Need help to connect to MySQL using dg4odbc

Similar Questions

• I need help to connect my macbook pro to my TV high definition. I just installed the latest update for el capitan, and now all of a sudden not work there.  I use a hdmi cable that has worked for me before.  Any suggestions?

  I need help to connect my macbook pro to my TV high definition. I just installed the latest update for el capitan, and now all of a sudden not work there.  I use a hdmi cable that has worked for me before.  Any suggestions?

  OS X El Capitan: use your TV as a monitor

• I need help to connect my iPhone apps on El Captian Office

  I need help to connect my iPhone apps on El Captian Office

  Without knowing exactly what you're trying to do, this article from Apple can help:

  Continuity allows you to connect your iPhone, iPad, iPod touch and Mac - Apple Support

• I need help to connect my used ipod touch. The previous owner did not mention that I needed their icloud account to set up my account icloud to the ipod touch.

  I need help to replace a previous owners icloud/apple id. So I can replace with my apple/icloud id, we use it and I was ignorant, I needed previous owners apple id replace it with mine. The previous owner just told me how to reset or to put in recovery mode, but the previous owners apple id needs to turn off find my iphone settings. If I can replace with mine. The difficulty. Help, please!

  You run into the lock of Activation

  Find my iPhone Activation Lock

  If you can't have the previous owner to do

  Turn off find my iPhone Activation Lock

  then back for a refund since yo cannot use the device. Apple isn't going to help.

  If yo cannot come back, turn the unit into the police because it is likely, lost or stolen

• Need help to connect my ibook G3 to the Internet using Airport

  Hello
  I recently bought an Ibook G3 and unable to connect to the internet using Airport. I can find my internet provider and it allows me to enter the password for it, but after I have get the same message:
  "An error has occurred all trying to join the selected airport network. -3151.
  the password is correct, so I don't know why its not connecting.
  I checked the map, and everything seems OK.

  the Ibook is a Mac OS 9.2

  version Mac OSZ1 - 9.2.2

  Help, please! -J' I feel like IM going crazy trying to get it to work

  .

  Older hardware uses a different protocol and the later models of wi - fi security, so

  It may be that the unit is able to see the signal available but not able to use it or connect.

  In order to set up an AirPort Base Station wireless vintage separate from any modern

  wireless local area network is a way to use a less secure configuration wireless computer older

  and without compromising the latest systems which would share a reduced security wireless

  If you want to reduce the overall security of the system (using the old protocol WAP,

  WEP, etc.; drafters WPA2 +) and base stations can be more difficult if they

  also have more than one type of signal. Older computers use less bandwidth.

  At this point, I cannot possibly be a great help; short of reading thanks to my favorites

  old pages (and check if the pages still work online) reference to use the installation program.

  My setup wireless WPA2 but earlier use AirPort Express base; and also have older

  base station AirPort Extreme 54 k White orb on-site; but not currently enabled.

  To have an additional wireless hardware for use with vintage computers.

  Good luck in this case!

• Need help, cannot connect to http sites, https only...

  BLUF: I can connect only to HTTPS Web sites, http gives me 'unable to connect to the server' or "no route to host" errors.

  While I was out of town, the woman finished downloading something on his MBP that cause a lot of pop-up ads any time during the use of the internet.  I ran Malwarebytes Anti-Malware and it found and removed a bunch of infected files.  All this while the computer was on OS X 10.9.x. Since that time, on any browser (firefox, safari, chrome) we can only connect to the https pages.  For example, http://www.google.com = no go "impossible to connect to the server...". ", while https://www.googlec.com = good, but unfortunately most of the links is http, so it is useless.

  I spent most of the last days 2 pouring on the forums, and troubleshooting to resolve this question... what I did:

  Reset my router (without success, all the remains connected to it is good (everything else is also Android/windows))

  Reset my modem (even had my ISP reset everything they could on their end too)

  Back to zero/reinstalled all browsers,

  erased the PRAM using the option + command + p + r at startup.

  verified that no Proxy box is checked in the advanced network settings

  tried to change the DNS, manual, auto, opendns, 8.8.8.8/8.8.4.4, using my ISP DNS googles, nothing changes.

  uninstalled all that was installed last week (not a lot, but now I don't know what it was).

  disabled the browser all extensions/plug-ins.

  IPv6 disabled/re-enabled (set to auto),

  What works:

  Safe mode, internet is full to the top.

  While in safe mode, I was able to connect to the app store (could not in a regular connection or guest user) and upgrade to OS X 10.11.5, but even the installation that does not solve all missing / corrupted files, I always have the same question.

  I thought for sure the new OS would have fixed it, but now I'm really stumped.

  Is there a way to reset completely all network settings? Could get blocked port 80 (http)? How can I tell?

  Any help would be appreciated,

  v/r

  Sean

  (a husband who knows enough about computers to really break, ha)

  First, never use any type of software "anti-virus" or "anti-malware" on a Mac. That's how cause you problems, not how you solve them.

  1. the present proceedings is a diagnostic test. It doesn't change anything for the better or worse and therefore, by itself, will not solve the problem. But with the help of the results of the tests, the solution may take a few minutes, instead of hours or days.

  The test works on OS X 10.8 ("Mountain Lion") and later versions. I do not recommend running it on older versions of Mac OS X. It will do no harm, but it will not do not much good.

  Do not be put off by the complexity of these instructions. The procedure is easy to do right, but it is also easy to do wrong, so I had very detailed instructions. You make the tasks more complicated with the computer all the time.

  2. If you do not already have a current backup, please back up all the data before doing anything else. The backup is needed on the general principle, not because of what anyone in the test procedure. Backup is always a must, and when you encounter any kind of problems with the computer, you can be more than the usual loss of data, if you follow these instructions or risk not.

  There are ways to back up a computer that is not fully functional. Ask if you need advice.

  3 here is instructions to run a UNIX shell script, a type of program. As I wrote above, it doesn't change anything. It does not send or receive data over the network. There is no to generate a report on the State of the computer human readable. This report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents for me or someone else.

  You should ask yourself if you can believe me, and if it is safe to run a program at the request of a foreign national. In general, no, he's not sure, and I encourage it.

  In this case, however, there are ways for you to decide if the program is safe without having to trust me. First of all, you can read it. Unlike an application that download you and click to start, it is transparent, anyone familiar with the code can check what it does.

  You may not be able to understand the script yourself. But variations of it have been posted on this site several times over a period of years. One of the million registered users to have read the script and set off the alarm if it was dangerous. Then I wouldn't be here now, and you would not be reading this message. See, e.g., this discussion.

  However, if you cannot satisfy yourself that these instructions are safe, do not follow them. Ask other solutions.

  4. here is a general summary of what you need to do, if you decide to go forward:

  ☞ Copy text from a particular web page (not this one) to the Clipboard.

  ☞ Paste into the window to another application.

  ☞ Wait for the test to run. It usually takes a few minutes.

  ☞ Stick the results, which will be copied automatically, in a response on this page.

  These are not specific instructions; just a glimpse. The details are in parts 7 and 8 of this comment. The sequence is: copy, paste, wait and paste it again. You don't need to copy a second time.

  5. try to test in conditions that replicate the problem, to the extent possible. For example, if the computer is slow intermittently, run the test during a downturn.

  You may have started up in safe mode. If the system is now in safe mode and works pretty well in normal mode to test run, restart as usual before running it. If you can test only in safe mode, this.

  6. If you have more than one user and a user is affected by the problem, and the user is not an administrator, and then run the test twice: once under the affected user and one administrator. The results can be different. The user that is created automatically on a new computer, when you start it for the first time is an administrator. If you are unable to log in as an administrator, verify that the user concerned. More personal Mac have only one user, and in this case this section does not apply. Don't log in as root.

  7 load the linked web page (the site "Pastebin") in Safari. Press the combination of keys command + A to select all the text, then copy it to the Clipboard by pressing command-C.

  8. start the Terminal application integrated in one of the following ways:

  ☞ Enter the first letters of his name ("Terminal") in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Click anywhere in the Terminal window to activate it. Paste from the Clipboard into the window by pressing Command + V, then press return. The text that you pasted should disappear immediately.

  9. If you logged in as an administrator, you will be prompted for your login password. Nothing displayed when you type. You won't see the usual points instead of the characters typed. Make sure that caps lock is turned off. Type carefully, and then press return. You can get a warning to be careful. If you make three unsuccessful attempts to enter the password, the test is still running, but it will produce less information. If you do not know the password, or if you prefer not to enter, just press back three times at the password prompt. Yet once again, the script will run.

  If the test takes much longer that usual to run because the computer is very slow, you can be prompted for your password a second time. The permission you grant by entering it will expire automatically after five minutes.

  If you are not logged as an administrator, you will be prompted for a password. The test will run. It just will not do anything that requires administrator privileges.

  10. the test may take a few minutes to run, depending on the number of files you have and the speed of the computer. A computer that is abnormally slow may take more time to run the test. During execution, a series of lines is displayed in the Terminal window like this:

      Test started

          Part 1 of 4 done at: … sec        …        Part 4 of 4 done at: … sec

      The test results are on the Clipboard.

      Please close this window.

  The intervals between the parties will not be exactly the same, but they give an approximate indication of progress.

  Wait for the final message "Please close this window" appear - again, usually within a few minutes. If you don't see this message in about 30 minutes, the test probably won't be completed within a reasonable time. In this case, press the Ctrl + C key combination or the point command to stop it. Then go to the next step. You will have incomplete results, but still something.

  In order to get results, the test should be allowed to perform or be stopped manually as shown above. If you close the window of the Terminal, while the test is still running, the partial results will not be saved.

  11. when the test is completed, or if you manually stopped, leaving the Terminal. The results have been saved to the Clipboard automatically. They do not appear in the Terminal window. Please do not copy from there. All you have to do is start a response to this comment and then paste it again by pressing Command-V.

  At the top of the results, there will be a line that begins with the words «Start time.» If you do not see that, but rather to see a mass of gibberish, you wait for the message "close this window". Please wait and try again.

  If personal information, such as your name or e-mail address, appear in the results, make anonymous before posting. Usually it will be not necessary.

  12. in the validation of the results, you see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the software which manages this website. Thanks for posting the results of the tests on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

  13. When you are finished with the test, it is gone. There is nothing to uninstall or clean.

  14. This is a public forum and others can give you advice based on the results of the test. They speak for themselves, not for me. The test itself is harmless, but all that you can not be. For others who choose to run it, I do not recommend that you view the results of test on this Web site unless I ask.

  15. the related UNIX shell script is a notice of copyright. ASC readers can copy for their personal use. The whole nor any part can be redistributed.

• p6677c: need help to connect 7525 Photosmart wireless desktop

  Hi all

  I would like to sent to print on my printer 7525 jobs. I have this printer for some time and when I tried to use wireless until I couldn't go wireless. I just thought that I would connect it later, then gone usb. I would like to be able to use the fax feature would therefore to get the usb cable.

  I spent many hours trying to get this thing to print from the computer, but I am running out of ideas and need someone to guide me with some good info. I thought that I had bought a new printer but noticed today that this printer has a sticker saying it's renovated factory. This is perhaps why I can't make it work.

  I have performed the Assistant (s) in the computer and the printer, the printer prints the information that make you think it works. The computer I think is correct. Will the message print to spool it print pending, but does not print on this printer.

  If you have any suggestions please let me know what they are. I know best, one is to throw it in the dumpster to trash. I don't plan on it earlier. I can use it on USB.

  Thanks for any help you can provide.

  Hello

  First of all our computer does NOT have wireless card, why you can not connect.

  http://support.HP.com/us-en/product/HP-Pavilion-P6000-desktop-PC-series/4269976/model/4337127/document/c02547556/

  Your machine has taken a mini spare card so you can add a wireless PCIe card to your computer such as similar:

  http://www.scorptec.com.au/product/Networking_-_Wireless/PCI_Express_Cards/44759-TL-WDN4800

  After that, you can connect your computer to your wireless network and run the installation wizard again. At this point, you can simply select convert USB wireless.

  Kind regards.

• New on routers... Need help pls connect with Primus d-link

  Hi all, I'm new here. I am a complete newbie to routers. I just got a Linksys WRT54GL. I managed to plug it in and it works but lost my phone service Primus IE D-link (KVD-1120).  I had going from modem to the Linksys router this router for the d-link has however led to d-link and phone does not work.

  I called Primus and after waiting on my phone cell phone $20 and 1 hour and 20 minutes later, they were no help other then to tell me that the modem must be connected directly to the D-Link and that somehow, I had to find a way to connect the Linksys router for the D-Link (only 1 WAN and 1 Ethernet port on the back (a).

  Someone along the way also told me that I had to reconfigure certain ports or open some more. I don't know how or what is the same.

  If someone is able to help, I would appreciate it so. Please guide me through it, I don't know how to find the ip address is if I need to do. (read that somewhere)

  Thanks in advance for your help and your patience

  If your Modem is already connected to the D-Link router and your phone is also connected to the D-Link router, because your D-Link router has only 1 WAN and 1 LAN Port, then you can connect the ethernet cable between the LAN Port of the D-Link router to the Internet Port on the Linksys router and configure all the settings on your Linksys router.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...

  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...

  Change the mode of WPA wireless security, encryption, select TKIP. Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and do not forget the key.

  NOTE: The password must be more than 8 characters...

  Once you are done with the settings on your Linksys router, unplug the power to the router Linksys, D-Link router and your modem... Wait 30 seconds and turn on the power to the Modem first, wait until all lights are the lid, then connect the power supply to the router D-Link and after 30 sec connect the power supply to the Linksys router.

  Now, check if you are able to go online from the Linksys router.

• I have an audio bar that I need help for connection

  I was given a computer from a friend.  It is a Dell with a Dell monitor & bar audio.  The audio bar has a cord with a series male connector 9-pin.  The soundcard on the computer has 26 pins taken on this & I guess she must have and adapter to be connected, but have searched the Internet and have not found a. She told me that she uses this bar with his computer, but is not what I need to plug it.

  Thanks a lot for all your help.  I appreciate it.  I guess we can close this now.

• Need help to fix a computer using the command prompt

  So, my computer has suddenly crossed an escalation of alarming events, culminating with a very desperate, me trying to get information on the "Command Prompt". I don't know why, how, and it's all heart-wrenching. If someone has an idea of what could be done to fix it, I'd certainly eternally grateful to them. I will try to be as detailed as possible, so I don't miss information that might be useful for someone who know how to use.

  I have an Acer Aspire V5 - 573G, running under Windows 8 64-bit with a 12G RAM, about 1 year and a half old, and this is the story of his unexpected collapse.

  3 days ago the computer suddenly began to show extreme problems with the help of any program. I had let him sleep for a few hours, and when I came back all started running very slowly.
  At the beginning I'm not too worried about I have mostly ran programs dependent on Internet and thought it was a simple connection problem. I have conducted a malware check (which I use quite regularly anyway) and downloaded Avast to see if he could detect all viruses, but everything was fine.

  However, after that them stopping and turning back on the morning, things only seem to be deteriorating. I was not using my computer much at all, but after the second day of the fight with all that I realized that in Task Manager, something was really wide, and the drive was 100% use even when nothing was running.
  Usually, after a few minutes it would go back down to 1-2%, but as soon as I ran whatever it is, even simply open Control Panel, happen very quickly to 100 times (sometimes the Task Manager was sufficient to make this happen).

  I removed Avast and tried to delete the process when I made sure it was safe to do so, but it did not work. I tried after tutorials on the Internet for people who reported similar problems, which led me on a desperate journey funny through Windows Defender removal, an (unnecessary) extreme increase virtual memory (which I brought to the standard after that report maybe just made even slower computer), something to change the parameters of High-Performance mode so that the Hard Drive would never turn off has tried to stop the search and indexing in my session, make a small altar to Turing... nothing worked.

  I ran a chkdsk /f C: who found problems with indexing files / indexed and likely fixed, because when I ran simple verification once the computer has been again this topic found no problem. However, the situation was the same: essentially constant use of the disk of 100% and no way out.
  A sad moment, after hours of attempts, I stopped by mistake the wrong process, explorer.exe. I restarted the computer, and then the problem was still there, at least explorer.exeseemed fine.

  However, when a few minutes later, I rebooted the computer, even once, I couldn't access the desktop more and I found myself in a loop of reboot attempt that has nothing, attempted to retrieve an earlier version of the system but nothing happened.

  The only thing I can do is access chkdsk to see what the problem is, but I'm not sure that I could see a way out of this, even if there was a. The only thing that seems clear is that there is a lot of damaged clusters, that he can't solve.
  This morning I ran 2 other chkdsk /f c:, the results by saying that there was no problem and no further action was required.
  So I ran a C: /R, and once again he told me that there are some clusters damaged in this file.

  Is there something I can do? Someone has an idea of what could have happened?
  My idea was to wait for it to perform this check, run a chkdsk /f /r c: and see how it goes if I restart it, but I could really use advice from more experienced and skilled people.

  The computer has not received any physical damage, not even in the relatively distant past of her young life. Before he started having all these problems he did nothing particularly requiring either, just running a few innocent Assassins Creed II (with 11.9 available RAM for what I remember stats and a Nvidia GeForce GT 750 M, I think not that it should have been a source of so much distress). This is the first time it gives me problems.

  Also, I apologize if any information was unclear or confused, but not only am I a tragedy with computers, I also use a computer in a different language and a few technical terms could have been translated a little too big. If someone needs more information, I can do my best to give it.

  Hello

  Windows Defender is the default Antivirus which comes with Windows 8 and should not have been "removed."

  @@@@@@@@@@@@@@@@@@@@@@@@

  Reinstall your operating system:

  Here are the instructions Acer for recovery to factory settings, new condition.

  "Using Acer eRecovery application to restore your system or to create a recovery media.

  http://Acer.custhelp.com/app/answers/detail/A_ID/29934/~/use-Acer-eRecovery-application-to-restore-your-system-or-create-recovery-media

  See you soon.

• Need help to connect a microphone to the hearing

  Hello!

  I am having trouble doing something that seems very basic. I can't set up my microphone to record in the hearing. I am a total newbie to any form of sound recording and don't know anything about. I'm going to be as specific as possible to help someone help me.

  I recently bought a microphone condenser Neewer NW-700. I have it running in a mixer Behringer Xenyx 802 via XLR to 2.5 mm (with a 3.5 mm adapter). Mixer does not have a USB connection so I ran it on my computer (Macbook Pro running OS X El Capitan 10.11.3 at the end of 2011) through a Behringer U-Control UCA222 USB Audio Adapter RCA.

  I went into Preferences > hardware Audio selected USB Audio CODEC for my default entry and exit and did the same thing in the settings of the sound of my Mac.

  When I went to Audition for record, the wave was flat and I could not hear everything that comes out of the speakers. I went to the Audio devices page on my Audio Setup and lunch where I was able to adjust the volume of Audio Out but not Audio In.

  This is as far as I'm away. I've been Google searching for about a week now and nothing has worked. I'm not sure it's a computer problem, a hardware problem or a hearing problem -as I said, I don't know anything about this kind of stuff.

  I appreciate all the advice. Thank you!

  I just googled your microphone and ryclark is spot on.   The XLR Plug to 3.5 mm cable included with microphone is completely useless - there are several videos that appeared on my taling research on this subject.

  You need an XLR - f for XLR - M cable to connect on your mixer, turn on the Phantom, follow-up instructions that I proposed above.

  I also write a letter to Neewer asking a discount because they provide a cable can possibly use.

• Need help to connect a HDMI TV to my Satellite P70-A01C

  Can someone help me with the connection to a HDMI TV to an Australian TOSHIBA SATELLITE P70-A01C PSPLPA-01C002 running under 64-bit Windows 8?

  I'm on vacation in Thailand and tried to connect my new laptop to a TV using the HDMI, so the kids can watch their films, but the laptop refuses to recognize TV as an external monitor.

  I can't see anything in the windows which relates to a HDMI connection.
  I tried to detect the TV as a monitor in the Panel and had no luck.
  Outside the Mobile PC screen which is the screen of the laptop I have NVIDIA GeForce GT M 745 and Intel(r) HD Graphics 4600 as outputs available display, but none of these will detect the TV.

  I'm looking in the right place to connect the HDMI TV?
  The TV is a TV color LCD of Toshiba model 32PB2T for the Thailand.

  I don't know if this is important if the laptop is Australian and the TV is the Thailand, but my old Toshiba laptop running Vista that had no problem detection Australian TVs HDMI. This laptop doesn't seem to like it or Windows 8 t - it another way.

  Any help will be appreciated.

  Firstly, it must connect the two machines (laptop and TV) with an HDMI cable.
  Then turn on the TV and the laptop.
  In the settings of the TV, select the HDMI input port where is connected the laptop.

  Now, you can use the function key F4 (or Fn + F4) to move to the external video output, which in your case should be the TV device.

• Need help to connect to Hotmail from cell phone

  I have AT & T Wireless and a Samsung A877 Impression, a non-smart phone I use to access the internet through the Media Net.  For more than a year on this phone, I checked my Hotmail email on the phone.  My information has been saved so I access immediately to the pressure of Windows Live Hotmail.  On Sunday, when I pressed her, she forced me to my e-mail and password.  I tried 20 times but every time he says "the e-mail address or the password is incorrect. Please try again. "However I am able to connect with the same information on a computer, so I don't know the information"is correct. "I tried to erase the cookies, cache and history on the phone and it still will not let me log.  I'm frustrated and have looked for answers on the internet with no recent investigation of related problems.  I thank you in advance for any help, you can be able to give me.

  Hi Stacey71,

  This forum is for comments on the Microsoft Answers site.  The question you posted would be better suited for the center of Windows Live Help Solution.  Please visit the following link to post your question:

  http://windowslivehelp.com/forums.aspx?ForumID=8f4140fb-0bd7-463e-a8ec-560a73213017

  I hope this helps!

• Need help to connect the old Windows XP to new wireless router, please

  Hello
  I have an old desktop running Windows XP Edition family 2002 version, which has been connected to a Netgear WG311 802.11 wireless router g. I was unable to connect to other computers, so I replaced the Netgear with an E1200 Linksys wireless router. Now, all other computers find the Linksys router, but the older Windows XP desktop will not (because I don't use it to configure the router?).  How to connect your old computer to Windows XP to the new router, please? Thank you very much for your help.
  Walt

  Hello
  I have an old desktop running Windows XP Edition family 2002 version, which has been connected to a Netgear WG311 802.11 wireless router g. I was unable to connect to other computers, so I replaced the Netgear with an E1200 Linksys wireless router. Now, all other computers find the Linksys router, but the older Windows XP desktop will not (because I don't use it to configure the router?).  How to connect your old computer to Windows XP to the new router, please? Thank you very much for your help.
  Walt

  The problem is probably that the Linksys E1200 is a wireless-N Router and your former Office no doubt has a wireless adapter that is only capable of wireless-G (or perhaps Wireless G and B).

  Are adapters wireless in your other computers wireless - n?  If so, it perhaps is the reason why they could not connect to your old G of Netgear wireless router.

  You can get a new wireless-N for the office adapter or configure the E1200 wireless g available.

• HP PhotoSmart C4780: need help to connect to new router

  I have a HP Photosmart C4780 all-in-one. All the SW downloaded from HP. worked before but I just have to move on to a new Netgear wireless router. Read the previous replies to forum, but nothing seems to work:

  1. print the HP Network Configuration Page, but the URL says: http://0.0.0.0

  2 tried the WPS button on the printer and the router option, but it times out every time, never connect.

  3 tried the PIN option, but ends with the same result.

  4. I don't have the USB cable anymore, otherwise I would simply use it to connect momentarily.

  5. sometimes there is no time-out, and the printer displays the mention 'WPS error'

  I have Win 7 OS. How the hell can I connect?

  According to the document below the link, one of the conditions to connect the printer to the wireless network is a USB cable. I'm sorry, but it seems that you need to get a to put in place with.

  Installation of the printer software for a network connection Wireless (via an Access Point)