Message from the USB port speed

Similar Questions

• Equium A60: is it possible to boot from the USB port?

  Hello

  I have an EQUIUM A60 with BIOS Version 1.90 is possible for a start of the USB port using an instead of a floppy mass storage device if yes how?

  Hello

  You can boot from the USB ports with a floppy drive floppy drive. You cannot boot from USB HDD or USB
  Boot devices: HDD, ODD, LAN, USB - FDD

• Using the usb port causes my computer to restart

  When I plug anything into a USB my computer to restart trys, it does not restart correctly until I have remove the item from the usb port.  I have a printer plugged into a USB at the back of the computer and that works fine, but if I try something else in the same port, even just a stick of memory, he knocked out the computer!  Any help appreciated.

  Hello kaydee16,

  I would say confirming that you are up-to-date with the latest firmware, drivers, and updates to the BIOS of your manufacturers Web site.

  How long have you encountered this problem?

  Did you of recent changes made to your system, before having this problem?  (installation/uninstallation software/hardware)

  What version of Windows XP and SP are you currently using?

  What anti-virus software are you currently running and when you ran a full scan last?

  Please let us know status.

  Thank you

  James

• Message from the controller USB Hi Speed

  I have an old Compaq computer, running XP Pro. About 2 months ago he locked up and I got to reformit. I reinstalled XP Pro, and it works. I tried to reinstall the printer, and now the computer says the USB ports might work faster if they were hooked to a 2.0 port, and I need to install a hi speed USB controller on this computer. The printer worked fine on this computer until I got it to reformit, and ask if there is any other drivers that I need to install. I have XP Pro SP 3.

  Thank you

  If you see a message like this:

  This USB device can perform faster if you connect it to a Hi-Speed USB 2.0 port.
  For a list of available ports, click here.

  This is an informational message and not an error message.

  You can see if you can actually fix it, or you can decide to disable your USB device messages and will see the message.  If you disable the USB of reporting mechanism, you will not be able to see all messages from USB devices either.

  Disable the notification mechanism is considered to be the 'fixing' to some people, but not for me.

  It would be better to fix it in fact instead of just to disable the notification mechanism.

  Let's see what you have right now:

  Open the Device Manager by clicking Start, run and enter in the box:

  %SystemRoot%\System32\devmgmt.msc

  Click OK.

  Do you see any red Xs or yellow? s in the list of devices and if so, in what areas?

  Now, expand the Universal Serial Bus controllers section and look for the words:

  Host improved or enhanced PCI to USB Host Controller controller

  Here is a sample screenshot of what to look for in your device manager:

  http://img43.imageshack.us/img43/2466/devicemanagerenhanced.PNG

  You see the word enhanced in all sections under Universal Serial Bus controllers section?

  If you do not see the word enhanced, you probably just update your device USB drivers.  Until you do, you will continue to see the annoying reminder message.

  If you want another set of eyeballs on your information to find out what you have, follow these steps:

  Click Start, run and enter in the box:

  Msinfo32

  Click on OK and when the system info summary appears, click on Edition, select all, copy, and then paste the information here.

  For more information of USB port, expand the components section, click on USB, click on edit, select all, copy and then past he feedback here.

  There will be some personal information (such as the user name and the name of the system), and anything that turns information private for you, simply delete the pasted information.

• due to lack of space on my HARD drive, I moved Photoslibrary to a USB port. When I connect my iPhone 6 I am able to transfer photos from my phone to the PhotosLibrary on the USB port, but when I sync, photo library is not get highlighted. Cannot synchroni

  due to lack of space on my HARD drive, I moved Photoslibrary to a USB port. When I connect my iPhone 6 I am able to transfer photos from my phone to the PhotosLibrary on the USB port, but when I sync, photo library is not get highlighted on the USB port. Cannot synchronize.

  Hello, manoj0910.

  Please visit Apple support communities.

  Looks like you can't synchronize the pictures located on your external drive.  I need a little more information about your configuration to provide a better answer.  However, we will try to sync your photos through the section of the file through the article below.  You just need to direct iTunes to where your photos are stored on your external drive.

  If your photos are in a folder

  1. Select "Choose a folder" from the context menu.
  2. Choose the folder where you store your photos.
     
  3. Click on apply.

  You can arrange photos in subfolders to create photo albums.

  Sync photos from your computer to your device iOS through iTunes

  See you soon

• C309a error message: remove the USB from the printer device

  My C309A was connected wireless via time capsule or Airport extreme for a year to the network & work find on all Macs. There was an update of the HP software to 2.4.1 on 01/07/10 and since then it won't work. I have reset to default settings, more #/ 3 reboot and it goes through the initialization process but the network configuration wizard cannot find the wireless network and the same error message finally backup on the screen and you can't do anything unless you turn off. He can come back and do not have an error code next time, but it will not find the network either... so you can shut off again and the next time the error message appears. There has never been whatever it is connected to the USB port. I have re - installed software and still have the same problem.

  Please need help or suggestions. Thanks in advance.

  E-mail: [text removed for privacy]

  Here is how to contact HP.

  Please remove the serial number of your post (Options > Edit Post).

• When I plug my Galaxy s captivate phone into the usb port on my computer, it will charge the phone but will not allow sharing of information from computer phone.

  Original title: usb with smart phone problem

  When I plug my galaxy s captivate phone into the usb port on my computer, it will charge the phone but I cannot share the news from computer to phone. In fact when I click on the computer icon, it shows the dvd, floppy disks and hard disk but not the phone. I use a mouse usb and headphones and they work fine. I tried to search for devices and it does not work. I run Defender pro anti-virus software and have checked the firewall, but I don't see that his block the phone. I don't know what else to do. Help, please. Thank you

  Hi Mike,.

  Just to follow up with you on that, that very well may be the cause. Especially when it comes to mobile phones, the real cable you use is very important to have all the features when it is plugged into a computer. Where you can try a new USB cable yet, I hope that whoever is completely compatible with this phone.

• "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

  "unrecognized usb device": error message every time that a usb device is plugged into one of the usb ports

  1. my laptop - acer aspire 5030 - has been having this problem for the last five months.

  2. I tried everything including changing service pack, as we have xp professional, he has recently upgraded to vista business 32-bit with service pack 1.

  3 tried all the methods start the laptop after a few hours, remove the battery, press the power button for half a minute, and so on.

  4. I finally he formatted a couple of times, but the problem is not.

  5. later, I improved the professional system of vista and installed the latest security patches, but the problem remains

  6. now, I started to update its drivers, although the device is identified to be connected, but is not recognized. "the error message" not recognized usb device "appears. I try to reinstall the drivers or upgrade of drivers, it does not. It displays the message "the drivers for this device are to this day.

  7. initially, the connection of the device, the drivers are installed but still the device does not show in Explorer.

  8. I tried to change some registry values by merging a regedit file in the registry - for display devices that are not present; but still, it has failed.

  9. I then tried to delete the file infcache1.inf in c:\windows\system32\inf, but the problem persists.

  10. Subsequently, I tried to create another registry entry to "disable selective suspend" in HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB by adding DWORD and assigning a binary value of 1.

  11. I tried later also to uninstall all the system devices including USB controllers, drives and the storage controllers, who must still without success.

  12. I tried to see if the drivers in safe mode, which they did not.

  13. I tried to delete the following registry entries =

  HKEY_LOCAL_MACHINES\System\CurrentControlSet\Enum | USB PORT; HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10318 & HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Class\ {4D36E967-E325-11CE-BFCI-08002BE10200.  The computer does not have alow it.

  14. the BIOS indicates device pnp "disabled", which I also look for the BIOS settings, which do not allow me to change to change existing ones.

  15. I have not found the WINDOWS\SYSTEM32\drivers\USBSTOR file. SYS in my driver store. This affects the system?

  16. I also contacted manufacturers pnp devices that provided me with most recent and versions compatible drivers for my devices - namely an apple ipod & Seagate external HARD drive - but even after that the drivers are installed properly and the system rebooted the problem remains. Is this something to do with the updated playing driver registry entries does not after the update? OR is what registry entries are configured to only read the entries at the time of the installation of the OS?

  17. I also contacted local sellers who have suggested to me to change the "motherboard". This will help as a last resort?

  18. in the meantime I had also installed other operating systems to Linux - Fedora and Ubuntu; Full Windows XP - Home & Professional and Vista Edition. All these have been installed successfully but do not solve the problem of usb.

  19. I have also raised the original HARD disk & replaced by another HARD disk. also checked the power of all ihee and ehee usb ports to be at least 5 V. I also disabled the automatic deactivation of devices usb by the system. physical contact, ports and connecting cable is fine. the distribution of power is set at 10% for the ihee ports and 20% for ports ehee, which is what is should be the physical output is also close to 5V for all ports connected.

  20. all professional (hardware or software) should any solution for the problem of the usb ports on my laptop?

  Something that you haven't tried:

  How to fix USB device not recognized in Windows

  http://www.online-tech-tips.com/computer-tips/USB-device-not-recognized/

  I hope I could help

• My HP 14 laptop is not recognizing the usb ports and wifi at startup.

  During the last few days I been dealing with the issue that my laptop does not recognize the usb ports and wifi. After several reboots, it works fine. My drivers are up to date, so I don't know why, I'll have this terrible problem.

  Welcome @hildergarn,

  Thank you for visiting the Forums HP's Support and welcome! It is an excellent site to find answers and ask questions. I understand that you have a problem with your Wi - Fi and USB ports on your laptop from HP.

  My first suggestion would be to use the wireless network troubleshooting and Internet tool. At the bottom it will ask you questions to help you diagnose the problem.

  Please take a look at this great Charter called troubleshooting wireless network and Internet. This document will help you to solve the problem of Wi - Fi.

  Have you tried to restore the BIOS?

  Have you tried to connect directly to the Modem/Router?

  You have uninstalled the driver in Device Manager?

  Please try to uninstall the driver in Device Manager by using the following steps:

  • Go to the Device Manager.
  • Expand network adapters.
  • Right-click on all NICs individually.
  • Click on uninstall.
  • Restart the laptop twice.

  How many devices you try to connect?

  What you are trying to connect via USB?

  Are - what you happened to try to use the HP Support Assistant?

  Here is a link to the HP Support Assistant, if you not him have not yet tried. Simply download and run the application and it will help with the software and drivers on your system that need updated.

  Here are other troubleshooting steps that may help too. If the USB device does not appear in Device Manager, then it might be a question of power requirement. Unplug the machine and perform the following steps until the device is detected:

  • Reboot the laptop

  • Plug in and wait five seconds.

  • If the device does not appear, try connecting to another USB port.

  • If the USB device is displayed in Device Manager after you connect the cable to a different port, then uninstall and reinstall the software of USB device driver.

  If the device is not recognized in any port, unplug it and go to the next step.

  • Open the Device Manager.

  • Double-click Bus USB controllers,

  • Double-click on a USB root hub,

  • Click the Power tab

  • Click on properties of power supply (if it is displayed).

  Devices need that are connected to the hub are shown, as well as the power they have. If the total displayed power is more than 500 mA, remove the devices and use a hub powered.

  • Continue looking at the properties of the power of each USB hub. If the total power required exceeds the total available power for the hub, then remove a device on this hub to a decrease in the number of consumption.

  • Plug in and wait five seconds. If the device is not recognized, unplug and go to the next step.

  Please note; Remove USB cables at high speed that are more than 3 m (9.8 ft) in length and use cables at high speed that are shorter than 3 m.

  Source: troubleshooting USB connections - please look at this document and follow all the steps in it.

  When we came to a resolution, please share what has worked for you with others by marking this post as an acceptable Solution. If you do not want to show your appreciation for my efforts today, please take a second to click the Thumbs Up button below.

  If please re-post and let me know the detailed results of all the troubleshooting steps in this post. Could you please provide me with your model number (How can I find my model number or product number?) also.

  Can't wait to hear from you!

  Have a great day!

• SQosmio G50 - 10 H - one of the usb ports stopped working

  Hello forum,.

  I have a BOUNCING problem with usb ports on my qosmio g50-10 h.
  There are two ports on the right side of the machine and I have 2 self-powered 7 centers of port (usb 2) attached to these.

  Every now and then to stop it from ports and of course all the parts a unregcognised, not found.
  I get error messages saying unregognised device or usb device stopped working or windows stopped device etc.

  Unplug the hub and repluging it ususally actually come back to life.

  any ideas?

  Stafford

  Hello

  Have you tried to connect devices directly to the USB port?
  Try this and see if the USB device is disconnected, as you mentioned that using the external USB hub.

  Generally speaking, it is difficult to say what might cause this
  You could try updating the chipset driver.
  Of course, you should also check the USB port settings, and power management options for economy.

  In device manager-> USB root & hub-> properties you could disable for unique energy saving USB ports.
  This also on Win 7 power management.

• It is possible to boot on the usb port?

  Hi all

  I would like to know if it is possible to boot on the usb port? I have this message "NTDRL is missing" at the start, I guess I have to reinstall Windows on the machine?

  Furthermore, I would also like to sell my laptop (configuration: 1, 00 G/2 X 256 PM / 40 G/12XT/LM/W). How could I wait fot his laptop? Where can I sell it (it's so hard to sell such a laptop).

  Thank you very much for all your answers...

  Hello

  When you get this message it means that the file Command.com has not been found. Or because he is missing from the boot drive, or your startup drive does not work. The file could also be destroyed because of a mistake. Command.com is used on versions of Windows that load on the BACK as Windows 3.0, 95, 98 and me. Command.com is not used on NT, 2000, XP. They use the NTDRL file to load. The BIOS reads the start section of the reader to know what file to load. If the system is on the NT platform and you get this error, then the boot sector is damaged or the hard disk is damage.

  Well, you write t n what kind of phone it is. How will I know that means this unit cost? I put t know this model.

  Nevertheless, you should check the prices on Ebay.

  Good bye

• Store data from the Serial Port in the buffer and then take action?

  Hello! Everyone,

  I'm new to LabVIEW and I take assistance from various videos and stuffs available online to get started with LabVIEW.

  But I have a duty, therefore needing help.

  initially I see some of the tutorial videos and learned about the LabVIEW interface, and does a little project to communicate with the Port series (receiving and sending data).

  Happens to my task.

  My LabVIEW application will send a few State request packets on my device or control and based on the response packet that I have to display values.

  The Structure of package is as

  Header, length, Op_Code, data Checksum

  There is no terminator as newline or carriage return or anything else.

  In C language, I read the data from the Serial Port, and based on the length, I conclude that I got the full package or not, and then by recalculating the checksum value, the integrity of the package is verified and then based on that Op-Code has been sent will be decided.

  (I'm dealing with hexadecimal data)

  But how can I do this in LabVIEW.
  A tutorial or any referece will be useful for me.

  1. I suggest that you learn to use Shift Registers instead of local and global variables.  They are much more efficient (memory and execution speed) and make it much easier to read the schema.

  2. you don't need this inside the loop property node.  Is there a way to configure a Serial Port to turn off the stop character.

  3. you don't need to wait for playback VISA will limit the rate of loop if no data is coming.

  4. Once you have the length, you simply read the rest of the entire message and process it at a time.  This will make things a LOT faster.

  5. you should really do this enum a def type so that you can ensure that all your enum constants have the same values.  If you need to add a State later, simply update your enum in the same place then.

  

• U2413, calibration solution Ultrasharp fails to connect to display via the USB port

  Dell U2413 SN: CN-0YCM0F-72872-48P-A81L REV A01 August 2014

  Try to run the ultrasharp Dell V1.5.3 on this monitor calibration solution, however, the software stops and displays "please connect the screen to your computer via a USB cable." I click the OK button after you have checked that the USB port on the computer is connected to the USB connection screen, but ultimately, this message appears:
  "Could not establish a connection to the screen. Please make sure that the USB cable is connected and try again. »

  Has tried this on two different computers, running Windows Pro 8.1. One was connected to the monitor cable HDMI to DVI (Thinkpad 10 via docking station), the other using the provided Dell Display Port printer for (Tablet Thinkpad X 230) mini display port cable.

  The USB ports on computers were connected the Dell supplied USB 3 cable to the monitor. Also tried this on a single computer by using a USB 2 port and a USB cable with the same result. The USB connections on the monitor seems to work ok when you plug a flash drive or the i1 Display Pro. Also, did a reset Monitor USB and verified that Windows has seen additional generic hubs when the USB Monitor is connected to the computer. There are 4 additional hubs when you use additional 2 usb hubs and USB 3 cable when using the USB 2 cable. In addition, power cycled the monitor several times (as recommended in the version that is known for this problem) without success.

  Before the attempt to make the calibration:
  A factory reset on the monitor.
  Ran the monitor self test and SUBMISSION. No problem found.
  Monitor purchased from Dell November 2014

  Same result with V1.5.7

  Any suggestions? Where should I go from here?

  I had success in the U2413 of profiling. I pulled out an old workhorse, a Thinkpad T43
  under Windows XP. Then installed the ultrasharp Dell V1.5.3 calibration solution and all
  updates available from Microsoft, but no other software - nothing of the Dell-supplied with
  the monitor. Used the DVI - connection DVI and USB 3 cable supplied with the monitor. The
  software Profiler has worked well with this configuration. When the program first took to the "Start
  Screen measure"(where the problem occurs already noted) Windows (message status bar)
  has reported that he accessed software Realtek 3.0. So I focused on research at the Realtek
  software on other systems.

  On the Thinkpad 10. There were two 1. "Realtek Card Reader" and 2. «Realtek USB 2.0 Card Reader» I have
  removed both and reinstalled the software Realtek for Dell monitor CD. Insert an SD card and
  a USB in the monitor and both were seen by Windows Explorer. There was also a Realtek USB
  3.0 card reader to showing in Manager devices under USB controllers. Using the connections between the T10 to monitor previously described the Profiler software, then ran normally.

  X 230 - I removed the "Realtek Card Reader" (V6.2.9600.30168) software and tried to start the
  Software Profiler and it does not at the same point as before. Then I installed the Realtek USB 2.0
  Software for the Dell card reader. However, there was still no Realtek USB 3.0 card reader
  display in the Manager of devices under USB controllers. Software Profiler is not like before. I then
  inserted an SD card in the monitor and the "Realtek USB Card Reader 3.0" appeared in the device
  Manager. Software Profiler, then ran normally.

  So now my two systems Windows 8.1 software profiling will not work if the 'Realtek USB 3.0 Card '.
  Reader"is not listed in Device Manager. To do this the software must be installed (for example
  starting from the Dell CD) AND an SD card must be inserted into the SD slot on the monitor. Remove the SD card
  Card and the device disappears and profiling software will not run. Insert an SD card and the
  Software Profiler works normally.

  How can I get the "Realtek USB 3.0 card reader ' to automatically load before running the Profiler software?

• My keyboard is not recognized by windows when connected to the USB ports.

  My keyboard is not recognized by windows because that is malfuncioned or something else, that's what I get a message when I insert the keyboard to the usb port that could do because the ports are fine.

  Original title: keyboard problem

  Hi Caragata,

  Perform the steps from the link below and see if it works.

  Tips for solving problems of USB devices

  Note: This article also applies to Windows 7. If the fix it does not work, you can then run the built-in utility.

  Good day!

• The Device Manager on my Windows box lists a hub USB 3.0 as one of USB controllers. This means that one or more of the USB ports are capable of 3.0?

  I recently bought a backup disk says he would run faster is it my 3.0 instead of 2.0 USB ports.

  Just try to understand the computer itself, if one of the 8 USB ports on my desktop Dell (Windows 7, 64-bit box) is capable of USB 3.0.

  Hi John,.

  The message that Windows gives is Windows telling you put a USB 3.0 device in a USB 2.0 slot and the speeds will be Cap using USB 2.0 footrest.

  If you are looking for your system on the website of Glens, it should tell you if one of the USB ports are 3.0 or not.  I think that USB 3.0 is marked with the blue wire around the ports.