My laptop fell and does not start

Similar Questions

• Laptop fell and does not start correctly

  My phone fell on the floor (about 1 1/2 feet off the ground) and when I went to use again it was a black screen. I restarted. Now I have a message that says "no boot device - insert boot disk and press any key any." I turned market a few times and get the same message. I don't know how to go beyond that and do not know where are my backup disks. The laptop is a Pavilion dv5-2129wm with Windows 7. Can someone help me?

  Hello

  There are few moving parts on a computer whose HARD drive. Some more expensive laptops have some kind of protection for the HARD disk, but much cheaper are not therefore a fall/fall can cause many thing for HARD drive especially IF during the market. Please follow the instructions below to verify and correct the first:
  
     http://support.HP.com/us-en/document/c01443463
  
  Good luck.

• 6735 b hangs and does not start on battery

  My 6735 b does not start on battery. Just hangs until I plug in the power supply. For some odd reason, I can't access the drivers even though I have the laptop regestered? Can someone post a link to the update of the bios for me?

  Glenn,

  The server is maybe out of service.  I reported the problem with the web page.  Yours is not the only page not available at the moment - something's up.

  Hang in there and try again later.

  Just for the record, in the case where it is useful:

  Test and calibrate the battery (Windows 8)

  Test and calibrate the battery (Windows 7)

• NB just by making the effort test and does not start backup

  HP dv7-4177 started having types, wouldn't restart. I tried to test that are inbeded and when I did the stress test he stops and does not restart. I hit the power button and nothing happens. I took the hours of battery sevealr and handed over in but I have nothing seems to help.

  Hello Nutn Spec.  I understand that your notebook is currently unable to boot.

  What kind of questions you know before performing the stress test?  This will help me identify the cause of the problem.

  Have you tried to do a hard reset?  It drains all the residual energy of the laptop and hardware reset forces.  If you haven't tried this before I would suggest trying the following.

  1. Make sure that the laptop is completely turned off.
  2. Remove the battery and AC power.
  3. Press and hold the power button for 15-20 seconds, three times.
  4. Replace the battery and AC power.
  5. Try to start Notepad.

  Let me know the result.  I will keep an eye out for your answer.  Have a great night!

• Computer laptop Windows XP does not start.

  My laptop does not start. When I first put it on the screen says 'we apologize... ". Windows does not start automatically in... "Then the Windows XP screen as it tries to load there is this small blue screen that appears a second microphone, too fast to read, then goes back to 'we apologize...". "screen just keeps looping. I thought that my hard drive was going badly, so I ordered a new. I have XP SP3. Could someone help me please?

  Hi robestes3,

  1. When did you start to question?

  2. you remember to make changes to the computer before this problem?

  Method 1:

  First of all, you can tryLast good known Configuration and check if helps solve the problem.

  Check out the link:

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  Method 2:

  Step 1:

  If the above method does not work, then you can try to start in safe mode and check if the problem occurs.

  Check out the link for more information on starting your computer in SafeMode below:

  http://support.Microsoft.com/kb/315222

  Step 2:

  If you can boot into safe mode without any problem, and then try to perform a clean boot. A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  http://support.Microsoft.com/kb/310353

  If your problem is resolved after the clean boot, and then follow the steps mentioned in the article above to refine the exact source:

  In addition, after you resolve the problem, see the section on how to restore your computer to a Normal startup mode.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Open my laptop, now it does not start

  Hi everyone, the first time poster.

  I opened my laptop (touchsmart tm2 1070ca) to attempt to clean the keyboard and now it does not start at the top.  all the LEDs light up, but the caps lock LED flashes.  The fans and hard drive look about 2 seconds before silence, and about 10 seconds later, the laptop beeps loud and then stops.

  When I opened upward, the touchpad is detached from the motherboard. I finally get it reconnected, but it turned out to be very difficult.

  I tried the Bios recovery suggested on the support site, but it had no effect.

  any help would be massively appreciated.  no no not my laptop will really make my life difficult.

  I know this is an old thread but since there was no solution, I felt should display what has worked for me, in case someone else has this problem.

  This morning my computer refuses to start and the caps lock blinked. I've read elsewhere that a user of a model different from simply removed HP sound CD ROM and re-inserted. My laptop is a HP tm2 Tablet PC, so it doesn't have a removable CD ROM, but I was wondering if another device had become "loose". First, I removed the dongle USB for my mouse and battery and then restarted. That did not help so I forced a stop down (press the power switch.) Then, I opened the background panels and reinstall the RAM (actually happened two sticks to make sure) and removed and re-inserted the HD then restarted again. I don't know which of these factors did the trick, but it worked.

  Hope someone finds this useful info.

  G.

• iPhone hot 5s fees and does not start

  phone is connected to the load.  After a while I checked it and it was very hot.  I unplugged it and now it does not start.

  Have you ever tried to force reboot the phone by holding down the button sleep and home for 10 seconds, until the Apple logo comes back again? You won't lose data.

  More troubleshooting can be found in this article:

  If your iPhone, iPad, doesn't respond or won't turn on - Apple Support

• J2S63EA #BH5: Watch restoration incomplete error and does not start

  Some of my keys were not working nd varies touchscreen
  I decide to use Recovery Manager to reset the default system
  I waited for the sytem finish restoration
  It boot after auto restart
  It shows no logo
  then watch date th hour almost immediately the
  Go Manager recovery Windows telling me restoration is not complete
  that I should choose between saving the details of the log and try again
  Click try again without success
  It starts not far from this point
  pls help
  This is my new laptop go and is not yet nearly a year, my father, it has for me

  Try the trick here:

  http://h30434.www3.HP.com/T5/notebook-recovery/HP-envy-TouchSmart-17-recovery-incomplete/m-p/4760233#M65038

• Get beeps when the computer starts and does not start

  Original title: Hello I have Mo Intel DG31PR & 2 GB Transcend RAM while the switch on it give beep 4 times and you would be in this case for several attempts does not start and it begins so please help and what is the problem?

  Nothing more to say

  Pravin Dave

  Hello PravinDave,

  If we get the beep codes and the machine will not move past, then we have hardware problems.

  You will need to contact your hardware manufacturer for more information on the beep codes and their meaning.

  Best regards

  Matthew_Ha

• When I started my computer this morning, it ran chkdsk at startup, windows startup it goes immediately to chkdsk, it will be repeated again and again. I can boot into safe mode, but if I try to start windows normally it runs chkdsk and does not start

  Windows does not start normally, just run chkdsk again and again

  First test the hard drive to make sure it's healthy. Test the hard drive with a diagnostic utility downloaded from site of the disc mftr. or use SeaTools for BACK of Seagate. You create a bootable CD with the files you download. You will need a third party burning software to do as the free ImgBurn, Nero or Roxio. Burn as an image, not in the form of data.

  http://www.ImgBurn.com

  http://www.Seagate.com/www/en-us/support/downloads/SeaTools/seatooldreg
  http://Seagate.custkb.com/Seagate/CRM/selfservice/search.jsp?docid=201271 (how-to)

  Boot with the CD that you have done and do a full test of the reader. The physical tests fail, replace it.

  If the hard drive then passes the physical tests, safe mode:
  Start > run > cmd [Enter]
  fsutil dirty query c: (or the appropriate drive letter) [Enter]

  This will tell you if the disc is dirty or not. Then always in cmd:

  chkntfs /x c: (or the appropriate drive letter) [Enter]

  This tells Windows not not to check this drive at startup. Reboot and it should go on the desktop. Once Windows loaded, run cmd and:

  Chkdsk /f /r c: (or the appropriate drive letter) [Enter]

  CHKDSK will run through all 5 steps. After that it's over, always in cmd:

  fsutil dirty query c: (or the appropriate drive letter) [Enter]

  to see that the dirty bit is not set on this drive.
  MS - MVP - Elephant Boy computers - don't panic!

• Laptop computer G60 does not start

  I'm having some trouble starting by G60 Notebook.  The system runs Windows 7, but since it does not start I don't know if the system is a 32-bit or a 64-bit.  What seems to be the case, it's that he's trying to start and simply itself turns off.  For this, this little trick after having tried to boot Windows "normally".   I ran the diagnostic tests for memory and disk and both indicate that memory and disk are in agreement.

  I now get a cannot find the BOOTMGR.  I tried to recover the BOOTMGR using the recovery partiion, but what I will meet with the first issue of the computer itself put it off before it can perform the restore.  I do not have the disks for the OS, so if it's the secret I have to order a set.

  Your help is appreciated.

  Hi @LarryN

  Thank you for your request, I will do my best to help you.

  I understand when you try to start Windows normally, it turns off automatically.  You were able to test the hard drive and memory and all the two passed.

  Here is a link to an overheating and Auto Shutdown Troubleshooting questions that can help.

  Here's another if this isn't the issue. Troubleshooting of Error Messages on a Blue Screen may occur at the start or start

  You can also try booting in safe mode. Enter SafeMode (Windows 7)

  Select repair your computer.

  If the problem still persists repeat the process above, but select Safe mode with command prompt and follow the instructions to open the system recovery options.

  Again choose command line

  Enter the following information to the /rebuildbcd bootrec command prompt and press ENTER.

  Once this completed successfully try to start Windows normally.

  If you still have a question I suggest make a recovery in the factory

  Performing a recovery of system HP (Windows 7)

  While the recovery, there is an option to backup your personal files to avoid data loss.  If you do not already have one, now is a great time.

  Restore files that have been supported to the top using HP Recovery Manager (Windows 7)

  At any time you can contact HP support for assistance.

  Please contact our technical support at 800-474-6836. If you do not live in the United States / Canada region, please click on the link below to get a number of assistance for your region.

  World wide phone holder

  Good luck!

• Laptop HP Pavilion 2320DX g4: computer hp laptop pavilion g4 does not start successfully after update and return to windows 8.1

  Hi, I have recently updated my laptop to Windows 10. He had so many problems and I didn't like it at all, so I just returned my laptop to Windows 8.1.  Since then, my laptop does not correctly every time, and the fan immediately starts to work as well. I can start my pc and connect to my home screen each time.  If the tile is moving or light up when I move my cursor, then I know that I can use my laptop for a little while. It can freeze after getting out a good program. Other times when I start my laptop, everything is dead except for logging on my screen. My Windows key on the keyboard does not work most of the time.  If the screen does not respond the first time I turn, as described above, I can't absolutely nothing on my pc. I can't access the search bar by moving the cursor to top right, I can't open the tiles, I can't spend in desktop mode, etc.  Front I upgraded to Windows 10 and downgraded to 8.1 all worked perfectly, because I've updated from 8.0 to 8.1 Windows almost 2 years.  I have a defective battery. in fact I can only use my laptop if it is plugged. My fan is constantly going, but I don't know if it's my loss of battery or what's wrong with my pc now.  I have described my problem in the Microsoft community forum but have had little response that was not helpful. I was told to go to the command prompt and put in DISM: scan now (which also contained letters more than that, but I do not remember all). I followed the instructions and for 2 days, my pc seems to do better. Then he returned to this problem again. I hope you can help me.  If you have additional questions, post here or please email me at [removed personal information]. Thank you!

  DEB

  @DWESTDEWITT,

  Hello and thanks for the display on the HP support forum.  What you can do at this point that there are several updates released by microsoft and hardware vendors is running the Windows Update Troubleshooter.

  If this fails to solve the problem.  The only option will be to restore the operating system to the previous, until HP gets the drivers so that they can release them on the support page for your laptop for Windows 10.

  Thanks again for posting and have a great day.

• MacBook Pro glued on the gray screen and does not start. Help, please!

  Hello

  My 13 "MacBook Pro (mid-2009), running Snow leopard (10.6.8), has finally given up and won't start.

  I tried to boot into SafeMode several times, but the loading bar does not move and the laptop just completely stops.

  I also tried to boot in single user mode with the command fsck - fy, but this results in the following:

  disk 0 s 2: I / 0 error

  Invalid node structure

  (4,35296)

  * The Macintosh HD volume could not be completely checked.

  / dev/rdiskOs2 (hfs)

  You leave with signal 8

  I guess that means that there is something wrong with the hard disk and some corrupt files?

  My problem is that I have no time machine backups, so I would like to know if it is possible to do something to get to the top and running.

  That, I do not have an external drive with my main important files and photos on a failure, so is it possible to completely erase the computer so I can sell it at least?

  I really need help on what I've been driving myself crazy trying to figure it out!

  I'm not all techniques with regard to the material. I tried doing research and have seen things, which suggests that I should reinstall the OS X, this would imply in the disks provided with the laptop when the power?

  Any advice greatly appreciated!

  Boot from the DVD and run the check/repair disk utility and repair permissions until you get no errors.  Reformat the hard disk using Disk Utility/Erase Mac OS extended (journaled), then click on the Option button and select GUID. Then re-install the operating system.

  When you restart, use Setup Wizard to restore your data.

• Yoga 2 repetitive pro reboot and does not start

  Turned on my laptop this morning. Worked well. Went to try to use my printer to scan something to my laptop. Printer turned on and came back to my laptop does not. It is just to turn on and off again. The Start button / stop and the keyboard backlight flash just turn off repeatedly.

  Tried searching forums for a solution. Here's what I've tried so far:

  Laptop not connected to the power source

  Battery disconnected

  Disconnected battery CMOS (CR2016)

  Laptop plugged in and still get the same problem of restart

  Ive tried holding down the power button / stop and small button above does not. I also tried holding on to the power supply with battery disconnected and battery connected CMOS. Always the same question: repetitive restart with no boot. Printer has been turned off during the whole process of troubleshooting but worked well with wifes laptop after that mine pooped the bed.

  Anyone got a solution or an idea?

  FYI - took it to a Tech Said motherboard needed replaced. $800 or more.

  Comment to Moderator: Post edited to conform to Community rules.

• My iMac is flashing at me and does not start!

  I turn on the iMac and it starts to load but gets half way then flashes to black screen and stops to load and crashes with a router? as if taken between the opening and closing? Picture attached

  Probably a failed HD Try booting into the recovery (command-R) to the boot partition. Open utility disk - First aid, then run First aid on the hard drive. If this does not work, then take the local computer to your Apple Store or the authorized Apple service provider to be repaired.