My home button is really hot and stop working

Similar Questions

• Satellite Pro A300D down hot and stops shortly after. Help!

  Hello together,

  3 weeks ago, I bought the Satellite Pro A300D laptop. Since the beginning, I have the problem that the laptop gets hot and stops less than an hour!

  I'm not running any application of high performance and I keep the left side of the free laptop so that the hot air can get away! I already cleaned the heatpipe using a vacuum cleaner.
  It could not be! I need the laptop for work and that it is impossible...
  What can I do? Should I send him?
  Help, I'm grateful

  Frank

  Post edited by: DerVogel

  There could still be dust stuck in the radiator, but you say that its only 3 weeks to dust is unlikely.

  Its under warranty, so take it to a Service Center for repair. This may have the thermal grease refreshed or something.

• My computer freezes and stops working as soon as the antivirus is used.

  Original title: My computer has detected a virus.

  & He is obviously infected by a virus, but now when you run any number of different programs of not doing a full scan is detected. What should I do?
  I rebooted, it about 3 times & the virus survived still reboots.

  It freezes and stops working as soon as the antivirus is used. When you try to reinstall the Virgin keep PC, gets it to halfway through the installation, stop & comes with a blue screen.

  Hello
   
  What is the blue screen error code?
   
  System freeze may be due to viruses or some third party applications. So let us, start your computer by disabling all third-party services and see if it helps.
   
  Method 1:
  Try to perform the clean boot and check if it helps, here is the link:
  http://support.Microsoft.com/kb/929135
   
  Note: When you're done to diagnose, follow step 7 in the article to start on normal startup.
   
  Method 2:
   
  I suggest you make a system full scan just to be sure.
  Here is a link that will give you information on how to perform a full scan of the system:
  http://www.Microsoft.com/security/scanner/en-us/default.aspx
   
  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• How can I move the home button between the front and the address bar?

  Her that I have my firefox put in place over the years is to place the buttons like this:

  [Back] [Front] [Stop/Reload] [Home] [Progress Animation] [Address bar]

  Now in FF29 I'm trying to move the home button between BackForward buttons and the address bar and it won't let me.

  I thought that FF29 was supposed to be the most customizable Firefox yet? * confused *.

  Is there a way to do it, am I missing something? Thank you

  "I thought that FF29 was supposed to be the most customizable Firefox yet?
  
  Who told you that was incorrect, as far as I'm concerned. Firefox is more customizable than the 'competition', but not as much as the previous versions were.

  The home button can be moved, but the back / button drop-down list is set to the address bar - they cannot be separated.

  The combo Stop / Reload button is locked in the address bar.
  
  The 'old' activity indicator has disappeared. Deemed unnecessary with the animation of loading on the left corner of each tab, where the favorite icon once the page is completely loaded.

  https://support.Mozilla.org/en-us/KB/how-to-make-new-Firefox-look-like-old-Firefox

  Many users install the extension Classic theme restaurateur.
  
  https://addons.Mozilla.org/en-us/Firefox/addon/classicthemerestorer/
  But I don't think it will turn out to be along term solution. As users begin to install other extensions, I think they're going to face compatibility issues where the new extension "expects" the user to use what Firefox is come with - not the 'retro' functions

• now, my home button reads "homeButton.label;" and does not work. Help. Thank you...

  I have on my computer, looked up and saw this "homeButton.label"; on my home button.
  I can't get rid of it in tools etc and it does not work as a command. I press to go home, in this case google, but it does nothing. At the bottom left of the page, it simply says 'Done '.
  I am at a loss to explain it.
  Anyone?
  Thank you
  SL

  You have this problem when running in Firefox SafeMode?
  http://support.Mozilla.com/en-us/KB/safe+mode
  Do not choose anything at the moment, just use 'continue in safe mode.

  If this is not the case, see this:
  http://support.Mozilla.com/en-us/KB/troubleshooting+extensions+and+theme...

• RH10. How to make home button on the toolbar and of home in the box "breadcrumbs" link to go to the same location

  (I don't know what the problem is with the editor of these days. Only choice is HTML with tags or this editor who suddenly decided to put my text in italics and not let me remove it! He already let me create line breaks. )

  I use: RoboHelp WebHelp Pro Single Source Layouts, 10 (albeit without using RoboHelp Server).

  I have five SSL, each with their own unique contents. The table of contents for each licensed module includes basic help topics.

  • Basic Help
  • Help for module 1 licensed
  • Help for module 2 license
  • Help for module 3 licensed
  • Help for module 4 licensed

  The default theme using base is "Introduction.htm. The default theme of each licensed module is the theme of introduction for this add-on.

  In the basis of the help by clicking on the button Home in the toolbar opens "Introduction.htm. By clicking on the Home link in the region of breadcrumbs, for example ""Homepage > Management Data Sources > creating a database ", also opens 'Introduction.htm'."

  In a license module, click on the home button in the toolbar opens "Introduction.htm. BUT, by clicking on the Home link in the region of breadcrumbs, for example "Homepage > analysis of the loss, opens the introductory section of the module under license." Our QA group filed a bug against this behavior. They feel that by clicking on the Home button and clicking on the link home takes you to the same place.

  All modules use a common window with a display two-pronged and all the WebHelp Pro buttons, including "home (skin: help NGP)" selected.

  They also use a common skin. The home button properties are: name of the item and the text = "Home". Links of "Introduction.htm" button, with a dependence on "Release\Core\Introduction.htm".

  Is there an easy way to achieve the results expected by the AQ, where clicking on host always opens "Introduction.htm", while authorized opening assistance always opens the introductory topic for the module? DISCLAIMER: I do not know how the script, if it is a possible solution.

  Thank you.

  
  Carol

  LOL, "all this said, the WebHelp Pro has worked quite well without HR server."

  And yet, here you ask about solving a problem, right?

  I think you should study serously ordinary passage to WebHelp. So much more than you report problems with the behavior of the toolbar buttons and the behaviour of the breadcrumbs.

  The reason is that RoboHelp Server maintains some of this aspect when you publish the content out there. So I'm not surprised to see point out you inconsistent behavior with different "modules". I guess it's an installation "merged"?

  See you soon... Rick

• Satellite L350D get hot and stop all of a sudden

  Hello

  I have a Satellite L350D model psle8e now 2 years old I recently met a heat problem (80 to 103 ° C) and stop suddenly.
  I installed SpeedFan 4.43 to increase the speed of my fans he said that all the
  my fans are at 0 RPM (can not control the speed of the fans), I tray to clean it but no effect.

  If anyone has a better solution or recommend a similar software.
  Will be a good help.
  H. E.: WIN 7

  Hello

  I think software is not solution. I put t know how you cleaned your laptop, but you need is professional cleaning. This means: your laptop must be disassembled and cleaned properly.

  After cleaning of cooling and cooling chimneys, grilling your laptop will be cooled properly and you won't have problems with OFF switch.

• adapter iPad got hot then stopped working

  Hello

  I have an iPad Air and used iPhone 5 Watt chargers for charging. But he soon to load that I bought today a 10 Watt adapter (to an authorized Apple dealer). My iPad Air was about 52% when I plugged the new 10 Watt adapter. He began to charge substantially, but the adapter had really hot (I couldn't hold in my hands for more than 3 seconds). It has suddenly stopped working. The 10W adapter feels melted plastic. I let it cool for a while and plugged back in but it looks like it has definitely stopped working. How comes this way is a real Apple adapter?

  Do not know why it does this, but take it back. And certainly do not plug it in again.

• Button ThinkPad 8 Windows has stopped working

  All of a sudden the Windows button has stopped working (no haptic feedback). The Tablet works otherwise, I can always power on it by the power button / stop. Unfortunately, the button power seems to be fragile and probably collapses when it is used on a daily basis.

  Someone has an idea if possible otherwise remedy that is rented for a month in the repair? A loose connector, or something like that? I don't think that it may be a software issue.

  Thank you.

  First Windows button has stopped working, but now, after several weeks, the touchscreen so. I got replacement touch screen cable AP HM 00, 124 of the Lenovo service replacing the cable has solved.

  I guess that's a design flaw , because the cable is longer than it supposed to be (see photo) so it becomes distorted and there caused by a variable pressure on the bottom when cover stand by the fingers on the lower part of 3 mm approximately. Fixation by band does not help, because it always "bubbles" somewhere I hope that this will happen again sooner or later these other two cables (audio connector and display) is not the issue.

  

• The mouse starts to move around and stops working

  I have a desktop HP with Windows Vista Home Basic. Since last or if the mouse started to give problems.

  Suddenly the mouse starts to move everything on the screen and is unresponsive. It opens some programs and suddenly stops. Sometimes the mouse just stops working, but keyboard shortcuts work. I have formatted the computer to its original factory State, changed the antivirus and even checked the mouse but the problem persists. What should I do?

  It looks like a hardware failure, but could be the communication or mouse port.

  You can test it with another mouse? Ideally, one with a different connection type, i.e. If your current mouse is USB, test with PS/2 or vice versa. Otherwise, test with a mouse of the same type. If it is USB, try a different USB jack.

  If it is wireless, check the batteries and make sure the transceiver is as 'visible' as possible to the mouse.

• Pavilion dv7-3020sa, buttons on the top have stopped working.

  Pavilion dv7-3020sa, Windows 7 family (64)

  The buttons that control the mute, volume, DVD and WiFi stopped working. This is probably due to a pilot to be deleted, as I recently suffered a minor but annoying virus.

  I can't find any reference to drivers of these useful function keys. Someone has any idea how to work again.

  Thank you

  It is ok... You can try a step if it may seem very simple, but repeatedly worked to solve this problem... "' Hard Reset '... Proceed exactly as it says and check if it works...

  Hard Reset allows you to solve problems of software and hardware

• My Bluetooth Mobile Keyboard 5000 stagnates and stops working intermittently

  I have a Microsoft Bluetooth Mobile Keyboard 5000 running 64-bit Windows 7 Pro SP1. When it works, it's great, and I like the compact design and wireless. But in the last few months, I noticed a few problems which become quite annoying:

  1. When I'm editing, the keyboard seems often slow to react. For example, I often use combinations of keys such as Ctrl + C or Ctrl + X, and it's as if the keyboard does not have the CTRL key immediately, so I find myself by typing 'C' or 'X' on my choice. If I click Cancel and try again, it usually works after that. Or I'll click on an input field and start typing and it takes 1 to 3 seconds for the text to appear, but it usually everything happens, is not as if the keyboard is in decline in strikes, but just a delay. It's almost like the keyboard has a period of awakening to send data. It doesn't seem to be a way to control or override this behavior. And we don't mean to be away from the keyboard for hours or anything like that; Instead, it's time to switch between windows.
  2. At least once a day, just a keyboard unresponsive altogether. When this happens, I can go into my Bluetooth settings, remove the device, press the Connect button on the back of the keyboard to set pairing mode again (or usually it comes automatically drops back in pairing mode when I delete) and then plug it in again. He sails right through matching and starts working again... until the next time it stops. There seems not to be a lot of consistency to when this happens, but this is often when my boss stops by my office and asked me to show him something. Needless to say, not the best time for the elegant Bluetooth keyboard go toots upward.

  The keyboard said it was MFG. 12/11, is less than 1 year old. Do I need better drivers? Can anyone recommend a troubleshooting step I've overlooked? The keyboard is damaged? I can send it to Microsoft for repair or diagnosis? Do I use? Thanks for any advice you can offer.

  Hello

  -You are aware of any changes made on the computer before this problem?
  -You are faced with the question while working on a certain application (like Microsoft Word) or the licensing is pure coincidence?
   
  Method 1: Run the Troubleshooting Utility from the link below and check if the problem persists.
  Open the hardware and devices Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter
   
  Method 2: I suggest you to see link below and check if it helps.
  Troubleshooting Wireless and Bluetooth problems
  http://www.Microsoft.com/hardware/en-us/help/support/troubleshooting/keyboard/wireless-Bluetooth
  Also, I suggest you to contact Microsoft Hardware Support for better support.
  http://www.Microsoft.com/hardware/en-us/support
   
  Hope this information helps.

• my window vista home edition (rundll32) host process has stopped working.how to overcome this problem

  Windows vista has been giving messages: window has recovered from unexpected shutdown down and showing process (rundddl32) also host windows stopped working. Internet Explore has been blocked or does not. Please tell us the solution-thanks

  Hello

  Thank you for your response.

  I suggest you follow the steps from the link; It will help you solve the problem.

  Method 1: An update is available to resolve a Service outage of Intelligent Transfer (BITS) background on a Windows Vista-based computer: http://support.microsoft.com/kb/940520

  Method 2: Try scanner SFC [SFC system] on the computer that would be a system file corrupt on the computer search and replace.

  http://support.Microsoft.com/kb/929833

  Method 3: If this is a recent problem, then you can try a system restore and check if it helps.

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  To run the system restore, you can see the following link.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  Please perform these steps provided recommended and post back if you still have the problem.

  Hope this information is useful.

• Mouse Bluetooth z8000 difficult to pair and stops working on Lenovo Yoga 3 Windows 10

  Just bought Lenovo Yoga 3 (which came with 10 Windows) and a mouse Bluetooth Z8000.  The mouse is difficult to pair (said matching did not work), but it can pair if the mouse is removed and readded, but then it stops working shortly after.  Yoga 3 supports Bluetooth 4.0.  Tried to install the driver Windows 8 HP and Lenovo Bluetooth driver update, but no change.

  Bruce

  I solved this problem:

  In Device Manager, expand Bluetooth, and then double-click Broadcom Bluetooth USB 4.0.
  In the Intel Wireless Bluetooth Properties dialog box, on the power management tab.
  Uncheck the box "allow the computer to turn off this device to save power".

• Blue Screen of Death and stop working after plugging my Razer Kraken Chroma 7.1 (windows 7)

  (Which mean that I speak French, sorry for my English)

  Hi, I have a problem. When I plug my headphones Razer Kraken 7.1 Chroma, awhile, they just stop working. I heard a noise and that they stop working. I must unplug and plug my headphones so I want them to work again. And this thing is happening very randomly! As for 5 minutes, I have déplug and reconnect but some times, it's job for 20 minutes without problem.

  Also, I feel that if I plug my headphones too fast after this problem, the blue screen of death appear.

  I uninstall and reinstall a lot of time, but don't change anything.

  I have 2 computer: this problems happens on my computer which has windows 7, but when I'm on my pc which has windows 10 all work.

  So thanks to you. Sorry for my English ^^

  Logitech Inc QuickCam LVcKap64.sys associates.  Yours is from 2007.  I would completely remove the software and install a new copy of the most recent driver available.