NB100 - OS uses only 500 MB of RAM - 1 GB memory total

Similar Questions

• After Effects using only 1% of the RAM

  Dear Adobe,

  My after effects uses only 1% of my ram 32 GB can I know how to increase this, I allocated 8 GB for other application

  Why my application showing.

  Please inform as soon as possible.

  Kind regards

  Knani

  

  

  Perhaps because it doesn't do anything?   When he starts using 32gigs of RAM to display the 'about' dialog that is at this time, you should start to worry.

• Hello! I have a 32-bit version of Windows 7 and I subscribed plan creative mgoe (CC 2015 Photoshop and Lightroom). Unfortunately when I try to use photoshop there is a ram (out of memory) error. I have a 8 giga of ram, and I have already raised the ph ran

  Hello! I have a 32-bit version of Windows 7 and I subscribed plan creative mgoe (CC 2015 Photoshop and Lightroom). Unfortunately when I try to use photoshop there is a ram (out of memory) error. I have a 8 giga of ram, and I have already raised the photoshop preference range.

  It seems that the installation of a 32-bit version of Windows is your mistake. This limits each app to not more than 2-3 gigabytes, no matter how much RAM you install.

• Windows 7 on Netbook Dell - memory-2 GB (1 GB usable) - why should I use only 1 GB of RAM? How can I make all 2 GB usable?

  I have a Dell Inspiron Mini 10v Netbook. It came with 1 GB of RAM and Windows 7 starter. Took me to upgrade to Windows 7 Ultimate and it's much better. Given that the memory was only 1 GB I installed a 2GB chip instead. The BIOS of the computer/is happy with it, but Windows 7 will use only 1 GB of it.

  Resource monitor scored the extra 1 GB has "reserved equipment." They have no reserved before the addition of the extra RAM.
  I want to use all my memory! Help!

  Hi pcstan

  I would like to know what version of the operating system are you using? It is 32-bit or 64-bit?
  You can try the following methods: -.
  1. change setting memory remapping in BIOS. This setting can have different names, look at the motherboard or computer manual.
  2. run msconfig.exe. Under Startup go to advanced options and change your maximum memory available.
  This can help you
  Concerning

  Vipul Taneja. http://www.vipultaneja.com

• SpeedGrade CC 2014.2 build 8.2x51 reading smoothing / jerky 4K with GPU R9 295 x 2 - it uses only 2 GB of RAM (8.1 Windows 64-bit), Mac OS - same problem

  Hello, guys

  I have following configuration:

  I7-5960 x 4.3 GHz

  32 GB DDR4 RAM

  ATI 295 x 2 8 GB (Gpusniffer.exe watch 3072 MB on each unit of Hawaii)

  Samsung XP941 Ultra M.2 (> 1000 Mb/s)

  Some 850 Pro SSD for H.264 4 k source

  Latest version of Speedgrade CC 16/02/2015 (DUAL MONITOR SETUP - 2560 x 1440 for Interface and 4096 x 2160 for previewing)

  I work with a lot of short 10-15 seconds 4 K 4096 x 2160 24 fps H.264 clips of Panasonic GH4. Import their first CC as some stabilization warp, cut them, save the project and opened in Speedgrade CC all are fantastic smooth in first CC.

  Speedgrade - a simple color - exhibition, some keyframes and simple scoring correction for certain substances. I use the GPU acceleration for sure have lots of 4096 x 2160 4K 24 fps. But it is not flexible and smooth after that a correction is applied. Everything is jerky and freezes the first seconds, when I press 'PLAY'. I used resources, the Manager monitor tasks (Winodws 8.1 64-bit) and Afterburner. And there's what I discovered:

  • Afterburner shows the use of mono-GPU (as we know it for playback only 1 GPU used) the same amount as in first. SpeedGrade CC use 2, 5 GB of VRAM. Also, if I use one zero effect - accelerating gpu, like "transform", for example, imported first, I get "not enough GPU resources" message in Speedgrade. Afterburner shows, CC Speedgrade tried to use more, and then Max 3GB available VRAM during that time. So I turn off these effects, before you open a project in Speedgrade.
  • CPU is low (15%) use, perhaps a little lower, then in the first CC
  • Disc - 3-10%, H.264 is weak on this subject
  • RAM! -is the problem. I have been authorized to use the 29 GB of RAM for Adobe apps. Speedgrade CC use no more then 2-3 GB according to the the Task Manager (for most 2 GB) and 8.1 Windows resource monitor 64-bit Pro. After I finished with the color correction, a project open in first DC, work with lumteri on smooth and! First CC use 9 to 10 GB of RAM to play the same music video in full resolution smoothly!

  
  

  I already reinstalled everything, including drivers for the GPU, 8.1 for Windows and Adobe CC even result.

  MacBook Pro 15 retina end 2013 with i7-4960HQ/16 GB of RAM/Geforce 750 m UPDATE!

  Under Mac Os Yosemite 10.10.2 - same situation here. First CC use 5 GB (of 11 GB of available) 4096 x 2160 Prores 422 HQ and is usable, smooth with a few drops of frame.

  SpeedGrade CC uses 2.5 GB RAM of 4096 x 2160 and it is impossible to use plenty of 4096 x 2160. Only 1/2 resolution of overview is smooth and usable on the screen of the laptop. 4096 x 2160 externally connected through Thunderbolt monitor, it's a lot rougher, I think it's hard for 750 m with 2 GB of VRAM.

  UPDATE! Previous version (CC 2014) of first CC and CC Speedgrade Windows 8.1 64-bit - even situation.

  
  

  What do you think?

  
  

  My opinion - Speedgrade CC is not optimized for 4K resolution. First CC is good for 4K.

  BTW, for more information, latest AMD catalyst driver 14.12 omega has a problem with my R9 295 x 2 and engine reading Mercury (MPE) OpenCL - just black with sound screen, when I turn on the GPU acceleration. So I use the previous version of 14.9. With 14.12 GPUsniffer.exe found a device with 4 GB of VRAM GPU and a GPU with 3 GB of VRAM (normally obligatorily 3 + 3 GB 295 x 2 Dual GPU radeon chip).

  Yes

  So, finally, Speedgrade CC works 95% smooth time with 4096 * 2160 H.264. But it was necessary to turn off all effects in first Pro CC. Nothing new. I found a few discussions on this fact, but after that I spent some time with experiences.

  Stabilizer Warp even alone is enough to make Speedgrade CC really agitated. 'Transform' effect simply blocks Speedgrade CC with "GPU resources.

  Each effect uses some VRAM (for Warp stabilizer 200-300 MB). After you have disabled all effects had load VRAM under/near 2 GB for the little clip 4096 * 2160.

  First CC flies simply with unique x 290 or 295 x 2 (which is the only x 290 during playback). Even 3GB VRAM available software Adobe CC.

  PS Macbook Pro retina 15 "with Geforce 750 M 2 GB VRAM would work smoothly with Prores to half a preview/playback resolution - 2048 * 1080. CC CC SpeedGrade or Premiere Pro with 1/2.

• Satellite Pro A60 - Windows XP shows / use only a part of RAM available

  Hello guys!

  I am facing strange problems with one of my two A60s. I just upgraded two of them with 1024 MB of RAM the same. One works perfectly, but the other will show me only 410 MBs in Windows. The BIOS indicates the correct size. I changed the RAM from one to the other, but this strange error is always present. The version of the BIOS has been updated to 1.90 and has Windows XP SP2.

  Do you have any suggestions or ideas? Is there an easy way to put the management of RAM in Windows?

  Thank you in advance!

  Ralf

  It s very strange.
  I found that an additional Satellite Pro A60 info has been delivered with a different hardware configuration.
  Some A60 Pro comes with an internal memory of 512 MB and others with only 256 MB internal memory.
  In addition, the internal memory modules cannot be deleted and there is only one slot for memory upgrade.

  But I put t know why the OS shows only 410 MB

  Oh, I forgot to mention that the graphics card, also use the part of the main memory and, therefore, the operating system of shared memory could indicates a value of different memory.

• operating system uses only not 4 GB ram

  I have Windows XP Professional installed on my pc, my bios says I have 4 GB or memory installed and usable. Where as my when I get into the operating system itself it only said that I have 2.0 GB used. My bios is up to date, I have other PCs that allow all of the 4 GB be used on the operating system, so I'm not sure why this one gives me the penalty.  Any ideas that would help?

  -asus a8n32-sli mobo
  -4 GB of ram ddr pc3200 400 MHz
  -geforce 8500 gt graphics card
  -amd 64 3800 +.

  Hello

  1. which version of the service pack is installed on your computer?

  2. don't you make changes to the computer until the problem occurred?

  The RAM reported by the System Properties dialog box and the system information tool is less than expected in Windows Vista or in Windows XP Service Pack 2 or later: http://support.microsoft.com/kb/888137/en-us

  Hope this information is useful.

• 10 32-bit Windows uses only 3 GB of RAM, despite a higher setting in VMware

  I just created a 32-bit Windows 10 virtual machine fees. No matter how I put the memory in VMware settings, Windows 10 reports that 3 GB of RAM.

  
  

  Why is configured for 4 GB of RAM?

  Here are the steps I took:

  * I've created and activated a new Windows 7 32 - bit (pre - SP1) since an installation DVD. This Windows 7 original had material v11, 2 hearts, and 2048 MB of RAM in VMware settings.

  * I mounted the ISO image of CD / DVD of Windows 32-bit and run 10 the installer of Windows 7. I did a "clean install" (do not store data, applications, etc.).

  * I updated Windows 10 entirely and the VMware Tools installed.

  * I changed the setting from memory several times to 6144 and 8192 MB, but nothing has changed.

  * I also changed hardware v12 and changed the type of operating system from Windows 7 to Windows 10.

  Despite the changes, 10 (32-bit) Windows reports only 3 GB of physical memory. I checked systeminfo (3071 MB), System-> settings (3.00 GB) and several other sources, and they are all auto-coherent to 3 GB.

  The Configuration of the system, advanced STARTUP Options, memory Maximum box is unchecked (disabled).

  Any ideas?

  Please take a look at VMware KB https://kb.vmware.com/kb/1014006 which explains the 3 072 MB limit, i.e. the reserve of memory of 1 024 MB.

  Article:

  PC architecture reserves a part of the address space that is less than 4 GB for PCI devices. This space cannot be used for system memory. Note also that this is one of the main reasons for clients not to recognize that all assigned physical memory.

  André

• CS 5.5 uses only 22% of my ram, but 100% of the CPU

  Hello

  I wonder why the ram usage is so low compared to the CPU in AE cs 5.5? I check the stats background when rendering that happens and it is said that 22% of my ram is used. Even to the end, only 22%.

  That being said, people here are recommending tons of ram, such as 32 GB +, but why? If this is the case? Maybe my computer needs more complex effects such as the production of grain?

  Thank you!

  The number reported at the bottom of the request for use of the RAM is only the amount used by the foreground application. It has nothing to do with how much is used by the instance of After Effects context or assistance process.

• Satellite A100-551 recognizes only 1 GB of RAM after upgrading memory

  Hello

  I just bought a memory of 1 GB of RAM to upgrade my Satellite 2 * 512 to 1 * 1024 + 1 * 512.
  The brand of memory is Crucial.

  Everywhere where I put my memory (1 GB in slot 1, 512 MB in the 2 slot or vice versa), my computer don't recognize only 1 GB.

  Some ideas on this concern?
  What I have to put the same size of memory in each slot, maybe?

  THX in advance for your help.

  Kind regards.

  SBL68

  If you only check this forum and search for RAM upgrade themes, you will see that the people who use essential modules reported on compatibility issues.
  If you want to upgrade to Ram successfully, please use the modules recommended Toshiba or Kingston.

  If you have to choose between price and compatibility compatibility and good work modules, you must choose. Compatible Toshiba DDR2 400/533 1 GB module followed the part number - PA3411U-1M1G.

  For Kingston modules, visit www.kingston.com/

  Good luck!

• My laptop has 4 GB of RAM, but uses only 3 GB?

  In Control Panel > all items in the control panel > system, under system, it is said: ' installed memory (RAM): 4.00 GB (3,19 usable GM).

  Why should I use only 3,19 GB RAM? And is it possible to use 4 GB of RAM?

  SB22

  The first reason can be that you are running a 32-bit system.  They can 'see' ~3.2 concerts

  The other reason is perhaps that your video card is using the rest as "shared" memory

  You can be nothing.

• Photoshop does not use the value amount of ram. Stuck at 6 GB

  Hey guys, recently started having issues with photoshop do not receive the fixed amount of ram needed. I have it set to use 24 GB of Ram (I have 32 GB) tried a reset, tried to reset back to the factory, then put it back, nothing. The strange thing is that if I put it to use only 1 GB of ram, it is still idling to 6 GB. Advice on how to approach this would be greatly appreciated I during the execution of projects that require a lot of attention.

  Thank you.

  Mac or Win?

  If you give complete and detailed information on your configuration and the matter in dispute, such as your platform (Mac or Win), exact versions of your operating system, Photoshop and bridge, specification of the machine, what troubleshooting steps you have taken so far, what you receive error messages if problems with opening files raw as the exact camera brand and model that generated the , etc, someone may be able to help.

  Read this FAQ to get advice on how to ask your questions correctly to get faster and better answers:

  http://forums.Adobe.com/thread/419981?TSTART=0

  Thank you!

• 2 slots for ram, or I can use only a single slot?

  Hello..

  IV ' e bought 8 GB of ram for my MBP 2012 has 4 GB of memory.

  But I totally forgot that she has 2 slots for ram!

  so you can use only a single slot? or I have to buy another ram?

  Thankss

  For best performance Mac need pairs of corresponding RAM modules, swap or buy more is recommended all things being equal. I would however expect sentencing of incompatibility performance much smaller than the benefit of the upgrade beyond 4 GB, so you could run with 8 GB in a slot and the original 2 GB in one for 10 GB total installed.

• Tecra A7 with W7-64 b uses only 3 GB to 4 GB of RAM available

  Recently, I upgraded my Tecra A7-243 with XP 32 b of 2 GB to 4 GB of ram.
  XP 4 GB has recognized and used as expected only 3 GB of RAM.
  Now, I have installed Windows 7-64 b (full installation with format system partition).
  But W7 reports still installed 4 GB memory of the whitch used only 3 GB.
  How can I force W7 to use all 4 GB of memeory?

  Hello

  The BIOS recognizes the full 4 GB of RAM?
  Also check DirectX (in execution type dxdiag).

  If the 4 GB of RAM would be mentioned here, so I guess that everything is ok with the notebook and the part of RAM is allocated by the graphics card.
  Stocks GPU, a part of the main memory... it runs automatically.

• Can I use all 500 GB on a hard drive, I have install windows 7 and it only uses I think 466 around this amount, why is - this

  Can I use all 500 GB on a hard drive, I have install windows 7 and it only uses I think 466 around this amount, why is - this

  Hello Edtannjr,

  Thank you for your message.  Remember that the operating system itself takes place and many OEM systems contains a recovery partition which can take up to a space as well.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.