Monitor loses signal to start Windows

Similar Questions

• I'm running a gateway DX4300 while running the monitor loses signal, etc...

  I'm running a gateway DX4300 while running the monitor loses signal, switch / stop out no computer and computer will not respond unless you unplug the wall.  When you plug the computer into the fans turn on automatically but the computer will not start.

  Hi shermanproffitt,

  Check if the physical connections are connected correctly.

  Try the steps from the following links:

  Frequently asked Questions
  http://support.gateway.com/s/monitor/7005481/7005481faq2.shtml

  Desktop computer - no POST / no video
  http://support.gateway.com/s/checklists/BPC/ck2007050376.shtml

• The monitor loses signal after some time

  During the installation of windows vista, the monitor would lose the signal after some time (the screen turns black and does not) while the computer is still on.  I am currently using ATI radeon hd 5750 and I tried to connect two monitors to the video card and it wouldn't work (both monitors loser of the signal)

  Hi PaulYea,

  1. what type of Installation are you trying? It's an upgrade or clean Installtion?

  2. what happens when you connect to the system now?

  If you attempt an upgrade installation, then try the update the video card drivers and check:

  Update drivers: recommended links

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-drivers-recommended-links

  You can also check out the link to the manufacturer to download the drivers:

  http://support.AMD.com/us/psearch/pages/psearch.aspx?type=2.4.1&product=2.4.1.3.43&ContentType=GPU+download+detail&OSType=Windows+Vista+-+32-bit+Edition&keywords=&items=20

  You can also try running Upgrade Advisor and start the upgrade installation

  Check out the link:

  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

  Note: This also applies to Vista.

  For more information, see the link:

  Solving Windows installation problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Windows-installation-problems

  Hope this information is useful.

• Don't monitor no signal detected after Windows update

  Hello

  I was using my pc and usually I tried to stop my pc but I had to download 1 update of windows required and then managed to download. When I came back all House, I can see is 'no signal detected' I tried to use 3 monitors up to now and always get the same answer.

  Just, I solved my problem out of my video card and replace it again. Thank you Niranjan

• PAGE_FAULT_IN_NONPAGED_AREA error, I can't yet start windows in safe mode, I can't really afford to lose everthing on my laptop

  I get error page_fault_in_nonpaged_area, I can not even to start windows in safe mode, I can't really afford to lose everthing on my laptop, it did not come with any disk, I have not installed new hardware, only the new software is Google Chrome with a few Add-ons for it, laptop Dell with Windows XP Please help

  I don't really know what to do, I can't access the windows at all, please help

  Hello

  To retrieve your documents, you can download a program called knoppix that you can put on a cd. Then boot on this cd. They copy the documents on another device. Here's a link for you help do - option 3

  MyPcHealth - free tools

• If I have to start windows from the disk to do a repair, I lose all my data backed up?

  Computer will not complete boot. Happens to the black screen with green progress bar and stay there. The computer invites me to start from the windows disk. However, if I have to start windows from the disk to do a repair, I lose all my data backed up? Thank you.

  Computer will not complete boot. Happens to the black screen with green progress bar and stay there. The computer invites me to start from the windows disk. However, if I have to start windows from the disk to do a repair, I lose all my data backed up? Thank you.

  Hello

  in Vista, if using a Microsoft Vista DVD(NOT a Manufacturers recovery Disk), the "boot" disk repair process, you ask about, it's only a "Startup Repair", not a repair of the operating system installation; population

  You must have an operational Vista operating system to do a repair installation of the files using a Microsoft DVD of Vista system

  BUT, if the use and start from a manufacturers recovery disk, which guest from the disk is likely to reinstall the OS and lose all your data

  Please explain with more information

• Office stuck in a loop of starting Windows XP restart after changing the map of memory of RAM DDR

  I added that a card of memory DRAM DDR to my CPU ENPower and immediately after my monitor has not received a signal. Then, after reading several articles, I cleaned the CMOS battery, and although he got the monitor works he has also prevented my system to boot with the Windows XP operating system. I've accessed the CMOS utility to change the date/time, nothing helps I still can't get in Windows XP and the user login screen. Now, the system passes through 1 and 2 screens that are part of the commissioning, then lands on the Safe Mode Options screen by which he gets "stuck" not allowing me to select the data options, then it will auto restart every 30 seconds.

  The screen message reads:

  "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this. If your computer stopped responding, restarted unexpectedly or has been automatically closed down to protect your files or folders, select last good known Configuration to return to the most recent settings that worked. If a previos startup attempt was interrupted due to a power failure or because the power or Reset button was pressed, or if you are not sure what caused the problem, choose Start Windows normally. »

  Safe mode

  Safe mode with networking

  Safe mode with command prompt

  Last good known Configuration

  Start Windows normally

  All the these appear on the same screen, but I have no opportunity to select one of them during this mode my pc in.

  What should I do? I need to access the BIOS utility to change the settings of the RAM, or is there something else that I forgot who will be able to get my pc to the top and running properly again?

  Thanks for your advice in advance!

  Remove the memory module that you added.  If the computer can be started without him, then the module is defective or is not compatible with your computer.

• Loss of signal HDMI in Windows Media Center

  I have a Dell Studio Hybrid PCs only running Windows Vista Home Edition Premium attached to a Samsung LN52A750 LCD HDTV via HDMI. If I turn on the TV away from the PC input and back, I lose the video signal... but only when Windows Media Center is running in full screen.

  It works fine:

  1. Turn on the TV.
  2. Switch to PC input on the TV.
  3. Turn on the PC.
  4. Start Windows Media Center.
  5. Turn off the PC.
  6. Turns off the TV (or switch to a different input).

  This also works very well:

  1. Turn on the TV.
  2. Switch to PC input on the TV.
  3. Turn on the PC.
  4. Start Windows Media Center.
  5. Minimize Windows Media Center.
  6. Turn on the TV to a different entry, but leave the PC.
  7. Turn on your TV to the PC - you see always the computer.

  It does NOT work:

  1. Turn on the TV.
  2. Switch to PC input on the TV.
  3. Turn on the PC.
  4. Start Windows Media Center.
  5. Turn on the TV to a different entry, but leave the PC with Windows Media Center in full screen running .
  6. Try to turn on the TV to the PC - no picture or sound is on the screen and the PC must be restarted to return sound/video fully.

  I came across this problem recently (after the passage of a VGA/DVI to HDMI connection). First of all, I came across it when the PC would go to sleep - the video signal stops and the TV stop see the PC signal, even once the PC is awake. I have read a bit online and thought it was something people call a problem of 'EDID handshake. " I thought simply not let the computer sleep (and do not turn off the PC video) would fix it, but I ran into another issue. Kind of a twist.

  I was showing friends how Media Center worked, I spent in the PC, showed them Windows Media Center, spent in a different entry, then switched back to the PC (because I forgot to show you something). The blue background of Media Center appeared for a split second and the signal was instantly lost. I had to reload completely in order to recover the signal.

  I retried the experience - shot to the top of Media Center, active the TV away from the computer, then it passed right away - same result. Restart lost, hard signal.

  I don't know how I fell on it, but at some point, I had the experience with a twist. I pulled to the top of the computer, started Media Center and reduced. Then I moved the TV away from the PC and back... and the signal was always there. I did it again, and again, the signal was there. The TV turns off and on again - signal always there. Then I enlarged Media Center, changed television away from the PC, and when I came back... NO SIGNAL.

  So: with full-screen Media Center loses the signal, but when Media Center is reduced to a minimum the signal remains.

  I started thinking about how my recent use of the Media Center differed from the previous time. Normally, I use the Media Center, watch a movie or something and then go and do something else. I'm back from PC to something else and back. And every time that I had spent in the PC and he had kept the signal, the screen saver has been on - the screen saver 'bubbles '.

  Something that I noticed with the screensaver "Bubbles" is that it sometimes brings the Windows taskbar in the foreground so it 'up' to the Windows Media Center full screen appears. I usually turn the television on the PC input before "wake the computer" and to get the screensaver to go.

  Now I wonder if the lost signal has something to do with Windows Media Center. I have [I think] know a bit the functioning of Windows and the concept of execution of different 'offices '. I wrote a screensaver in C++ unmanaged long ago and I remember there was some crazy stuff that you have to do when you write an application "windowless" (as Media Center - there is no border around it when it goes full screen) and make the "caches", as the screen saver 'bubbles '. I wonder if he has something to do with the standard Windows Desktop works correctly but the Windows Media Center app full screen "desktop" does not properly.

  I tried another experience where I kept full screen WMC, leave the TV losing signal and press Win + D to minimize and show the desktop. Then I went to the TV in the back. No luck - once the signal has been lost, it was lost for good.

  I did since then research various responses. I read that defining the ACPI suspend mode S3 would fix it, but it doesn't. I tried implementing a keyboard shortcut attached to a script that could change the display resolution of 640 x 480 and then change back because I read changing the resolution to update the signal - which did not work.

  Basically, I got no alternative except to keep WMC reduced when it is not in use.

  I'll try to set the screen saver "Bubbles" to 1 minute or something and see if that will at least let me inputs turn on the TV after one minute of inactivity. Yet, it would be good to know if there is some setting I'm missing.

  Hello Travis and Jmelton98,

  Thank you for posting.  Your tests of Travis and additional post of Jmelton, it seems it will be probably something that only can be set by the video card drivers.  If you were to look at the known issues for some drivers, you would see similar questions types.  It is one of the reasons for the drivers for video cards are updated so often.  Sometimes there will be a problem so important that they will release a special patch to fix (like what happened during the crisis game is released).  There should be a new series of pilots soon become availible.

  Please try and see if the problem persists.  Thank you both for the replies that it will help others too. Zack
  Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• I mess with the display option (win + p), monitor losing signal, cannot bring him back.

  At first, I have a monitor, I tried something and end by pressing win + p and change the mode of display for projector only, losing the signal on my screen and can't put back T_T.

  Try win + P several times, it does not work. (A DVI connect to display the map - work).

  Then I stop, reboot, no signal is returned.

  Then I have connected 2 monitors and signal is back, I can change all fashion perfectly. (1 DVI + 1 D - sub - work)

  But, when I remove another monitor signal back to the first step. No signal to monitor. (1 DVI works again - not)

  So now I have to connect Monitor 2 (even if I don't use it) and there is signal monitor, if I remove one, I lose everything.

  Do you have any idea how to fix this annoying problem?

  Fixed it, by removing the cable, put the cable, remove the other insert this one delete and in about 50 times and windows blend and fix it for me * _ *;

• Satellie Pro A300 won't boot up - Manager start Windows Errror

  My Toshiba Satellie Pro A300 for a few months, but now my machine does not start and gives me the following error each time on a black screen.
  I'm under Visa Business:

  * "Cannot start Windows. A recent hardware or software change might be the cause. To solve the problem: *.

  * 1. Insert your Windows installation disc, and then restart your computer *.
  * 2. Choose your language settings, and then click "next."
  * 3. Click on "repair your computer."

  * If you do not have the disk, contact your system administrator or computer manufacturer for assistance
  * File: \Boot\BCD*
  * Status: 0xc000000f *.
  "* Info: an error occurred trying to read the boot configuration data."

  I have not updated or install anything just before that this error has occurred, and I don't want to use the Toshiba recovery disc that came with my laptop, as it will format the hard drive, which is not what I want to do. I can not even in Mode safe mode or anything like that to try to solve this problem.

  Unfortunately I had not round to the creation of the recovery of the DVD in my system itself, think that would allow me to access the recovery console.

  The instructions suggest to insert the Windows recovery disc to try to "fix" the error, but it has not provided with my laptop so what should I do?
  Is it possible to get one from Toshiba or download?

  Any help would be greatly appreciated that this causes me a headache, and I don't want to lose everything already stored.

  Thank you, very much!

  > The instructions suggest to insert the Windows recovery disc to try to "fix" the error, but it has not provided with my laptop so what should I do? Is it possible to get one from Toshiba or download?

  The laptop should be equipped with HARD drive recovery option which would mean you could recover the laptop without any disk.
  Press F8 during the switching on of the laptop. Then choose fix my computer.
  Then choose Toshiba Recovery and launch the installation

  Finally, if the computer starts correctly create the recovery DVDs using the preinstalled Toshiba Recovery Disk Creator.

• Satellite A45-S150 starts windows - safe mode is not possible

  My machine locked upward and when restarted, that asked me to make a selection among several options. Safe mode, safe mode network, prompt mode without failure, recent well known parameters and then just windows. It starts windows in these modes. Any help would be appreciated.

  Brad

  What to say Brad. It seems the full Windows XP operating system has crashed!
  Believe me, something like what is happening simply and I think that it s nothing unusual to anyone who use and works with Windows OS for a long time.

  You should definitely try to reinstall the OS from the Toshiba restore CD.
  But this procedure will format your HARD drive and you will lose all files stored on the HARD drive.

  But this is only one possibility to get Windows running on this laptop.

  Check it out buddy!

• Why does my monitor Samsung SyncMaster B2330 start flashing after a few seconds after that, I was on the computer?

  Why does my monitor Samsung SyncMaster B2330 start flashing after a few seconds after that, I was on the computer?

  Hello

  What operating system do you use?

  Method 1:

  I suggest you check in safe mode.

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Method 2:

  Troubleshoot monitor and video card

  http://Windows.Microsoft.com/en-AU/Windows-Vista/troubleshoot-monitor-and-video-card-problems

  I suggest you to contact Samsung support center and check out.

  http://www.Samsung.com/AE/support/main/supportMain.do

  http://www.samsung.com/ae/support/search/supportSearchModelResult.do?menu=SP00&searchWord=SamsungSyncMasterB2330monitor&default_searchInputBox_value=Enter+model+number+or+keywords&searchInputBox=+Samsung+SyncMaster+B2330+monitor+

• My desktop icons are flashing very quickly whenever I start Windows

  I used the Scanner Microsoft to scan my computer because my Norton was not picking up anything because I knew that something was wrong (Yes Norton is up to date). The Microsoft Safety Scanner picked up 4 Trojan horses and he said that it had removed the. Usually, icons glitter automactically office if I simply click on the desktop and don't stop until I click on the bar tasks. I clicked on the desktop after that viruses have been filed to see if that was the problem and flicker more. I thought that I had finally fixed my computer until I turned on today and after Windows starts he has started making new flicker. I also tried the system restore, and he said that it was not successful. If it wasn't the virus that was causing it, so what?

  P.S. I'm running on Windows Vista SP2 and I'm not sure of the brand or model of my monitor, but I know it's the driver that he has "Dell ST2210 (analog)" and the driver who is the graphics cards is "ATI Radeon HD 4350". My computer is a Dell Studio 540 and it is a desktop computer.

  Hello

  1. do you have the question persists in clean boot mode?

  2 - is the screen flickers or icons on the screen flickers?

  Method 1:

  If the screen flickers, try changing the refresh rate of the monitor

  Flicker of the correct monitor (refresh rate)

  http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

  Method 2:

  If the problem is not resolved, I suggest to create a new user account and check if the problem persists.

  Create a user profile.

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  If the new user profile resolves the problem, you can fix the corrupted profile.

  Reference:

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

• Cannot start Windows Vista

  Hello

  My laptop or laptop has a good light blue screen after a few setting for the display to external display was made by me.

  I tried to play a movie from my laptop to my samsung 40 tv monitor. It does not automatically detect monitor cable is plugged.

  Windows has stopped working probably because changed my setting to 16-bit to 32-bit screen...?

  What should I do in this case?

  Thank you

  Patrick

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  See you soon.

• Failed to start windows recovery

  Compaq cq56-115dx. This is my sencond attempt to try to do a system restore with the HP recovery discs, I just got. Recovery starts with a message "loading files". Then, I get a message "starting windows." And, that's all. Two hours later the windows icon is always on the screen and nothing else happens. I tried several times and each time it hangs on the windows splash screen. For information on the first original attempt to perform the recovery, I was actually quite successful and made it through all three discs. I got a message to restart the computer to complete the installation. When I did the reboot I got an error message that windows cannot restart and I needed to redo the installation. I don't remember the exact wording. I guess I could have gotten a bad file or something and frustrated to lose several hours, I started the second recovery attempt. Now, as mentioned, I'm just hung up on the 'starting windows' screen Before the takeover, the computer was running. Now it won't start, message "windows couldn't start.

  I removed the battery and unplugged the computer for about 5 minutes. Tried recovery, and it does not work as it should now. Not sure why it works now, but he did.  I tried at least six times before that, and he continued to cling on the gray screen.