Similar Questions

• Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

  I got a modem Comcast/Xfinity upgrade. Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?

  Whenever you change the modem or modem/router on a network, AirPort Extreme will be reset to the default settings and then set it up again to work properly with the new modem. For this he would be...

  Turn on AirPort Extreme for a few minutes... If it is not already turned on

  Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds, then release it.

  Allow a minute for the AirPort Extreme restart to a slow, flashing amber light status

  Make sure that an Ethernet cable connects to one of the four LAN <-->Ethernet ports on the modem/router on port WAN "O" on AirPort Extreme

  To start the Setup program, click the WiFi icon at the top of the screen on your Mac and are looking for a list of the new AirPort base station

  Just below that, click directly on the AirPort Extreme and then follow the prompts for configuration "Wizard".

  When you configure AirPort Extreme once again, you can use the same wireless network name and the same password that you used with AirPort Extreme with the 'old' modem, if you wish, or use a new wireless network name and password

• E2500 router communicates only with HP printer cable.

  I have a HP color LaserJet 2605dn printer and router e2500. I decided to run an Ethernet cable from the router to the printer instead of via the USB port of the laptop that works fine for a couple of years.

  Is the green light on the router would be flashing quick or light yellow on the printer. Guess there is a communication problem. After some reading material at random on Web sites and messages, I manually changed the IP address of the printer: 192.168.1.110 (that is outside the range of the DHCP users (6) quantity, which starts at 192.168.1.100)

  Leave the configuration window Panel > devices Printers & I added a new "Standard TCP/IP Port" to match the one I put manually (192.168.1.110).

  I varied results when I ping this new IP address while that the yellow light on the Ethernet port on the printer flashes quickly. Sometimes I will have 4 packets that have been sent in the ping also received, sometimes none are received, sometimes 1 and sometimes 2 packets are received. For example, ping results are contradictory and I don't know why that should be.

  I guess that none of my configurations 'Basic Wireless Settings' and "Wireless Security" have an impact here. After all, I'm trying only to communicate with my printer wirelessly via my laptop to the printer via a network cable. Also, I'm not a very technical person. I managed to get this far, but I'm at a loss for what keeps my router to communicate with the printer of mine. Any help would be appreciated. Thank you.

  Using the printer management page, make sure you on the JetDirect Automatic for networking information. If your automatic support of networking, it must acquire an IP address from the router if the LAN cable is in good working condition. Make a print on the printer configuration page to see what IP address it acquired from the router.

  If you decide you want to put a static IP address on the printer, make sure you on the JetDirect information
  Manual and instead use 192.168.1.110 tends in the poole DHCP address, try using 192.168.1.26. You will need configure the printer driver in windows accordingly to point to the IP address.

• Cisco router restarts randomly with Bus error

  Cisco router restarts randomly with the following error:

  System has been restarted by error of bus to PC 0x4183614C, speech 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013

  I've pasted below see the chimneys and release the version.

  view the stacks

  
  

  Minimum factory chimneys:

  Format name / free

  5396/6000 inspect Init Msg

  Subsystem SPAN 5368/6000

  58920/60000 EEM Auto record Proc

  Automatic start of 4772/6000 upgrade process

  DIB 5164/6000 error message

  HAND OF SASL 5396/6000

  4968/6000 LICENSE DEFAULT AGENT

  5368/12000 Init

  4216/6000 update prst

  4384/6000 VPN_HW_MIB_CREATION

  5188/6000 RADIUS INITCONFIG

  Update process random rom 2128/3000

  8356/12000 SSH process

  Stats URPF 5316/6000

  Interruption of battery level:

  Level named format / unused

  Network interfaces 1 1484828 6284/9000

  2 3264990 8548/9000 DMA/Timer Interrupt

  3 1 8388/9000 PA Int management Manager

  Console 4 115 8612/9000 Uart

  External interrupt 5 0 9000/9000

  NMI 7 223352 8564/9000 interrupt handler

  Spurious interrupts: 11

  System has been restarted by error of bus to PC 0x4183614C, speech 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013

  Software of 2800 (C2800NM-ADVSECURITYK9-M), Version 12.4 (24) T, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Updated Thursday 25 February 09 17:55 by prod_rel_team

  Image text-base: 0 x 40011240, database: 0x42B41940

  The failure of the system stack trace:

  FP: 0X472252B8, RA: 0X4183614C

  FP: 0 X 47225310, RA: 0X418312F8

  FP: 0 X 47225348, RA: 0X41647DC0

  FP: 0X472253A8, RA: 0X4164A8F4

  FP: 0 X 47225428, RA: 0X4164B248

  See the version

  
  

  Cisco IOS software, 2800 Software (C2800NM-ADVSECURITYK9-M), Version 12.4 (24) T, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2009 by Cisco Systems, Inc.

  Updated Thursday 25 February 09 17:55 by prod_rel_team

  ROM: System Bootstrap, Version 12.4 (1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

  availability of Cisco is 28 minutes

  System returned to ROM by bus to the 0x4183614C PC error, address 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013

  System image file is "flash: c2800nm-advsecurityk9 - mz.124 - 24.T.bin".

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 2821 (revision 53.51) with 1036288K / 12288K bytes of memory.

  Card processor ID FCZ1017732F

  2 gigabit Ethernet interfaces

  2 modules of virtual private network (VPN)

  Configuration of DRAM is wide with parity 64-bit capable.

  239K bytes of non-volatile configuration memory.

  250880K bytes of ATA CompactFlash (read/write)

  Configuration register is 0 x 2102

  You want to use the tool interpreter of output for this work:

  http://www.Cisco.com/pcgi-bin/support/OutputInterpreter/home.p

  For more information about the resolution of crashes, see this article:

  http://www.Cisco.com/en/us/products/HW/IAD/ps397/products_tech_note09186a00800b4447.shtml

  In this case, it looks like CSCsy09250, described here:

  http://www.Cisco.com/en/us/products/CSA/Cisco-SA-20100324-SCCP.html

  You should contact Cisco for the software updated by following the instructions of this bulletin.

  That crash possibly caused by part of sone intentionally sends out packets malformed to your device, so if you have reason to believe that someone in your community could run metasploit or similar "Penetration Testing" tools, you can look into that as well.

• router in 1921 with the double nat ADSL problem

  I have problems with the implementation of a router in 1921 with double lines ADSL for failover. For some reason any internet traffic keeps using Dialer 1 as internet main connection, while 2 Dialer should be primary. Also, when I finish my NAT with allowed a full acl, it translates the public ip address of the 2-to-1 Dialer the Dialer before she sends in the internet.

  This is my config:

  !
  interface GigabitEthernet0/0
  Voice netwerk description
  IP 192.168.77.254 255.255.255.0
  IP helper 192.168.177.1
  IP helper 192.168.177.254
  IP nat inside
  IP virtual-reassembly in
  IP tcp adjust-mss 1400
  automatic duplex
  automatic speed
  !
  interface GigabitEthernet0/1
  Inside the interface description
  IP 192.168.177.254 255.255.255.0
  IP mtu 1492
  IP nat inside
  IP virtual-reassembly in
  IP tcp adjust-mss 1400
  automatic duplex
  automatic speed
  !
  ATM0/0/0 interface
  Description 1/10 Mb Tele2 ADSL
  no ip address
  No atm ilmi-keepalive
  PVC 0/35
  aal5mux encapsulation ppp Dialer
  Dialer pool-member 1
  !
  !
  interface Ethernet0/0/0
  no ip address
  Shutdown
  !
  ATM0/1/0 interface
  no ip address
  No atm ilmi-keepalive
  !
  interface Ethernet0/1/0
  VDSL 5/50 Mb KPN description
  no ip address
  !
  interface Ethernet0/1/0.6
  KPN VDSL description
  encapsulation dot1Q 6
  PPPoE enable global group
  PPPoE-client dial-pool-number 2
  service-policy output parent policy
  !
  interface Dialer1
  Tele2 ADSL description
  the negotiated IP address
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP mtu 1492
  NAT outside IP
  IP virtual-reassembly in
  encapsulation ppp
  IP tcp adjust-mss 1400
  Dialer pool 1
  Authentication callin PPP chap Protocol
  PPP pap sent-username *.
  No cdp enable
  card crypto SAL_map
  !
  interface Dialer2
  VDSL KPN description
  the negotiated IP address
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP mtu 1492
  NAT outside IP
  IP virtual-reassembly in
  encapsulation ppp
  IP tcp adjust-mss 1400
  load-interval 30
  Dialer pool 2
  PPP authentication pap callin
  PPP pap sent-username *.
  No cdp enable
  card crypto SAL_map_VDSL

  !

  IP nat inside source overload map route sheep interface Dialer1
  IP nat inside source overload map route nonat2 interface Dialer2
  IP route 0.0.0.0 0.0.0.0 Dialer2 Track1
  IP route 0.0.0.0 0.0.0.0 Dialer1 254
  !

  auto discovering IP sla
  ALS IP 10
  echo ICMP - 62.69.174.75 source-interface Dialer2
  Timeout 30000
  frequency 30
  Annex IP SLA 10 life never start-time now
  !

  access-list 102 deny ip 192.168.177.0 0.0.0.255 host 192.168.1.249
  access-list 102 deny ip 192.168.178.0 0.0.0.255 host 192.168.1.249
  access-list 102 deny ip 192.168.179.0 0.0.0.255 host 192.168.1.249
  access-list 102 deny ip 192.168.177.0 0.0.0.255 172.28.1.0 0.0.0.255
  access-list 102 deny ip any 192.168.255.0 0.0.0.255
  access-list 102 deny ip any 192.168.254.0 0.0.0.255
  access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.179.0 0.0.0.255
  access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.178.0 0.0.0.255
  access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.79.0 0.0.0.255
  access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.78.0 0.0.0.255
  access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.179.0 0.0.0.255
  access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.178.0 0.0.0.255
  access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.79.0 0.0.0.255
  access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.78.0 0.0.0.255
  access-list 102 permit ip 192.168.177.0 0.0.0.255 any
  access-list 102 permit ip 192.168.77.0 0.0.0.255 any
  !

  Dialer-list 1 ip protocol allow
  Dialer-list 2 ip protocol allow
  !
  nonat2 allowed 10 route map
  corresponds to the IP 102
  Set the interface Dialer2
  !
  sheep allowed 10 route map
  corresponds to the IP 102
  Set the interface Dialer1

  the ACL is built to exclude some ips private for ipsec VPN destinations.

  Any suggestions on what I'm missing? It must use dialer 2 as primary internet connection and failover of Dialer 1 if IP SLA fails. The SLA config seems to work properly:

  SH ip route

  S * 0.0.0.0/0 is directly connected, Dialer2
  84.0.0.0/32 is divided into subnets, subnets 1
  C 84.246.25.231 is directly connected, Dialer1
  145.131.0.0/32 is divided into subnets, subnets 1
  C 145.131.131.112 is directly connected, Dialer2
  192.168.77.0/24 is variably divided into subnets, 2 subnets, 2 masks
  C 192.168.77.0/24 is directly connected, GigabitEthernet0/0
  The 192.168.77.254/32 is directly connected, GigabitEthernet0/0
  192.168.177.0/24 is variably divided into subnets, 2 subnets, 2 masks
  C 192.168.177.0/24 is directly connected, GigabitEthernet0/1
  The 192.168.177.254/32 is directly connected, GigabitEthernet0/1
  192.168.254.0/24 is variably divided into subnets, 2 subnets, 2 masks
  S 192.168.254.0/24 is directly connected, Dialer2
  192.168.254.37/32 S [1/0] via 77.241.229.241
  S 192.168.255.0/24 is directly connected, Dialer1
  212.121.121.0/32 is divided into subnets, subnets 1
  C 212.121.121.183 is directly connected, Dialer2
  213.144.228.0/32 is divided into subnets, subnets 1
  C 213.144.228.72 is directly connected, Dialer1

  http://docwiki.Cisco.com/wiki/category:NAT

  Above document indicates "Beware of the use of the ACL for the NAT with" ip allow a whole ' you can get unpredictable results. " I suggest using the "road-map sheep/nonat2 permit 20" instead of "allow a whole."

  For others, change the config as follows-

  !

  ALS IP 10
  Dialer2 interface source ICMP echo 8.8.8.8
  Timeout 30000
  frequency 30
  Annex IP SLA 10 life never start-time now

  !

  IP route 8.8.8.8 255.255.255.255 permanent dialer2

  !

  !
  nonat2 allowed 10 route map
  corresponds to the IP 102
  match interface Dialer2
  !
  sheep allowed 10 route map
  corresponds to the IP 102
  match interface Dialer1

  !

  IP nat inside source overload map route sheep interface Dialer1
  IP nat inside source overload map route nonat2 interface Dialer2

  !

  NAT-TRACK event manager applet

  track event 1 show all

  order cli action 0.1 'enable '.

  action 0.2 wait 2

  action command 0.3 cli "clear ip nat translations forced."

  action 0.4 syslog msg "Translation NAT cleared after state change of track"

  !

  -Ginette

• Need to know if my router is compatible with windows 7

  The microsoft Web site seems to send me in circles and it drives me crazy! What I want to know is if my wireless method NB9W router is compatible with windows 7 or not...

  It is a work laptop and our COMPUTER technician has not set. I can connect to the network wirelessly at work, but not my own wireless network at home. I read that some 'old' routers are not compatible with windows 7.

  I can't find any info on my model of router on the microsoft Web site. Help please!

  Hello

  Collate support method because it might be and need the firmware, for example.

  Using WPA or WPA2 (and not WEP) security? The value WPA or WPA2.

  NB9W
  http://www.netcomm.com.au/Netcomm-products/VoIP/nb9w?SQ_PAINT_LAYOUT_NAME=support

  This implies that it is Windows 7 compatible (might still need the firmware)

  Windows 7 - obtain an IP address
  http://www.YouTube.com/watch?v=XC7Ebm0UKi8

  and

  Windows 7 - wireless connection
  http://www.YouTube.com/watch?v=MqWJ7exMJhE

  NB9W
  http://www.netcomm.com.au/Netcomm-products/VoIP/nb9w

  Method Support
  http://www.netcomm.com.au/support

  It can be configured to not work on networks other than at work, have your tried on
  other networks in addition to work and home?

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• VMware Update Manager - Setup failed with an unknown error. vCenter credentials could not be validated

  Hi all

  I have my getting the error next message when I try to install VUM.

  VMware Update Manager - Setup failed with an unknown error. vCenter credentials could not be validated

  Help, please.

  Hi John,.

  Please follow the link below.

  http://www.virtualmvp.com/VMware-Update-Manager-Setup-failed-with-an-unknown-error-vCenter-credentials-could-not-be-validated/

  Thank you

  Venance

• recently purchased a samsung NX30 camera which came with lightroom 5, after several hours of searching on Google I got it setup properly with the right camera raw to be able to access my raw images. I found that my old laptop is very slow during the proce

  recently purchased a samsung NX30 camera which came with lightroom 5, after several hours of searching on Google I got it setup properly with the right camera raw to be able to access my raw images. I found that my old laptop is very slow during the processing of hundreds of images that I usually take on a weekly basis.  I bought a new faster laptop, but when I looked for the cd with the software of series and I couldn't find in the mess of Christmas.  I downloaded a trial version of lightroom and got, it works on my new laptop. Is there a way to access the serial number of my version already installed and insert it in the version of track to make it work for me?

  Myron

  If you take the time to register to your original with Adobe installation (which most people do not), you can log in to your Adobe account and get the serial number. If you use a Windows computer and still have access to the old computer where Lightroom is installed, you can do the following:

  1. in the window folder options, make sure that you are able to see hidden folders.

  2. go to the C:\ProgramData\Adobe\Lightroom folder.

  3. use Notepad to open the file, Lightroom 5.0 Registration.lrreg

  You will be able to retrieve your serial number of this file.

• Not active Ethernet E3200 ports if daisy chained with 2Wire modem/router?

  I have a 2Wire 2700G - B DSL modem/4 port router provided by ATT. The WiFi range has a problem so I had a router Linksys E3200 to extend range. I ran the cable Cat5 100 feet across the House and connected the linksys E3200 Cat5 between one of the 4 Ethernet ports on my 2Wire and the Port of 'Internet' from the Linksys 3200. I put in place and seem to have a stronger second network access this router wireless (although it is not a Repeater, I alternate between two wifi networks as I walk home with my iphone).

  I plugged in the Linksys E3200 ports WIRED devices wired Ethernet and they are not recognized by my PC as the devices connected to the 2Wire ethernet ports are. My PC is plugged into the port of 2Wire as well.

  How can I activate the 4 ethernet ports on the 3200 to be additional ports to my home network as the 4 on the 2Wire?

  http://homecommunity.Cisco.com/T5/wireless-routers/connecting-two-routers-wired-the-definitive-answe...

• router Linksys with netgear with comcast

  We have problems with our wireless network that we have more than 5 Mac devices on our network. Comcast proposed to attach a Linksys router at our comcast netgear existing router to add 5 ip addresses more to our mixture. Is there a model that would be better for this configuration? Thank you!

  You don't need another router.  One you have will work fine.  However, you will need to go the Netgear forum for assistance.  Your Cable Guy doesn't know what he's talking about.  If you really have an IP address conflict, you will need to find it.  To help, make sure that all devices are set to DHCP and do not have a static IP address.   I'm assuming that the router is a router 4 ports.

• Problems running Setup.app with e4200v2 and Mac network

  I bought a router e4200v2 about a year, but somehow, it got lost in my computer room and I don't a not localize until quite recently, just after I bought a new iMac running Yosemite. The new iMacs don't have an optical drive, so I downloaded the Setup.app since the support site of Linksys without problem.

  However, when I run the Setup.app, he starts a Setup Smart Wi - fi but stalls when it comes to about 25% of fact, with a message "could not find your router." I called Linksys, and even if this isn't their period of free support they gave me a free call since I'd just take the machine out of the box.

  We couldn't get the Setup.app to work, so they talked me through a manual installation. I can now access the net of my Wired iMac or any of the various devices wireless around the House (telephone, laptop, etc.).

  BUT it was only after I hung up I have realzed that the different functions available from the diddn t Smart Wifi configuration (for example, guest access) appear to be available.

  I don't want to pay for a support call, but it's really irritating. The Setup.app still does not work, and I see no way to not get LLA.

  Can anyone suggest a solution? Am I missing something simple?

  Thank you.

  I do not recommend the use of the software to configure the router in your case.

  On the contrary, to connect to the router and use the link below to access and configure.

  http://192.168.1.1

  Default user name: admin or empty

  Default password: admin

• As a router WRT54GS cascading with IP fixed address block

  Hello

  I read several threads on the routers in cascade and the Knowledge Base, but none seems to fix my script with a router with fixed IP address block.

  My current setup is an ADSL circuit with a block of 8 fixed IP addresses. Of them the first xx.xx.xx.137 is assigned to interface the router, the second xx.xx.xx.138 for the router itself WAN xx.xx.xx.139/140/141/142/143 leaving as usable IP addresses. Connected to the ADSL circuit is that a D-Link DSL-G604T router with NAT disabled to allow IP addresses to be assigned to my web servers and ftp. Of course, DHCP is disabled on the LAN interface.

  Unfortunately, the transmitter wireless on this router is defective so I would my Linksys WRT54GS (Firmware v1.50.6) D-Link router cascade so that I can use it (with active DHCP) as a point of access for multiple wireless devices.

  This thought through to logically I've named WAN 54GS with one of the xx.xx.xx.140 to static IP address available, a subnet mask 255.255.255.248 and the door entry xx.xx.xx.138. I left the LAN settings like the beach 192.168.1.xxx and DHCP active. I then connected the interface WAN of the 54GS to one of the LAN connections on the D-Link with a straight ethernet cable.

  I can connect to the admin 54GS via a direct ethernet connection and wireless interface but not to the internet.

  I can ping that is the xx.xx.xx.140 of the interface wan of the 54GS since a laptop computer connected wireless but not the IP address of the gateway of the network xx.xx.xx.138. D-Link router.

  Am I missing some other settings in the router. Especially in the routing section advanced? I guess that the device must be set to a router rather than the bridge, but if there are parameters of dynamic routing?

  Any help would be appreciated

  Thanks Brickmonkey,

  Just thought I would update this post. I tried from you suggestions, but to no avail. The frustration I did a hard reset of the router D-Link and set it up again from scratch and... Hey presto it now works.

  I can only think that there may have been some settings left from when the router has been initially implemented for Nat and I had configured port forwarding. In any case it now works OK then thank you very much for your answer.

  Fozzie

• What wifi router works best with an iMac

  Please be nice to me I don't really know what I'm talking about, but really really need help.  We have an iMac with wifi connections and currently run a cisco linksys e1000, who is five years old at least, and I'm sure is very tired, either completely obsolete.  We have a lot of buffering when using our Apple TV and someone recommended to get a

  ASUS RT-N66U - 900Mbps router dual band Wireless-N Gigabit LAN/WAN, 2 x USB, printing FTP UPnP Server VPN, IPv6 to replace the Cisco.  It will work with our IMAC?  Do we need a separate thing called a modem.  If it won't work not please can any kind person recommend a router to update that works.

  Thank you very much

  Vicki

  Use the Apple Airport Extreme Base Station.  The modem is what connects the router to your cable service.

• SPA9000 Setup problem with FXS ports

  SPA9000 PBX, configured with two VoIP providers implemented voice-> 1/2 line parameters. A telephone is connected to the FXS 1 (or 2 FXS) port and able to choose the right VoIP provider when making outgoing calls.

  SPA9000 question is that once the outgoing call is established, does not meet the other numbers composed for the extension of the called party number. Same question when you dial a number where voice prompt responds to the call, offering the choice of activities, to choose the specific number. None of the input selection works as nothing is written on the dial.

  Located in the Canada. VoIP providers: freephoneline.ca & callcentric.com

  SPA9000 Setup:

  Software version: 6.1.5; Hardware version: 1.0.5(a)

  Voice-> SIP-> PBX parameters-> call routing rule: (<:L1>9xx. |) <:L2>8xx.)

  Voice-> SIP-> settings-> telephone numbering Plan PBX phone: ([89], S 11, 0 [3469] |) [89] 1 [2-9] xxxxxxxxxS0 | [89], 011xx. | ([89], xx.)
  Voice-> FXS 1 / 2-> Dial Plan: ([89], S 11, 0 [3469] |) [89] 1 [2-9] xxxxxxxxxS0 | [89], 011xx. | ([89], xx.)

  Voice-> line 1-> Dial Plan: (<>xx.) [Smiley here shows insetad of: and >]
  Voice-> 2-> Dial Plan line: (<>xx.) [Smiley here shows insetad of: and >]

  Voice-> regional-> ringtones of appellate courts:
  Tone: 350@-19,440@-19;10(*/0/1+2)
  Second tone: 420@-19,520@-19;10(*/0/1+2)
  Outside the tone: 420@-16;10(*/0/1)
  Prompt tone: 520@-19,620@-19;10(*/0/1+2)
  Busy signal: 480@-19,620@-19;10(.5/.5/1+2)
  Reorder tone: 480@-19,620@-19;10(.25/.25/1+2)
  Off-hook warning: 480@-10,620@0;10(.125/.125/1+2)
  Back ringtone: 440@-19,480@-19;* (4/2/1 + 2)
  Confirm tone: 600@-16;1(.25/.25/1)
  SIT1 Tone: 985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
  T2is Tone: 914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)
  SIT3 Tone: 914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
  SIT4 Tone: 985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)
  Tone MWI: 350@-19,440@-19;2(.1/.1/1+2);10(*/0/1+2)
  Cfwd-tonalite: 350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2)
  Holding tone: 600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)
  Tone of the Conference: 350@-19;20(.1/.1/1,.1/9.7/1)
  Ensure the Indication of the ringtone: 397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)
  Featured call tone: 350@-16;*(.1/.1/1)

  Hi @sglumac, it seems that your SPA9000 is a Cisco product. Please repost this at this link: https://supportforums.cisco.com/ for solutions.

• Reserve an IP address on a router from Linksys E1200

  Hi, I'm putting our Outback Mate 3 controller with a fixed ip address and the port forwarding on a router Linksys E1200.  So we can check on our wide network remotely.  I put in the DHCP reservation page and enter the ip address and mac address but when I go to save, it shows the hexadecimal value is incorrect.  Configuration of the IP address on the 3 Mate, it can only 192.168.001.xxx and reserving the address on the Linksys, it only allows reserve 192.168.1.xxx.  These are not values?  Any advice?

  Yes, they are the same. If it shows the hexadecimal value then most likely there to talk about the address.which of mac is in hexadecimal. Make sure the format matches and no additional spaces etc.