help!

  I have not ran into problems because I use two different BlackBerry ID so I had to sign without a job and then sign in to my personal account. Thank you both for your good help.

• several devices on the network with the same name

  I want to install Windows 7 OS computers on a domain with Small Business SERVER 2003.  Curiously, I see all the computers on the network, where I should be able to, but one of them WK02011, is not accessible from all Windows 7 systems because there are multiple devices with the same name on the network according to a diagnosticn check.  WK02011 is visible and accessible from other systems on the network that are runjning XP OS.  There is only one device named WK02011 on the network.  I don't have this problem with any other XP system - that is - I can see and access all of the other XP machines on the network with the exception of WK02011.  I can't access WK2011 from the server and the server indicates that it is multiple devices with the same ID.  Rename the XP would be complicated because of having to re - set up the service to the customer and then turn around and install 7 OS in the workstation in the coming days.

  How to find the ghost device double?

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows 7 on TechNet. Please post your question in the Technet forums. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

• Windows 7 network can't see multiple devices on the network

  Hi all.  I'm about to leave my hair on this issue - I hope someone can prevent the horror that would be me without hair.

  I am running Windows 7 Home Edition on a personal computer that is connected via cable to a router UVerse also providing my home with wireless services.

  A few months ago, I could see - of my PC, network and devices and printers - the two PS3, XBox systems and Samsung TV devices that are connected to my wireless network.  Apparently randomly, my computer has ceased to be able to see these devices.  After trying everything I could think of, I've finally reformatted the system (before Christmas) and everything was good again until last week when my computer stopped once more to see these devices.  I * really * don't want to reformat my system again...

  Here are some details on where I started after the last reformat:

  The PC is connected to a homegroup.

  The PC has a wired connection to the router.  The devices are connected over wireless.

  The firewall is turned on.

  AVG anti-virus has been activated.

  Network discovery, file and sharing printers and streaming media are all enabled.

  Password sharing is disabled.

  Devices could stream Netflix/Hulu as well as files on my computer (using the PlayOn Server - I've never used WMP).

  Now my devices can still Streaming Netflix/Hulu, but not the files on my computer.  The PC can't see the devices and the devices cannot see the PC.

  Here is a list of most of the things I've tried to solve (although I've done so many things, I probably don't forget some):

  I added the PC to the wireless network, so now that it is connected both cables and wireless.  I even tried to fill these connections, although I removed the bridge when I saw that there was no difference.

  I have disabled the firewall completely.

  I disabled the AV entirely.

  I switched a residential group to a working network and vice versa.

  I gave you the assigned IPs devices in the router configuration.

  I've rolled back all the windows updates installed since the last time the devices showed in the PC network.

  I've removed the devices on the network, reconnected the and reconfigured to ensure that they have the media streaming (if applicable).

  I did several reboots the PC, the router, and devices.

  I added the PlayStation Network and XBOX Live and applications hosted under NAT/game on my router.

  I have enabled file sharing for devices that use 40 encryption or 56-bit.

  Additional troubleshooting information:

  When I try to add a device using the Add Device dialog box, no device never shows.

  Under media streaming options, when I look at instruments under all the networks and Local network, no unknown device only shows (even in WMP).  All devices that * show are already set to 'allow '.

  If I have access to my router configuration, the devices will appear as connected.

  I can ping devices from the PC.

  I searched endlessly on the Internet (including other threads on this forum) and have tried all of the suggestions I thought.  The only thing I can't do is activate uPNP on my router because routers Uverse do not offer this option.  However, I don't think that it's important because my PC could see these devices for some time after my last reformat and made no changes to the configuration of the router.

  Because multiple and different wireless devices are involved, and because a reformat solves the problem, in my view, it is a Windows problem, but I can't understand what to change on my system to make things work again.

  Anyone have any ideas?

  Hello

  Thanks for posting your query in Microsoft Community.

  It's a shame that you have to format the system first and now, the problem still persists. I really appreciate the efforts made to try to resolve the problem. This can be due to any dispute of third party software due to which the connection failed. I suggest you follow the methods below and check.

  Method 1: Run the network troubleshooter to diagnose the problem.

  Run the network troubleshooter

  Method 2: start the computer in safe mode with network and then perform the clean boot.

  Step 1: restart the computer in safe mode with network and check if the problem occurs, proceed as in the link:

  See: , start your computer in safe mode

  Step 2: If the safe mode with network works, perform clean boot and check if any third-party application is causing problem.

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  Note: see 'How do I reset the computer to start normally after a boot minimum troubleshooting' to reset the computer starts normally after troubleshooting.

  Method 3: To enable the network devices to display on the network map, they must meet four requirements:

  • Must be a HOME network or work: Mapping network only display the devices connected to a HOME network or WORK location. Devices connected to a network PUBLIC or FIELD cannot be displayed using the network card.
  • Devices must be DETECTABLE: The network discovery setting allows devices to be able to be seen by other devices on the same network. For more information, please consult: , enable or disable network discovery
  • Devices must comply with the LINK LAYER TOPOLOGY DISCOVERY Protocol: Topology Discovery LLTD (Link Layer) is a protocol developed by Microsoft to enable networked devices to 'discover' each other. If a device does not use the LLTD protocol so it can not be displayed in the network map. Windows 7 computers have the LLTD protocol implemented.
  • LLTD must be enabled on your LAN connection properties: The Link Layer Topology Discovery Mapper of e/s driver and the Link Layer Topology Discovery responder must be enabled on your local area connections properties panel.

  To check LLTD is enabled, you can refer to the following steps:

  a. Select open network and sharing Center by clicking on the icon of your network down to the right of your task bar:

  b. now, click connect to the Local network

  c. now, click on Properties

  d. ensure that two LLTD options below are selected (by default, these options are still enabled in Windows 7).

  From now to try the methods above and let us know the status. We will be happy to help you further.

• start time of 10 min with the network store interface service

  When you connect, the computer crashes to the screen of welcome for about 10 minutes.  I disabled all services of 3rd parties and the problem persists.  I reduced the problem to the "shop network interface service.  When I the hell this service, I don't have no problem with long, but internet connection times no longer works.  Any ideas?

  Hello

  Alternatively, you can try to start the computer in Mode without failure, then whether the diagnostic mode safe tools providing information about the current state of problem.

  To start in safe mode keep tapping on the F8 on the keyboard key during restart until Windows starts to load. An option will appear allowing you to choose boot safe mode with networking, select it and press .

  At the end of the boot.

  http://Windows.Microsoft.com/en-us/Windows7/diagnostic-tools-to-use-in-safe-mode

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• How can I actually talk to support multiple issues with multiple devices (software, hardware, account of the question?

  How can I actually speak to technical support issues to nulitple with multiple devices (software, hardware, account problems,) I have a touch screen of hp with windows 7 Home, Ipod, home router wireless, boost, WiFi, wii, etc.... Problems with windows live net Passport vs msn Id, problems with zune vs itunes and windows media that nobody wants play nice together.

  My touchscreen notes will use only a google account, music another program, and of course until recently google was not an option on the windows phone. of course if I'm going now that I'll lose all the games and music. His tent so frustrating of any help, that nobody seems to know how often these devices and programs interact (or care) HP has been of little use, even for my provider windows, microsoft, living cells and zune etc...

  All the changes that took place this last month will help but gets boring. I consider myself pretty computer savy, but maybe not, should not this difficult. I realized about a year ago I would have hired a technician but it seems immpossible to find someone who knows enough about all of the equipment and software to really do some good. My Hp touchscreen computer does not even play nice with their own HP printers. I really regret the time and money I spent. I could every Mac.

  All of the suggestions. Even your options do not address several problems of interaction with the hardware and software all needs of problems to adapt to a single category.

  Hello

  
  To correct the software issues run the methods mentioned below.
   
  Method 1: run the troubleshooter and check if the problem is resolved.
  http://Windows.Microsoft.com/en-us/Windows7/open-the-performance-Troubleshooter
  
  Method 2 : run a SFC (System File Checker) scan and see if the problem occurs.
  http://support.Microsoft.com/kb/929833
  
  Method 3 : run Clean boot and check if the problem persists.

  
  To help resolve the error and other messages, you can start Windows XP, Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  
  Note: follow step 7 to reset the computer to start as usual after the boot process.
  http://support.Microsoft.com/kb/929135

  To solve the problems related to Windows Live and MSN to check the links below on contact.

  
  After the question in the links below
  http://support.Microsoft.com/kb/940784
  http://windowslivehelp.com/
   
  To solve the problems related to the HP touch computer
  
  Update the HP touch drivers from the manufacturers Web site.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If you need to talk to a Microsoft technician, then you can check the link below http://support.microsoft.com/kb/295539

  
  Hope that helps.

• BlackBerry smartphones POINT HOT or ATTACHMENT for BB 9310 on BOOST / Network Interface with Android Tablet operating system Ice Cream Sandwich 4.0.3 SPRINT

  I know that technically and could use step by step Instructions how to set up a

  HOT SPOT or ATTACHMENT for BB 9310 on BOOST / Network Interface with Android Tablet operating system ICS 4.0.3 SPRINT

  Please explain it to me like I'm a 12 year old (LOL)

  If you could email, mail, or call me at the following (see below) it would be MOST APPRECIATED

  David Lurie

  Affordable tracking systems

  1063 mosser road

  Building C-202

  Breinigsville, PA 18031 us.

  (610) 972-2110

  [email protected]

  P.S. If I can ever help with GPS Tracking, My Business in which I have 12 years of experience, I'll be more than happy to give back

  If push does not support the Hotspot feature there is nothing you can do.