Multicast traffic stops flowing after a while when using IGMP snooping

Similar Questions

• Acer w3-810: heating problem & touch stops working after a while.

  1 year warranty, 810, Acer w3 expired, the Tablet is showing heating questions now, close the camera back and after a while to the touch stops working, touch works fine on reboot and compressed is cold. When the Tablet is connected to a network to the touch stopped working earlier than when not connected.

  to solve this problem:-J' I reset the windows. which increased the length of time in which the touch works but always to the touch stops working after a while.

  I disassembled the Tablet and found that the part that is overheating is memory [h9tknnnbpdma].

  What shoul I do, what I need to change the digitizer, software or any better solution?

  resolved:

  the problem was solved when I disconnected the cables of the digitizer and then reconnected.

• Tecra M2: sound system stops working after a while

  Hello

  I used my TECRA M2 a year without serious problems. A moth started it my problems with audio - after the start (no matter if via boot or wake up from hibernation) his (speakers) system is functioning normally. After a while (several tens of minutes, hours) sound system stops working (no sound from your speakers or headphones). No errors appear, but not sound. When you try to adjust the volume via the Windows icon on the bar the task CPU usage becomes very high.

  I decided to reinstall my M2 - the first attempt was clean install of WinXP SP2 standard support - sound problem has not changed. Today I decided to restore the system recovery CD, but the result is the same :-(

  Any idea? -I suppose that problem Council... Now, I made a mistake when entering - beeps system (such a beep as during startup) - interesting :-/

  Except sound problem - another strange thing - when I send my XP to restart in about 10% of the attempts he goes off and does not start. Starts normally after pressing power button...

  Any ideas would be much appreciated
  TX

  Hello

  Looks like a hardware malfunction.
  Maybe it s caused by overheating.
  Check the cooling modules and try to clean it with the vacuum cleaner.

  If it doesn t help you should contact the Toshiba ASP.

• Keyboard and mouse either fail to start or stops working after a while.

  Original title: keyboard and mouse problem

  My keyboard and mouse either do not work at startup, stop working after awhile, sometimes after a few hours or sometimers causing me to push the button Reset to get out every 10 minutes is on the line of support from microsoft for two hours, cost me £65, but still not fixed

  Pentium I5 dual core 2 x 500 GB disks 5700 chart logitec gaming mouse and keyboard

  Hello

  Thanks for those tips, I've considered that everything that had happened in the last weeks and remembered that my mouse was the first to show signs of problems when the red light on the bottom went dark and brilliant then a few times.

  I swapped the front mouse with a type Wireless and it seems not however solve the problem since replacing it with a different mouse to lead the problem disappeared. In my view, that the old mouse has a hardware problem that shorted supplies USB causing both mouse and keyboard stop working.

  allowed for a few days, so I guess that was the problem.

  Thank you for your support

  Chris

• Pavilion: How can I stop the screen size change when using mouse pad

  I continue to adjust the size of the screen inadvertently when using the mouse pad - how to turn off this feature?

  Hello

  You can change this as follows.

  Open windows control panel and on the top right, next to the display by: select "large icons".  In the new page layout, select the entry of Synaptics.

  The option you're looking for is called "Pinch Zoom" - see image below.  Remove the checkmark against this article, click on close in this window, then apply then Ok in the previous window to save this change.

  

  Kind regards

  DP - K

• FF 8 stops downloading after 15 minutes when you don't surf not actively on the net at the same time. What can I do?

  Everything works fine except when downloading more large packets of data. Se is not a problem, but when I let the computer itself, downloads stop after a short time. FF8 and Internet still work. Never had this problem with previous versions. Help, please. I really don't like to spend hours in front of the computer, clicking every few minutes on an internet page just so that downloads are not interrupted.

  Create a new profile as a test to see if your profile is the source of the problems.

  See "basic troubleshooting: a new profile:

  • https://support.Mozilla.com/kb/basic+troubleshooting#w_8-make-a-new-profile

  There may be extensions and plugins installed by default in a new profile, so check that in "tools > Modules > Extensions & Plugins" in case there are still problems.

  If this new profile works then you can transfer files from the old profile to the new profile, but make sure not to copy corrupted files.

  See:

  • http://KB.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

  It is possible that your antivirus software is corrupt downloaded files or otherwise interfere with the download of files by Firefox.
  
  Try disabling analysis in real time (live) files in your software anti-virus temporarily to see if that makes working download.

  See "Antivirus disable in Firefox preferences - Windows."

  • http://KB.mozillazine.org/Unable_to_save_or_download_files

• laptop computer becomes slow after a while of use and when the charger is connected, becomes normal.

  Hello

  I use HP Compaq Presario CQ62, Windows 7 Ultimate 32 bit OS, 4 GB ram, Intel core i5 processor. It is a portable 4 year old. The battery was changed 8 months ago.

  Now, coming to the problem, my laptop will work very well for a few minutes at the start when I turn it on. After some time, the laptop everything becomes so slow it takes forever to work. This occurs when the power is not connected. If I connect power, less than a minute it starts to work faster. But the laptop would become very hot.

  This problem started when I updated my iPod. After update iPod, I had this problem even while the charger is plugged. Later, I changed the OS Win7 Home premium genuine to Win 7 Ultimate. (Pirates). I have run the genuine Antivirus, cleaned the registry and everything. The problem persists. Please help me with this topic.

  Thanks in advance

  -Kere

  kaaranjikere,

  So I checked the error you are getting, and it is not the battery do not, it is the power which is a failure and that includes everything for the power.

  So it is likely that something wrong with your motherboard.

  You will need to take the system to someone looking over everything.

  I would like to know how everything goes

  Nice day.

• Windows live messenger stops working after a while

  Whenever I connect Windows live I get a message that this communication platform on-line Windows has stopped working and windows will close the program and I am started mid convo quickly. I do not know why this happens, I just reformat my computer and had to reinstall windows and have this problem since. I even tried to uninstall and reinstall new but no luck. Help, please!

  Hello AshNight,

  You should post in the Windows Live help as Mick has suggested. They will come back with help.

  However, in the meantime, you can do a repair on your own.
  Have you installed programs before this problem started? This may include antivirus, e-mail programs, etc.
  I've seen some posts where some products Antivirus and cause of conflict. So as a troubleshooting step, remove your antivirus (not just disable) and see if there is a conflict with your AntiVirus and Windows Live messenger. (Do not forget and don't go out when you do not have an antivirus installed on intenet).

  If that doesn't help, then do a clean boot and see if there is a conflict. You disable all startup items and services of third parties at boot. This method will help us determine if this issue is caused by a loader program or service.

  KB 929135 - how to solve a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  I hope this helps.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• LifeCam Cinema stops working after a while

  -Very well, so I have the camera is plugged in and its detected with the drivers installed and so on. When I start using it, it will work for a good 5 to 10 minutes then stop working and the computer unplug chim will ring and his is no longer detected by my computer for an hour or so he comes back...

  I'm using windows 7 64 x an idea?

  Hello

  (1) don't you make changes to the computer until the problem occurred?

  I suggest you to follow the steps below and check if it helps:

  Method 1: Try to run the hardware troubleshooter and check what the problem is and fix it accordingly.

  Follow the link below a convenience store opened.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  I suggest to return the item and try to run the troubleshooter and check if it helps.

  Tips for solving common driver problems:

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

  See also:

  Automatically get recommended drivers and updates for your hardware:

  http://Windows.Microsoft.com/en-us/Windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware

  Hope this information is useful.

• USB 2.0 to VGA device stops working after a while, reconnected works again

  I tried without success to use this device to connect my second monitor.  It works for half an hour, give or take and then nothing.  I unplugg and plug in my lap and he does it again, and I repeat the cycle until what I got too frustrated.  I go into devices and it shows all of my devices do not work correctly, but this is not the case.  I returned a cable and got a new one, but the problem persists.  Anyone else having this problem until I disconnect everything and walk to the center of Micro.

  Hello

  • Is what type of camera?
  • If you use a different USB port it works?
  • Are these USB ports on the USB powered monitor?

  Please answer back with more information that helps us better understand the issue.

  In the meantime, I suggest you perform a clean boot and see if the problem still occurs in the clean boot state.

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• Audio stops working after a while

  The audio of my Hp envy 6 t-1000 (windows 8) stopsworking after awhile.  The audio comes back if I restart the laptop. I tried to reinstall the drivers updated and final audio but problem stays. Any help is appreciated.

  Hello

  Try the following.

  Open windows control panel, open Windows Update, select "View update history" in the left pane and then select "Installed updates" link in the next window.

  Locate the KB2962407 update, right click and choose uninstall.  Once completed, restart the computer, open windows control panel, open Windows Update and select "Check for updates".  You will see the update that you have uninstalled just offered once again - right click and select "Hide update".

  After that you may or may not need to remove and reload the sound driver - if you do, how to use Recovery Manager to reinstall the drivers and software is detailed in the document at the link below.

  Recovery Manager - Windows 8.

  Kind regards

  DP - K

• Illustrator CC crashes after a while of use.

  Hi, I just downloaded the suite yesterday and thought I would try HAVE today. I can open the program without problem. Open files, create files and work on them, then save them along the way. Then after about 10 minutes, it freezes. I can't click on anything, only the close button. I have the auto save set at all hours, so I don't think it's a matter of economics. I also don't think it's a matter of file size because if I have a blank page open and do nothing for the document, the result is the same. I'm after update to my way of thinking of graphics card that was where the problem was, but the result is always the same. My Task Manager indicates that the memory used when I am clicking on suite with illustrator is about 25%, including chromium used in the background.

  I am at a loss, I can't seem to find solutions online or other queries that seem to correspond to what is happening. Any help will be appreciated.

  I'm working on windows 8 by the way.

  Thanks in advance!

  There are several Chrome addons that will interfere with the AI. Alternatively, you can have software security such as Webroot or some security password that is causing problems.

• How to stop the generation FND_USER.customer_id when using LDAPUserImport

  When a user is created in the form of 'set the user' R12.1.3, no customer_id is created in the fnd_user table.
  
  When a user is created using LDAPUserImport (from a ldfiwrite against OID), the customer_id is filled.
  
  How to stop the generation customer_id when you import users in R12?
  
  I tried to disable all these events business (except the last 2), but not of joy:
  
  People with DISABILITIES Oracle Trading Community oracle.apps.ar.hz.CustAccount.create
  People with DISABILITIES Oracle Trading Community oracle.apps.ar.hz.CustAccountRole.create
  People with DISABILITIES Oracle Trading Community oracle.apps.ar.hz.CustAcctRelate.create
  People with DISABILITIES Oracle Trading Community oracle.apps.ar.hz.CustAcctSite.create
  People with DISABILITIES Oracle Trading Community oracle.apps.ar.hz.CustAcctSiteUse.create
  People with DISABILITIES Oracle Trading Community oracle.apps.ar.hz.CustProfileAmt.create
  People with DISABILITIES Oracle Trading Community oracle.apps.ar.hz.CustomerProfile.create
  ACTIVE Trading of Oracle community oracle.apps.ar.hz.OrgCustBO.create
  ACTIVE Trading of Oracle community oracle.apps.ar.hz.PersonCustBO.create
  
  
  (For OrgCustBO.create and PersonCustBO.create, the status field is fixed... cannot change)
  
  All advice appreciated.
  
  Thank you

  Hello

  Pdf linked in document 261914.1 utility MOS LDAPUserImport has a parameter named - tcaRecord
  which takes either y or N as parameter (is default).
  I guess that if you fill in this parameter with N, no record CAW (customer) will be created...

  Concerning

• Dreamweaver seems to stop to update original file when using "Manage Site"

  I am developing a lot of web project, and I'm using localhost.

  To separate, I use the function to manage the Site on Dreamweaver CS6.

  But when I open the file using Windows Explorer, I got my old version of the code. And when I open the same file using Dreamweaver I got my latest work.

  This is the first time occur. before works well

  And yet one thing, always when I open Dreamweaver CS6 several hours, my CPU fan is so loud, it will be fine again when closing Dreamweaver.

  Thank you

  Agree with the statement of what Murray...

  However, you have explained on an error...

  I realize this problem when sending to the real server and received the error

  Do you remember the exact error message?

  Check the settings of your site server. It is same as defined by you at the first time when the definition of the site.

  Try the Site cache recreate: select your site > Site Menu > advanced > recreate Site Cache.

  In addition, you can also try re-creating the preferences of DW. Backup you old preferences on the desktop before recreating them.
  http://kb2.Adobe.com/CPS/839/cpsid_83912.html

• Computer stops automatically while you use.

  Original title: my calculation will stop automatically without any warning when using... makes me a lot of trouble and it always the case please tell me solution.

  my computer off as someone power remove the battery...

  It gives no warning and just nearby.

  Please give solid solution for it.

  Hello Salman,

  Check the event viewer for the detailed error message and send us the Event viewer log file:

  http://msdn.Microsoft.com/en-us/library/aa189531 (v = office. 10) .aspx

  http://TechNet.Microsoft.com/en-us/library/aa997769 (v = exchg.65) .aspx

  Use SkyDrive download collected files and post screen/image capture