My computer beeps every seconds 18-20

Similar Questions

• Windows 7-3 beeps every 30 seconds while logged in (not around the screen of the Bios, not connecting)

  After that I connect to Windows 7, I hear 3 rapid beeps every 30 seconds. It does not go far, i.e. it is not a time of presence and repeat indefinitely. I ran Diagnostics through bios and see anything there (no hardware problems). If you cut the speakers it disappears is not an internal part, like the motherboard. Any help would be greatly appreciated.

  Hi Mark,

  I appreciate the efforts to try to solve the problem. Please write us with the following details.

  What is the brand and model of your computer?

  As you mentioned that you do not receive this sound, after turning off the speakers, it seems to be a problem caused by any process running in the background. I suggest you to open Task Manager and check the process running in the background. If you find any suspicious process just try to put an end to this process.

  You can also try to check the cause to the clean boot.  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135

  Note: Please refer to the section: How to reset the computer to start normally after a boot minimum troubleshooting section of Kb to start the computer to a normal startup after you fix the problem.

  Write to us at the State of the question. We will help you

• A beep every minute on computer, how to stop it

  I had a virus. Microsoft took control of my computer and me a scan of 10 hours.  Computer works fine now, except there is a beep every minute.  How can I stop it please.

  Hi NuCarCarrier,
   
  The system beeps are so important and it will indicate system errors and it will warn you against system damage. When the processor system or Random Access Memory (RAM) or hard drive is not working properly, it will give the alert system using the beep.
   
  Therefore, I recommend you to check the good condition of functioning of your RAM and hard drive.
   
  Change the Windows sound scheme has been defined as 'None'.
   
  Follow these steps to do the same thing:
   
  a. to open sounds and Audio devices, click Start, click Control Panel, click sounds, speech and Audio devicesand then click sounds and Audio devices.
  b. on the tab sounds , in the program events list, select "No. sounds" under sound scheme, click on Save as.
  (c) in the dialog box Save the scheme under , type a name for the new sound scheme.
   
  The new scheme appears in the box sound scheme .
   
  Check if you are still having the tone.
   
  For more information, see:
  To create a sound scheme

• Computer hangs every 30 seconds in all programs

  My computer freezes every 30 seconds.  Sound stutters and hesitates the cursor.  Freeze only lasts for 1 second, but this is very embarrassing.  It happens in all programs and at all times.  I have tried several programs fix - it as advanced system of cleaning and difficulty cleaning without result.  I downloaded process Explorer and it shows my use of cpu amounting to a normal 7 to 20 percent when the stuttering occurs.
  I have a Dell Studio XPS 9000
  Intel Core i7-920 processor
  8 mb L3 cache clocked at 2.66 ghz
  8 GB SDRAM DDR3 at 1 066 mhz
  ATI Radeon HD 4350 w / 512 MB
  Windows 7 Home premium 64-bit

  This started about 2 months ago and drives me crazy.  Any help will be much appreciated.  I really don't want to go through the trouble of reinstalling windows 7.

  Original title: freeze momentary

  Hello

  Check with Support from Dell, their online documentation, drivers, diagnostics and ask questions in the forums on
  known problems.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/

  =========

  Use the startup clean and other methods to try to determine the cause of and eliminate problems.

  ---------------------------------------------------------------

  References to Vista also apply to Windows 7.

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Try these to erase corruption and missing/damaged file system repair or replacement.

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or
  Windows 7
  http://support.Microsoft.com/kb/929135

  Use advanced tools to solve performance problems in Windows 7
  http://www.howtogeek.com/HOWTO/6152/use-advanced-tools-to-troubleshoot-performance-problems-in-Windows-7/

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/default.aspx/GP/slow_windows_performance?p=1

  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to change, add or remove startup programs in Windows 7
  http://www.SevenForums.com/tutorials/1401-startup-programs-change.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Think about it an absolute must - manually update your drivers.

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods
  above is preferred so that the latest drivers from the manufacturer of system and device manufacturers are
  found)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
  Ultimate and Enterprise)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Pavilion h8 - 1070t: blocked on the HP splash screen, computer beep

  I just installed a PSU Corsair CX600 and an EVGA GeForce gt 740.

  When I start my PC, is rest on the start screen and beeps once, every ten seconds. After 3 beeps (30 seconds) my PC beeps again followed three quick beeps and the monitor stops receiving signal from the computer (I do not see the HP splash screen, no signal).

  What could be the problem?

  I think that your problem is that the video card is not compatible with your BIOS.  EVGA 700 series cards require UEFI in the motherboard instead of a standard BIOS.  I suggest you to contact EVGA Tech Support (1-888-880-3842) to see if they have a VBIOS update that will allow the card to work with your computer.  If they do not have an update that they can email it to you.  Tell them that someone of the HP Forums suggested that you call.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• How can I stop my Officejet Pro 8600 one beep every hour on the hour...

  HP Officejet Pro 8600 works very well but the hourly beep is very annoying.

  Hello The_Majar,

  Welcome to the HP Forums!

  I understand that your Officejet 8600 beeps every hour. I will do my best to help you! Please make sure that the printer is connected to a live wall, not a surge protector. I recommend this step, that the printer can not get enough power.

  Then, try to reset the printer for more information, then 60 seconds.

  Please post your results, I'll be looking forward to hear from you.

• My HP Pavilion starts in Preset Mode and the sign flashes every second

  When I start the computer the next sign appears:

  Mode Info - 48.4 KHz / 60. OHz - 1024 x 768 - PRE-SELECTION MODE.

  The sign is flashing every second and doesn't go away.  I'm unable to log in because the sign covered the opening of session space programs.

  Definition of a restore point has not solved the problem. Help!

  Hello S.JColcombe,

  When you start your computer you are able to see your Windows operating system boot, before the screen flickers with the information you provided above?

  I suggest you to check the connection between the computer and the monitor. Or is it a laptop?

  http://support.Microsoft.com/kb/555375

  Thank you

  James

• a beep, then 4 beeps per second and no startup EXP 8700

  Hi all

  I have an EXP8700 running 10 64-bit windows. Do you have the W10 last updated and the computer was working fine.

  Today, I tried to start. I get a signal, a break, then about 4 beeps per second going on forever!

  I tried another keyboard, but not chance I try to hit F2 F10 or F12 and cant' get out beeps

  Suggestions?

  Kind regards

  Mike

  What is a "EXP?" 8700? Do you mean 8700 XPS?

  Try to clear the BIOS:

  1. Power off, unplug
  2. Power button press / hold for about 15 seconds
  3. Open the case and remove the motherboard battery
  4. Power button press / hold for about 30 seconds
  5. (Reinstalling all the RAM, if is not currently installed)
  6. Replace the battery and case
  7. See if it boots with only mouse, screen and keyboard connected

• 3 beeps, 5 seconds silence, 3 beeps, etc change the memory did not help...

  Mac Mini end of 2012 running El Capitan

  With 3 beeps, 5 seconds silence, 3 beeps, etc, it's "no good bank."  I was using crucial memory, works fine until about a week ago when he is awakened from his sleep gave the order to 3 beeps.  Changed to original memory of apple, same, got crucial replacement memory, same 3 beeps...  I doubt that all the 3 series were / are bad.  What else could be?  Any hardware problem would give sequence 3 beeps?

  Probably the logic board is having some problems caused by the bad memory or another problem. I would certainly get extract in an Apple Store or service provider.

• Satellite A300-1IW: HARD drive access light blinks every second

  Hello everyone, and sorry for the English, I'm french :)

  I bought a Satellite A300-1IW a few days and suddenly (don't remember exactly when) early light access HARD drive blinks every second and it continues even after several reboots!

  It does so only with Vista; I checked the disk with 'diskmon' activity and I saw that even if it was * no. * disk * written * or * reading * the led continues flashing, so I think that it is not bound to certain services of vista (superfetch, indexing...)

  A similar problem, I saw on a Microsoft support, but it was under windows 98 and with old motherborads!
  See: link: [http://support.microsoft.com/kb/138598]

  So it seems that it is related to level Vista SCSI or DVD...

  I have now is not critical, but it's annoying to have this led flashes all the time

  You have an idea? Don't you think that it could be related to bios? I want to be sure before touching it, because it is always tricky.

  Thanks for your help

  In my opinion, nobody can offer no comment because you already gave the answer. There is nothing unusual and certainly no reason to panic.

  What do about it? What you want to do? Sorry, but this is a really stupid question. I can just offer you a stupid answer. ;) Take black tape and curl up the LED. ;)

• At startup, the computer beeps very - Compaq Presario s # 31316953

  I bought a Compaq Presario s3310 om (2600 + amd athlon with XP Home Edition.) S # 31316953)

  When I start the computer the computer beeps continiously and nothing happens after that. I did some research and would like to confirm that it is a RAM problem. The original Ram has 512 MB of ddr sdram memory. I did a search on the diagnosis Compaq Bios Beep codes and a beep very indicates error memory - reinstall or replace and re test. I'm on the right track?

  Nothing is lost by air, dust off the RAM slots.  Not sure you interpretation of the beep codes are correct.

  Beep codes: http://support.hp.com/us-en/document/bph07107

  What is more troublesome is buying a vintage 2003-04 machine that did not work. In addition, reinstall all the other cards.

  You can also try a system recovery not destructive http://support.hp.com/us-en/document/c00007689

• Qosmio G50 - HARD drive blinks every second

  Well, if she's here,

  I have a Qosmio G50. I installed WindowXP Pro 64-bit.

  I noticed the hard drive light flashes every second. I spent some time searching the net for a soultion. This led me to download a utility called "process explorer" from microsoft.

  This utility show me that the active process is services.exe. The properties of this service suggest that it handles "eventlog" and 'plugplay '.

  I realize that I can't go to the event log, nor what I want.

  Can anyone help?

  Thanks in advance.

  Hello

  The HDD led always flashes if it read all the data or written to the HARD disk.
  The service.exe (Service Control Manager) belongs to the Windows operating system and it s of Microsoft which is necessary and my knowledge background process, it cannot be disabled.

  Good bye

• How to read two files (one updates every second, the other is constant) simoltaneously

  Dear all,

  I'd appreciate if someone help me.

  I want to read two files, one is the temperature that updates every second, and the other is energy hysteresis that has specific lines and is constant.

  I had a program in the discussion forum to read a file as it is updated. I checked this program in my case and it works.

  Then I added playback file hysteresis energy to the existing file. But while I run the program, the energy hysteresis file is read with all the lines.

  But the goal is that every time the updates of the temperature, I need to read a line of the file hysteresis energy.

  in this way every second, so, I have a new temperature data and a row of the other file.

  I tried to use 'for loop' inside the program, but it did not work, because the temperature reading will stop until that end of the loop.

  I joined the program.

  Could someone help me how read only a row of hysteresis energy file every time that the temperature updated?

  IS that what you wanted to achieve?

• minimum Serch in every second

  Hello!

  I use the DAQ Assistant, and I have an analog input channel. I want to find the minimum value of my signal every second. So, I want my vi, to write the minimum value of the last second... (what is understandable?)

  Thus, in the second and a new value.

  How can I do?

  (I use max.vi waveform min (programming-> wave-> Analog Waveform))

  Thank you!

  Use the DAQ Assistant as continuous mode with sample number = frequency for 1 block of data per second.

  After your DAQ Assistant use the Express VI statistics (available in the Signal Analysis) and check Minimum to determine the minimum of your dynamic data.

• How to stop compensation labview my data output by a fixed amount of 0.125 seconds of every second iteration 1?

  How to stop compensation labview my data output by a fixed amount of 0.125 seconds of every second iteration 1? (I have my DAQ Assistant contained in a while loop so that I can control the number of iterations and therefore the time of sampling).

  My apologies for such a badly phrased statement of problem. The question I faced which was the sign that I was getting a pair of accelerometers and through an amp. in my DAQ board felt an offset in voltage for a short period every second iteration 1. It turns out that the problem is that my laptop and the AGP were grounded. Once I disconnected the signal ground in the shift of the signal amp went.

  Thank you for your messages.

  Kevin