Minimize the possibility of using the partial time clause with imagecopy backups >? <

Similar Questions

• Why the execution time increases with a while loop, but not with "run continuously?

  Hi all

  I have a problem of severe weather that I don't know how to fix it because I don't know exactly where it comes from.

  I order two RF switches via a data acquisition card (NI USB-6008). One job at the same time can be selected on each switch. Basically, the VI created for this feature (by a colleague) resets all the outputs of acquisition data and active then those desired. It has three entrances, two chain simp0le controls and a cluster table, that contains the list of all the outputs and some practical information to know what is connected (specific to my application).

  I use this VI in a complex application, and I have some problems with the execution time, which increased whenever I said the VI, so I did a test VI (TimeTesting.vi) to determine where the problem came. In this special VI I record the execution time in a csv file to analyze then with excel.

  After several tries, I found that if I run this criterion VI with the while loop, execution on every cycle time increases, but if I remove the while loop and use the funtionnality "Continuous run", the execution time remains the same. In my high level application, I have while loops and events, and so the runtime increases too.

  I someone could explain to me why execution time increases and how can we avoid this? I have attached my VI test and the necessary subVIs, as well as an image of a graph that shows the execution time with a while loop and «run permanently»

  Thanks a lot for your help!

  Your SetReset_DO VI creates a channel whenever it is called.  And that you never delete a task.

  When running continuously, that it's as if it only runs once and LabVIEW has internal mechanisms to close references that will not be used again.  When a VI is used as a Subvi, LV does not know if she will be called again, and lacks these things until the first level VI stops. You have a memory leak.

  Just as you open and close your file outside the loop for, create your channel out of the loop.

  Lynn

• Is it possible to use images cut into slices with fluid grids CS6?

  I have 2 images cut into slices that I use in my page. The site was designed with fluid grids CS6. As soon as the page is rendered more small 1 images contracts while the other remains the same size. Is it possible to make this work or is it just not possible using fluid grids?

  It will never work right in fluid networks.  Decide which is more important to you - your concept of design or a sensitive provision.  Unfortunately, responsive web design requires compromises that some designers are not willing to do.  It is certainly not for everyone.

  Nancy O.

• Two questions relating to the archive redo logs with RMAN backup

  DB version: 11g
  
  I am new to RMAN.
  
  My database is in ARCHIVELOG mode. I intend to make a weekly backup for my db (02:00 every Monday). There will be all the incremental backups between these windows(Monday-to-Monday) of backup that I have would function for retrieving archived redo logs.
  
  
  Question1.
  I want to save the archived logs every day (for example at 23:00). How can I configure that?
  
  These are the configuration setting, that I intend to implement. I don't know how to set up the archive log backup
  

  configure default device type to disk;
  configure retention policy to redundancy;
  configure device type disk parallelism 1;
  configure channel 1 device type disk clear;
  configure channel 2 device type disk clear;
  configure channel 1 device type disk format '/u05/rman1/datafiles/rmnabackup1_%U';
  configure channel 2 device type disk format '/u05/rman2/datafiles/rmnabackup2_%U';
  configure controlfile autobackup on;
  configure controlfile autobackup format for device type disk to '/u05/rman1/control_files/rmnabackup1_%U';

  Question2.
  After that a new full backup is taken at 02:00 on Mondays, the archived redo logs accumulated since the last 7 days become unnecessary. How can I automate the removal of the archive redo logs with RMAN?

  Archive the log delete them all input command will take the destination of the log archiving log backup archive and delete this destination.

  In the log archive destination he has archived log in the sequence 1 to 100 then will he take the backup and delete any of the destination (Monday 23:00).

  In the log archive destination he has archived sequence journal 101 to 150 then will he take the backup and remove those in the destination (Tuesday 23:00).

  In the log archive destination he has archived log in the sequence from 151 to 180 so will he take the backup and delete any of the destination (Wednesday 10:00).

  It will continue like that.

  Concerning
  Asif Kabir

  -If you help brand the response as correct/useful.

• Error occurred in making the disc of recovery with Dell backup and recovery

  Mr President.

  When I was doing a System recovery DVD with Dell backup and recovery when all steps were completed and finally when he was checking the disc a dialog box appears showing "AN ERROR has OCCURRED". How to get rid of this error?

  Please answer fast. Any suggestions will be appreciated

  Thank you

  Hey Himanshu Teli,

  Please provide the model of your operating system and Dell. I would also recommend that you try a flash instead of a DVD disc.

• Get the response time more with First_Rows Hint.

  Hello
  I use 10.2.0.1.0 oracle version. I have a sql query that gives performance with cutting-edge FIRST_ROWS problem.     I expect the best response time with suspicion of "FIRST_ROWS (5)", but his is the worst, with use of a different set of the index, which is local to the partition. Please, help me to understand, the reason behind this change in negative execution path?
  

       First query gives all the ~3488 rows within ~1 minutes but the query with HINT is taking ~15 minutes for providing initial few rows itself. 
  For second one i am not able to get the exact and estimated cardinality stats , as it was taking lot of time for completion, so providing Autotrace plan only.
       
  Main Query:

  Published by: 930254 on October 15, 2012 04:55

  930254 wrote:
  Yes, Jonathan, in fact in the first case, i 'I' table is being analyzed using an overall index, but suspicion FIRST_ROW sound using the index that is local to the partition. resulting in the digitization of all partitions of 448. I think it's causing bottleneck. Is there something like: FIRST_ROW suspicion that affect this type of systematic index scan?

  In the first case the optimizer has unnested subquery of REACTION and used to bring to the table, I, and that's what dictated the choice of index.

  In the case of first_rows (5) decided that the range index scan will take adequate data if some time he chose a different index - running subqueries in the REACTION as a subquery for filter on each line. But it is the estimate of how long it will find adequate data (and how much time he will have to run the subquery to eliminate unnecessary data) does not.

  Concerning
  Jonathan Lewis

• ISight does not record in imovie7.1.4, while at the same time recording with garageband

  MBP 2.2 GHz Intel Core 2 duo on OS10.6.8

  I have taken steps (Please read if offering suggestions).

  Here's what I did successfully for years, and now it does not work.

  While recording video directly from isight in imovie 7.1.4, I'm simultaneously garageband (4.1.2, aka GB ' 08) running and audio recording.

  When I hit 'stop' in I saw, she would generate thumbnails, I hit 'done' the isight would disappear and complete video went directly into the imovie editing area.

  Please note that I have tried the following procedures at least 3 times or more there where problems are reproducible.

  What is happening now is that isight does not generate thumbnails either and when I hit, I get the ball spinning eternal, does not close the window of the isight, & I have to force quit.would

  I tried to close GB before hitting the stop on the isight - same problem camera

  Sometimes he would record only a small part, and once I opened GB, this offer would get no audio recorded.

  Another thing that is strange is that with Go out completely, isight, would be to save and build all thumbnails with success. As soon as I opened the GB, the video would have this effect of idle power not obvious then only imovie was on.

  Here's what I've tried so far:

  1. I disconnected and connected to another account, and it worked. The video followed well, recorded in its entirety, generted all thumbnails in the Edit with GB check box.

  Here is what does not work

  2.i went back to my main account. I copied all preference files in the library, placed in another folder on the desktop, then deleted all files in preferences in the preference folder in the library. Then, I rebooted the computer - same problem.

  3. I copied all the preferences of the library in the account of the other, deleted all preferences of the main account and placed alternative account preferences, rebooted - same problem.

  4. I then put the original preferences, done a permissions repair, zap PRAM, etc... . same problem

  5. I tried to simply remove the nd imovie7plist in the folder preferences folders to host BY - same problem

  6. I tried to open another GB file from scratch - same problem

  I would like to know if there is a way I can just imovie to uninstall, and then reinstall without touching GB or Logic 9 that I installed. I don't know if the relocation means the package whole ilife by default because I also have logic 9 in which files are shared by GB, and it might spoil some shared folders, etc. ..

  Another cry in a hollow shaft, ' Hello ello OLA OL o...» »

• is possible to use either usb 6353 map with Matlab 2010A

  Hello

  On a bought a NIUSB 6353 map, but in my computer don't I i the 2010 version of Matlab. Is there a way to control this version of this map with MATLAB

  Thanks in advance

  Hello

  And thanks for posting here.

  Please write in English if you post here. Otherwise, post on the french forum.

  NI USB-6353 using the DAQmx driver, it must be used with Matlab.

  You will find several links from the NI USB-6353 by clicking here.

  And presents an additional link showing you how to use your device with Matlab: Introduction to NOR-DAQmx with Matlab tools

  Kind regards

• Is it possible to use more than 8 boards with Toshiba bulletin board?

  I want to have more than 8 boards on the Bulletin Board.
  Y at - it a setting I can change to achieve this goal?

  Not sure if you can create more 8 boards, but I guess that's the max if no other option is available in the display settings

• Is it possible to pair my iPhone with my car stereo and my hearing aids at the same time.

  Is it possible to pair my iPhone with my car stereo and tooth blue hearing aids at the same time.

  I've never been able to 2 bluetooth devices at the same time work with the phone

  If it is coupled with my car and then he throws the bluetooth headset and vice versa

  Not sure, there is a way to allow both

• Satellite Pro A120: Is it possible to use the docking station parallal port

  Is it possible to use a docking station usb with a parallel port on a satellite Pro A120, which has no parallel port.

  Therre is a BIOS setting, or is it not supported?

  Hello

  What USB docking station do you mean exactly?
  I found a camera and it seems that it s compatible with all satellite units.

  But please post one exactly USB docking station number.

• At the same time, both Firefox (with images, the other without)?

  Hello

  Is if possible to use two browsers firefox at the same time, one with active images, the other is disabled?

  Easy way on Windows: you'll need 1) the name of the second profile you have created, 2) a shortcut existing (already on the desktop, I hope) to Firefox.

  1. Create a copy of the shortcut, you can right-click on the shortcut and select send to > desktop. It will create a nice copy of second.
  2. Right-click on the copy and go to properties.
  3. In the 'Target' box, you should see something like "C:\Program Files (x86)\Firefox\firefox.exe" .
  4. After all (including the quotation marks) in the target box, add -no-remote -P <profile> where <profile> is the name of the profile that you created.
  5. For example, if the path to the firefox.exe am I guessed above, it would look like"C:\Program Files (x86)\Firefox\firefox.exe" -no-remote -P my-second-profile

  To run the second instance at the same time, simply use the new shortcut. The -no-remote flag tells him to start another process of Firefox, instead of simply to open a new window in the current.

  Never, ever run two separate processes with the same profile. This is the case, if evil.

• At the same time perform write and read

  Hello

  I use
  DAQmx NOR-USB-6259

  I have problem with parallel
  run the analog signal (for example 1000 points of writing
  by 1 second) channel Dev1/ao0 physics and at the same time read
  1000 points per second physics channel Dev1/ai0 1
  How to do this?
  I tried to use DAQmxExportSignal, but it does work well, or simply, I
  don't know how to do
  correctly maybe I should use a different
  the function?

  Best regards

  AndrzejS

  Hi Andrzej,

  Yes, it's possible, but with your device not at the same time, just with a little delay (about 1 US).

  The track is almost the same thing, you need to add 2 more channels of analog inputs to your task and use playback of multiple samples. Just check the VB Clk Acq - Int example.

  I can't help with particular code, because I'm not familiar with VB, but daqmx functions are very similar, if this change is 3 click in LabVIEW, then it must also be very easy in VB. You manage tasks, if your task contains more channels HERE you will receive samples of all channels.

  I hope this helps and let me know if I misunderstood something.

  Gabor

• Bluetooth and audio of the speaker at the same time

  I run vacation watch I want to be able to provide an audio feature on both an FM transmitter connected to the headphone jack AND Bluetooth speaker at the same time. This way people walking as well as those in their car would be able to hear the music. As it is, I have a system that works, but not both at the same time. With the level of technology that is in the computers in the House these days, that shouldn't be too difficult to configure the software to allow the two outputs. Is it possible to make this work?

  Hello Gerald,

  Please contact Microsoft Community.

  From the description of the question, we understand that you want to provide audio on the two FM transmitter plugged into the headphone jack and speaker Bluetooth at the same time. But unfortunately, we wish to inform you that it is not possible to obtain a taken audio headphone and speaker Bluetooth at the same time. As you mentioned in your post, you would be able to get the audio out through headphone or Bluetooth speaker both. You can check the Web to see if there is any third-party program that can support technology of dual audio output.

  Important: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  The above information was hoping to get useful, please return it to us if you need additional assistance.

• How to add multiple tabStops at the same time...

  Hello

  I know it's a bit basic, but I fight

  I am trying to create four tabStops in a paragraph style. That's what I have so far... but when it comes to tabStops [1], he died... I think that something is wrong with how I create the four tabStops, but I do not know what... Do you think what I am doing wrong?

  Thank you!
  Christopher

  try {}

  myParagraphStyle = myDocument.paragraphStyles.item ("Verse");

  myName = myParagraphStyle.name;

  }

  {} catch (e)

  myParagraphStyle = myDocument.paragraphStyles.add({name:"Verse"});)

  myParagraphStyle.tabStops.add ();

  myParagraphStyle.tabStops.add ();

  myParagraphStyle.tabStops.add ();

  myParagraphStyle.tabStops.add ();

  with (myParagraphStyle) {}

  appliedFont = "Lexicon No1 A tab";

  fontStyle = "Normal";

  pointSize = 8.75;

  head = 10;

  alignToBaseline = true;

  Justification = Justification.LEFT_JUSTIFIED;

  keepFirstLines = 2;

  tabStops [0] .alignment = TabStopAlignment.CENTER_ALIGN;

  .leader tabStops = [0] ";

  tabStops .position [0] = 5;

  crashes here

  tabStops [1] .alignment = TabStopAlignment.CENTER_ALIGN;

  .leader tabStops [1] = ";

  tabStops [1] .position = 10;

  tabStops [2] .alignment = TabStopAlignment.CENTER_ALIGN;

  .leader tabStops [2] = ";

  tabStops [2] .position = 15;

  tabStops [3] .alignment = TabStopAlignment.CENTER_ALIGN;

  .leader tabStops [3] = ";

  tabStops [3] .position = 20;

  }

  }

  It is possible using tabList. Here is a code that did this and sets all the properties at the same time. "with" does NOT define the properties at the same time and should always be avoided.

  var myParagraphStyle = app.documents[0].paragraphStyles.item("Verse");
  myParagraphStyle.properties = {
    tabList:[
      {
        position: 5,
        alignment: TabStopAlignment.CENTER_ALIGN,
        leader: ""
      },
      {
        position: 10,
        alignment: TabStopAlignment.CENTER_ALIGN,
        leader: ""
      },
      {
        position: 15,
        alignment: TabStopAlignment.CENTER_ALIGN,
        leader: ""
      }
    ],
    appliedFont: "Lexicon No1 A Tab",
    fontStyle: "Normal",
    pointSize: 8.75,
    leading: 10,
    alignToBaseline: true,
    justification: Justification.LEFT_JUSTIFIED,
    keepFirstLines: 2
  };