Mobility to new comments controller, do not discount
Hi all
I hit my head against the wall for the last day watching a strange problem with my wireless controllers. My current setup has been a cluster (8.0.140) foreign controller and a N + 1 alien Controller (8.01.121). I then had two Controllers (7.6.130) of anchor individual comments in a DMZ with 3 SSID being mounted on the guest.
I have installed a new controller of Anchor Guest (7.6.130) in a new demilitarized zone, built the tunnel of mobility between new comments and foreign controllers. Removed the existing anchorages among the SSID and added new comments to test connectivity. My client cannot obtain a DHCP address. If I statically assign an ip address, then I am connected but disconnects 10 seconds later.
So I install a new SSID, exactly the same as I was testing on foreigners and the new controller of the anchor. Create the mobility group the same way and test my client, works without problem. So I know that my DHCP setup is ok, my new controller of anchor is ok.
I tried to remove my old SSID and add once again, get the same results, the client cannot connect.
When I do a debug of the customer on the controller from abroad, I get the error message following which seems to be the where it is a failure:
Retry mobility anchor Packet XX.xx.xx.xx.xx.XX: Peer IP:
Once I change the anchor to old controllers on the foreign controller SSID, my client connects immediately again. I tried my new guest anchor controller on 8.0.121 and 8.0.140, but I get the same results. The fact that a new SSID works first time with the same settings (just a different SSID) baffles me. Even if I change the old SSID to no authentication, it still does not connect. I tried with 3 different customers comes to exclude one of the problems. I have also repeated the above test on N + 1 foreign controller (running 8.01.121) and get the same results Anybody have suggestions for something else to test. My apologies for all levels of different code, but also through an upgrade code for the moment. So, when you set up a new SSID that is mapped to the same vlan everything works. When return you your old controller who maps also the SSID to the same vlan it also works very well. However when you have the new anchor with the current SSID added new controller, it does not work? So when you auth enjoying a nice SSID don't see you the customer also on the controller of the anchor? To have a static and drop all 10 seconds or seems weird and you can create a new SSID on foreigners and the anchor without problem? What I would do is create a new WLAN using the same SSID, the name of different profile on the two foreigners and anchor. It should work since you mentioned a new SSID works very well. If your WLAN id is 1-16, and then create the new with id WLAN 17 or more, otherwise you will need to disable the old SSID before activating the new. -Scott Evaluate the useful ticket *. Tags: Cisco Wireless Why do not the remove-hard drive remove a disc with a new SCSI controller? Hi PowerCLI gurus, I try to use PowerCLI to automate the solution for article configuration of disks to use VMware Paravirtual (PVSCSI) SCSI adapters (1010398). Remove-hard drive sometimes gives me a misleading error when I use it to remove a hard drive with a new SCSI controller. The FlatHardDisk specified 'Hard disk 3' no longer exists, or never existed. Can anyone here explain the error? My version of vCenter server is 5.1.0. My PowerCLI version is 2.0. Here's what I've done to reproduce the error. First of all, I connect to vCenter and stop the virtual machine. $TestVM = 'TESTVM '. $TestServer = ' vcenter - test.local ". SE connect-VIServer-Server $TestServer Stop-VM - $TestVM VM - confirm: $false I add a new hard drive and store it in a variable so I can refer to it for the next steps. New hard drive '. -VM $TestVM ' -Persistent persistence" -Flat DiskType ' CapacityKB - 1024' StorageFormat - thin ' -OutVariable TempDisk I make a note of its name. $TempDisk.Name Because my VM already has 2 discs, the output is "hard drive 3. Then I add a new SCSI controller on the hard drive. New SCSI controller. Hard drive - $TempDisk ' -Type ParaVirtual ' NoSharing - BusSharingMode Now, I try to remove the hard drive from the variable to remove the disc. Remove-hard drive - hard drive $TempDisk - DeletePermanently-confirm: $false It fails with an error that says "Hard drive 3" has already been removed. Remove HDD: 12/02/2014-18:51:33 remove-hard drive the FlatHardDisk specified 'Hard disk 3' no longer exists, or never existed. On line: 1 char: 1 + Delete-hard drive - hard drive $TempDisk - DeletePermanently-confirm: $false + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + CategoryInfo: ObjectNotFound: (3:FlatHardDiskImpl drive) [Remove-hard drive], VimException + FullyQualifiedErrorId: Client20_VirtualDeviceServiceImpl_TryValidateDeviceExists_DeviceDoesNotExist, VMware.VimAutomation.ViCore.Cmdlets.Commands.RemoveHardDisk But I see that there are still "hard drive 3"! Get-disk hard - VM $TestVM - name 'hard drive 3. CapacityGB persistence Filename ---------- ----------- -------- 0.001 persist... B-DATA-01] TESTVM/TESTVM_9.vmdk Is this a bug or am I missing something? I don't think that the cmdlet uses actually the UID, but more likely a MoRef to the vSphere object that represents the hard disk. Remember that under the covers most of the PowerCLI cmdlets do calls to the vSphere API. Change the Uid, property value indicates that the hard drive connected to the new controller is a new and different purpose. And this explains why the hard drive remove does not work with the original hard disk object, it no longer exists. I constantly get the error 'could not get new comments. One or more files are missing on the server. I constantly get the error 'could not get new comments. One or more files are missing on the server. It gets a little old. I know that the files are there. There is some ongoing compatibility issue? Hi kuntzmd Please visit: http://forums.adobe.com/thread/533034 New Ipod nano is not recognized on laptop Bought a new Ipod Nano (my old one fell; broken screen). I have the latest version of ITunes on my laptop HP Envy. My sync iPhone without any problem. my old ipod nano also syncs. A did the device synchronization Tests. Results: No Ipod Touch, IPhone or Ipad found. I can also scroll to the clock and the parameters of the IPod Nano. I need help from the community before I call Apple. Thank you Hello pamelafromsonora, Thank you for using communities of Apple Support. According to your post, I see that your new iPod nano is not recognized by iTunes on your Windows PC, and you cannot scroll through the settings of the clock on your iPod. I know how it is important to ensure that you can connect your iPod to your computer/iTunes and use all the features. I'll be more than happy to help you with this. Use the article If iTunes does not your iPad, iPhone or iPod and follow these steps to see if iTunes recognizes the device, specifically these sections: When iTunes on your computer doesn't recognize not the connected device, follow these steps. Try again after each step:
If you do not see If you see If you see Now, locate the entry that recognizes the device as a camera. You should see 'Apple IPhone', 'Apple iPad' or 'Apple iPod '. Right-click the device entry, and then manually update the Apple Mobile Device USB driver.
If a single unknown device appears, follow these steps:
If you still need help, contact Apple technical support. If one of the sections above directs you to this section, you should already have right click on an entry in the Device Manager. Now, follow these steps: Best regards. Satellite Pro 6050: WLan controller does not seem to be in Device Manager I'm a novice guy with computers. Well, I re-formated my laptop and re-installed all the drivers, but my wirless lan controller does not seem to be in my device manager. in any well any help would be great Hello As far as I know that the WLan card was optional on this unit. In this case, if you bought the device with wireless network card that WLAN should appears in Device Manager. But if you bought the laptop without the WLan card you won't find it in Device Manager. PS: The recovery CD already includes the WLan driver and you don't need to t in addition no driver to install. PlayStation 3 Sixaxies Controller does not work Hello I am looking for a fix for this problem, I have a perferctly good controller and a new computer windows 7 64 bit and I would like to know why the controller does not work please help thanks Are you sure Sony support the controller on a PC? If you are just using a pilot implemented by a guy then it probably won't work on 64-bit. My advice, pick up a wired Xbox 360 controller. Windows Update uses drivers and it will install immediately. If you want to go wireless, you can use a wireless controller with the USB Gaming receiver for Windows. Paul Smith - MVP for Windows desktop experience... I crawled off NNTP - for now. Detachment Aldershot, United Kingdom. On the internet at windowsresource.net and dasmirnov.net. Please post back to let us know what works and what does not. :-) found the new keyboard controller pci hardware I had a massage n my office says "found new hardware n asked for a disk to install a driver but do not have." Anyone know what her soul? found the new keyboard controller pci hardware Simply cancel in the message and we will fix the problem manually. You say that it is a PC keyboard controller. Did you just install oee or install a new keyboard or hardware or driver changes at all on your system? You can get in trouble with your device (specifidallly the keyboard or keyboard controller) drivers. Go to the Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears. Check each device to a red x, yellow! or white? Look especially devices associated with the keyboard. These identify devices with problems probably (drivers, but also of conflict or something else). Click on each for more details and troubleshooting tips. If you need to get drivers (and you should for the keyboard and the keyboard/controller and like many others that you have time to do - they are making contributions beyond simply solve this problem), let the computer dealer or the manufacturer of the device (NOT of Microsoft Updates). In fact, you must disable automatic updates in Windows Update driver as follows: http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm. Once you have the drivers, you can install them via the Manager device as follows: http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html. This should solve the problem. If it is not or you do not find drivers for the position of keyboard controller to return with more information about the keyboard controller that you can find. The keyboard works fine without this "new material"? Tell me what you see in Device Manager on the keyboards or keyboards/controllers. Go to the Actions and click Scan for New Hardware and tell me EVERYTHING he says he says he detected new hardware. Keep clicking and copy everything it says until you get to the point where he asks a disc install a driver (before you get to that point it will ask probably if you want to search for a driver - Windows answer Yes and see if it works (it probably won't, but it's worth a shot).) Either you added something, or something that was already there became active or something that was already installed got corrupted and lost its driver and therefore act as if it was a new piece of hardware. In all cases we need to IDENTIFY this material so that we can drivers for it (or you will continue to see this message every time you start). If you are unsure that you have installed anything new, then I suggest that you only contact technique the customer computer manufactuerer by phone or chat online help to identify the material and the location of device drivers to it. I hope this helps. Good Lluck! Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly. Creating new interface controller on 5508... After you have created a new controller interface and applying, it requires a restart of the system? or is it just like the creation of a new interface vlan in one switch? I would have preferred not to do a reboot in the middle of the day... Thank you David After you have created a new controller interface and applying, it requires a restart of the system? No, the creation of a new dynamic Interface does NOT require a reboot. Driver error issues "PCI Simple Communications controller has not a driver" I am trying to connect my printer, an hp deskjet 2050 printer, but I get the message that PCI Simple Communications controller does not have a driver and PCI Serial Port doesn't have a driver... what should I do? William Go to HP and download the driver, then install it. Network Controller is not found"error message appears in the DEVICE MANAGER Hello! I installed WIN 7 Prof 64 bit on my laptop Compaq Presario CQ62-410US and Device Manager shows that the ETHERNET CONTROLLER is not installed correctly. I've been using the appropriate drivers: I tried to find a solution here: http://support.HP.com/us-en/document/c02592699 "But the" 'LAN Power Saving ' option of "System Configuration ' component is missing. I uninstalled installed new driver LAN wireless with no result. Thank you very much for your help! Miron Hello: See if it works... Now, it's to install the Ethernet controller (wired), not the wireless network controller. Make sure that you have installed the first Intel chipset driver, then restart. Then install the ethernet driver second on the list at the link below: WIN Pro 8, xbox 360, z axis wireless controller does not WIN Pro 8, Microsoft Xbox 360 wireless controller, z axis does not. Axis Z work in the calibration screen, but not in the test screen or in the games must be a driver problem, advice? Have deleted the driver to allow windows to reinstall the drivers. Installing the windows driver software 7 for the controller, still the z axis only work in the calibration screen. I thought that I had the same problem, but see the knowledge base article: http://support.microsoft.com/kb/2757006 Apparently, the problem is only with the test itself dialog box. I also jumped to the conclusion that it must be a driver problem and expects the controller does not work properly in games. However, the controller DOESN'T seem to work properly in games. (Mine is actually a Logitech F710, but it uses Xinput anyway). I hope that your Z axis controller also works outside of the test application, and the information above helps dispel the confusion around this issue. There is no problem with the drivers or controller, everything works (read below for the explanation and solution) I had the same problem, with the z axis (Left Trigger (LT) and right trigger (RT)) with a 360 wireless controller by using the adapter on Windows 8 Pro 64-bit wireless controller. He would not show the entrances to trigger (z axis) on the calibration screen. Looked online and came across this thread in hopes of finding new update of drivers, or a solution. After reading the post I quoted above, I decided to see if the z axis works in the game, and he does. I tried Street Fighter X Tekken, went to training mode and you can view entries button on the screen, and pressing the RT and LT trigger buttons, they are part of the game and my character not the corresponding move associated with the key as well as to show the button based directly on the screen. I went then the game controller settings in windows 8 and again once the game controller dialog box does not show the LT and RT (z axis) entered. Solution: the controller works fine, and not showing is not the z axis is only a cosmetic problem with the Controller dialog box. So just ignore the controller, the z axis dialog box still works in games. Add the new SCSI controller and new drive - powershell SDK Hi all I'm trying to add the new disc of paravirtual to my VMs. There are two types of virtual machines in the environment; a Paravirtual controller attached and others are without controller; so my task is to set the new drive of paravitual using powershell SDK. So far I am successful with my code if the controller is already present but the script fails when I try to attach the controller. with the error. RecommendDatastores: The method call failed because [System.Object []] contains a method named "RecommendDatastores". C:\NodeDeployment\Inprogress\Add_newPVScsiDisk.ps1:111 tank: 44 + $generatedkey = $SRM. RecommendDatastores < < < < ($storageSpec) + CategoryInfo: InvalidOperation: (RecommendDatastores:String)], RuntimeException + FullyQualifiedErrorId: MethodNotFound I know that this script is not good enough to post here because it is an initial draft, but in the script attached please help me with the present part- The Script requires a csv with VMname entry; Disksize to be attached and store cluster data OK I have it myself; I guess busnumber was the problem. He converted to INT working like charm... Now, I have to work with storage Drs IE. with the ReconfigureVM_task method. hoping that will work also... else {} [int] $busnumber = $allScSiController.Count Write-Host "paravirtualized SCSI Controller not found in $vmname... Try to add the new controller scsi and extra hard drives... » $NewSCSIDevice = new-Object VMware.Vim.VirtualDeviceConfigSpec $NewSCSIDevice.operation = 'Add '. $NewSCSIDevice.device = new-Object VMware.Vim.ParaVirtualSCSIController $NewSCSIDevice.device.key = - 222 $NewSCSIDevice.device.busNumber = $busnumber $NewSCSIDevice.device.sharedBus = "noSharing". $NewDiskDevice.device.controllerKey = - 222 $NewDiskDevice.device.unitNumber = 0 $NewDiskDevice.device.capacityInKB = ($diskSize * (1024 * 1024)) $storageSpec.configSpec.deviceChange += $NewDiskDevice $storageSpec.configSpec.deviceChange += $NewSCSIDevice $generatedkey = $SRM. RecommendDatastores ($storageSpec) $key = $generatedkey. Recommendations [0]. Key $SRM. ApplyStorageDrsRecommendation_Task ($key) } --- Concerning where is the highlighter? can find it on the new domain controller. where is the highlighter? can find it on the new domain controller. HI Maria, I can understand your concern & will help you with that. (1) Please open your PDF in Acrobat / Reader DC. (2) choose the right comment tool. (3) all tools comment will appear at the top as shown in the screenshot below. (4) select the one circled to highlight the text. You can also check the name of the tool to your mouse hovering over him. I hope this will solve your problem. In case if you still encounter any problem or have any questions please let us know. We will be happy to help you. Kind regards Nicos Hi guys, I sent my magazine for a client with a few comments. He answered me with many pages of notes and comments in the original text. Is there any feautre in Acrobat Pro, which can automatically count new comments? I know I can go page by page, but an automated process would be nice. Thanks for any info, S Make sure that you select all of the lines of code and press Ctrl + Enter, or the Enter key on the numeric keypad. Search for new comments in Acrobat Hello On our machines, we have Acrobat standard 9 (9.4.0), according to the Help file, we should be able to go to comments-> check for new comments. However, this option is not yet listed in the comments section I can't find the icon. I expect that if there is no comment in a document, the option would be it just grayed out, but it is not yet listed. What is required to display this option? So far, all our machines suffer from this problem. Thank you! This option appears only if the pdf file is part of a shared review. you will not see this to get a "plain" pdf for an overview on Collaboration Satellite P875 - 31 c - BSOD when inserting the SD card Hi all and sorry for my English. I have a problem when insert a SD card into the slot. If displays a blue screen with the missage follow:"PAGE_FAULT_IN_NONPAGED_AREA" your Pc we will be verified and then restarted itself. My laptop is only 3 months o If someone could help, I would be very happy. I try to find the time needed for the first voltage glitch ('clutch amps") since when the"clutch power"falls. Also the voltage at the point of the glitch of the amps 'clutch '. All the world run into thi Card LAN Driver - HP desktop computer. I can't seem to find the driver LAN for my PC with hardware ID below, can someone help please? PCI\VEN_10EC & DEV_8136 & SUBSYS_2B28103C & REV_07PCI\VEN_10EC & DEV_8136 & SUBSYS_2B28103CPCI\VEN_10EC & DEV_8136 & CC_020000PCI\VEN_10EC & DEV_8136 & CC_ How to restore the icon "in the taskbar" speaker? I restarted many times computer I passed to the task bar, right click and go to properties and checked the box to display the icon on the taskbar. In fact, this has ALWAYS been verified, then I hit apply and ok. No icon on taksbar. So I tried unche I have Windows 7 Professional 32 bit SP1. My system has 4 GB of RAM, but in system properties, it shows as memory: 4 GB (936 MB usable). How can I increase the usable at full 4 GB memory? Thanks in advance...Similar Questions
If you are using a Windows PC
> Control Panel > system and Maintenance > Device Manager. If requested, enter your password. In the list under Bus USB controllers, find the Apple Mobile Device USB Driver.
No Apple Mobile
USB device driverYou don't see symbols next to the Apple Mobile Device USB Driver
, 
, or 
of the Apple Mobile Device USB Driver, look for third-party software conflicts. Then if you still need help, restart your Apple Mobile Device Service or contact Apple technical support.
You see an arrow down
next to the Apple Mobile Device USB Driver, the driver with the right mouse button and choose enable from the context menu. Then if you still need help, contact contact Apple technical support.You see an exclamation point or question mark
or the Apple Mobile Device USB Driver, right click on the entry, then manually update the Apple Mobile Device USB driver.You do not see the Apple Mobile Device USB Driver
Manually update the Apple Mobile Device USB driver
I was just wondering, if the driver needed to be installed in a certain order. I also had my add on the Vodaphone mobile card plugged into slot on the side that would make a difference?
Dane :-)
else {
Write-Host "Paravirtualized SCSI Controller Not Found in $vmname.. Trying to add new scsi controller and additional Hard-disk..."
$NewSCSIDevice = New-Object VMware.Vim.VirtualDeviceConfigSpec
$NewSCSIDevice.operation = "add"
$NewSCSIDevice.device = New-Object VMware.Vim.ParaVirtualSCSIController
$NewSCSIDevice.device.key = -222
$NewSCSIDevice.device.busNumber = ($allScSiController.BusNumber.Count)
$NewSCSIDevice.device.sharedBus = "noSharing"
$NewDiskDevice.device.controllerKey = -222
$NewDiskDevice.device.unitNumber = 0
$NewDiskDevice.device.capacityInKB = ($diskSize * (1024 * 1024))
$storageSpec.configSpec.deviceChange += $NewDiskDevice
$storageSpec.configSpec.deviceChange += $NewSCSIDevice
$generatedkey = $SRM.RecommendDatastores($storageSpec)
$key = $generatedkey.Recommendations[0].Key
$SRM.ApplyStorageDrsRecommendation_Task($key)
}
Sanshis
Maybe you are looking for
The pilot and
A down arrow
Exclamation or