Module sfr ASA stuck in init.

Here's my problem. The ASA cannot reboot, reset or recover the module of sfr. I can console in the module, but it restarts it does nothing. I am waiting for a maintenance window to restart the entire ASA and see if that will fix it.

Sfr module cannot be reset, not upstairs, downstairs, or the State does not.

Data on the State of mod aircraft compatibility status
---- ------------------ --------------------- -------------
0 to Sys does not apply
IPS does not is not Applicable
cxsc does not not Applicable
SFR Init does not apply

He has already worked?

Have you tried "sw-module module sfr shut down the computer?"

Have you thought about making "sw-module module sfr" uninstall and re-imaging?

Tags: Cisco Security

Similar Questions

Module of ASA 5506 Sourcefire stuck in recovery

I performed these steps:
1. debugging-start module
2. SW-module module sfr recover configure image disk0: / file_path
3. ciscoasa # sw - module module sfr recover boot
The debug says it's over, but it never had a recovery mode. Here is the fix:

ASA - FP # retrieve SFR module sw-module Configuration image disk0:asasfr - 5500 x-boot-$5

ASA - FP # sw - module module sfr recover boot

Module sfr is recovered. This could erase all configuration data and all the

on this device and try to download/install a new image for it. This may take

several minutes.

Retrieve module sfr? [confirm]

Retrieve issued for module sfr.

ASA - FP # Mod - sfr 0 > *.

MOD - sfr 1 > * EVENT: creating the disc Image...

MOD - sfr 2 > * TIME: 13:25:58 EDT October 9, 2015

MOD - sfr 3 > *.

MOD - sfr 4 > *.

MOD - sfr 5 > * EVENT: the module is being recovered.

MOD - sfr 6 > * TIME: 13:25:58 EDT October 9, 2015

MOD - sfr 7 > *.

MOD - sfr 8 > *.

MOD - sfr 9 > * EVENT: successfully created Disk Image.

MOD - sfr 10 > * TIME: 13:27:42 EDT October 9, 2015

MOD - sfr 11 > *.

MOD - sfr 12 > *.

MOD - sfr 13 > * EVENT: start settings: Image: mnt/disk0/vm/vm_1.img, ISO:-disk0/mnt/cdrom /.

MOD - sfr 14 > asasfr-5500 x-boot - 5.4.1 - 211.img, Num processors: 3, RAM: 2292 MB, Mgmt MAC: 80:E0:1 D: 07:00

MOD - sfr 15 >: BB, CP MAC: 00:00:00:02:00:01, HARD drive:-file player = / dev/sda, cache = none, if = virtio, Dev

MOD - sfr 16 > *.

MOD - sfr 17 > * EVENT: start settings suite: RegEx Shared Mem: 0 MB, Cmd Op: r, Shared Mem

MOD - sfr 18 > key: 8061, Shared Mem size: 16, Journal Pipe: / dev/ttyS0_vm1, sock: / dev/ttyS1_vm1, Me

MOD - sfr 19 > m-path:-mem-path /hugepages

MOD - sfr 20 > * TIME: 13:27:43 EDT October 9, 2015

MOD - sfr 21 > *.

MOD - sfr 22 > status: mapping host VM 0x2aab3a800000 with size 16777216

MOD - sfr 23 > WARNING: vlan 0 is not connected to the host's network

MOD - sfr 24 > ISOLINUX 3.73 on 25-01 - 2009 Copyright (C) 1994-2008 h. Peter Anvin

MOD - sfr 25 > Cisco SFR-BOOT-IMAGE and CX-BOOT-IMAGE for SFR - 5.4.1

MOD - sfr 26 > (WARNING: all DATA ON DISK 1 will BE LOST)

MOD - sfr 27 > load bzImage...

MOD - sfr 28 > loading initramfs.gz...

Mod-sfr 29> ...................................................................................

Mod-sfr 30> ...................................................................................

Mod-sfr 31> ...................................................................................

Mod-sfr 32> ...................................................................................

Mod-sfr 33> ...................................................................................

Mod-sfr 34> ...................................................................................

MOD - sfr 35 >... ready.

MOD - sfr 36 > [0.000000] BIOS EBDA/lowmem to: 0009 fc 00/0009 fc 00

MOD - sfr 37 > [0.000000] initializing cgroup subsys cpuset

MOD - sfr 38 > [0.000000] initializing cgroup subsys cpu

MOD - sfr 39 > [0.000000] Linux version 2.6.28.10.x 86-target-64 ([email protected] / * / )

40 mod - SFR > re.com) (gcc version 4.3.3 (MontaVista Linux Sourcery g ++ 4.3 - 292)) #1 SMP PREEMPT

MOD - sfr 41 > Mon Feb 2 00:15:14 EST 2015

MOD - sfr 42 > [0.000000] command line: initrd = initramfs.gz console = ttyS0, 9600 BOOT_IMAGE = bzIm

MOD - sfr 43 > age

MOD - sfr 44 > [0.000000] KERNEL supported CPUs:

MOD - sfr 45 > [0.000000] Intel GenuineIntel

MOD - sfr 46 > [0.000000] AMD AuthenticAMD

MOD - sfr 47 > [0.000000] Centaur CentaurHauls

MOD - sfr 48 > [0.000000] PAT WC disabled due to the known CPU errata.

MOD - sfr 49 > physical RAM [0.000000] provided BIOS card:

MOD - sfr 50 > [0.000000] BIOS-e820: 0000000000000000 - 000000000009fc 00 (usable)

MOD - sfr 51 > [0.000000] BIOS-e820: 000000000009fc 00 - 00000000000a 0000 (reserved)

MOD - sfr 52 > [0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)

MOD - sfr 53 > [0.000000] BIOS-e820: 0000000000100000 - 000000008f3fe000 (usable)

MOD - sfr 54 > [0.000000] BIOS-e820: 000000008f3fe000 - 000000008f400000 (reserved)

MOD - sfr 55 > [0.000000] BIOS-e820: 00000000feffc000 - 00000000ff000000 (reserved)

MOD - sfr 56 > [0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)

MOD - sfr 57 > DMI [0.000000] 2.4 present.

MOD - sfr 58 > [0.000000] last_pfn = 0x8f3fe max_arch_pfn = 0x3ffffffff

MOD - sfr 59 > init_memory_mapping [0.000000]: 0000000000000000 000000008f3fe000

MOD - sfr 60 > last_map_addr [0.000000]: end of the 8f3fe000: 8f3fe000

MOD - sfr 61 > RAMDISK [0.000000]: 7dbe4000 - 7ffff3a6

MOD - sfr 62 > [0.000000] ACPI: USE 000FD900, 0014 (r0 BOCHS)

MOD - sfr 63 > [0.000000] ACPI: RSDT 8F3FE3E0, 0034 (r1 BOCHS BXPCRSDT 1 BXPC 1

MOD - sfr 64 > [0.000000] ACPI: FACP 8F3FFF80, 0074 (r1 BOCHS BXPCFACP 1 BXPC 1

MOD - sfr 65 > [0.000000] ACPI: DSDT 8F3FE420, A 11, 9 (r1 BXPC BXDSDT 1 INTL 20100528

MOD - sfr 66 > [0.000000] ACPI: FACS 8F3FFF40, 0040

MOD - sfr 67 > [0.000000] ACPI: SSDT 8F3FF740, 07F7 (r1 BOCHS BXPCSSDT 1 BXPC 1

MOD - sfr 68 > [0.000000] ACPI: APIC 8F3FF610, 0088 (r1 BOCHS BXPCAPIC 1 BXPC 1

MOD - sfr 69 > [0.000000] ACPI: HPET 8F3FF5D0, 0038 (r1 BOCHS BXPCHPET 1 BXPC 1

MOD - sfr 70 > [0.000000] No. found NUMA configuration

MOD - sfr 71 > [0.000000] pretend a node to 0000000000000000-000000008f3fe000

MOD - sfr 72 > [0.000000] Bootmem configuration node 0000000000000000 0-000000008f3fe000

MOD - sfr 73 > [0.000000] NODE_DATA [0000000000001000 - 0000000000005fff]

MOD - sfr 74 > [0.000000] bootmap [000000000000b 000 - 000000000001ce7f] pages 12

MOD - sfr 75 > [0.000000] (6 reservations early) ==> bootmem [0000000000 - 008f3fe000]

MOD - sfr 76 > [0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 00]

[Mod - sfr 77 > 00001000]

MOD - sfr 78 > [0.000000] TRAMPOLINE [0000006000-0000008000] #1 ==> [0000006000 - 00]

[Mod - sfr 79 > 00008000]

MOD - sfr 80 > [0.000000] #2 [0000200000 - 0000ae86dc] ==> TEXT DATA BSS [0000200000 - 00]

[Mod - sfr 81 > 00ae86dc]

MOD - sfr 82 > [0.000000] #3 [007dbe4000 - 007ffff3a6] RAMDISK ==> [007dbe4000 - 00]

[Mod - sfr 83 > 7ffff3a6]

MOD - sfr 84 > [0.000000] #4 [000009fc 00 - 0000100000] BIOS reserved ==> [000009fc 00-00

[Mod - sfr 85 > 00100000]

MOD - sfr 86 > [0.000000] #5 [0000008000 - 000000 b 000] PGTABLE ==> [0000008000 - 00]

[Mod - sfr 87 > 0000b 000]

MOD - sfr 88 > [0.000000] found SMP MP-table to 000fdac0 [ffff8800000fdac0]

MOD - sfr 89 > [0.000000] area NFP ranges:

MOD - sfr 90 > [0.000000] DMA 0 x 00000000-> 00001000 0 x

MOD - sfr 91 > DMA32 [0.000000] 0 x 00001000-> 0x00100000

MOD - sfr 92 > Normal [0.000000] 0x00100000-> 0x00100000

MOD - sfr 93 > [0.000000] area mobile start NFP for each node

MOD - sfr 94 > early_node_map [2] [0.000000] active varies NFP

MOD - sfr 95 > [0.000000] 0: 0x00000000-> 0x0000009f

MOD - sfr 96 > [0.000000] 0: 0x00000100-> 0x0008f3fe

MOD - sfr 97 > [0.000000] ACPI: PM-timer IO Port: 0xb008

MOD - sfr 98 > [0.000000] ACPI: LAPIC (acpi_id [0x00] lapic_id [0x00] activated)

MOD - sfr 99 > [0.000000] ACPI: LAPIC (acpi_id [0 x 01] lapic_id [0x01] activated)

MOD - sfr 100 > [0.000000] ACPI: LAPIC (acpi_id [0x02] lapic_id [0x02] activated)

MOD - sfr 101 > [0.000000] ACPI: LAPIC_NMI (acpi_id [0xff] dfl dfl lint [0x1])

MOD - sfr 102 > [0.000000] ACPI: IOAPIC (id [0x00] address [0xfec00000] gsi_base [0])

MOD - sfr 103 > IOAPIC [0.000000] [0]: apic_id 0, 0, 0xfec00000, 0-23 GSI address version

MOD - sfr 104 > [0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

MOD - sfr 105 > [0.000000] ACPI: INT_SRC_OVR (high level bus 0 bus_irq 5 global_irq 5)

MOD - sfr 106 > [0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high)

MOD - sfr 107 > [0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 level)

MOD - sfr 108 > [0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 level)

MOD - sfr 109 > [0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000

MOD - sfr 110 > [0.000000] Using ACPI (EMAC) for SMP configuration information

MOD - sfr 111 > [0.000000] SMP: allowing 3 CPUs, 0 hotplug CPUs

MOD - sfr 112 > [0.000000] PCI resources allocating from 90000000 (gap: 8f400000:6fbfc0)

113 mod - > 00 SFR)

MOD - sfr 114 > [0.000000] PERCPU: 53248 bytes of data from the cpu allocation by

MOD - sfr 115 > [0.000000] zonelists 1 built in node ordering, grouping on mobility. Total number of pages

MOD - sfr 116 >: 576247

MOD - sfr 117 > [0.000000] area of policy: DMA32

MOD - sfr 118 > [0.000000] kernel command line: initrd = initramfs.gz console = ttyS0, 9600 BOOT_IM

MOD - sfr 119 > AGE = bzImage

MOD - sfr 120 > [0.000000] initializing CPU #0

MOD - sfr 121 > [0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)

MOD - sfr 122 > [0.000000] TSC: impossible to calibrate against PIT

MOD - sfr 123 > [0.000000] TSC: HPET/PMTIMER calibration failed.

MOD - sfr 124 > marking [0.000000] TSC unstable due to could not calculate TSC khz

MOD - sfr 125 > Console [0.000000]: color VGA + 80 x 25

MOD - sfr 126 > console [0.000000] [ttyS0] activated

MOD - sfr 127 > [0.000000] bytes allocated page_cgroup 23592960

MOD - sfr 128 > [0.000000] Please try cgroup_disable = option of memory if you do not want

MOD - sfr 129 > [0.000000] opening of audit...

MOD - sfr 130 > [0.000000] bridge No. found AGP

MOD - sfr 131 > [0.000000] memory: 2244276 k / 2347000 k available (code kernel 4733 k, absent 388 k)

132 mod - SFR > 102336 k reserved, 2572 k data, 544 k init)

MOD - sfr 133 > HPET [0.000000]: 3 timers in 0 total, timers will be used by cpu timer

MOD - sfr 134 > [0.001999] calibration delay loop... 1056.76 BogoMIPS (lpj = 528384)

MOD - sfr 135 > [0.028995] security framework initialized

MOD - sfr 136 > [0,031995] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)

MOD - sfr 137 > [0,038994] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)

MOD - sfr 138 > [0,040993] mount-cache hash table entries: 256

MOD - sfr 139 > [0,042993] initializing cgroup subsys ns

MOD - sfr 140 > [0.043993] initializing cgroup subsys cpuacct

MOD - sfr 141 > [0.044993] initializing cgroup subsys memory

MOD - sfr 142 > [0.045993] CPU: L1 I cache: 32K, cache L1 D: 32K

MOD - sfr 143 > [0.047992] CPU: L2 cache: 4096K

MOD - sfr 144 > [0.048992] CPU 0/0 x 0-> node 0

MOD - sfr 145 > [0.049992] ACPI: Core review 20080926

MOD - sfr 146 > [0.053991] routing APIC put flat

MOD - sfr 147 > [0.058991]... TIMER: vector = apic1 0 x 30 = 0 pin 1 = 2 apic2 = - 1 pin 2 =-1

MOD - sfr 148 > [0.069989] CPU0: Intel CPU of QEMU virtual version 1.5.0 stepping 03

MOD - sfr 149 > [0.072988] Booting processor APIC 0 1 x 1 ip 0 x 6000

MOD - sfr 150 > CPU initialization [0.000999] #1

MOD - sfr 151 > [0.000999] calibration delay loop... 1249.28 BogoMIPS (lpj = 624640)

MOD - sfr 152 > [0.000999] CPU: L1 I cache: 32K, cache L1 D: 32K

MOD - sfr 153 > [0.000999] CPU: L2 cache: 4096K

MOD - sfr 154 > [0.000999] CPU 1/0 x 1-> node 0

MOD - sfr 155 > [0.106983] CPU1: Intel CPU of QEMU virtual version 1.5.0 stepping 03

MOD - sfr 156 > [0.110983] Booting processor APIC 0 2 x 2 ip 0 x 6000

MOD - sfr 157 > [0.000999] init CPU #2

MOD - sfr 158 > [0.000999] calibration delay loop... 1249.28 BogoMIPS (lpj = 624640)

MOD - sfr 159 > [0.000999] CPU: L1 I cache: 32K, cache L1 D: 32K

MOD - sfr 160 > [0.000999] CPU: L2 cache: 4096K

MOD - sfr 161 > [0.000999] CPU 2/0 x 2-> node 0

MOD - sfr 162 > [0.145977] CPU2: Intel CPU of QEMU virtual version 1.5.0 stepping 03

MOD - sfr 163 > [0.150977] Brought up 3 processors

MOD - sfr 164 > [0.151976] in Total, 3 active processors (3555,32 BogoMIPS).

MOD - sfr 165 > net_namespace [0.155976]: 1280 bytes

MOD - sfr 166 > [0.158975] NET: registered protocol family 16

MOD - sfr 167 > [0.162975] ACPI: bus pci registered type

MOD - sfr 168 > PCI [0.165974]: thanks to the type 1 for base configuration

MOD - sfr 169 > [0.208968] ACPI: active interpreter

MOD - sfr 170 > [0.210967] ACPI: (supports the S0-S5)

MOD - sfr 171 > [0.212967] ACPI: IOAPIC using for the interrupt routing

MOD - sfr 172 > ACPI [0.226965]: no dock devices found.

MOD - sfr 173 > [0.228965] ACPI: PCI [PCI0] root bridge (0000:00)

MOD - sfr 174 > pci 0000:00:01.3 [0.236963]: oddity: region b000-b03f claimed by PIIX4 ACPI

MOD - sfr 175 > pci 0000:00:01.3 [0.238963]: oddity: region b100-b10f claimed by PIIX4 SMB

MOD - sfr 176 > [0.284956] ACPI: PCI Interrupt Link [INKA] (IRQ 5 * 10 11)

MOD - sfr 177 > [0.287956] ACPI: PCI Interrupt Link [LNKB] (IRQ 5 * 10 11)

MOD - sfr 178 > [0.291955] ACPI: PCI Interrupt Link [LNKC] (IRQ 10 5 * 11)

MOD - sfr 179 > [0.294955] ACPI: PCI Interrupt Link [LNKD] (IRQ 10 5 * 11)

MOD - sfr 180 > [0.297954] ACPI: PCI Interrupt link [LNKS] (IRQ * 9)

MOD - sfr 181 > [0.303953] SCSI subsystem initialized

MOD - sfr 182 > [0.306953] usbcore: registered new interface driver usbfs

MOD - sfr 183 > usbcore [0.308952]: coupling half seat new interface

MOD - sfr 184 > [0.310952] usbcore: registered new driver usb device

MOD - sfr 185 > PCI [0.313952]: ACPI using IRQ routing

MOD - sfr 186 > [0.324000] cfg80211: using information field of static control

MOD - sfr 187 > [0.326000] cfg80211: regulatory field: U.S.

MOD - sfr 188 > [0.328000] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

MOD - sfr 189 > [0.330000] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)

MOD - sfr 190 > [0.332000] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

MOD - sfr 191 > [0.334000] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

MOD - sfr 192 > [0.336000] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

MOD - sfr 193 > [0.338000] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

MOD - sfr 194 > [0.340000] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, MPC 3000)

MOD - sfr 195 > [0.342000] cfg80211: composing the DREA for country: U.S.

MOD - sfr 196 > NetLabel [0.344000]: initialization

MOD - sfr 197 > NetLabel [0.346000]: domain hash size = 128

MOD - sfr 198 > NetLabel [0.348000]: protocols = without LABEL CIPSOv4

MOD - sfr 199 > NetLabel [0.350000]: no traffic allowed by default

MOD - sfr 200 > hpet0 [0.352000]: to MMIO 0xfed00000, IRQ 2, 8, 0

MOD - sfr 201 > hpet0 [0.355000]: 3 comparators, meter 100.000000 MHz 64-bit

MOD - sfr 202 > [0.363162] pnp: ACPI PnP init

MOD - sfr 203 > [0.364902] ACPI: type pnp registered bus

MOD - sfr 204 > [0.373117] pnp: ACPI PnP: found 9 devices

MOD - sfr 205 > [0.375853] ACPI: not ACPI pnp bus type

MOD - sfr 206 > bus [0.390113]: 00 0 io port index: [0 x 00-0xffff]

MOD - sfr 207 > bus [0.392654]: 00 1 mmio index: [0 x 000000-0xffffffffffffffff]

MOD - sfr 208 > [0.396124] NET: registered to the family of protocols 2

MOD - sfr 209 > [0,408163] hash table IP route cache entries: 131072 (order: 8, 1048576 bytes)

MOD - sfr 210 > [0.418293] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)

211 mod - SFR > s)

MOD - sfr 212 > [0,430272] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)

MOD - sfr 213 > [0.434109] TCP: Hash tables configured (established 524288 bind 65536)

MOD - sfr 214 > [0.438086] TCP reno registered

MOD - sfr 215 > [0.444206] NET: registered protocol family 1

MOD - sfr 216 > [0.447125] check if image initramfs... it's

MOD - sfr 217 > [6.518130] release initrd memory: 36972 released k

MOD - sfr 218 > [6.569185] of the Microcode Update Driver: v2.00 [email protected] / * />, Peter

MOD - sfr 219 > Oruba

MOD - sfr 220 > HugeTLB [6.588064] saved page size of 2 MB, pre-allocated 0 pages

MOD - sfr 221 > VFS [6,593576]: disk quotas dquot_6.5.1

MOD - sfr 222 > [6,595689] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

MOD - sfr 223 > msgmni [6.605316] has been set to 4455

MOD - sfr 224 > alg [6.612220]: no test for stdrng (krng)

MOD - sfr 225 > block [6.615153] layer SCSI generic (bsg) version 0.4 (large 252 load driver

MOD - sfr 226 > [6.618853] io Scheduler noop registered

MOD - sfr 227 > [6.620963] registered early io Scheduler

MOD - sfr 228 > registered [6.623461] deadline i/o Scheduler

MOD - sfr 229 > [6.625704] io Scheduler cfq registered (default)

MOD - sfr 230 > LTT [6.628422]: ltt-relay init

MOD - sfr 231 > [6.631109] init ltt-control

MOD - sfr 232 > LTT [6.662473]: init ltt-kprobes

MOD - sfr 233 > pci 0000:00:00.0 [6.664400]: limitation of direct transfers of PCI/PCI

MOD - sfr 234 > [6.667440] pci 0000:00:01.0: PIIX3: allowing Passive release

MOD - sfr 235 > pci 0000:00:01.0 [6.670447]: workarounds activation ISA DMA hang

MOD - sfr 236 > pci_hotplug [6.678607]: PCI Hot Plug PCI Core version: 0.5

MOD - sfr 237 > processor [6.686734] ACPI_CPU:00: registered under cooling_device0

MOD - sfr 238 > processor [6.690758] ACPI_CPU:01: registered under cooling_device1

MOD - sfr 239 > processor [6.694508] ACPI_CPU:02: registered under cooling_device2

MOD - sfr 240 > [6.745499] v1.2 of nonvolatile memory driver

MOD - sfr 241 > [6.747732] Linux agpgart v0.103 interface

MOD - sfr 242 > [6.751051] [drm] Initialized drm 1.1.0 20060810

MOD - sfr 243 > series [6.753517]: 8250/16550 driver4 ports, IRQ sharing enabled

MOD - sfr 244 > [7.006452] ÿ serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550

MOD - sfr 245 > serial8250 [7.258458]: ttyS1 to I/O 0x2f8 (irq = 3) is a 16550

MOD - sfr 246 > [7,266612] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550

MOD - sfr 247 > [7,271074] 00:07: ttyS1 to I/O 0x2f8 (irq = 3) is a 16550

MOD - sfr 248 > [7,276159] or floppy drives: fd0 1. 44 m, fd1 is 1.44 M

MOD - sfr 249 > CDF [7.291444] 0 is a S82078B

MOD - sfr 250 > brd [7.317314]: loaded module

MOD - sfr 251 > loop [7.328490]: loaded module

MOD - sfr 252 > [7.330818] driver Intel® Gigabit Ethernet network version 1.2.45 - k2

MOD - sfr 253 > [7.334212] Copyright (c) 2008 Intel Corporation.

MOD - sfr 254 > [7.337304] pcnet32.c:v1.35 21.Apr.2008 [email protected] / * /

MOD - sfr 255 > [7.340979] e100: Intel® PRO/100 network driver, 3.5.23 - k6-NAPI

MOD - sfr 256 > [7.344061] e100: Copyright (c) 1999-2006 Intel Corporation

MOD - sfr 257 > [7.348056] sky2 driver version 1.22

MOD - sfr 258 > console [7.353036] [netcon0] enabled

MOD - sfr 259 > netconsole [7.354877]: network registration has started

MOD - sfr 260 > [7.358495] entry: emulation of mouse button Macintosh as/devices/virtual/input/i

MOD - sfr 261 > nput0

MOD - sfr 262 > iSCSI [7.365941] loading transport class v2.0 - 870.

MOD - sfr 263 > [7.375699] driver "sd" would need to discount - use the type_bus methods

MOD - sfr 264 > driver [7.379516] "sr" needs updating - please use the type_bus methods

MOD - sfr 265 > scsi0 [7.387492]: ata_piix

MOD - sfr 266 > [7.391492] scsi1: ata_piix

MOD - sfr 267 > [7.394664] ata1: PATA MWDMA2 cmd 0x1f0, 0x3f6 bmdma 0xc0c0 irq 14 ctl max

MOD - sfr 268 > ata2 [7.398007]: PATA max MWDMA2 cmd 0 x 170 ctl 0 x 376 bmdma 0xc0c8 irq 15

MOD - sfr 269 > ata1.00 [7.555320]: ATA-7: QEMU HARDDISK, 1.5.0 max UDMA/100

MOD - sfr 270 > ata1.00 [7.558496]: 6291456 sectors, multi 16: LBA48

MOD - sfr 271 > ata1.00 [7.562297]: set to MWDMA2

MOD - sfr 272 > ata2.00 [7.718432]: ATAPI: QEMU DVD-ROM, 1.5.0 max UDMA/100

MOD - sfr 273 > ata2.00 [7.722448]: set to MWDMA2

MOD - sfr 274 > [7.726963] isa bounce pool size: 16 pages

MOD - sfr 275 > [7.728428] 0:0:0:0 scsi: access live ATA QEMU HARD disk 1.5. PQ:

MOD - sfr 276 > 0 ANSI: 5

MOD - sfr 277 > sd 0:0:0:0 [7.733798]: [sda] 6291456 sectors of 512 bytes of material: (3.22 GB/3.00

MOD - SFR 278 > GiB)

MOD - sfr 279 > sd 0:0:0:0 [7.737586]: [sda] write protect is off

MOD - sfr 280 > sd 0:0:0:0 [7.741046]: [sda] write cache: enabled, read cache: enabled, doesn'

MOD - sfr 281 > t support DPO or FUA

MOD - sfr 282 > sd 0:0:0:0 [7.744505]: [sda] 6291456 sectors of 512 bytes of material: (3.22 GB/3.00

MOD - SFR 283 > GiB)

MOD - sfr 284 > sd 0:0:0:0 [7.748396]: [sda] write protect is off

MOD - sfr 285 > sd 0:0:0:0 [7.750876]: [sda] write cache: enabled, read cache: enabled, doesn'

MOD - sfr 286 > t support DPO or FUA

MOD - sfr 287 > [7.755364] sda: unknown partition table

MOD - sfr 288 > [7.761433] sd 0:0:0:0: disk Attached SCSI [sda]

MOD - sfr 289 > [7.765315] sd 0:0:0:0: Attached scsi generic sg0 type 0

MOD - sfr 290 > [7.770345] 1:0:0:0 scsi: CD-ROM DVD-ROM QEMU, 1.5 QEMU. PQ:

MOD - sfr 291 > 0 ANSI: 5

MOD - sfr 292 > sr0 [7.777328]: scsi3-mmc drive: 4 x / 4 x cd/rw xa/form2 plateau

MOD - sfr 293 > [7.780375] uniform CD-ROM review: 3.20

MOD - sfr 294 > [7.785706] 1:0:0:0 sr: Attached scsi generic sg1 type 5

MOD - sfr 295 > basic driver Fusion MPT [7.791309] 3.04.07

MOD - sfr 296 > [7.793519] Copyright (c) 1999-2008 LSI Corporation

MOD - sfr 297 > [7.795993] SPI Host MPT Fusion driver 3.04.07

MOD - sfr 298 > Fusion MPT FC host [7.798893] driver 3.04.07

MOD - sfr 299 > Fusion MPT SAS host [7.801803] driver 3.04.07

MOD - sfr 300 > ehci_hcd [7.806451]: () 'Improved' USB 2.0 EHCI host controller driver

MOD - sfr 301 > [7.810308] ohci_hcd: USB 1.1 'open' (OHCI) Host Controller Driver

MOD - sfr 302 > uhci_hcd [7.814054]: pilot USB Universal Host Controller Interface

MOD - sfr 303 > [7.818692] usbcore: registered new interface driver usblp

MOD - sfr 304 > [7.821487] initializing USB Mass Storage driver...

MOD - sfr 305 > [7.824998] usbcore: registered new driver usb-storage interface

MOD - sfr 306 > [7.827794] USB Mass Storage support registered.

MOD - sfr 307 > [7.830759] usbcore: registered new interface driver libusual

MOD - sfr 308 > PNP [7.834894]: PS/2 controller [PNP0303:KBD, PNP0f13:MOU] 0 x 0, 60 x 64 irq 1.1

MOD - sfr 309 > serio [7.841445]: 0 x 60 i8042 keyboard port, irq 0 x 64 1

MOD - sfr 310 > serio [7.844551]: 0 x 60 i8042 port, irq 0 64 12 x

MOD - sfr 311 > [7,852993] mouse: PS/2 mouse to common mechanism for all mice

MOD - sfr 312 > [7,861470] 00:01 rtc_cmos: RTC may wake from S4

MOD - sfr 313 > [7.864335] input: keyboard to translate the value 2 as/devices/platform/i8042/seri

MOD - sfr 314 > o0/entry/entry 1

MOD - sfr 315 > [7,865148] 00:01 rtc_cmos: RTC database: registered rtc_cmos as rtc0

MOD - sfr 316 > rtc0 [7.865148]: alerts until one day, 114 bytes nvram, hpet IRQ

MOD - sfr 317 > i2c/dev entries driver [7.865929]

MOD - sfr 318 > md [7.867791]: raid1 personality registered for level 1

MOD - sfr 319 > device - map [7.880892]: ioctl: 4.14.0 - ioctl (2008-04-23) initialized: dm - dev

MOD - sfr 320 > [email protected] / * /

MOD - sfr 321 > [7.885043] cpuidle: using Governor ladder

MOD - sfr 322 > [7.887189] cpuidle: using the menu of Governor

MOD - sfr 323 > [7.889424] no iBFT detected.

MOD - sfr 324 > [7.907995] usbcore: registered new interface driver hiddev

MOD - sfr 325 > [7.912219] usbcore: registered new interface driver usbhid

MOD - sfr 326 > usbhid [7.914857]: kernel v2.6 HID Driver

MOD - sfr 327 > [7.918409] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11

MOD - sfr 328 > [7.920969] 0000:00:04.0 virtio-pci: PCI INT A-> link [LNKD]-> GSI 11 (level,

329 mod - SFR > high)-> IRQ 11

MOD - sfr 330 > [7.927488] ACPI: PCI Interrupt Link [INKA] enabled at IRQ 10

MOD - sfr 331 > [7.930856] 0000:00:05.0 virtio-pci: PCI INT A-> link [INKA]-> GSI (level 10,

332 mod - SFR > high)-> IRQ 10

MOD - sfr 333 > [7.938651] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11

MOD - sfr 334 > [7.942086] 0000:00:07.0 virtio-pci: PCI INT A-> link [LNKC]-> GSI 11 (level,

335 mod - SFR > high)-> IRQ 11

MOD - sfr 336 > vda [7.948686]: vda1 vda2 vda3< vda5="" vda6="" vda7="">

MOD - sfr 337 > [7.964043] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.

MOD - sfr 338 > [7.973312] list of devices ALSA:

MOD - sfr 339 > [7.974949] No soundcards found.

MOD - sfr 340 > [7,976759] Netfilter messages via NETLINK v0.30.

MOD - sfr 341 > [7.979604] nf_conntrack version 0.5.0 (16384 buckets, max 65536)

MOD - sfr 342 > [7.983256] ctnetlink v0.93: registration with nfnetlink.

MOD - sfr 343 > IPv4 [7.987257] pilot in IPv4 tunneling

MOD - sfr 344 > ip_tables [7,991258]: (C) 2000-2006 Netfilter Core Team

MOD - sfr 345 > [7.993887] registered TCP cubic

MOD - sfr 346 > [7.995714] socket of netlink XFRM initialization

MOD - sfr 347 > [7.999255] NET: registered to the family of protocols 10

MOD - sfr 348 > [8.003264] lo: disabled Privacy Extensions

MOD - sfr 349 > tunl0 [8.007258]: disabled Privacy Extensions

MOD - sfr 350 > ip6_tables [8,011258]: (C) 2000-2006 Netfilter Core Team

MOD - sfr 351 > [8.014386] IPv6 over IPv4 tunnel driver

MOD - sfr 352 > sit0 [8.017431]: disabled Privacy Extensions

MOD - sfr 353 > [8.021257] NET: registered protocol family 17

MOD - sfr 354 > CPP [8.025256]: registered udp transport module.

MOD - sfr 355 > CPP [8.026916]: registered tcp transport module.

MOD - sfr 356 > taskstats registered [8,031108] version 1

MOD - sfr 357 > [8.125760] input: ImExPS/2 generic explore Mouse as/devices/platform/i8042/s

MOD - sfr 358 > erio1/entry/input2

MOD - sfr 359 > [9,543210] queries send DHCP and RARP, OK

MOD - sfr 360 > [10.161328] IP-Config: 0.0.0.0 DHCP response, my address is 192.168.10.1

MOD - sfr 361 > 01

MOD - sfr 362 > [10.173277] IP-Config: complete:

MOD - sfr 363 > device [10.175341] = eth1, addr = 192.168.10.101, mask = 255.255.255.0 gw = 192,1

MOD - sfr 364 > 68.10.2.

MOD - sfr 365 > host [10.179964] = 192.168.10.101 = domain, nis-domain = (none).

MOD - sfr 366 > [10.183083] bootserver = 0.0.0.0, rootserver = 0.0.0.0, rootpath =

MOD - sfr 367 > [10.186725] release of kernel memory used: 544 k released

MOD - sfr 368 > INIT: initialization version 2.86

MOD - sfr 369 > [10.446791] version 124 udevd began

MOD - sfr 370 > please wait: start...

MOD - sfr 371 > climb: already mounted or busy/sys sysfs

MOD - sfr 372 > mount: according to mtab, sysfs is already mounted on/sys

MOD - sfr 373 > starting udev, udev [10.949268]: renamed cplane eth0 network interface

MOD - sfr 374 > [10.962321] end_request: i/o error, dev fd0, sector 0

MOD - sfr 375 > udev [10.979259]: renamed eth1 eth0 network interface

MOD - sfr 376 > [11.535307] end_request: i/o error, dev fd0, sector 0

MOD - sfr 377 > INIT: enter run level: 5

MOD - sfr 378 > boot OpenBSD Secure Shell Server: sshd

MOD - sfr 379 > generating ssh RSA key...

MOD - sfr 380 > generating ssh DSA key...

MOD - sfr 381 > fact.

MOD - 382 LICO > demon from Advanced Configuration and Power Interface: acpid.

MOD - sfr 383 > acpid: commissioning with proc fs

MOD - sfr 384 > acpid: opendir(/etc/acpi/events): no such file or directory

MOD - sfr 385 > starting Busybox inetd: inetd... done.

MOD - sfr 386 > starting ntpd: fact

MOD - sfr 387 > starting syslogd/klogd: fact

MOD - sfr 388 >

Services Cisco FirePOWER 5.4.1 boot image

ASA - FP # sh mod sfr

Model serial number of map mod

---- -------------------------------------------- ------------------ -----------

SFR unknown n/a JAD192502N6

MAC mod Fw Sw Version Version Version Hw address range

---- --------------------------------- ------------ ------------ ---------------

SFR 80e0.1d7d.53bb to 80e0.1d7d.53bb / o

The Application name of the SSM status Version of the Application of SSM mod

---- ------------------------------ ---------------- --------------------------

Data on the State of mod aircraft compatibility status

---- ------------------ --------------------- -------------

SFR recover not Applicable

Which is expected. Then you must:
```
 session sfr console
```
.. .and then login (admin / Admin123).

You should get a prompt like:
```
 asasfr-boot>
```
Run "setup" but to "bootstrap" basic settings (ip address, host name, etc.) on the partially initialized module.

Then, install the system software image using the system command:
```
 asasfr-boot> system install [noconfirm] url
```
Include the noconfirm option if you do not respond to the confirmation messages. Use an HTTP, HTTPS or FTP URL; If a user name and password are required, you will be asked for them. the URL must include the package (pkg) with the complete picture of SFR installation package.

When the installation is complete, the system reboots. Allow or more than 10 minutes for the installation of the application component and fire ASA services start.

The output of the show module sfr command should also show up to all processes.

Filtering in Cisco ASA using module sfr Web

Hello

I have Cisco ASA 5515-x version 9.2 (2) and I use ASDM version 7.2 (2). I module 5.3.1 LICO of ASA. I want to activate the ASA web filtering feature. Previously, I used the method of expression regex in the SAA to perform url filtering, but it was not effective. Since then, I have the license for the management of firesight I want to use it.

But I am confused as some cisco docs say to set the firesight management in vmware while others offer to run the boot image in the SAA itself. What is the right way to do it?

The show module command, I see that my module of sfr is in place so that means the sfr module is pre-installed, and I can't do a lot of configurations?

It would be better for me to run ASA itself, but if it does not work like that then I will configure in VM. So please me clearify that concerns my options and my best chance.

If it should be installed on a virtual machine or ASA itself, then please give me the link to download the boot images and other files on cisco.com. I have the user name and password, but did not find the correct software.

Thank you in advance.

Your ASA 5515-x performs the minimum version required to support the fire power module (sfr). The module also runs the initial version of the software of the firepower for ASA-based module firepower.

With this combination of Software ASA and firepower on your device, you will need to use an external administrator of firepower to manage module (create strategies, apply licenses, monitor events etc.).

From ASA 9.5 (1) and firepower 6.0, you have the opportunity to make the most of the same functions via ASDM. You must upgrade the ASA (both ASDM) and firepower to achieve module.

In both cases, you should Protect licenses and URL filtering for the module of firepower.

The Quick Start Guide is here: http://www.cisco.com/c/en/us/td/docs/security/asa/quick_start/sfr/firepo...

See also the excellent vidoe Lab Minutes guides for firepower: http://labminutes.com/video/sec/ASA%20FirePower

The ASA and ASDM software is here:

https://software.Cisco.com/download/type.html?mdfid=284143128&flowid=31442

Software module of firepower is here:

https://software.Cisco.com/download/release.html?mdfid=286271171&flowid=...

To run the power of fire management center VM, the software is here:

https://software.Cisco.com/download/release.html?mdfid=286259687&flowid=...

All the links above require a username cisco.com entitled (support agreement) to download the software.

In regard to the centre of defence and module SFR

I have installed in my virtual machine DC. The DC and the SFR module are both in version 5.4. At the time of purchase, I was told that DC is used to monitor the ASA. We bought the license for unit 2, which means I can monitor up to 2 of my DC ASA. I wonder if the domain controller is used only for purpose of filtering and monitoring newspapers. If possible, I want to have the ACL, NAT and the general everying thing ASA through this domain controller so that I don't have to connect to the device 2 all the time. Is it still possible? I use ASA 5515 - x version 9.2.2 and ASDM 7.2 and I don't have the ASDM firesight management access so I use DC separately. Thank you in advance.

Hello diomande,.

Understand you the purpose of the use of Firesight is not correct. Firesight Management Center is only used to monitor managed devices under him such as devices of fire power or firepower software modules integrated with the ASA firewall. You can control or manage your ASA firewall by using the domain controller (Firesight Management). To manage the ASA, you must use the ASDM.

Since you have an ASA, using the firepower of software module, you can inspect traffic selected in your environment. Create an access list and you specify the traffic you need to redirect through the module of firepower.

Select and evaluate if this helps.

Concerning

Jetsy

HA for firepower Modules END ASA 5585 x - SSP 40

Hello

I have a question.

With two Cisco 5585 - X PHC-40 in multi-contexte mode. Both the ASA firewalls are already configured for failover for high availability. What is the configuration of the firepower Modules get high availability if a module of firepower in one of the ASA falls down.

Thank you

Ravi

Failover of the SAA will happen, because with the default service configuration module is monitored as part of the failover condition.

Which can be changed via "no monitor-service-interface module" SAA - the command turns off service module monitoring and, if the module fails, it will not trigger the failover.

Firepower and WINscp - how to get the files module SFR

Is anyone able to use WINscp to get a file to a module of sourcefire? I think that WinSCP has problems with the admin user do not enter expert mode by default.

I have a windows environment and can not get the secure copy scp to work of SFR command to a server with port 22 open windows.

You are right. Sourcefire module/sensor is not as SCP server you cannot use the winSC is there to connect. But it acts as a client PCS, so you can use firesight or any other SCP server and copy the files to the CPS server first and then use winscp to get out.

For example.

> expert

> sudo scp/var/common/leader-to-be-copied [email protected] / * /-IP: / var/tmp

This will copy the file to the directory/var/tmp in firesight. You can use any other SCP server as well.

Rate if helps.

Yogesh

Cisco Module SFR HA speaking

I will implement a Sourcefire solution over the next few weeks and I am familiar with the installation process on a single module. However, I will be installing the module on a pair of active / standby. Each will be framed or installation of SFR need is the own unique IP address? I guess Yes since Firesight will have to separately manage to maintain duplicate, but wanted to check it's the case.

Yes - separate management addresses. They are separate devices in the center of FireSIGHT, each requiring its own licenses.

We usually put them in a group of devices in FireSIGHT for ease of management. Alone, they don't know about the other and don't share any configuration or flow.

OSPF - stuck in init/drother

I can't get the OSPF adjacency between the GSS and a LDR. Any help is very appreciated.
-of the GSS, the output of 'show ip ospf nei' shows the LDR as a neighbour, but the State is init/drother
-train the LDR, the output of 'show ip ospf nei' shows nothing.
-of the GSS, the output of "debug ip ospf" shows the packets hello being sent and received
-of the LDR, the output of "debug ip ospf" shows packets hello sent, but not received.
-of the GSS, the output of ' debug display interface vNic_1 package - vv "shows the ESG (172.16.254.1) by sending packets hello which include the LDR (172.16.254.2) in the list of neighbor...
-of the GSS, the output of ' debug display interface vNic_2 package - vv "shows to the GSS packets (172.16.254.1) hello incoming, but adjacency is never implemented
Environment:
NSX 6.1.1
Interface internal GSS, the uplink LDR and LDR management are all on the same logical switch.
OSPF: the Protocol address is set LDR IP management and the pass on the address is set to the IP of uplink LDR
Transport area extends to the esxi clusters

> LDR uplink and the management of LDR are all on the same logical switch

Please remove the IP address of the management interface of the DLR...

Update module power of fire ASA 5.4.0

Hi all

It looks like Cisco released version 5.4 SourceFire for ASA a few days ago. We Commission a new ASA firewall with SFR module and I would have updated to the latest version before that he go to the prod, more 5.4 seems to have SSL decryption features that are not available in point 5.3.

I can download updates to the center of the defense (5.4.0 and 5.4.0.1), but when I go to Downloads\NextGen firewalls\ASA with SFR etc, I can only see the 5.4.0.1 patch (file .sh) but nothing like it 5.4.0. I don't know how real works upgrade module SFR, but assuming it's the same process as the DC updates are not noncommutative.

I tried to download the update of the SFR 5.4.0.1 module to DC but he said: there is no compatible devices found, and that the update is scheduled for 5.4.0+. Of course my modules are still running 5.3.

Is it just me or is missing required update in the download area on Cisco.com?

Appreciate all the information.
Stan.

Download it here

http://uploads.Sourcefire.com/download/0642eee330b34f40adb63efed43198d6/20150222012033-Cisco_Network_Sensor_Upgrade-5.4.0-763.sh

Transfer to firesight then install, then install the patch

Configure the module of firepower ASA IP address

Hello

today I tried to configure the IP address of the late ASA power module. But unfortunately I failed. The firewall is in the direction of the situation and also do have not any router on the LAN. So, I stop the management interface and configure the IP of firepower on the network server management. But unfortunately I can not ping the gateway IP address that is actually one of the interface of the firewall. It is the series x 5525 firewall. So this isn't a any interface dedicated to management of firepower. It would be nice to know where I made the mistake? I recharge and recovery of the module and I consider the State as always state of recovery. So my question is looking for there is a problem with the module itself?

Module status

SH module

Model serial number of map mod
---- -------------------------------------------- ------------------ -----------
0 ASA 5525 - X with SW, GE, 1 GE Mgmt, AC 8 data
IPS unknown n/a
cxsc unknown n/a
SFR unknown n/a

MAC mod Fw Sw Version Version Version Hw address range
---- --------------------------------- ------------ ------------ ---------------
0 f 1.0 2.1(9)8 9.2(3)
ips N/A N/A
cxsc N/A N/A
sfr N/A N/A

The Application name of the SSM status Version of the Application of SSM mod
---- ------------------------------ ---------------- --------------------------
IPS unknown current Image number does not apply
cxsc unknown No. current Image does not apply

Data on the State of mod aircraft compatibility status
---- ------------------ --------------------- -------------
0 to Sys does not apply
IPS does not is not Applicable
cxsc does not not Applicable
SFR recover not Applicable

Config firewall Interface

#Interface IP-Address OK? Method State Protocol
GigabitEthernet0/0 10.101.106.115 YES CONFIG upward upwards
GigabitEthernet0/1 10.106.106.115 YES CONFIG upward upwards
GigabitEthernet0/2 10.103.254.254 YES CONFIG upward upwards
GigabitEthernet0/3 10.0.210.254 YES CONFIG upward upwards
GigabitEthernet0/4 10.100.254.254 YES CONFIG upward upwards
GigabitEthernet0/5 10.107.253.115 YES CONFIG upward upwards

#interface GigabitEthernet0/1
Speed 1000
full duplex
nameif Server
security-level 70
IP 10.106.106.115 255.255.0.0

Fire power management configuration

Host name: 1 Swiss francs
Configuration Management Interface

Configuration IPv4: static
IP address: 10.106.251.253
Network mask: 255.255.0.0
Gateway: 10.106.106.115

IPv6 configuration: Stateless autoconfiguration

Configuration of DNS:
Domain: XXX.local
Search:
XXX.local
DNS server:
10.101.251.2
10.201.251.2

Any help will be greatly appreciated.

Thank you

Sari

Sari,

Even if there is not a physical module services fire power management port, it uses Management0/0 port to connect to the module of SFR. If you like on the same VLAN as your server VLAN on the SAA plug Management0/0 port on a switch that is sharing the network server VLAN and give the module SFR an IP address on the same subnet.

Make sure that you remove the statement under interface Management0/0 nameif. Here is an example:

interface Management0/0
management only
No nameif
security-level 100
no ip address

Time synchronization between the module of SFR (ASA5512) and the power of fire management center

Hello.

I deploy my network Cisco Management Center (for VMWare, v. 6.0.0) FirePOWER and tie SFR-module of Cisco ASA 5512. After you apply time in CMF settings, I have a synchronization errors for my module SFR ("TimeFor 172.16.x.x synchronization state is out-of-sync").

This article presents a framework that allow the synchronization time SFR-module with CMF. But I don't have an option to set the time on managed devices, just for the CMF.

Please, tell me how I can solve this problem. Thank you!

I just went through this with TAC. They pointed out that the documentation states that you should not synchronize SFR with a virtual CMF. I found myself defining the CMF and SFR as you pull my domain controller, and everything was fine.

How is used to monitor two ASA (active/stby) with modules IPS Cisco MARCH?

Hello

The two ASA with IPS modules are in Active mode / standby. When I try to add both the two IP (active / standby) in MARCH, the MARCH will complain of duplicate names.

How set up in MARCH to monitor the ASA with IPS with topology standby active?

Thank you!

Hello

The fundamental problem with this scenario is that you have modules able non-basculement in a tipping chassis - think of the pair of failover ASA as a device and modules IPS as two completely separate devices.

Then, as we have already mentioned, add only the ASA elementary school. (High school will never be passing traffic in standby mode so it is not really necessary in MARCH) Then, with the first IPS module you can add it as a module of ASA or as a standalone device (MARCH doesn't care). With the second module IPS, the only option is to add it as a separate unit anyway.

In a failover scenario of the SAA swap IP but SPI considering you'll ever messages from ASA active you will get messages from the intellectual property of these two IPS depending on whether you are in the ASA active at the time.

Remember that you must manually reproduce all IPS configuration whenever you make a change.

HTH

Andrew.

Service of ASA module does on 6509-E support remote access VPN?

I'm having a problem of configuration of remote access VPN (SSL, Anyconnect ect.) on the Module of ASA Service on 6509-E. It is even supported or I'm wasting my time trying to do something that won't work in a first place :) to work? Site-to-Site works without any problem.

Technical info:

6509-E current SUP 2 t SY 15.1 (2)

Module of ASA - WS-SVC-ASA-SM1 running of the image - asa912-smp-k8 & asdm-712

Licenses on ASA:

Encryption--Activated

3DES-AES-Encryption - enabled

Thank you for the support.

You run multiple context mode?

If you are, access remote VPN only is not supported in this case:

"Note several context mode only applies to the IKEv2 and IKEv1 site to another and applies not to the AnyConnect, clientless SSL VPN, the legacy Cisco VPN, native VPN client client of Apple, the VPN client from Microsoft or cTCP for IKEv1 IPsec."

Reference.

upgrade of firepower that run in asa integrated

I have a x-5506 running 9.5.1 asa and 5.4.1 sfr.

I have had't used for a while and ran the Manager of the sfr cmd line configuration command. I read that the DB variable for sfr consecutive in a 5506 may be damaged. It seems there because it will not register with my asa now.

If I go to configure > local > register he is stuck on waiting to record. Even on the sfr cmd line.

It is a device that I got through a course less than a year yet. Is that mean that one is not allowed forever to update or download the installation images? can I register to my account?

Hello

When you use Configuration manager to SFR, it expects to sign up to a power of fire aka Defense center management center.

See this article.

http://www.Cisco.com/c/en/us/support/docs/security/firesight-management-...

So once you configure the manager address at sfr, you must complete the registration process in separate Manager as well.

If you are not running a separate management centre, then I believe that you want to manage the ASA and SFR module using ASDM.

You can do this, but for this you don't need configuration manager. So if you do this, remove the handler by using the command "configure Manager delete" and make sure that the computer running ASDM can reach sfr module and vice versa.

See this article to make sure that you are running scenarios.

http://www.Cisco.com/c/en/us/support/docs/security/IPS-sensor-software-v...

See this article for more information on how you can use ASDM to fire module /SFR Power Manager

http://www.Cisco.com/c/en/us/TD/docs/security/firesight/541/firepower-mo...

Rate if this can help.

Yogesh

Configuration and installation of SourceFire ASA

Hello team,

Recently, we have installed the SourceFire ASA-based software but its not in production, but now we intend to get SourceFire ASA production for the management of traffic and URL filtering. Right now, we have the FireSight of installation management system and uploaded image of SFR to ASA. Now ASA will exercise traffic of internet entry/exit point to our network. I have some doubts as follows:

(1) ASA I see sfr module is in place, but what happens if I console module sfr this will affect my normal Internet traffic while I'm in the console of sfr.

(2) are there models of basic configuration for the url filtering to make the job easier.

(3) what are the control list to cross check before get sfr inline module in production.

Thanks in advance for your help.

Thank you - Jadesh

Redirect us traffic to the fire power module using the modular policy framework for something like this:
```
 policy-map global_policy class class-default sfr fail-open service-policy global_policy global
```
Generally, what you do on the console of sfr module do not affect the parent ASA. Until you have the policy to redirect traffic nothing will pass or affect by the module of sfr. As long as you have the 'rescue' the sfr descending module or the reset does not affect production ASA traffic.

Of course once you run traffic through it and start applying policy, you have the option to block or otherwise affect this traffic.

Beyond the user and Admin guides, you can take a glance series Lab Minutes that was done recently. They do a good job of walking your through basic tasks.

Module sfr ASA stuck in init.

Similar Questions

Maybe you are looking for