My devices connect only to an airport machine

I have two extremes of the airport, which connects to my modem and creates a network and one which runs the network. However, all of my devices are connected to the Airport Extreme that creates the network. What I am doing wrong? They are on different floors of the House and appear to be configured correctly, but the devices that sit on adjacent to the Airport Extreme, extension of the network does not connect to it. I know your supposed to have an Airport Extreme and multiple Airport Express, but we already had the old (4th gen. I think) Airport Extreme, so we decided to use it. Thank you!

There is no difference between express and extreme to extend...

However if you started near the main AE... you must turn off the wireless and then turn it back on... and it needs to connect to the Extender.

Unless you have a problem in the configuration.

Post screenshots of airport utility and we see what happens...

Remember, if the signal is bad for the AE on the upper floor... It can transmit a signal any better than that. So if the client devices connect ok the Repeater is in the wrong place.

Tags: Wireless

Similar Questions

  • What is the effect of the "signature of all other computers or devices?  This remove the software from these machines or simply make it unavailable until this as connected and disconnected (e) other machines used CC on?

    Connect failed

    Impossible to sing in on this computer or device.

    The Adobe ID [email protected] has already been used to activate the software on two other computers or devices.

    0 - retry.  I've already signed out of one of them.

    0 - you sign out all other computers or devices.

    What is the effect of this action? @

    just make it unavailable until this as connected and disconnected (e) other machines used CC on?

    That's exactly what disconnect only. No software is removed or otherwise affected on your computer.

    See error 'activation limit reached' or 'connection failed ' | Adobe products

  • My new airport does not detect my existing WiFi network, I can connect only via the LAN.

    Bought a new airport 1 TB TimeCapsule and I wanted to add to my existing via a WLAN network. It does not detect it and I can connect only via the LAN. What I am doing wrong?

    Unfortunately, unable to connect to a 3rd time Capsule part wireless using a Wi - Fi.

    You need to connect to the time Capsule to your existing modem/router using a wired Ethernet cable connection, permanent... like the Time Capsule Setup Guide illustrates.

    If you really don't want the time Capsule to connect using the wireless... she can do... If it gets a signal to another Apple wireless router. So if you were ready to add another Apple... as an AirPort Extreme router... and connect it to your existing Ethernet cable router/modem and configure AirPort Extreme to broadcast a wireless signal... .then.. .the Time Capsule would be able to connect in this way, assuming that he is where he can receive a good quality of AirPort Extreme wireless signal.

  • Is there a way to see the ip address of the devices connected via the airport?

    Hello world

    Is there a way to see the ip addresses of the devices connected via the airport? I can see the name of the devices but not what ip are they?

    Thanks in advance.

    Open AirPort Utility

    Hold down the option on your Mac so you double-click on the image of the AirPort router

    Wireless clients are displayed

    Click on the small arrow next to each wireless client to see details about the device and the connection

  • EA6500 only shows no device connected to the switch of working group 5 ports

    I just replaced a defective Linksys e4200 with an ea6500.  After assistance by phone, I got to the top and work, but only one computer on my LAN is not displayed.

    I connected an 8 port 10/100 switch Linksys my 4200, and my wife's computer was connected to that.   The computer displays the IP as 192.168.1.133 and it is connected to the internet with my router again.  But the ea6500 does not show a device with the ip address.  Instead, he shows what he calls a network with the IP 192.168.1.130 device.

    How can I see the devices connected to the switch 5 ports and determine which ip addresses, they have been assigned?

    I use a switch with my network with a router EA and it shows the devices correctly. Turn off the computer which does not appear in the list of devices and check to see if any device will appear as offline adter who. Remove from the list of devices, and then restart the router. Once the router is ready, open the page of the router again and turn on the computer and check if it will be detected correctly. I hope this helps.

    Edit: Check and make sure you have the latest firmware loaded. Otherwise, update the firmware and do a reset after the update of the firmware. Check your list of devices after that.

  • Qosmio G50-12 q - how to configure the devices connected to the USB mode standby

    Hello

    I wanted to use the PC sleep function.
    I also wanted to as devices that have been extinguished when in stand by.

    Once implemented this function the PC will regularly stand-by, but the device connected by usb are set on fire, any other master type, a device a usb wi.fi, etc.

    Someone told me that maybe some functions in the Bios only are not put in place to do that once entered the booth by the PC off all devices those connected.

    What checks and I have to perform in the configuration PC bios?

    How we in the bios? By pressing the keys on which?

    Thank you

    * valkyrie @ *.

    Please post comments if workaround posted by Akuma helped!

    It would be really appreciated.

  • Equium P200-1ED is able to power external USB devices connected on it?

    (1) is anyone able to confirm if the Toshiba Equium P200-1ED is capable of powering an external USB device connected to it via one of its 6 USB ports?

    (2) what is the maximum power that the Toshiba Equium P200-1ED can provide only one USB port?

    (3) can the Toshiba Equium P200-1ED providing the power referred to in Question (2) above to each of its 6 USB ports?

    Please don t after several markets on the same subject.
    After you recommend first one:

    http://forums.computers.Toshiba-Europe.com/forums//message.jspa?MessageID=115025#115025

  • M30: Connect only with 42.6 K - how to increase speed

    My M30 connect only with 42.6 K speed. I have try all options to increase the speed, but the success. If anyone has the solution, please send me email to [email protected]

    I try the other series on my telephone line and connect them to the speed of 52 to 54K. Desktop even connect at 54K.

    Hello

    Go to Device Manager and choose the modem. Then do a right click and properties.
    You will find many tabs. Please check if the port of Maximum speed in the Modem tab option is set to the highest value.
    In addition, you can check the button in the Advanced tab settings in Advanced Port the controller must also be on the high (max).

    Please check these possibilities.

    Good bye

  • Satellite A30 does not start with the USB device connected at boot time

    Hello

    I have a Satellite A30 and sometimes it does not start.
    After turning on, not even the BIOS starts.
    even if sometimes the BIOS starts, but the OS does not load.

    I figured out that its related to USB devices connected at boot time.
    If no USB devices are connected, it starts without a problem.
    Even if the start-up is suspended, as soon as you unplug start it BIOS USB devices.
    Its ok to connect USB devices later, once the system has started.
    I disabled "removable devices boot" and "network startup."
    just in case, but it makes no difference.

    BIOS is version the most recent (1.70) and it comes up with all kinds of USB devices.
    printer, mouse and (self-powered) external USB hard disk.

    Is this a known issue?
    There is no known workaround solution?

    Hello

    I put t know why this happens, but it has to do with the BIOS.
    The same thing happened on my old laptop. I couldn't start my unit while the USB printer has been turned on and connected.
    The only solution is to disconnect the external USB device during the boot process.

    RSY you should check if the order of boot in the BIOS has been on the HARD drive first.

  • Irritating device connect/disconnect sounds

    I have a Dell Vostro 1510 laptop with the update to SP3 and XP Professional operating system. While listening to a music CD, I get intermittent device unplug his follow up immediately by the device connect sound. There is no indication of the offending device. What gives?

    Hello

    1. have you made changes on the computer before this problem?
    2 do you find this sound only during playback of music CD?

    Step 1: Search for the issue in the clean boot state.

    From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

    Reference:
    How to configure Windows XP to start in a "clean boot" State
    http://support.Microsoft.com/kb/310353

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
    1. click on Startand then click run.
    2. type msconfigand click OK.

    The System Configuration Utility dialog box appears.

    3. click on the general tab, click Normal Startup - load all device drivers and services and then click OK.
    4. When prompted, click on restart to restart the computer.

    Step 2: Also, look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.

    Reference:
    Using the event viewer
    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_event_viewer.mspx?mfr=true

    Understanding of event viewer
    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/event_overview_01.mspx?mfr=true

    Procedure to view and manage event logs in Event Viewer in Windows XP
    http://support.Microsoft.com/kb/308427

  • Names of the devices connected to the router

    How can I tell the names of the devices that are connected to my router E2000? Cisco connect says I have 4 devices but I only have 3. I'm trying to understand source of the 4 device.

    Open the Cisco connect software. Go to "Setting up the router" and click "Advanced settings". Who will open the router configuration page.

    Click the status tab. Go to the tab "Local network" sub on the button "DHCP Client table". Here is a list of the devices connected to the network.

  • My Sprint HTC Android mobile phone connects with the supplied USB cable, but the computer says 'No HTC Device Connected'

    My Sprint HTC Android mobile phone connects with the USB cable, but the computer says 'No. HTC Device Connected' so I can't sync...

    Hello

    1. do you have HTC Manager installed on the computer?

    2. have you tried it with different USB ports?

    You need the HTC Sync HTC phone Manager software.

    Method 1: Try again with different USB ports and see if that helps.

     

    Method 2: If HTC Sync is installed, if you get the message "no device connected" in HTC Sync, ensure that your phone USB setting is changed to "Charge Only" to "HTC Sync".

    If the methods above do not help, you can contact HTC for additional help.

    Here is the link: http://www.htc.com/us/support/

  • Device connect and disconnect sounds play when NOTHING is connected!

    Hello

    I am running Windows Vista x 32 on my Dell Inspiron 1525. The problem is that the device connect sound, immediately followed by the device disconnect sound, playing intermittently even when not a single device is connected. I have already extracted 1 million solutions online, and here's what we can exclude:

    • Still, she does when no devices are connected, so it is not a loose USB device.
    • Does it by chance; I can't predict when the sounds will play, and there is no evidence in the event viewer I can link to this problem.
    • My laptop does not have Bluetooth, so it's not just trying to pick up a network.
    • I've updated all the drivers I can think and who has been recommended by others. They are all to date. I have also each service pack installed.
    • It is a customized, sound scheme so that these sounds are ONLY related to the device plug or unplug, respectively. I even went through all the sounds in the profile just to make sure I didn't accidentally double up.

    The only other thing relevant I can offer is that I actually just sitting there waiting for the sounds to play while looking at the Device Manager. I got all the closed lists, and when sound plays, the "network adapters" list opens. Yet once, I checked to make sure that all of these drivers are up to date, but it still plays. Please help, I'm going crazy! Thank you in advance!

    BTW, even if I can put up a good show to know what I'm doing with a computer, I'm not that well versed in techno-parler, please dumb down your solutions. Thank you. :-)

    Hello

    That description makes it sound like the issue is a network adapter that is enabled - right click either the
    Interface NETWORK (wired) or peripheral card WiFi and turn OFF - which ever you use and see if the noise persists?
    I look in Device Manager is a good idea.

    Is it a PC or a laptop - card integrated or add-on/in? If a PC off ALL power and remove and reinstall
    all cards and cables on both ends (in fact, remove and replace - do not just tight). Not much, you can
    do this with a laptop, unless WiFi is external but for PC or laptop, you can turn off the edge
    WiFi (if she has that) and use an external device.

    I hope this helps. Rob - bicycle - Mark Twain said it is good.

  • Could not power on VM: no space is available on the device: cannot power on the virtual machine.

    VMware esx ei, 3.5.0 123629

    Physical memory: 64 GB

    Hard drive: 1.63 TB

    7 virtual machines. 5 of them are configured with 4 GB memory and 2 of them with 2 GB of memory. I am able to power on 3 virtual machines with 4 GB of memory.

    When I try to turn on 4th VM with 2 GB of memory, I get this error message "could not power on VM: no space is available on the device: cannot power on VM.»

    I would like to know if this is the limitation of the ESX Server? How should I size the memory for VMS if I want to run every 7 virtual machines to the

    Moreover, given that I have 64 GB of physical memory. Is there documentation that provides a report of the maximum allowed memory configurable

    compared to the virtual memory?

    Thank you

    Ganesh.

    Ganesh,

    Memory reservations are defined based on VM by VM.

    You can allocate more memory to the virtual machines you have in your host (it's not really a good idea to go crazy with the overcommitment of memory, but some level of excessive pressure is used in general).  Memory applied to your VM resources are shares, bookings and VMkernel Swap limits.

    Just to illustrate:

    You allocate 8 GB memory to a virtual computer.  If you take all the parameters by default, ESX will allot a 8 GB VMkernel Swap file in the base directory of your VM (it will have the extension ".vswp") this VMkernel Swap file is a safety net.  Your virtual machine, at this stage, can consume up to 8 GB of memory If physics is available from the host.  If the memory of your host is overcommitted, some of the available memory 8 GB could be allocated on 8 GB VMkernel Swap file.

    If you set a reserve of memory - 2 GB - this means that the vmkernel will still award the first 2 GB of memory used by the virtual machine to the physical memory.  This is not means that the 2 GB of memory reserved is carved off the coast and completely dedicated to the virtual machine.  This means that the vmkernel offers up to 2 GB of RAM to the VM when and if she needs to use it.  It is a guarantee that the memory will be available upon request.  Because of this guarantee of the VMkernel, VMkernel swap file only has to make sure that the 6 GB memory is satisfied (4 GB total less the 2 GB reserved), so the VMkernel Swap file is only 6 GB in size.

    Actions are a mechanism for prioritization and limits are a cap on physical memory ever allocated to the VM.

    You can set up any number of memory for the virtual machines that you want - frankly, overcommitment of memory for ESX is a very good thing, but you must be vigilant about watching your systems if approve you.  If you have 64 GB of RAM, and you only configure your virtual machines to use total 32G, then you lose 32 GB of RAM.  If you allocate, say, 96 GB of RAM (total) to your virtual machines, then you look at a 50% overcommitment.  What to watch in overcommitting memory is application performance (and more importantly - perception of the user of this performance) and also the memory ballooning and VMkernel Swapping activity.  Those who can both will be in graphics performance in VirtualCenter.  I would recommend reading the Guide to management resources for more details.

    Hope that provides an overview.

    Thank you

    -jk

  • Email rec'd 'a device began synchronizing with devices connected to your Firefox account' Please explain

    What is happening with my account of Firefox? I received an email as follows: «a device started syncing with devices connected to your account in Firefox» If there is a security problem, Firefox's history on all my computers. Please explain what is happening here quickly. I think I'll remove the Firefox browser everything and start over with someone else. I can't take risks with my information.

    This isn't a security problem. With the team of Mozilla Sync, I have confirmed that it is an email waiting turning Sync in Firefox on a new computer, tablet or phone. In the future, they will cease to send this type of email to avoid worrying people.

Maybe you are looking for

  • Qosmio F10-136: straps on screen

    HelloQosmio F10-136, I bought three months ago. Yesterday I get problem, only when starting (where is the qosmio logo is appear) of the computer and start the windows I have vertical straps on the screen. I can't install the graphics driver, because

  • Points of beginning and end of a song seems to change at random in the Bounce dialog box

    Even if I put the departure and arrival within the project, when am I going to bounce the project the bounce dialog box displays the numbers of different from what I've specified. Everyone sees what is happening? Using X 10.2.1 Pro logic.

  • The use of multiple keyboards and mice on one computer?

    Is it possible to use separately the two keyboard, mouse and monitor with two operating system simultaneously on a single computer for different purposes?

  • HP g62-340us: install a new motherboard.

    I have a HP G62-340US I work for a friend and would like to get the best motherboard I can to make it as fast as possible and would like to know what would be the best motherboard to get. The product is #: XH066UA #ABA is the serial No.: [Personal In

  • Keep to spooler subsystem app error message.

      I get an error message which announces that windows are closed spool subsystem app for reasons of security sikke, all printers are removed from my computer and it is not possible to install new, Microsoft can fix or should I switch to mac computer