my hotmail says service unavailable when I try to log

Similar Questions

• always says service unavailable when you try to use the apps

  Hello

  I have a HP Photosmart 5510 and whenever I try to use the said apps try not available service later. I can't connect at all more to him.

  Alright. Press the wireless button and press 'Print report' or 'Print Info', it should print a network configuration for you page.

  After that you have, we will need to access the built-in Web server (EWS) printers. You can do this by entering the IP address of printers (from the Network Setup page) browser press and the address bar type.

  Once there, press the 'Network' tab at the top of the page. From there, you'll want to click on the button "IPv4", on the f-side of the page. It will be there for wireless and wired, so make sure you click the one for you, but you are connected. If you do not see "IPv4", you should see 'Networking', press and press "Network Address (IP).

  Then, you click the small round button next to "Manual"IP address", and then fill in the IP address, subnet mask and default gateway using the information available on the network configuration page.

  For the primary or the preferred DNS server, you will want to enter 8.8.8.8.

  For secondary school or another DNS server, you will want to write 8.8.4.4.

  Click on apply and when the message appears saying that the changes have been applied, press 'OK '.

  Press the power button on your printer, wait that it completely power off and press it again to power it on.

  Let me know if that solves your problem.

• Error HTTP/1.1 Service unavailable when I try to access my sites of Muse...

  I'm going to suddenly have a problem where both of my sites, benvulliamy.co.uk and thetaninn.co.uk, show the Http/1.1 Service unavailable error when I try to access it. It is the same for when I try to connect to Business Catalyst! Any help would be greatly appreciated.

  I found just the other thread on this Http/1.1 Service unavailable

• When I try to log in to my admin user, a screen appears and says ' the user profile service has no logon. User profile cannot be loaded. »

  original title:

  When I try to log in to my admin user, a screen appears and says ' the user profile service has no logon. User profile cannot be loaded. "I can't spend anything for users of our families because they ask for approval from the admin and it won't work. What can I do to correct the admin user?

  You have another admin account , you can connect?
  If so, please do it and then run the Microsoft Support tutorial below.

  If you don't have another admin account, go into safe mode.
  Here's how to get safe mode:
  Shut down your computer > turn it back on and immediately and repeatedly tab key F8 until you see a black and white screen. The top/down arrow and selectSafe Mode with network.

  In the window of logon in safe mode...
  1 can connect to your account administrator in safe mode?
  If so, run the Microsoft tutorial support listed below.

  2. If you can't log into your own account, you see another admin next to your account in the logon screen?
  If you do, that one is the built-in Administrator account. By default, there is no password. Opening of session and run the tutorial from Microsoft technical support below.

  3. If you are able to log on in safe mode, do a system restore. Choose a date when you were able to log in NORMAL MODE as your restore point.
  How to do system restore: System Restore tutorialtutorial from Microsoft support :
  http://support.Microsoft.com/kb/947215
  There are several methods,go through one by one.
  Method 3 has a "fix it for me" application
  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Messenger on Mac just disconnects and says service unavailable or something, but it works well for a few weeks.

  Messenger on MAC disconnects and says service unavailable or something, but it just works well for a few weeks... really annoying, please help!

  original title: WHY IS MSN MESSENGER 8 MAC NOT WORK?

  Hello

   
  You can display the query in the links provided to get better assistance.
  http://mac2.Microsoft.com/help/Office/14/en-us/Messenger/
  http://mac2.Microsoft.com/help/Office/14/en-us/Messenger/category/9cd3c59c-3a5e-441b-ac69-3318ea0398a7

• When I try to log on I see a pop-up that says: this copy of Windows must be activated with Microsoft you can connect. -Enable yes/no?

  When I try to log on I see a pop-up that says: this copy of Windows must be activated with Microsoft you can connect.   -Enable yes/no? When I click on Yes my screen go black and that's it. Nothing happens. I have windows xp professional. For PC refurbished

  Hi Blue85angel,

  ·         What is the number and the model of the computer?

  ·         You did changes to the computer before the show?

  See the following articles in the Microsoft Knowledge Base and check if that helps.

  You are prompted to activate Windows XP or Windows Server 2003 every time that you start the computer

  http://support.Microsoft.com/kb/312295

   

  Blank page to activate Windows in the wizard of Windows Product Activation

  http://support.Microsoft.com/kb/314935

   

  To do: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

   

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756/

   

  You can also contact Activation of Microsoft technical support for assistance:

   

  Activation and registration of a Microsoft product

  http://support.Microsoft.com/kb/326851

  I hope this helps.

• my Media Player from microsoft says this (symaddln) when I try to run it and stops. What do I need?

  Remember - this is a public forum so never post private information such as numbers of mail or telephone! my media player microsoft says this (symaddln) when I try to run it and stops.

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem
  Hello
   
  What security software is installed?
   
  This "symaddln" occurs especially if you had Norton installed anti-virus software.
   
  I suggest you follow the steps below and check if the problem persists.
   
  Step 1:
   
  (A) I would say you temporarily disable your security software (if you are using Norton) and check if the problem persists.
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
   
  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
   
  (B) If you already have Norton Security software before and uninstalled later, there would be traces of which would result in the computer does not normally. I suggest that you use their uninstall/removal tool to uninstall Norton Security software traces.
   
  http://www.Symantec.com/Norton/support/kb/web_view.jsp?wv_type=public_web&docURL=20080710133834EN
   
  Step 2:
   
  If this does not help, I would say you put your computer in a clean boot State and check if the problem persists. This could be the result of a conflict of software of third party causing the problem to occur.
   
  Note: Be sure to follow step 7 to start your computer in normal mode.
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• I bought and installed Lightroom 6.  It works but there is a message saying that my trial period has expired and when I try to log in to Lightroom on my iPad it says the same thing.  How can I fix it?

  I bought and installed Lightroom 6.  It works but there is a message saying that my trial period has expired and when I try to log in to Lightroom on my iPad it says the same thing.  How can I fix it?  I got a trial of Lightroom CC before I installed.

  allen456 wrote:

  Is there anyway that I can go to CC without losing all my investments in Lightroom 6?

  No, it is not AFAIK. You can try back LR 6 and then buy the subscription of photographers. You will need to contact Adobe about this.

  Note that this is not Adobe. This is a user to user forum.

  Do a search for Adobe product return.

• I have 5 Lightroom on a new Mac - I have the original label and the number of services.  When I try to enter, I get a message that the serial number is invalid.  What can I do

  I have 5 Lightroom on a new Mac - I have the original label and the number of services.  When I try to enter, I get a message that the serial number is invalid.  What can I do

  Thanks - Yes, it's the LR5.

  2 hours on the phone with Adobe technical support, it is fixed.

  I guess it was a mistake with the original installation.

• There seems to be a problem with the soft ware.  We use the CS6 for Records services and when we try to save the record, part of the record is stored. The record to be saved as an mp3 file is 70 to 100 KB but recently only 3 KB are generally

  There seems to be a problem with the software.  We use the CS6 for Records services and when we try to save the record, part of the record is stored.  Usually the recording to be saved as an mp3 file is 70 to 100 KB but recently only 3 KB are recorded.  What should I do to fix this?

  You may need to reset your preferences of hearing files stored in C:\Users\"username"\AppData\Roaming\Adobe\Audition\5.0. If you rename this folder in 5.0.bak that hearing won't find it when you open the next time if it will recreate a new settings with the default settings folder. See if hearing then works as expected.

• When I try to log on; the message indicates that the profile of the user didn't log in

  Original title: user profile

  Hi there, anyone know how to recover a Windows Vista administrators password.  Currently I am locked with when I try to log in. the message indicates that the user profile is not the newspaper.

  Using standard Microsoft shows a procedure to copy and paste the profile to fix it, but this assumes that the broken account is a standard user account and not the administration.  When the system asks the admisistrator password access details - of course it does not work because of the problem of user profile.  Any help would be great.
  B

  Hello I suggest you to follow the steps in troubleshooting this article and check if it helps Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile. http://support.Microsoft.com/kb/947215

• I get "proxies cannot be captured by a stateless session" when I try to log in to this site. I went there there more than once in the past, but this is the first time I received this answer and you are unable to log on to this site.

  I've logged on this particular site, http://www.springairsystems.com/SpecAndQuote/User/Login/View.aspx a number of time's recent past. When I try to log in now, I get a prompt in red letter indicating, "proxies cannot be captured by a stateless session." What should I do to open a session? I set my privacy settings to allow cookies from Firefox, but is not alleviate the problem.

  See this - http://en.wikipedia.org/wiki/Proxy_server

• I have updated and now when I try to log on to Web sites with fingerprint reader, I get "Firefox doesn't know how to open this address, because the Protocol (dpql) is not associated with any program."

  I have updated and now when I try to log on to Web sites with fingerprint reader, I get "Firefox doesn't know how to open this address, because the Protocol (dpql) is not associated with any program."

  What is the Digital Persona fingerprint scanner? If it's that they have abandoned, for more details, see https://support.mozilla.com/en-US/questions/799388

• When I try to log the p2p soulseek site, I get the error message "connection failed: socket error.» change the connection settings. How can I fix it?

  "socket error".

  When I try to log the p2p soulseek site, I get the error message "connection failed: socket error.» change the connection settings. How can I fix it? Is - this type of error called a winsock error?  It keeps happening to me on this site. What I've read, it happens when you make changes to a program before concluding that under its weight. Could it happen because I'm deleting files, I don't think that will be completed while the other files are D/Ling? That's what I'm doing wrong? I found a solution to correct an error in Winsock that is to enter the "command prompt" and type "netsh winsock. Will this work? (I'm sorry I have so many questions in this post, but I have had TO KNOW!!)

  Hello

  I suggest you send the question here for best support about the issue.

• I am Age of Empires to steam, and when I try to log in, it tells me that I need a product key that I have ever received.

  Hi, I had the age of empires of the steam, and when I try to log in, I have a product key... can you guys please help me?

  original title: age of Empiers

  Hello Hiddenxin,

  I would recommend posting your question on the forums of Steam for Age of Empires:
  http://forums.steampowered.com/forums/forumdisplay.php?f=1302