Motherboard replacement suggestions

Similar Questions

• VSA cluster host to have the motherboard replaced including integrated NIC. The traps?

  Hello

  One of the hosts of our cluster is to have the motherboard replaced on Monday. The fault is the idrac, the host is always more or less of work and remained in production until then

  I fear that the network interfaces integrated on MB are used for the VSA and HA clustering will be modified. What I have to do preparatory work with regard to this, or any config after swap before returning the system back into production after the swap?

  We have 5.1 VSA running on Esxi 5.5

  Thank you

  PIP.

  Ok

  VMware back advising me that as long as the replacement warranty is a Board of Directors of the specification the same then there is no problem and no post necessary config replacement.

  Edge arrived yesterday and everything worked beautifully after the swap. The only thing I had to do was to connect the ports I had put in place previously.

  Thank you

• laptop, needs motherboard replacement, subsequently, I, again, would be able, who, access to and use, the CS, Master, collection, previously installed?

  Computer laptop with already installed CS6 Master Collection needs a new motherboard replacement. Access to use the software, it would be better to go ahead and replace the motherboard? Or, remove the hard drive and reinstall on another laptop? Initially, I bought the laptop with all the pre-loaded software.

  You will be able to reinstall the software as long as you have the serial number needed to activate.  You should check with the company that sold the machine if they did not support installation with it.  The downloads are available through https://helpx.adobe.com/download-install.html

• HP Pavilion HPE h8 - 1380t CTO: compatibility problems, ask questions about knitting-by-turn or possible motherboard replacement.

  I recently baught an EVGA GTX 1060, as this 630 became quite long in the tooth and I thought that I would try to future proof myself a little as the rest of my components seem to be working very well.  However, I can't get the map to work correctly on this particular computer.  Oddly enough, I can get past that screen startup finally after several short beeps and let it sit, but it takes fowever to reach the office and clearly is not executed properly that the resolution is wobbly and software from Nvidia cannot even detect the card.  I guess I had got this far because of the onboard graphics of some sort, but AFAIK this motherboard which lacks.

  I know that the card works fine as I tested it in my other Tower, so I struggled to find a solution.  So far, it seems that the problem is most likely the motherboard, as HP does not have a new BIOS for it since the beginning of 2013 (which I did go ahead and install it).  If true, I find myself with either two options, it seems that the ditch system, entirely or find a motherboard that works with all my old components.  I'd rather not have to empty this workaholic, when all other parts work great, if it is not a work around I would like to know if there are motherboards I could pass that would work with the rest of my components.  Normally I would not bother with even apply for, but I hear a lot of chatter on HP PCs pre-constructed having compatibility problems.

  I bought this computer there is in the case of four years that I would be able to update as I do with any other PC, but I didn't know at the time that HP has a tendency to not update the BIOS settings for anything beyond a year which I admit is incredibly frustrating.  What is done is done however, and I want to make this work without having to clear the entire system.

  Desktop HP Pavilion HPE h8 - 1380t CTO

  Model #: B4J28AV
  Serial number: 2MD2290502

  Motherboard: 2ACE "Pittsburgh" Pegatron Corporation

  Processor: Intel Core i7 3820 3,60 GHz 'Sandy Bridge - E.

  RAM: 10 GB of DDR3 memory

  GPU (stock): Nvidia GeForce GT 630 (this is replaced by the EVGA GTX 1060)

  @Faver, welcome to the forum.

  Your problem is the BIOS.  However, it is because the 1060 GTX requires UEFI in the motherboard instead of a standard/Legacy BIOS.  HP didn't start using UEFI until mid-October 2012.  The BIOS may not be upgraded in the UEFI.  The last cards only not for UEFI were the GTX 660/670.

  MSI made cards with a switch that can be used with a Legacy BIOS or UEFI.  If you decide to go this way, you must contact their Technical Support to help them choose the best card for your system.

  The upgrade of the motherboard can be a problem.  HP has taken advice their specifications.  Therefore, they are not necessarily the same as the commercial versions.  Please make sure that the holes in the motherboard matches the accessory in the case.  In addition, some members have had problems with the connectors in the connections case before, for example, the power button.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• Motherboard (motherboard) replacement should I order for my laptop to LW174UA #ABA?

  I'm looking to replace the motherboard of my HP dv7-6135dx laptop and simply does not know what motherboard I have to buy to replace? I did a search and most sites recommend 659094-001board, but Im not sure because my PC comes with the graphics card ATI Mobility Radeon HD 6490 m and 659094-001 is equipped with the 6770 apparently... Please if I could get some good feedback, I'll be able to order the right part and get this thing working again!

  It's your Board of Directors:

  For use only with the computer models equipped from 6490 chipset and an Intel Dual Core (including the 1024 MB memory discrete graphics subsystem) 639390-001

  Here is the Service Manual:

  Manual

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• After the motherboard replacement Tecra S2 does not start

  Hello

  I replaced the motherboard in my Tecra S2 and now it does not start, the power light is on but nothing on the screen. I can hear the h/d running DVD lights.
  I tried to remove the RAM.
  Also checked the CPU and still nothing.

  NEED HELP.

  Are you sure that the display is OK and correctly connected?
  Is busy, I mean drive HARD HDD LED flashes?

• Pavilion 500-164: motherboard replacement raises Questions

  
  

  Thanks, Malygris1, for your very comprehensive answer.  Unfortunately, I'm looking forward and installed the new Board of Directors.  For those faced with replacing a motherboard HP, I will elaborate on my trip.  The most important step was in buying for the motherboard.  I have no HP, but from a dealer on Ebay.  I DID, however, carefully note the model of the motherboard AND the designated HP part number of alternatives on a small paper on the motherboard label.  The same motherboard model is used in several models of HP Office; but, if the number of HP spare parts is matched, the info on the model should be on the motherboard.

  My original problems were solved with the installation of the new Council.  After a router struck by lightning, the ethernet port had stopped working, and when told to stop, or in standby mode, the machine would invariably restart.  The new motherboard solved both problems, which seem to be related to the power surge.

  I installed the new Board of Directors of the Windows 10 updated 500-164 and held my breath I have it powered for the first time.  I was pleasantly surprised to see that everything looked the same as when I left it.  Recognized support assistant the new Board of Directors as part of a desktop computer 500-164.  I have not tried; but I hope that the recovery media will work, if necessary.  Malygris1, do you think that if Support Assistant recognizes the info on the model, the recovery disks will work?  I'm curious to know how it works, but, if not, no big deal, as I now have a new image Acronis 10 Windows installation, which works perfectly on the 500-164 Pavilion (without "Pitfalls", as some have reported with audio, etc. of the wireless card.).

  My second concern was whether or not Windows is always activated with the installation of the new Council.  He said that he "Windows is not activated.  ... Rats and other profanity.  I know it can take time to be put in correspondence with the info from Microsoft, so I updated the bios and checked the rest of the ports for the features of the machine.  I returned in configuration/system Panel and he told me that the activation information were "unavailable" - different from the message 'not active' sooner.  I've been waiting on this screen for a few minutes and the message changed to "Windows is activated"!  I was ready to make Microsoft telephone activation and I had run a keyfinder to get the original MS product key for Windows 8 from the hard drive, but I didn't have to use both methods.

  So, in summary, if you want a card mother 'replacement', shop for the exact number of spare parts HP; not only the MFG part number.  It will save you a lot of grief.  Obviously, if you want to 'upgrade' from your motherboard, all bets are off, because it's a totally different scenario with different issues to deal with.  My project was a complete success at a cost of $103 for the new motherboard and several hours of my time.

• Satellite C660-15R motherboard replacement question

  I C660-15r laptop and the motherboard no longer works, the reference is the - 6841p.
  I saw one for sale.

  My question is if I buy this record, it will be in being all problems if so what will be the questions please.

  Someone did he do not any other compatible with this laptop motherboards also and if so what are the part numbers, thanks a lot,

  Well, the laptop card mother replacement isn t easy. Its more complicated such as on desktop computers.
  First of all its really difficult to disassemble the whole laptop and on the other hand; After the replacement of the motherboard the DMI string must be updated.

  The DMI code is programmed in each motherboard and the DMI string contains information about the cell phone as; Serial number, model number, etc.

  Without this update, some software requiring such information might not work properly. Also, the laptop recovery is not possible.

  This is why this should be replaced by a mobile technician.

  > As someone not of any other motherboards compatible with this laptop and if so what are the part numbers, thank you very much
  You must use the motherboard published for series Satellite A660.
  Don t think another motherboard is compatible.

• Satellite P100-434 - graphics card gone will be the motherboard replaced?

  Hello!

  Last night, on my laptop screen went black on reboot, but the rest of the laptop seems to load very well. First of all, I thought it was the light back who had died, but an external monitor did not work either, so my son thinks that the graphics card is dead.

  The laptop is almost three years, but, fortunately, it is still under an extended warranty. My question is, repair the laptop, no doubt, replace the motherboard or is not cost-effective and that they will give me a new laptop? Also, how time Toshiba take to repair laptops under warranty?

  Thank you for everything hep.

  Emily

  Hello

  Of course, if the graphics card is faulty, you will get a new mainboard, and due to the extended warranty, it will be free for you. You will not get a new laptop, only the motherboard will be exchanged I think because it s cheaper as a new laptop and Satellite P100 is pretty portable. ;)

  I think that no one can say how long the repair takes to your laptop. It's always different and depending on the availability of spare parts. Therefore, you should ask the authorized service provider. They can tell you more.

  But I have to say on my laptop, that the motherboard was also exchanged the ASP. Repair didn t take much time, as far as I know it was only a few days. Nice service and the technician are cool people. :)

• HP Pavilion dv7-6c63nr: PAvilion dv7 motherboard replacement

  Hello

  I've had my HP Pavilion stored long. A few days ago I tried to turn it on: when I plugged in the charger and the Power button, it turned on for a second but a spark came out of the base of the laptop and recognized this classic a smell of burning plastic. No matter what I did, the laptop does not start or respond to a door.

  After watching carefully and research, I came to the conclusion that the motherboard has been damaged in sévery (he had burned).

  I was wondering how much it cost me to get a replacementet for the motherboard, or if it can be fixed. I know this laptop is a bit old, but it's a great model and brand new and I want to know if it is reasonable to make it work again.

  Thank you!

  Hello @Marceloed6,

  Welcome to the Forums of HP Support!

  I stumbled upon your post on the issue with the motherboard and wanted to help!

  If you are comfortable with the process, you can try to replace the system board using the following guide: HP Pavilion dv7 Notebook PC - Maintenance and Service of Guide

  (Chapter 4, Page 81-85).

  You can get the parts from here: HP parts store

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Qosmio G10: Question about motherboard replacement

  I bought the G10 around 2 years there are in the United Kingdom and who now live in New Zealand.

  I would say it has been a faithful companion, but looking back it cost much to get anything done, because of the ridiculous prices of the FSA.

  I experienced a power supply, two hard drives, my touch pad no longer works and now the GPU (graphics card) is dead.

  I'm sure that most of the people on this forum knows, that is, replacing the motherboard because it is on board.

  I am out of warranty and replacement cost is more than a qosmio second hand of the same age.

  Having done a lot of research on the internet about it.
  I found out that Toshiba US will free of charge replace the motherboard. I asked Toshiba AUS/NZ and they refused him, that it was not a problem.

  Toshiba UK/Europe does, or is it just the Toshiba US that cares about its customers?

  [Edited by: admin on 20-Sep-2007 07:11]

  Hello

  It's very sad to hear that! :(
  I want to share my knowledge on the Toshiba us and Europe.
  As I know the Toshiba us has nothing to do with Toshiba Europe or Australia/New Zealand.
  Portable computers designed for the American market are simply different and also supports different parts and numbers; for example the Qosmio G10 or G20 are not available in the United States but only the Qosmio G15 or G25, etc.

  If you have problems with your hardware, you must contact the partner service manager authorized in your country for further assistance.

  Regarding your question.
  Yes, it really looks like a malfunction of the GPU (graphic processor unit). This graphics chip is fixed on the plateau and in the majority of cases, the whole Board needs to be replaced!
  As you know, these hardware problems could still happen because the new age books are of the high-end products that work always with high performance.
  That s nothing unusual.

  I bought a year ago from G20 and I bought an extended warranty on avoid such troubles.
  So, I always recommend buying the extended warranty in the future.

  Good luck and best regards

• Satellite A60E-672: do I need to new OS after new motherboard replacement?

  Hello

  I was wondering if anyone can tell me if I need to buy a new copy of Windows XP, if I change the motherboard?

  I guess the laptop will be version Toshiba OEM XP and XP security then considered a different laptop and prevent the operation!

  Also where can I get a new card mother (and at what price) for a Satellite A60E-672 valves. V000040780?

  I'm trying just any price on fixing or stripping options and sell as bits!

  Thanks Jon.

  Hello

  > I was wondering if anyone can tell me if I need to buy a new copy of Windows XP, if I change the motherboard?

  If you want to use the same card, you can use the CD recovery with no problems.

  But if you replace the table with different that you will need to buy an original Windows OS. To my eyes the Toshiba Recovery CD will not work.
  Why? Because the image on the restore CD contains all Toshiba tools, drivers, and utilities and this preinstalled different application like utility chipset, graphics driver, etc. could not be compatible with the new motherboard and possibly you will not be able to install the recovery CD.

  > where can I get a new card of mother
  You can order the new Board of Directors of the ASP in your country or you will check the Ebay for a part of second hand

• I need an exact search for my DV7 motherboard replacement

  My HP Pavilion DV7 laptop had its motherboard damaged earlier and needs it replaced.

  Is it possible to get a motherboard for this laptop?

  Product #: QD984UAR #ABA

  Thank you

  Also would make me really happy if you could include the reference number or a link instead of a manual or something.

  Thanks again

  Hello

  You can find all THE parts for your machine at the following link:

  http://PartSurfer.HP.com/search.aspx?type=prod&SearchText=QD984UAR

  Kind regards.

• 17 - e066nr HP Pavilion Notebook Laptop motherboard replacement

  I just replaced the motherboard on laptop HP Pavilion e066nr 17, and during startup, I get an error saying the the serial number, model number and product number is not recognized.  Is it possible to get this information?  I tried to get into the BIOS, but it won't let me change the info.

  Hello

  In this case, you will need to call the HP technical support: 800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number.
  
   http://www.HP.com/cgi-bin/hpsupport/index.pl

  They will help you.

  Kind regards.

• Pavilion dv6 1110ax motherboard replacement

  Hello

  Recently my 1110ax BIOS corrupted and m unable to get by any way mrntioned on the forums.

  Key combinations don't work not and this USB STICK.

  Now the service center guys say that the motherboard has problem and must be replaced. which I doubt completely.

  Is that what someone can say if I can keeping my existing AMD turion processor & card graphics ATI radeon 1 GB to save cost.

  And is it possible to upgrade the processor and graphics card.

  I had been using this laptop for 5 years now and really don't want to give up on this...

  Receive no response.

  You can save the processor and the memory and the hard drive, but the video is part of the motherboard. The processor you have is:

  AMD Turion RM-74 2.2 GHz with 2 MB of L2 cache

  It's the fastest that can be installed:

  AMD Turion™ ZM-87, 2.4 GHz with 2 MB of L2 cache

  A ZM-87 is about $40 on eBay and I'll tell you that it is not worth it for a ghz upgrade.2.

  Radeon 1 GB video is upscale for the dv6-1000 series, so there is no better mother/video card.

  It's the motherboard:

  509450 001

  It is a good deal at $78 for the Board of Directors:

  http://www.eBay.com/ITM/HP-Pavilion-DV6-1000-series-AMD-laptop-motherboard-509450-001-good-USA-/370931290463?PT=motherboards&hash=item565d3a515f

  If it's 'the Answer' please click on "accept as Solution to help others find.