Mini of the UCS + 4 switches, no VLAN
Hi all
I have a mini UCS with 6324 modules e/s with B200 m3 x 5 blades, each ESXi 6.0 running.
I want to uplink the UCS mini with four cables to four switches separated for traffic, and I wish that each host ESXi b200 see four separate vmincs, one on each network. The switches have no VLAN, but running DHCP. I want to get DHCP from each card.
How can I go on the correspondences between the vNIC? Groups of LAN Pin?
Hi Alex,
That is right. You can also implement Layer 2 disjoint explained in the guide below for more secure access.
http://www.Cisco.com/c/en/us/solutions/collateral/data-center-virtualiza...
I hope this helps.
Qiese Sa'di
Tags: Cisco DataCenter
Similar Questions
-
Helps the clarification on the ports of the UCS C220
Hi guys New computer unified (and the servers / virtualization in general to be honest!) Sorry for stupid questions, I guess. I tried to read as much as I can but still a little fuzzy on a few things.
At the back of the UCS C220 I have, there is a M, 1 LAN, LAN 2 port, and then a 4 ports ethernet card. What I guessed was:
M's management for MMIC port
LAN 1 and 2 were for ESXi (grouping of NETWORK cards?)
So do not know what is the purpose of the ethernet card 4 ports as well?
In addition, the MMIC, you have the option for dedicated/shared LOM etc and I don't really understand the differences. I guessed who dedicates meant that MMIC used the port of M and LOM shared meant she could use other LAN ports? Furthermore, making MMIC and ESXi had to be on separate subnets?
Sorry for stupid questions, but once I have clearly in my head I think it will be easy for me,
Thank you
Hello
If I have CIMC running in "Shared LOM" then it means I can have 1 cable connected from one of the LOM ports and can access both the CIMC and ESXi on a single cable without the need for the management cable to be connected?
Yes, the only cable connected to the LOM port will give access to interface MMIC and ESXi.
In this case the CIMC and ESXi can also be on the same subnet without problems? (Assuming switch with single vlan)
They can be in the same subnet and won't cause problems
Padma
-
Moving to the stack of switches
Hi all
* We currently have 3 X N2048 outside of the firm network switches.
* They are so interconnected with a regular LAN cable.
* We have setup a VLAN on a single switch while the other two using VLID 1.
What we should do to pass to a configuration of the battery? (I have the cables on the spot).
Thanks in advance for any helpful answer.
There is a stacking Dell network guide. It's for the N4048, but the steps and concepts are the same for the N2048.
stacking is also covered in the guide of the user on page 189.
Once the switches are stacked, the main unit is the unit that is configured and contains the configuration for the entire stack. The backup device keeps a copy synchronized the config. In this spirit, I would backup the current configuration of the switch that has the additional VLANs on this subject. So what to do to be a master in the stack. The battery must then use the config of the main switch, with the access mode by default for the VLAN 1 to additional ports. If for any reason it is not, you can use your backup configuration.
I hope this helps.
-
prepare the config for the model/tool switches
Guys,
I'm trying to find out if there is a tool to prepare config Cisco routers/switches. I'm looking to prepare the basic config with some VLANS, static IP, etc. of the AAA. Should I use GNS3 as Simulator to simulate a router and configure it to serve as a model or if there is another free light weight tool where I can test config for typo errors or something.
Thanks in advance!
If you have existing switches just the running-config and get some simple editor like Notepad and change the IP addresses and other things
Add No. SHUTDOWN on the interfaces, because by default they are not upward, and when you do a show running-config it does not appear as no. SHUTDOWN.
-
Hi Expert,
How to distinguish the physical interface and logic (subinterface) interface to the Cisco router/Switch? Can you please clarify a formal way for this so have?
A physical interface is numbered with the same name of the interface when printing on the physical port. For example "GigabitEthernet 0/1" corresponds to port 1 of the 0 module (or the base unit).
A logical interface can be a subinterface on a routed port and will have a point ("". "") preceding the number sous-interface (ex. GigabitEthernet 0/1.1). It can also be a loop or a virtual interface (on a router this could also include interfaces like the tunnel and virtual tunnel or VTI types). A switch may also have a VLAN logical interfaces (e.g. interface vlan 1) which are used as layer 3 virtual interfaces of type.
-
Make two cheating SG200 four switches with vlan
Hello
I have two switches SG200 I want to divide it into 2 VLANS totally independent.
My guess is that I could create a VLAN #2 and then assign 1-24 of VLAN (default) #1 and ports 25-48 of VLAN #2.
Do the same with the second switch.
And finally connect the cable from the port 1 switch 1 to port 1 of the 2 switch and
another cable to port 25 on switch 1 to port 25 on switch 2.
For some reason, devices can bee 'ping' on the same ports vlan switch 1 but cannot reach the devices on the switch 2.
Is there a way to do this with SG200 switches?
Thank you
It is a valid topology.
Any individual connection to the router should be UNTAG vlan 1 and vlan 2 UNTAG.
Any connection host for the vlan 1 should be vlan 1 UNTAG, any connection host in vlan 2 should be vlan 2 UNTAG. Marking only that we care is between the switches, 1u, 2 t trunk. Everything else is respectively not marked.
-Tom
Please mark replied messages useful -
the UCS blade iscsi initialization cannot install windows server
Hi all
I have a problem when I try to install windows server 2008 in the storage of nexenta using iSCSI via ucs b-series, but his works well when I install ESXi 5.5. I can't find disk under windows server installation, and I see all the LUNS in ESXi what im create before nexenta storage and work when I install it.
This vnic iSCSI Configuration:
----------------------------
vnic_id: 13
LINK_STATE: to the topInitiator Cfg:
initiator_state: ISCSI_INITIATOR_READY
initiator_error_code: ISCSI_BOOT_NIC_NO_ERROR
VLAN: 0
DHCP status: false
IQN: test: iqn.2014 - 11.com.:8
IP address: 192.168.1.59
Subnet mask: 255.255.255.0
Gateway: 192.168.1.5Cfg of target:
Target the Idx: 0
State: ISCSI_TARGET_READY
State of PREV: ISCSI_TARGET_DISABLED
Target error: ISCSI_TARGET_NO_ERROR
IQN: iqn.2010 - 08.org.illumos:02:windowsboot
IP address: 192.168.1.49
Port: 3260
Starting logical unit number: 6
Ping statistics: success (986.646ms)Info session:
session_id: 0
host_number: 0
bus_number: 0
target_id: 0can anyone help me to solve this problem?
Thanks in advance - Fabre
ENIC / fnic driver must be installed. they are not part of any Windows operating system.
they can be found in
Unified Computing System (UCS) Drivers - 2.2 (3)ISO image of drivers based on the UCS
UCS-bxxx - drivers. 2.2.3.isoDepending on the version of the UCS.
-
Hello
I have problem with manager Cisco UCS, after have logged you in the UCS Manager, I get an error.
Cristobal,
It certainly is a cause of what UCSM bug doesn't do what it is supposed to and the only bug which is really (according to the version you are using) is https://tools.cisco.com/bugsearch/bug/CSCum95854/?reffering_site=dumpcr and seems to be fixed in the latest versions... 2.2.2c; 2.2.3A; 2.5.1a; 3.0.2c (UCS Mini)
Advice is to contact TAC for assistance (if necessary).
-Kenny
-
The UCS Central + Disjoint layer 2
We would like to migrate to use UCS Manager 5 cloves separated the Central use of UCS. We are looking for the best way to set up a VLAN global everything using an infrastructure Disjoint Layer 2. It seems I would have to create across the world and assign them to a profile in a BASKET for them to get pushed down to this POD, and then in the UCS Manager I would have to get in the VIRTUAL LAN Manager to assign the VLAN for the uplinks appropriate. Is there a way that we can implement the Manager of vlan in Central UCS or maybe a way to push the VLAN down to the PODS at the beginning then do not remember to do only after the VLAN has been assigned to a profile?
Hi Jason
Check https://communities.cisco.com/docs/DOC-35264
1.3.1a release has the following features:
....
Ability to push the VLAN / VSAN Global to areas of the UCS without using an association of Global SP
.....
Walter.
-
Replacement of the corporate network switches how ESX and VM will react?
We replace all our switches in current network with new gear. All our ESX network connections are redundant (console, vmotion and virtual machine) with each connection associated with a different switch (for example the virtual machine NIC is connected to different switches and the same for other groups of ports). I was wondering what will happen when migrate us to the new switches. We intend to make this port a port at a time. My guess is that when we have the first virtual machine network cable and move again preconfigured port switch all the VMS on this NETWORK adapter will switch to the other NETWORK adapter as if it was a failure. The migrated Server NETWORK card will be auto-negotiation with the new port and become availble for use but VM will not request for load balancing between the two network cards. We then will at some point to move the other virtual machine from the old network card switch to a new switch and the VM are switched to the new other switch port and as the first card NETWORK occurs autonegotiation and the nic will become available. But how do I get the network traffic balancing across both connections of NIC's virtual machine? I understand that load balancing of virtual machine through the NETWORK interface only to the market and vmotions card - is this true and if so how can I force a reload balance or even manually load balance... Thank you
Failback only works when you run active / standby NIC. If you are running active-active, you can set the host mode maint, let it drain and then leave the mode maint to allow virtual machines to come back and live on some Teddy they land on.
With respect to the passage of the switch the riskier part is to make sure that you have all the VLAN defined on the 'new' switch and that there is a layer 3 path to the front door of this switch. When you migrate the first server I would put in mode now, put some DRS in manual mode and then make the transition. Then a vMotion machine virtual not essential (or 1 VM for each VIRTUAL local area network) on to this host to make sure that the installer of L2 and L3 works correctly. Make sure that the field of L2 on the old switches can talk to the L2 area on the new switches.
Ben
-
Really slow Mac Mini on the first commissioning
I bought my Mac Mini because the old PC had an age to start up. Now, my Mac Mini is even worse. I also have an old portable (2010) I installed Windows 10 on, and it is much faster than my Mac! W10 is up and running on browser/email before Mac even gets to the user login page!
Advice on other posts, I ran EtreCheck and updated a printer with the HP software problem. Got sorted and it really helped. But its just as bad party, ran EtreCheck again, the results below, but while the Mac was still loading up, it's done intentionally to see if I can find what it keeps. There is nothing obvious in this, can we see something that miss me it please.
(Aware there are other posts like this but saw someone do an admonition to add their isses at the same post accusing them of 'thread-jacking')
EtreCheck version: 3.0.3 (307)
Report generated 2016-09-17 08:11:02
Download EtreCheck from https://etrecheck.com
Duration 11:48
Performance: Poor
Click the [Support] links to help with non-Apple products.
Click [details] for more information on this line.
Problem: Computer is too slow
Mac mini (late 2012)
[Data sheet] - [User Guide] - [warranty & Service]
Mini Mac - model: Macmini6, 2
1 2.3 GHz Intel Core i7 CPU: 4 strands
4 GB of RAM expandable - [Instructions]
BANK 0/DIMM0
OK 2 GB DDR3 1600 MHz
BANK 1/DIMM0
OK 2 GB DDR3 1600 MHz
Bluetooth: Good - transfer/Airdrop2 taken in charge
Wireless: en1: 802.11 a/b/g/n
Graphics Intel HD 4000
S236HL 1920 x 1080
OS X El Capitan 10.11.6 (15-1004) - since startup time: less than an hour
HTS541010A9E662 disk HARD APPLE disk0: (1 TB) (rotation)
EFI (disk0s1) < not mounted >: 210 MB
Macintosh HD (disk0s2) /: 999,35 go-go (607,22 free)
Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB
Receiver IR of Apple, Inc..
Apple Inc. BRCM20702 hub.
Apple Inc. Bluetooth USB host controller.
Apple Inc. Thunderbolt_bus.
Mac App Store and identified developers
/ Library/Application Support/Avast/components/fileshield/not signed
[loading] com.avast.AvastFileShield (3.0.0 - SDK 10.9-2016-08-18) [Support]
/ Library/Application Support/Avast/components/proxy/not signed
[loading] com.avast.PacketForwarder (2.1 - SDK 10.11 - 2016-08-18) [Support]
[no charge] 7 tasks Apple
[loading] 154 jobs Apple
[running] Apple 77 jobs
[cannot] com.apple.security.syspolicy.plist (2015-08-23)
[no charge] 45 Apple jobs
tasks of Apple 155 [loading]
Apple tasks 90 [performance]
[cannot] com.adobe.ARMDCHelper.cc24aef4a1b90ed56a725c38014c95072f92651fb65e1bf9c8e43c37a2 3d420d.plist (2016-07-12) [Support]
[performance] com.avast.secureline.update - agent.plist (2016-07-04) [Support]
[loading] com.avast.secureline.userinit.plist (2016-07-04) [Support]
[performance] com.avast.update - agent.plist (2016-08-22) [Support]
[loading] com.avast.userinit.plist (2016-08-22) [Support]
[loading] com.google.keystone.agent.plist (2016-07-12) [Support]
[loading] com.oracle.java.Java - Updater.plist (2016-08-23) [Support]
[loading] com.adobe.ARMDC.Communicator.plist (2016-07-12) [Support]
[loading] com.adobe.ARMDC.SMJobBlessHelper.plist (2016-07-12) [Support]
[loading] com.adobe.fpsaud.plist (2016-06-29) [Support]
[loading] com.avast.init.plist (2016-08-22) [Support]
[loading] com.avast.secureline.init.plist (2016-07-04) [Support]
[loading] com.avast.secureline.uninstall.plist (2016-07-04) [Support]
[loading] com.avast.secureline.update.plist (2016-07-04) [Support]
[loading] com.avast.uninstall.plist (2016-08-22) [Support]
[loading] com.avast.update.plist (2016-08-22) [Support]
[loading] com.google.keystone.daemon.plist (2016-09-02) [Support]
[loading] com.microsoft.office.licensing.helper.plist (2014-02-26) [Support]
[loading] com.oracle.java.Helper - Tool.plist (2016-08-23) [Support]
[cannot] com.adobe.ARM. [...]. plist (2014-09-02) [Support]
[loading] com.avast.home.userinit.plist (2016-08-22) [Support]
[loading] com.avast.secureline.home.userinit.plist (2016-07-05) [Support]
[loading] com.f - secure.sync.BTCloud.plist (2015-07-31) [Support]
[cannot] com.lastpass.LastPassHelper.plist (2015-04-14) [Support]
com.spotify.webhelper.plist [running] (2016-09-11) [Support]
iTunesHelper Application (/ Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Dropbox application (/ Applications/Dropbox.app)
FlashPlayer - 10.6: 22.0.0.209 - SDK 10.9 (2016-07-19) [Support]
QuickTime Plugin: 7.7.3 (2016-07-22)
AdobePDFViewerNPAPI: 15.017.20053 - SDK 10.11 (2016-08-03) [Support]
AdobePDFViewer: 15.017.20053 - SDK 10.11 (2016-08-03) [Support]
Flash Player: 22.0.0.209 - SDK 10.9 (2016-07-19) obsolete! Update
Default browser: 601 - SDK 10.11 (2016-07-22)
SharePointBrowserPlugin: 14.6.7 - SDK 10.6 (2016-08-25) [Support]
nplastpass: 3.1.89 - SDK 10.10 (2015-04-14) [Support]
Silverlight: 5.1.41105.0 - SDK 10.6 (2015-12-21) [Support]
JavaAppletPlugin: Java 8 update 101 build 13 (2016-08-23) check the version of
WebEx64: 1.0 - SDK 10.6 (2015-07-17) [Support]
Web of Google Earth plugin: 7.1 (2013-10-07) [Support]
LastPass - LastPass - https://lastpass.com (2015-09-04)
Flash Player (2016-06-29) [Support]
Java (2016-06-22) [Support]
Time Machine not configured!
update_dyld_shared_cache 17%
8% kernel_task
6% WindowServer
1% systemstatsd
1% com.avast.daemon
Top of page process of memory: ⓘ
905 MB update_dyld_shared_cache
Kernel_task 421 MB
152 MB Safari
Dropbox 147 MB
Mdworker (10) 127 MB
137 MB free RAM
3.86 GB used RAM (1.10 GB being cached)
67 MB used Swap
Sep 17, 2016, 07:50:32 self-test - spent
I suggest you remove the Avast software according to the instructions of developers. You need anti-virus software on your Mac and often through other reports Avast here seems regarded as a cause of potential problems.
If you do remove it, restart the Mac and the test. If it makes any difference once Avast is removed, you can always reinstall it if you feel that you need (even if you haven't).
-
How can I activate the function tab switch?
I used the function tab switch a lot, and now it has been removed. Is there a way to activate it?
Make sure the open tabs is checked.
- Tools > Options > privacy > address bar: when you use the location bar, suggest:
History Bookmarks [X] Open tabs
-
Is my Apple iPad WiFi Mini unlocked the cell plant (Verizon)?
Is my Apple iPad WiFi Mini unlocked the cell plant (Verizon)? It was purchased at Apple December 2013. He is a certified refurbished by Apple
Yes.
-
What is the best HDMI switch for use with Apple tv 4
What is the best HDMI switch for use with Apple tv 4. I heard some do not work and the automatic switch has problems because Apple tv is still using power?
I installed on a cutting and not because the automatic switch works because it isn't always. It came with a remote control that is almost as good, so don't mind the fact that automatic switching does not work well. The reason why I chose cutting is because it was the first device that gave me the good picture and sound quality with my AppleTV, the Xbox 360 and the PS4. (Don't ask!)
-
I'm looking to move from Windows/Apple/Logic Pro X and Cubase Cubase.
My questions have to do with the current (2014) Mac mini, specifically the i5 $999 2.8 GHz with 8 GB of RAM.
This computer will be powerful enough to run Logic Pro X DAW and Cubase 8 courses without any problem?
I would say yes, but I post here too:
Maybe you are looking for
-
the font on my messages box is too large and I can not find where to change it
When I open Mozilla for new messages in the in box, police in messages is way oversized and almost impossilbe to read. I don't have this problem using IE
-
TREE Design with optional filtering parameters
Trying to practice in the creation of my own VI regarding the existing available for LabView 8.5 - design of FIR filter with optional parameters. Everything I created is the same as what was expected, but he pops an error which I do not know what it
-
the windows update icon is constantly on and I don't know why... If I put the updates automatically update... help
-
Had the new hard drive installed on my computer, so now, two weeks later, the computer tells me that I need to activate Windows with the product key code. The product key code label is too so I can't read the code. I called Toshiba for a new or a r
-
I have HP Pavilion dv6-6b25tx Entertainment Notebook PC product number-B0N59PA #ACJ and I am using Windows 7-32 bit. I tried to download the latest drivers for my pc, but on the HP website driver for 64-bit are available, so what do I do?