Migration of disks of Ultra6 DEAD + my new 516

Similar Questions

• Satellite L350-235 a restore disk runs on a brand new HARD drive?

  Hello

  My hard drive is dead (completely) 3 days out of warranty.
  Recovery discs has not yet loaded, all I had was a black screen and a mouse pointer.

  So I bought a new hard drive. Problem I have now is how to install Windows on a new drive.
  What should I get Toshiba?

  I obviously paid for Windows Vista, when I bought the laptop, so I'm a little confused on what to do next.
  A restore disk will work on a whole new drive?

  Thanks in advance

  Hello

  Didn t drive recovery does not happen with the laptop because you had an option to create one using the preinstalled Toshiba recovery disc creator.

  You now have this disc which can be ordered here:
  https://backupmedia.Toshiba.EU/landing.aspx

  Boot from that disk and follow the instructions on the screen.
  The recovery disk works also with the new HARD drive!

• Migration Assistant tips - model 2009 to 2016 New

  I would like to use the Migration Wizard to move date of old new iMac, but was one could move "crud".  Any advice?

  Old machine is 2009 3.06 GHz Intel Core 2 Duo running 10.8.5.  It may be shocking slow (more than a minute to answer a click sometimes).  Concern that the hard drive may be out.  I used Migration Assistant to least an older eMac it before and quite possible an original iMac before that.  So there are many old things lurking there in.

  I've already implemented the new machine slot a new name (some say bad idea).  However, new machine has been used for web and e-mail Web since he was pulled up.  So maybe I can go and rename?

  I don't have a ton of time to move much more than the docs if I don't use MY that I don't have time to learn all the intricacies of what lies where.

  Great dangers if I use MY or just hover over the docs and start over?

  Thanks in advance for any advice!

  You must use the Migration Wizard the first time you start your new Mac, after that it will create another user admin and that can cause you problems. Wipe the drive and start again are the simplest solution. Most of the "crud" is small files that not harm. To determine if one of your crud is harmful, please download and run EtreCheck. It is a diagnostic tool that is very useful for us to find problems. It will also give us additional specifications on your Mac. After his execution after the logfile here. It will never contain any personal information.

• Migration of disks between RN104 and RN204

  Can I ask?

  I have RN104 with WD RED (xraid, raid 5 FW 6.4.0). 4x3TB I think buying new RN204 unit.

  Is it possible to migrate all records of old RN104 in new RN204 unit without formatting and copy data?

  Yes.

  1. place a working drive (must not be your table) in the 204

  2 update the firmware on the 204 to 6.4.0

  3. check that the firmware update was successful

  4 power down, remove the disc from work

  5. move your drives in front of the 104 at 204 (keep the same order).

• I'm trying to migrate data from a server to a new one with the file permissions of the files of users and records lost.

  original title: robocopy

  I'm trying to migrate data from a server to a new one with the file permissions of the files of users and records lost. So far, that's what I did, I used \\server1\share \\server2\share/sec /mir robocopy and robocopy \\server1\share \\serve2\share/e/s /copyall. It seams like they copied all files with the permissions of the user for the files, but not files. For example, if a user makes a folder with the files in the folder appear them have permissions appropriate for them but not the root folder or subfolders, they did... How can I fix this and what is the difference between / s /mir and/e/s /copyall?

  Hello

  You can find the Server forums on TechNet support, please create a new post at the following link:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• How can I transfer my ISP settings (cable) on a disk for transfer to my new computer?

  Transfer

  
  

  How can I transfer my ISP settings (cable) on a disk for transfer to my new computer? am NOT computer savvy, so I need a specific answer.

  am using disks, there is no much to transfer >

  Thank you

  You want to just save your ISP for Windows Mail account settings?  WinMail in: tools | Export of accounts & save export on the desktop. Copy disc and place it on the desktop of the new machine. Reverse the import process in the new email client.
   
  Are you sure that's what you're looking for?

• I've just migrated from my 2009 IMac to a new 5K, the creative cloud somehow app is corrupt and does not

  I've just migrated from my 2009 IMac to a new 5K, the creative cloud somehow app is corrupt, I uninstalled the old app.  Downloaded the cloud app creative new & re-installed but I just get an empty window and no apps showing or even a login screen

  Migration of Mac with Time Machine WILL NOT WORK with the Cloud program activations due to hidden files

  Sign out of your account... Uninstall... to run vacuuming...

  -Restart your computer... Sign in to your account... Reinstall

  -using the vacuum after the uninstallation and reinstallation is necessary before

  -http://helpx.adobe.com/creative-cloud/help/install-apps.html (and uninstall)

  -http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

• Can I migrate vista windows of a dead to a new machine?

  Recently, the hard disk went on a laptop I bought in 2007.  I had been running Windows Vista.

  To replace it, I'm Mid-building a new PC, and I'm price of BONES.  Like almost everyone, I would like to avoid paying the full cost for windows 7.  So, while it may be a long shot, my question is this: is it possible to switch the license for Vista my old machine, death has a brand new (for the purposes of backup and just get the W7 upgrade)?
  Sorry if this is silly and my thanks!

  If your copy of Vista comes with the laptop, then no, you cannot migrate to another computer.  Windows OEM copies are related to the motherboard of the computer, they are provided with and may not be used on another.  If you bought a copy of Vista retail, then you can transfer.

  If you create a custom computer, you will need to purchase a copy of the full license of Windows for that.  Do not buy an OEM System Builder copy from a retailer like Amazon or NewEgg.  OEM SB packs are for custom builders, selling computers to customers.  A person who built his own computer is not a builder of sytem as defined by the Microsoft license program.  Such a person is a do-it-yourselfer.  The correct license is retail.

  Don't buy Windows 7 on a discounter in line, the Amazon Marketplace or eBay.  The internet is full of counterfeits produced in China.  They are very good imitations, as you can see in this video:

  http://www.YouTube.com/watch?v=hzqNNiOM0cs

• Migrate messages from the Macbook Air to new iMac 2012 2016

  How can I migrate all my messages (text, iMessage) of my Macbook Air to my new iMac 2012 2016? I have a lot of messages on my laptop and I want to migrate them to my iMac just to have them for reference/memory later. I do this because I would like to activate the monthly updating of message on my iPhone, so he won't have to queue all my messages it years ago and I am also reformat my old Macbook Air. Is there a way to do this? Thank you!

  Messages and e-mail accounts and data are found in/Home/Library/Messages/and/Home/Library/Mail/files. Just copy the content to the same folders on the new computer.

  Or you can migrate your complete folder from the old computer to the new home. This can be done using the love at first sight between the two cable and on the new computer using target disk Mode use the Migration Wizard to migrate your application. It could also be run from a time Machine or another external backup drive.

  Migration will not overwrite any user account that has already been created on the new computer. MY simply creates a new Admin user account name. You will then need to switch to the newly migrated account.

• Migration of PPC-based Mac to all new MBP running El Capitan

  Can use Setup Assistant to migrate files from a Mac to Leopard PPC processor to a whole new MacBook Pro running non-retine El Capitan cause problems? The support article 'Move your content to a new Mac' (https://support.apple.com/en-us/HT204350) said the old Mac should run 10.6.8 Snow Leopard or later, but that has not been my experience on November 24, 2015.

  When my new MBP came directly from the China (I paid the extra $15 for express delivery) and I was starting for the first time, I plugged on my old based on the PPC PowerBook G4 10.5.8 Leopard and when I got to the screen "you want to transfer your data", I chose "transfer from a Mac", hit continue and expected to see an error screen.  Surprise, surpise, transfer stepped forward, and all my accounts and passwords have been transferred to the MBP.  I used a Firewire 400 to 800 cable to connect two computers and started the G4 in target Mode.  The only 'problem' I have noticed (if that's the right word) is that my new MBP is found with the same name as my old G4.  I expected to wonder on behalf of MBP somewhere along the line, the installation procedure.

  Then I came across two problems related to the system with the MBP, but I don't know if they were related to the transfer or were part of a problem with the original, factory system or the 10.11.1 updated, which I fell right after the end MBP of the initialization of the first time.  The first problem was the MBP would not print at one of my printers Epson (Stylus CX7400 and Stylus Photo R280), even after downloading what it determined were the correct drivers. I would get an error message "failure of the filter.  The second problem was that the MBP would not cCREATE a bootable of El Capitan Installer using the Terminal and the command SUDO appropriate.  Both these problems disappeared after I reinstalled completely El Cap 10.11.1, but I still want to know if transfer in my info to the G4 PPC-based using Setup Assistant might have caused or contributed to them.

  Very likely that the system software and some of the apps would not be compatible with a mac intel. Music and photos would be. And also movies. But all third party apps will need to be updated to work. If you have used assistant migration there is a screen where you can choose what are the files to be transferred. Ether transfer you the contents of the entire hard disk or your entire home folder. That's how you're done with the same user name. Relocation of El Capitan straightened some of them. You should always go through and remove some things.

• Migration of disk OCR_Voting

  Hi Experts

  Please I need your advice with this:

  Oracle Rac 11 g 2

  Oracle Linux 5.9

  ASMLib is used

  We´ve bought a new storage hardware, so we´ve been migrate old ASM disks on start it up, replacing them with the new discs (new storage).

  1 - I create new disks (new storage) ASM

  2.-j' add the disks to the current start

  3. - I'll drop the old records of start

  So far, well, now turn to it s for the diskGroup OCR_Voting, its a disk group with normal redundancy. ´

  So I have the doudbt, I can do the same procedure for the diskGroup OCR_Voting?

  I found this blog:

  Basic concepts of Oracle and grid data: migration online, groups of disks of one SAN to another ASM

  I want to be sure and have a second expert opinion.

  I'd appreciate your advice and thank you for your time

  Concerning

  I followed the same procedure enemy the DiskGroup OCR_VOTE to migrate records online

  11 GR 2:

  1 - I create three new discs ASM (new store)

  2.-j' add the disks to the current OCR_VOTE DiskGroup

  3. - I'll drop the old records of three of start

  Thank you

  Concerning

• How can I migrate my old synchronization data to the new system when I signed in devices

  I just reformat the hard drive of my computer and reinstalled Windows and Linux. Now that I have installed and updated, Firefox wonder to migrate to the new synchronization system they have. Problem is, I still want to be able to connect to the old system just to be able to get my favorites so I can migrate to the new system.

  I always sync my key and the connection information for the old system, but I just want to know how to access it once for the information available to me. I can handle everything from there.

  Hello, in this case you'd probably have to use a workaround and download the previous firefox version, disable the automatic update for the moment (in options > advanced > update), bind it to the old account synchronization and upgrade after you successfully restore your data in this way...

  Install an older version of Firefox

• Compaq Presario SR1150NX: Error, disk Compaq recovery dead

  Hello, I have a desktop Compaq Presario SR1150NX of 2005. Everything works well in it and we emptied dust not for long. But then, one day I went to start it it says a critical system file was missing. I'm confused at first. After half an hour, creating a USB disk only to find it didn't work, I then had to use the Windows XP Recovery Console. Then after I fixed it it still didn't start because it couldint find the file. But when I start the computer, it shows me that, if I press F10, it boots into system recovery mode. OT started and told me that I could boot into windows xp system recovery. But in the middle of this, the computer overheats and shuts down. When I tried to turn it on again it gave me a disc error AND when I boot in recoervy, it's just bluescreens. Now when I turn on the computer, it does nothing.

  Is there any where where I could download a recoervy tool to open the hard drive in order to get the data on the drive and get a new drive? Or get a Windows recovery disc?

  Any help is the Apprecited!

  Remove the disk from the desktop.

  Buy

  USB 2.0 for HDD SATA/IDE adapter 2.5/3.5/5.25IN drives w / adapter

  See: http://www.ncix.com/detail/usb2-0-to-sata-ide-drive-adapter-a3-17762.htm

  and connect your hard disk with this adapter to a USB port on your computer.

  When you connect, Windows will ask your permission to run 'check disk' ('CHKDSK') to review and fix any problem of file system.

  I think that the corrupt currently-system files on the hard drive is causing startup problems you reported.

  Re-connect the desktop "repaired" disk drive, and then try again.

• Portege R500-11Z: recovery disk to help prepare a new HARD drive

  I bought a new hard drive (SSD) for my R500-11Z and I put in an envelope with the USB cable before installation - I want to be able to format the drive and create a new copy of Windows XP before you get out of my existing hard drive.

  I'm looking for ways to use the recovery disk and it SEEMS that it should be possible... EXCEPT...

  I discovered that on the recovery disk there is an executable called recoUNPACK in the Tools folder, which should, in theory, restore the contents of the disc to the hard drive. However, because the new hard drive is plugged into my existing XP set up, he gets a folder called System Volume Information written in it. The presence of this file causes the recoUNPACK to fail. He gets, at 59%, every time, and then survey the error - System Volume Information already exists.

  Any person proposing the deletion of the folder should consider their knowledge of the XP - there is no way to do this, ask Mr. Google if you don't believe me. I also tried this with full of this folder write permissions so that, in theory, could replace recoUNPACK...

  I would be very grateful if someone knows a way of "forcing" crush the System Volume information folder or another way to 'restore' the recovery of my new hard drive disk (other that disassemble the laptop and substitute physically the disc!).

  I have reviewed various options for establishing a USB bootable drive, but as I will adapt it in my laptop I don't want running all versions of XP - so using the recovery disc supplied with my odd R500. All bootable USB I can find only programs, fat32 format, and I would stay in NTFS...

  And the reason why I want to do it this way, it is that I want to continue to use my existing hard drive until the news is ready - its supposed to be an effective way to work... but so far the time wasted, trying to restore the disks could have been better spent undoing the screws on the rear of the machine!

  Thanks in advance

  > However, because the new hard drive is plugged into my existing XP set up, he gets a folder called System Volume Information written in it. The presence of this file causes the recoUNPACK to fail. He gets, at 59%, every time and then lift the error - System Volume Information already exists

  Hmm the right path and the letter of the partition or volume entitled did you use?

  As far as I know that the command should show something like this:

  + recounpack.exe d:\imagename.tpa z: f +.

  (z: is the letter of your external USB drive and may be different in your case)

• Dead on new DVF-L700 pixel

  Right Out of the box my new DVF-L700 has a dead pixel considering this is a replacement unit after the encounter the same problem, I'm starting to wonder about the quality checks at the Japan! Someone else who has experienced?

  It's weird. We tested the monitor 1 on 2 F55 and the same dead pixel was visible. This is certainly a dead on the screen pixel. Now, I tested the 2nd monitor with SDI (the F55 no) signal and it was very good. So I recorded a black signal off the F55 and looked into the content browser. I was scared to death when I saw the dead on recorded media pixel!

  So I called my distributor of Sony. Then he gave me this magic trick: 3 black balances in a row. I did it... And the problem was gone. I repeat: 3 balances black to get rid of them pixels dead. It's a trick that works with almost all cameras Sony CMOS.