my computer shuts down by itself idle, see event log the many different mistakes some cry

Similar Questions

• My Vista computer shuts down by itself

  Only within the last week, my computer began to close. This habit died when I'm trying to play a game that I bought a couple of years back which is on a dvd.

  I made a secure start, ran a program of virus with negative results. When it is in safe mode, the computer turns off, but if I type a document, a little game (card games) or reading e-mail, then it stops. No error message, no blue screen or anything like that, it just stops without warning.

  I said that is my memory (memory defective chip), also, I need to reformat my hard drive that, and also, maybe my video card needs to be replaced and several other interesting ideas. In addition, maybe my diet is perhaps a problem or maybe a software problem

  I clean off the case of my office, a little salty but not bad, using compressed air.

  I also changed my power settings, and that's not good.

  I would be grateful for any help or suggestion.

  Hello

  Could be heat related - try using a small fan to blow into the air intakes to see if that helps.
  It is just like it loses power or stop it in the normal way?

  Remove ALL power and reinstall all the memory cards and cables (both ends where possible).
  in fact, remove and replace - don't do not just tight. Remove the dust bunnies and clean the
  air vents. Check that fans are working (before and after opening the case). When your laptop on all the
  You can do is to reinstall the memory and clean the vents (still may try to add a small fan as a
  test).

  This sounds like material so if the above does not help you then probably need help
  a real computer store (not the leeks and the glances at a Best Buy or other stores) or the
  Support of system Maker.

  ===========================================================

  Check with these utilities to see if information may be collected: run BlueScreenView
  to see if there were any BlueScreens and verify in MyEventViewer at shutdown
  (or a few seconds before) See the event log contains useful information.

  It is an excellent tool for displaying the blue screen error information

  -Free - BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  and displays information about all accidents of a table.
  http://www.NirSoft.NET/utils/blue_screen_view.html

  -------------

  MyEventViewer can be verified at the time of the blue screen (BSOD) or event within a second
  or time of the BSOD or event to provide more information about the possible cause - see TIP.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it a bit before and after the time of the event or BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ------------

  AppCrashView - free - a small utility for Windows Vista and Windows 7 which shows details
  application of all accidents occurred in your system. The information breaks down is extracted from the
  .WER files created by the Windows Error Reporting (WER) of the operating system component of each
  time that an accident has occurred. AppCrashView also allows you to easily record the list of accidents to
  text/html/csv/xml file.
  http://www.NirSoft.NET/utils/app_crash_view.html

  ------------------------------

  Also do this so you can see the probable bluescreens. (You may or may not be able to see
  them if they occur even after doing this according to the cause.)

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  (also Windows 7)
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  =========================================

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  Hope these helps.

• my computer shuts down about 2/3 of the way after that the progress indicator starts and stops... any suggestion as it turns on again?

  Try to update of Itune, update got stuck, I turned to the computer off, impossible to restart... the indicator stops about 2/3 of the way and the computer shuts down again...

  Start Safe Mode removes the system caches that can help.

  Follow these steps to start in safe mode.

  1. Start or restart your Mac.
  2. As soon as you hear the startup tone, hold down the SHIFT key.
  3. Release the SHIFT key when you see the logo Apple appears on the screen.

  After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

  To leave safe mode, restart your computer without pressing any keys during startup.

  Then try to update iTunes.

• My computer shuts down is no longer with button closure

  My computer shuts down is no longer with button closure. Works only with button on the computer case.

  * original title - system update updates microsoft windows *.

  Hello

  1 are there any changes or updates made on the computer?

  2. what operating system is installed on the computer?

  3. what happens when you try to shut down the computer?

  4. do you get an error message? If Yes, what is the full and exact error message?

  Step 1:

  Try restarting your computer in safe mode and check if the problem persists.

  a. restart your computer.

  b. when the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows Advanced Startup Options.

  c. using the arrow keys, select the Safe Mode option.

  d. press the Enter key on your keyboard to start Windows Safe Mode.

  e. when Windows starts, you will be at a typical logon screen. Connect to your computer and Windows goes into safe mode.

  f. check if you still have the problem.

  If it works fine in safe mode try performing a clean boot in order to find the cause root.

  Step 2:

  See the article about how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: when the diagnosis is complete do not forget to reset the computer to a normal startup.

  If the problem is not resolved, please provide more information to help you best.

• My guard computer shut down unexpectedly when I play games.

  My guard computer shut down unexpectedly when I play games. Now it is not always the case, just sometimes. The other day I was playing Sims 3 all day, literally, with the graphics settings maxed out and had no problem. The next day, he would crash as soon as it finished loading, even with the graphics settings at the bottom. Today, it was working fine this morning and now it crashes again. I had the same problem on and off with other games as well, Halo 2, Kings Bounty, UT 3. Here is my system:

  OS - Vista Ultimate 32 bit
  Processor: Core 2 Quad Q9400 @ 2 .66GHz
  RAM - 4 x 1 GB PC6400 DDR2/800
  MB - MSI P7N SLI - FI
  HARD drive - 150 GB x 2 (Raid 0) Raptor 10 k RPM
  PSU - 1000 watts
  GPU - NVidia GeForce 9800GT 1 GB (x 2 in SLI)

  And the error I get from Event Viewer:

  Filter event with the query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace '//./root/CIMV2' because of error 0 x 80041003.» Events cannot be delivered through this filter until the problem is resolved.

  I got the error almost everyday since I got the computer, about 10 months ago, but it only blocks the computer if I play a game. I tried the 'fix' that removes the WMI event viewer 10 error, but everything done was make sure the error is not logged. I also tried another fix I found me delete the files in the repository, but that no longer works. I also run scans of complete system of virus/malware Spybot Search & Destroy and AVG 8 and verified the updated driver for my hardware. I also ran diagnostic tool memory. Who has good/clean/current. Can it be fixed or what I have to reinstall the OS?

  Hi JerHekSr,

  Thank you for using answers Forum.

  The first thing that comes to mind would be to check the motherboard manufacturer for an update of the firmware/BIOS.

  The error message mentions "loadpercentage > 99' which looks like you are running may at maximum load of the CPU while the game and that is the cause of the crash. You could try a clean boot to prevent the using CPU resources while you play to see if it makes a difference of strtup programs.

  To help resolve the error and other messages, you can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts. This article describes how to solve problems in Windows Vista by performing a clean boot. This article also describes how to start the Windows Installer service and how to reset the computer so that it starts as usual.

  Note When you perform a clean boot, you may temporarily lose some functionality. When you start the computer as usual, the function returns. However, you may receive the error message, or you can experience the original behavior.

  If the computer is connected to a network, network policy settings may prevent you from following these steps. We recommend strongly that you do not use System Configuration utility to change startup options on the computer, unless a support engineer Microsoft directs you to do so. This can make the computer unusable.

  a. log in the computer using an account with administrator rights.

  b. click Start collapse this image enlarge this image, type msconfig.exe in the Start Search box and press ENTER to start the System Configuration utility.

  The collapse of this image to this image if you are prompted for an administrator password or for confirmation, type your password or click continue .

  c. under the general tab, click Selective startup , and then clear the Load Startup items check box. (The box use the Boot file is not available.)

  d. on the Services tab, select the hide all Microsoft services check box and then click on disable all .

  Note Following this step lets services Microsoft continue to run. These services include networking, Plug-and-Play, record of events, error reporting, and other services. If you disable these services, you can permanently delete all restore points. Do not do this if you want to use to restore the system with the existing restore points.

  e. click OK , and then click restart .

  Step 2: Enable half the services

  a. follow steps 1a and 1B to start the System Configuration utility.

  b. click on the Services tab and then click to select the hide all Microsoft services check box.

  c. Click to select half of the check boxes in the Service list.

  d. click OK and then click restart .

  Step 3: Determine whether the problem returns

  If the problem persists, repeat steps 1 and 2. In step 2, click to clear half of the check boxes that you have initially enabled in the Service list.

  If the problem does not occur, repeat steps 1 and 2. In step 2, select only half of the remaining check boxes that are cleared in the Service list. Repeat these steps until you have selected all the check boxes.

  If only one service is selected in the list of services , and you the problem persists, the service selected the cause of the problem. Go to step 6. If no service is causing this problem, go to step 4.

  Step 4: Enable half of the startup items

  a. perform a clean boot by repeating step 1.

  b. click on the Startup tab and then click to select half of the check boxes in the startup item list.

  c. click OK , and then click restart .

  Step 5: Determine whether the problem returns

  If the problem persists, repeat steps 1 and 4. In step 4, click to clear half of the check boxes that you have originally selected in the startup item list.

  If the problem does not occur, repeat steps 1 and 4. In step 4, select only half of the remaining check boxes that are cleared in the startup item list. Repeat these steps until you have selected all the check boxes.

  If only one startup item is selected in the startup item list, and you still experience the problem, start selected in the list element is the service that is causing the problem. Go to step 6.

  If no startup item causes this problem, a Microsoft service most likely the cause of the problem. To determine which Microsoft service may be causing the problem, repeat step 1 and step 2 without selecting the hide all Microsoft services check box in each step.

  Step 6: Resolve the problem

  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.

  Step 7: Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  Click on start to reduce this image enlarge this image, type msconfig.exe in the Start Search box and press ENTER.

  The collapse of this image to this image if you are prompted for an administrator password or for confirmation, type your password or click continue .

  On the general tab, click the Normal startup option, and then click OK .

  When you are prompted to restart the computer, click restart .

  I hope this helps. Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• every time that the computer shuts down, (IE Automatic updates), recent documents is empty.

  original title: recent documents: every time that the computer shuts down, (IE Automatic updates), recent documents is empty. How do I prevent this? Very frustrated Ruth

  Recent documents: every time that the computer shuts down, (IE Automatic updates or I turn off during the night) recent documents is empty. How do I prevent this? Don't know if the following has nothing to do with it, but - about 6 months ago I reinstalled XP, since then I have no sound and comes to the foregoing. Oh and to add, at the same time, I've changed hard drives up and down, which means that I have and that he had 2 hard drives.

  Very frustrated Ruth

  Hello

  Try the steps below to solve the problem.

  Caution:

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756

  (a) open the registry editor and navigate to:

  HKEY_CURRENT_USER-Software-Microsoft-Windows-CurrentVersion------Explorer-advanced

  (b) save the key in a file. See the article of support upward.

  (c) the value of Start_ShowRecentDocs as a result.

  (d) value of 0 - list of my documents most recently opened is disabled
  Value 2 - list my most recently open documents is enabled

  Note: set the value to 2.

• My computer shuts down without warning while I play games

  while I play games I see down in the system tray that the internet was disconnected and the few seconds my computer shuts down.

  so when I turn it back on it gives me a minute before he does again.

  again once it does only when I'm playing games and he did not do it now when I play, but after 10 minutes it starts.

  Hello

  Could be heat related - try using a small fan to blow into the air intakes to see if that helps.
  It is just like it loses power or stop it in the normal way?

  Remove ALL power and reinstall all the memory cards and cables (both ends where possible).
  in fact, remove and replace - don't do not just tight. Remove the dust bunnies and clean the
  air vents. Check that fans are working (before and after opening the case). When your laptop on all the
  You can do is to reinstall the memory and clean the vents (still may try to add a small fan as a
  test).

  This sounds like material so if the above does not help you then probably need help
  a real computer store (not the leeks and the glances at a Best Buy or other stores) or the
  Support of system Maker.

  ===========================================================

  Check with these utilities to see if information may be collected: run BlueScreenView
  to see if there were any BlueScreens and verify in MyEventViewer at shutdown
  (or a few seconds before) See the event log contains useful information.

  It is an excellent tool for displaying the blue screen error information

  -Free - BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  and displays information about all accidents of a table.
  http://www.NirSoft.NET/utils/blue_screen_view.html

  -------------

  MyEventViewer can be verified at the time of the blue screen (BSOD) or event within a second
  or time of the BSOD or event to provide more information about the possible cause - see TIP.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it a bit before and after the time of the event or BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ------------

  AppCrashView - free - a small utility for Windows Vista and Windows 7 which shows details
  application of all accidents occurred in your system. The information breaks down is extracted from the
  .WER files created by the Windows Error Reporting (WER) of the operating system component of each
  time that an accident has occurred. AppCrashView also allows you to easily record the list of accidents to
  text/html/csv/xml file.
  http://www.NirSoft.NET/utils/app_crash_view.html

  ------------------------------

  Also do this so you can see the probable bluescreens. (You may or may not be able to see
  them if they occur even after doing this according to the cause.)

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  (also Windows 7)
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  =========================================

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  I hope this helps.

• After running for 1-2 hrs closed windows, not to wait about 5 minutes to turn off turn back on. What can cause my computer shut down

  While on the internet (firefox) after using it for about an hour my computer shuts down automatically for no reason.  I have to wait about 5 minutes to turn back.  During the restoration of my session, I get this message "the script is not responding," if I hit continue Firefox closes running.

  There are several reasons that the PC automatically stops due to the error, usually you would see blue screen and system restart. It could be a hardware or software error. Windows check log and see what the cause was also check problem and solution center and see if something is there. Also update your Windows and run the disk check. Also execute following tool to make sure that your PC is free of malware:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

• Computer shuts down randomly without error message

  My computer shuts down randomly without notice.  I don't get blue screens, etc.  I have a Gateway desktop computer using Vista Home Premium 64-bit, Service Pack 2.  I tried to go to the event viewer, but does not know what it means.  I have attached the event below.  My computer turns off sometimes in 10 minutes, 2 minutes or 2 hours.  It does not matter. Any thoughts?

  Log name: System
  Source: Microsoft-Windows-TBS
  Date: 27/04/2011-17:01:10
  Event ID: 537
  Task category: no
  Level: Information
  Keywords:
  User: LOCAL SERVICE
  Computer: HomeDesktop-PC
  Description:
  Could not find a TPM Module (TPM) security device works on this computer.  TBS could not be started.
  The event XML:
  http://schemas.Microsoft.com/win/2004/08/events/event">
   
     
      537
      0
      4
      0
      0
      0 x 8000000000000000
     
      130006
     
     
      System
      HomeDesktop-PC
     
   
   
   
  

  I realized what it was.  I normally go through, clean the fans and inside on a regular basis.  The fan that is attached to the Central Unit worked.  However, between the processor and the Fan Heatsink was extremely dirty.  It was packed with dirt.  To see this, you need to remove the fan.  He carefully cleaned, and all is well.

  Thanks for the info indicating that windows will usually give you an exception error, and it is probably a hardware problem, dirty, etc.  It's exactly what it was.  I just could not see the dirt without removing the fan.

• Windows live quickcam pro 9000 when try to record vidio computer shut down restart

  Logitech Quickcam pro 9000 v-ubm46 window live... Quick capture... take a picture Yes... When try to record vidio computer shut down & restart

  Window xp pro served pack 2.2002 quickcam v11.8

  Suggestions appreciated thank you for research

  had no any error message the computer just black screen close

  Sorry, the problem is with the Quickcam capture

  Thank you for your help

• error 1321: NTauthority or Services and controller app sez he has a problem and the computer shuts down

  sez no authority trying to run AVG or Malwarebytes - every 1/2 hour or if some "prog system? NTauthority or Services and controller app sez he has a problem and the computer shuts down

  Hello

  • What is the full error message?
  • What were the changes made to nfore this question?
  • What exactly do you mean by "no authority running avg or malwar bytes?
  It's a possibility that there is a startup program that is launched with a command line and it appears.
  You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you have finished troubleshooting, proceed as explained in the article to reset the computer to start as usual.

• How can I configure drive extender? get an error when the computer shuts down say reinstall Extender player

  get an error when the computer shuts down say reinstall Extender player. ? What is it. Thank you

  Hi deener49,

  Please look at the thread below for a possible solution:

  http://answers.Microsoft.com/en-us/IE/Forum/ie7_6-windows_other/please-reinstall-Extender-Player-invalid-or/86692b09-9464-E011-8dfc-68b599b31bf5

• My computer shuts down completely without reason.

  My computer shuts down completely without reason. It only happened in the 2 or 3 months. I have Windows Vista and I need help.

  How to use the System File Checker tool to fix the system files missing or corrupted onWindows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  Click on start / all programs/accessories then
  Right-click on the command prompt option and select "Run as Administrator".
  At the command prompt, enter: SFC/scannow

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• When I try to burn a movie, my computer shuts down. This didn't happen with more short films, but this one is about 84 minutes.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  When I try to burn a movie with videos imported from different sources, the computer shuts down after 10 minutes.

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  limespider wrote:
  When I try to burn a movie, my computer shuts down. This
  didn't happen with more short films, but this one is all
  84 minutes.
  =======================================
  Sounds lke a question of system resources.

  Large, complex projects can cause problems... it can
  be worth a try to create several small projects and save
  each of them in the format .wmv movie to a folder on your hard drive
  drive. When you import clips .wmv collection in DVD
  Machine to each of them becomes a scene (chapter)... you can
  have up to 18 scenes.

  Besides rendering video is time CPU and could
  initially be an overheating problem that could also result in your
  computer to close.

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• my computer shuts down randomly and blue error screen "100000ea".

  Original title: my computer shuts down randomly and blue screen before closing down.

  my computer shuts down randomly and blue screen before closing down.

  the error message is generated after that reboot is:
  Signature of the problem:

  Problem event name: BlueScreen

  OS version: 6.1.7601.2.1.0.768.3

  Locale ID: 1033

  More information about the problem:

  BCCode: 100000ea

  BCP1: FFFFFA800826AA20

  BCP2: 0000000000000000

  BCP3: 0000000000000000

  BCP4: 0000000000000000

  OS version: 6_1_7601

  Service Pack: 1_0

  Product: 768_1

  Files helping to describe the problem:

  C:\Windows\Minidump\071512-98311-01.dmp

  C:\Users\Paras Desai\AppData\Local\Temp\WER-767228-0.sysdata.xml

  Read our privacy statement online:

  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:

  C:\Windows\system32\en-US\erofflps.txt

  Hello

  Blue error screen is mainly related to the driver problem. However, it might be also due to hardware problems. The blue screen error message may or may not contain useful information but the file record of emptying to the smallest set of useful information that may help identify why your computer behaves as such. You can read them by installing the Windows debugging tools and follow the instructions in this article.

  How read partial memory dump files that Windows creates for debugging:

   

  http://support.Microsoft.com/kb/315263

  Note: The article mentioned above also applies to Windows 7 full version.

  Or post the screenshot us for clarity on the issue.

  Consult the following link which contains information about how to download files mindump:

  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

   

   

   

   

  Method 1:

   

  Step 1: Start the computer in Mode safe.

  Reference:

  Start your computer in safe mode:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

   

  Step 2: If you are not faced with the same problem in Mode without failure, you can do a clean boot to eliminate any influence from third parties.

  A clean boot allows you to check if startup item or services to third-party application is causing this issue.

  Reference:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:

  Note: When you're done to diagnose, follow step 7 in the article to start on normal startup.

  Method 2: This error could be due to bad video drivers, video card drivers updated on the Web site of the manufacturer.

  Reference:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3: SFC scanner.

  Reference:

  System File Checker (SFC) scan will replace the missing or corrupted system files on your computer.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7: