the UCS blade iscsi initialization cannot install windows server
Hi all
I have a problem when I try to install windows server 2008 in the storage of nexenta using iSCSI via ucs b-series, but his works well when I install ESXi 5.5. I can't find disk under windows server installation, and I see all the LUNS in ESXi what im create before nexenta storage and work when I install it.
This vnic iSCSI Configuration:
----------------------------
vnic_id: 13
LINK_STATE: to the top
Initiator Cfg:
initiator_state: ISCSI_INITIATOR_READY
initiator_error_code: ISCSI_BOOT_NIC_NO_ERROR
VLAN: 0
DHCP status: false
IQN: test: iqn.2014 - 11.com.:8
IP address: 192.168.1.59
Subnet mask: 255.255.255.0
Gateway: 192.168.1.5
Cfg of target:
Target the Idx: 0
State: ISCSI_TARGET_READY
State of PREV: ISCSI_TARGET_DISABLED
Target error: ISCSI_TARGET_NO_ERROR
IQN: iqn.2010 - 08.org.illumos:02:windowsboot
IP address: 192.168.1.49
Port: 3260
Starting logical unit number: 6
Ping statistics: success (986.646ms)
Info session:
session_id: 0
host_number: 0
bus_number: 0
target_id: 0
can anyone help me to solve this problem?
Thanks in advance - Fabre
ENIC / fnic driver must be installed. they are not part of any Windows operating system.
they can be found in
ISO image of drivers based on the UCS
UCS-bxxx - drivers. 2.2.3.iso
Depending on the version of the UCS.
Tags: Cisco DataCenter
Similar Questions
-
Cannot install Windows server 2012
Cannot install Windows server 2012. Whenever I get * error
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers) -
Cannot install Windows Server on the new server Poweredge T110 II 2012
HI - just took delivery of my new Dell PowerEdge T110 II with two 1 TB drives in RAID 1, but without any operating system installed. On the Windows Server 2012 Standard edition installation, the installation routine is unable to detect readers when it comes to choosing the installation location. I can 'find the pilots', but on the insertion of the Dell supplied DVD, it does not find everything. I changed different settings, rebooted and tried several times without success. Entering the system at boot configuration screens, I can clearly see my 2 x 931GB disks and the virtual drives installed on them (I even removed the implementation of RAID and the virtual drives at some point to see if that was the problem). Any help appreciated. Regards, Barry
Hello Barry
You should have received a disc entitled management of system and Documentation Tools. If you start on this DVD, it takes an option to install an operating system. Follow the on-screen instructions and it should load the required drivers. If this does not work then let me know what RAID controller you have.
Thank you
-
Cannot install windows server 2012 on VM
Well, I installed virtual box. I downloaded the ISO and VHD in windows server 2012 but will not be accepted by the Virtual box?
Josh,
I would have you post here.
http://social.technet.Microsoft.com/forums/en-us/w7itprovirt/threads
Back to us for problems with Windows in the future.
-
Cannot install Windows updates (has no status) on the computer desktop and laptop
Desktop (Purchase date: 13/07/2010)
Model: Pavilion p6402f or 6402f
Product: BK275AA #ABL
Serial No.: {removed privacy}
OS: Windows 7 Home Premium Service Pack 1 64-bit
Product ID: {removed privacy}
Portable (Purchase date: 14/07/2011)
Model: Pavilion g6 Notebook PC
Product: QD317UA #ABC
Serial No.: {removed privacy}
OS: Windows 7 Home Premium Service Pack 164-bit
Product ID: {removed privacy}
Description of the problem: same problem on the computer desktop and laptop at the same time began: cannot install Windows updates (has no status)
No hardware changes or software recently made to the system: I followed the usual procedure to install Windows updates.
Method of connection: wireless
Technical expertise: intermediate level
Performed troubleshooting: because the error # 80071 A 90 type indicated by the system, I followed the instructions of Windows Help and Support, for example to run Microsoft Fix it which did not work; a more advanced method has also been used, who recommended to start Windows Update in Mode safe, then open Windows Update and install the updates and then restart normally. At this point, the problem was that any stage of Windows Update was available.
Hello amib004,
As much as I know, only Windows Update cannot be run in safe mode. That being said, I saw where install several updates may conflict with each other. Try to disable all updates installation and install the updates failed one at a time.
-
Cannot install windows XP on the Satellite Pro A200-1N2
Jin
I have a Toshiba Satellite A200 - 1N2 PSAE3E and I don't want Vista on my laptop. I downgraded the bios to V5.30 but still cannot install windows xp and there is still no optin for SATA in the bios.
Can someone help me?
Thank you.
Hello
Did you install the SATA drivers first?
You need this driver to recognize the HARD drive!You must download the Intel Matrix Storage Manager. You should find it on the page of the Toshiba driver or the Intel Web site.
You must perform the installation of an external USB FDD drive using the F6 key during the installation of Win XP.
-
WinXP pro Setup cannot find that any installed HARD disk so cannot install windows. Unfortunately after many attempts to use rescue and recovery to restore the factory settings and for some reason constantly default... After leaving another utility popped up giving me the opportunity to erase the HARD drive and so I did... After fact as well and all I had was a blank screen, no windows more or no matter what utility to reinstall windows, then I used my winxp pro installation CD, but the program installation would continue not after a certain point by saying that the installation did not find any HARD disk installed. followed by "ensure that any disk HARD r turned on and correctly connected, and that no matter what material associated drive configured correctly, this may involve running a manufacturer provided diagnostic or Setup program. Clearly it took me by surprise. What was supposed to be a cut to white erase and reinstall now me baffled and angry. Formats the HDD of the solution? If so why didn't not the usefulness of lenovo do... If not, what is the problem? Someone help pls
Welcome to the forum!
Go into the BIOS (F1 at startup), set the "compatible" SATA mode (NO AHCI), then press F10 to save and exit, and you should be all set.
Good luck.
-
Cannot install window updates 14 altogether 646 of the code
Cannot install window updates 14 altogether 646 of the code
luckyslap,
read the problems known in this page, they explain what to do. There is a link to a fix the article.
http://support.Microsoft.com/kb/2258121
Let us know if this helped.
-
I got an asus computer notebook windows vista, upgrade from vista to windows 7, now I'm not able to do a clean install of windows xp, when I try to install XP, it says that hard drives are not connected & windows cannot find not the hard drives, so once again installed windows 7, is there a way to overcome this problem Why do I get the message windows xp does not detect hard drives? I even formatted the hard drive & tried to install Xp, but still, I get the same message.
The answers will be appreciated...
Thank you
Because the Windows XP installation CD does not have the necessary disk controller drivers. You will need a floppy drive to provide the drivers of controller for the installation program, or you will need to burn a CD of Windows XP with the controller drivers slipstreamed into the installation. A CD of Windows XP with SP2 included may have the necessary drivers.
John
-
Get the error code 641, cannot install Windows updates.
Reluctant to do a reinstall of windows. I had the same problem, find the same useless information on a cure. I did a reinstall of windows (Vista) and partially by installing the updates of windows I ran into the same problem again, the windows installer does not. Even from scratch will get not anywhere, leaving you at least your system as it stands leaves can be used instead of a partially updated with no program system.
I wonder if Apple has this kind of problem?Hello
I suggest to reset the Windows Update components and check if it helps.
Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
How to back up and restore the registry in Windows XP
http://support.Microsoft.com/kb/322756
How to reset the Windows Update components?
http://support.Microsoft.com/kb/971058/en-us
Let us know if it helps.
-
Cannot install windows 7 using the uefi on hp laptop
Cannot install windows 7 in uefi on computer mode hp laptop.
What is the error you received? Generally the new laptops are designed as is not compatible with windows 7, as a mine.
When I try to install W7 it up without hard drive found.
-
Original title: Install windows 7 on GTP style partition
Nice day
I try to install windows 7 on my laptop but there is a massegeSay cannot install windows on the selected drive cos it's GTPPartion of style, I was using before windows 8 but then formatMy hard drive please guide me on how to archive this because only throughI'm really frastratedHi Nnrmalata,
1. you are trying to install 32-bit or 64-bit Windows 7?
2. What is the brand and model of your computer?
Boot from GPT is only supported for 64-bit of Windows 7 on UEFI-based systems.
For more details, refer to this link:
http://msdn.Microsoft.com/en-us/Windows/hardware/gg463525.aspx
If your computer does not support UEFI, back up your important data to an external drive and delete all partitions on hard drives and create a new partition.
(a) start from the Windows 7 DVD
(b) click on install now
(c) in the configuration screen, click Custom (Advanced)
(d) click on drive Options
(e) select the partitions to format
(f) click on Format - this will erase EVERYTHING on this partition
(g) create a new partition, and then select a partition to install Windows on.
(h) follow the on-screen instructions and install Windows.
Note: Converting a hard disk partition or volume from NTFS to FAT32 requires that you reformat the partition, which deletes all the data on this subject. Be sure to back up data that you want to keep before you begin.
You can check the link for reference:
http://TechNet.Microsoft.com/en-us/library/dd799232 (WS.10) .aspx
Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
If above did not help, please refer to the steps in this link.
Note: Backup your important data to an external drive
Change a Table of Partition GUID drive on a main boot drive
http://TechNet.Microsoft.com/en-us/library/cc725797.aspx
Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.
-
Cannot install Windows on this disk selected disk.the has a MBR partition table.
On EFI systems, windows can be installed only on GPT disks.
When I try to install WS2008R2 in my turn lenovo G580 i5-3210 as a dual-boot option.
Hello Pratap ReddyBh,
As you try to install Windows Server 2008 R2, it would be better for you to ask your question in the TechNet Windows Server forums.
Click on the link here for TechNet.Thank you
Marilyn
-
I formatted my hard drive and xp wouldn't charge b/c he didn't see the hard drive. I then installed Windows 7 starter and cannot be upgraded. .
Probably, you need to boot in the BIOS of the computer and changed on the hard drive in IDE mode, SATA, so it can be recognized by Windows XP.
Before that you plan to replace Windows 7 with Windows XP. Have you tried to familiarize yourself with the operating system first?
http://techingiteasy.WordPress.com/2009/08/19/for-the-former-Windows-XP-user-welcome-to-Windows-7/
If you want to run Windows XP, you can consider to dual boot Windows 7 and Windows XP. You first need to know if your computer is compatible with Windows XP. Much more modern computers are gradually support for Windows XP.
How dual boot Windows 7 and Windows XP
http://notebooks.com/2011/02/01/how-to-dual-boot-Windows-7-and-Windows-XP-Part-1/With Windows XP installed first:
http://notebooks.com/2011/02/17/how-to-dual-boot-Windows-7-and-Windows-XP-Part-2/ -
Hello
I'm doing a clean install of windows xp pro on a hard disk with unallocated space at the front of the drive and a primary partition containing the data at the end of the training.
I want to install windows xp pro on a primary partition on the front of the disk on drive C.
Here's my problem:
When I was installing windows xp pro, I noticed that when I created a partition in the unallocated space at the front of the car where I wanted to install windows xp pro, that I couldn't C as a drive letter for the installation drive - d only.
I ran the installation at the end and Yes, windows xp pro did install on drive D - this isn't what I want - I want it on the C drive.
Can someone tell me how I can solve this installation problem.
Should I run a partition boot CD and set up a primary partition on the front of the drive before installing windows xp pro?
Thank you very much.
I solved this problem by following these steps:
1. I installed a second hard drive (old sata drive).
2. I installed windows xp on the second hard drive.
3. I photographed the windows xp install from the second disc on the first hard drive.
4. I deleted the second disc.
5. I've rehearsed with my other computers.
Everything works fine - just takes a little longer than expected.
Maybe you are looking for
-
Satellite C850-B820 shuts off when I take off my power cable
Hello I bought laptop Satellite C850-B820 2 months there is use to this normal subject, 2-3 hours a day, I was working on it without the power connected, the status of the battery was at 50% so I plugged in to recharge, suddenly power left and return
-
The second image lost in CAN communication when use card NI PCI-CAN/XS2
I recently had a problem on CAN communication. I need commmunicate a Cluster with CAN BUS, baud rate is 500 Kbps, the BOX is card NI PCI-CAN/XS2. The operating system is Windows XP. normally, the PC send a Cluster command, then reread a frame of data
-
Basic image - launch actor actor
I have a problem, I have a core "player". When we use the actor 'launch' to "Actor Open Core front panel", it is possible to know if already "basic player" is actor started and advanced. I call several times to "Launch player", a "core of the actor"
-
I can even enter my c: documents of my network, but I can't get my computer to start after entering the password it accepts.
-
1102W shows 'offline' on the connected HP - Can t Print
I have a HP 1102W on my home network and we work very well with my HP Chromebook as the computer. All of a sudden, my impression are do not print and they indicate "error" when I look at my history of print jobs. Yet when I look at Google Chromebook