Need remote, power supply, A / V cable and IR transmitter

Similar Questions

• do you need a power supply to the current entry with data acquisition or 9265

  Hello I just receive the NI 9265 Daq for research in my lab. I'm trying to present entry and display it on an oscilloscope. I don't get anything. I did some research on the internet, so my question is do you need a power supply to the current entry with data acquisition or 9265?

  Read the data sheet.  Clearly on the first page is a sentence which reads "the NI 9265 requires 9 V to 36 V external power.

• H8 1414 HP envy. Need more power supply to run a better graphics card

  H8 1414 HP envy. Need more power supply to run a better graphics card. I don't have that power 300 watt need more someone knows a number of room and the place to get one that fits? I know that windows 8 makes it difficult, I am ready to install windows seven anyway.

  Nick, welcome to the forum.

  You can use any standard ATX power supply unit (PSU).  I always recommend measuring the PSU existing and comparing measures to whichever you choose, however.  I love Corsair products.  Also, I recommend at least 500W; 600W is even better for future updates.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP g60-440us think needs new power supply

  I am a computer SCIENCE student, have a laptop HP g60-440us, needs new power supply.

  Do you think that the replacement of the it's an ideal first project?  Please inform honestly.

  Thank you

  It is quite another thing. It is not an internal power supply but the power module.

  This is the part you need:

  part

  It is the repair:

  Manual

  You don't need to weld anything. You open the laptop, remove the old module and replace with a new one. Not too difficult though as it takes concentration and following the manual and keep track of which screws go where. It is a very good first laptop repair project.

• 1V - 5v linear output using power supply 5v, voltage divider, and variable resistance

  How can I get 1v - 5v output linear using power supply 5v, voltage divider, and variable resistance?

  Have the you wired as an attachment?  Using my schema, you can calculate the current flowing through the pot based on the fall of the tension in the pot

  4V / 10Kohm = 0.0004

  Kirchhoff's current law, we know that the same current flows through the circuit so now we can calculate the leg below the wall, based on the current and the fall of desired voltage across the resistance

  1V / 0.0004 A = 2.5 K Ohm

  My scheme maintains the current flowing through the circuit of constant, so the voltage divider must never change.  Assuming a linear pot, you will get a swing of such linear voltage as measured at the wiper.  If you wired the pot, a different way, then more then likely, you change the total resistance of 5V ground that would have the common effect that would effect the tensions.

• I have a Microsoft Broadband Networking Wireless Base Station. MN-700. I need a power supply. I want to know if it is 12 v ac or dc

  I have a Microsoft Broadband Networking Wireless Base Station. MN-700. I need a power supply. I want to know if it is 12 v ac or dc?

  I expect 12 VDC...

  That said you will have to also make sure that the polarity of the plug of the adapter is correct, IE. Center positive or Center negative.

  http://en.Wikipedia.org/wiki/Polarity_symbols

  These guys here claim to have one available for sale...

  http://www.unitedsale.com/AC-adapter-for-FA-4A110-Foxlink-12V-1A-Microsoft-MN-500-MN-700-router-brand-New_p_329.html

  As Mike well your really better off upgrading to a newer device that would support encryption WPA2 IMHO...

• Need new power supply for my HP p6210y

  Hello

  I have a HP p6210y (http://support.hp.com/us-en/document/c01859864) and I need to upgrade the power supply for the Radeon HD 4890 I have now. I am reviewing the PSU below. However, the dimensions are actually smaller than my current diet. Who's going because of my problems in terms of ride it properly in the case?

  http://www.Newegg.com/product/product.aspx?item=N82E16817338038

  If this will cause problems, can anyone suggest a power supply (it's the exact size as my current) which would be suitable for my graphics card. I need "500W with two connectors to power 75W 6-pin PCI Express.

  Thank you!

  I believe that the PSU is designed for a different style of the case. Discover the Corsair CX500, or CX600 power supplies. They are highly recommended and are favorite forum. In addition, they are only slightly larger than the stock power supply HP and are known to adapt.

  Frank

• PartNumber need to power supply of the Satellite A100

  I have an Equium A100-338, PSAAQE 006008AV model number. Power supply is PA3469E-1AC3. On Toshiba website element is not found. What is the correct/replacement/charger to power?

  Hello

  What do you want exactly? The you´ve of modelnumber displayed is correct both what the problem? If you want to buy a new one, you can check this site for example:

  http://www.freefixit.NET/ukstore/index.php?CATID=31517

  Otherwise, you can also try the PA3378E 3AC3 modelnumber.

  Welcome them

• Can I use a PXI-6224 with the SCB-68 to take the measurements of 4-wire RTD, or do I need a power supply separate?

  I suspect I already know the answer to this question:

  I have an PXI-6224 M-series data acquisition card and a terminal of the SCB-68 block and want to take action using a bunch of 4-wire RTD. Is the power to the power source for these measures 6224, or is - not possible with the hardware I have?

  I know that NEITHER you propose other solutions to my problem: I am interested to know if I can do these measures with the device that I currently have on site.

  Thank you!

  Hello Jeffrey,.

  You have two options here, but it doesn't look like you need some hardware.

  The SMU-4357 built conditioning of signals, but it will not work on the chassis curent you have:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/210596/

  We also have an option with the NI 9217 cDAQ, but once, it gets you into a different platform:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/208804

  We used to have an option that we sell no more - the SC-2042RTD. If you are lucky and have one of them on hand so here's some info:

  http://digital.NI.com/public.nsf/allkb/4FF2C0F8D11B99B486256F4C006DCEA0

  You can also use these two elements in conjunction with eachother with your current PXI card:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/12311

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/10778

  Finally, you could get an SCXI chassis and drop them in:

  http://sine.NI.com/NIPs/CDs/view/p/lang/en/NID/201609

  Thank you

  Joel C

  Technical sales engineer

  National Instruments

• No alarm beep when you disconnect the power supply a L530 cable?

  With my new ThinkPad L530, I get bored of the beep when the power cable is disconnected. So far, I found no option to turn on the alarm. This feature has been removed completely?

  
  

• Need help for upgrade power supply for HP H8-1445

  New computer.   system comes with 460w PSU.   I've updated the video card to a card that was recommednations 460w PSU.   has decided that I want to go with Radeon 6870 or better and needing a new PSU.

  Would appreciate any advice on the power supply up to 600w and directions for R & R power supply.   I would like a PSU that will bolt to the space used by the psu factory.

  Hello

  The Corsair PSU may be revised on the Corsair website.

  The CX series, all seem to have the same physical size as the typical ATX HP power supply power.

• Pavilion m9400t CTO: connection cable of the power supply to a Pavilion m9400t CTO

  I installed a replacement PSU which has more cables and a few different - no problem on the identification and plug 20 + 4, 4 + 4 on the MB.  Also, no problem connecting to the SATA cables for drives (HARD drive and two optical drives).  There is a PCI-E cable, which without doubt, I do not for my graphics card NVIDIA to address (original) does not have a connector to it.   But I am confused and I want to be sure, I'm not spoil, I have another cable with connector Molex 4, nowhere I see to connect.  Without doubt, it is for the power supply of the fans and other devices - my PC feeds its fans of the power supplied to the motherboard? Can I just ignore that cable operators, for now?

  Hello

  If you're implying that all your existing devices have power wires going to then simply ignore them the molex connector 4-pin.

• HP M9340f and Power Supply Upgrade graphics card

  HP dear community,

  I read some of the forums on the upgrade of the 9500gs it's an old graphics used for the HP M9340f. It's been 4 years now and the computer still works very well. I need advice for the upgrade on the graphics card.

  My specs are: http://support.hp.com/us-en/document/c01465973

  I know that there a 350W power supply. I am worried because the 9500gs video card has a connector that is powered from the motherboard, it has 2 pins (black and white wire). I read about the update for the ATI HD 5670 Nvidia 440 or 450. I know it is very old, but the 9500gs is still able to run modern games.

  The recommendations would work due to the connector 2 pin?

  Upgrading power supply help, because I think the video card is to select the power supply to the motherboard and not directly from the power supply.  I'm still confused on what the black and white wire, it is connected to the video card.

  I don't mind getting a greater electric power because I can get a better card. Just concerned with the black and white wire.

  I also read here that this person was able to exchange his power supply and graphics card for a gtx 560 ti and a 550W power supply. Its model is newer than mine. http://www.tested.com/forums/PC-and-Mac/8692-seeking-upgrading-graphic-cardnew-computer-advise/?&p=1

  I am really limited?

  Thank you

  Abe

  Swarl3s,

  We will divide your questions.

  (1) black/white is audio Spdif. Asus Nvidia supports a S-video port, audio is provided by the additional wiring.

  Now that the concern you had as answered (the whitw/black wiring), Let's proceed to the card.

  (2) what are your expectations of game? WOW, Diablo 3. Each has a recommended graphics card and each graphics card recommended the power of the power supply. Always add a tolerance.

  Regarding the GTX560Ti and a combination of 550W PSU, I see no problem. Then again, see here for more information and suggestions.

• Power supply and graphics card for p6230y

  I have a pavilion p6230y.

  There is no PCI-express slot, but I'm looking for update in the radeon HD 6850 with the new power supply.

  power supply - http://www.newegg.com/Product/Product.aspx?Item=N82E16817139023

  graphics card - http://www.newegg.com/Product/Product.aspx?Item=N82E16814121419

  they work on my desk?

  Thank you!

  The graphics card will be fine, but the power supply may cause problems of space because of the type of power supply (non-modular).

  The OEM case, you should look at modular PSUS. With modular units, you don't have to figure out what to do with all the extras, the unused connectors and wiring. Modular units you come a connectn those needed.

  This OCZ ModXStream Pro 600W Newegg should be perfect. I used power supply, OCZ for years and never had a problem. It is actually less expensive than the Corsair you asked.

• HP Pavilion Elite m9340f replacement video card and power supply

  Hello

  I bought my HP Pavilion Elite at Best Buy m9340f in 2009 and brought it to the Venezuela where I live now.

  My video card, started making the noise of the typical fan geforce 9500gs can do. The temperature of the gpu is very high (from 73 ° c without playing or watching videos!), and I'id like to replace it as soon as possible before my material fails completely.

  But the power supply 350w, to replace any video card decent needed to change my diet too. I have not the slightest idea of what type of power supply should I buy, and if I should replace the case too. My intention is to keep my cpu, my mother, my hard drive and my ram (purchase of a new system to the Venezuela is out of the question because of the barbarian prices in this country).

  Then to take the questions in order, I'll here:

  -I want another video card (geforce 9500gs is known for his failure, so I want to upgrade to a more powerful card)

  -To do this, I need another power supply, so I need recommendations on the provision of market models which CORRESPOND to my HP Pavilion Elite m9340f or

  -replace also the case: what kind of business should I need that corresponds to the motherboard of benicia

  Thanks in advance

  Jeronimo Ramos-Prince

  The information below was previously published by Big_Dave in response to several other posters about their questions about GPU upgrades. Prices shown are in U.S. dollars and for American retailers.

  Your PC has a 350 Watt PSU if below video cards will work:

  $50--->NVIDIA GT 430 9.6 Gbps - single slot width

  $65--->NVIDIA GT 520 8 Gbps - single slot width

  $80--->NVIDIA GT 440 25.6 GB/s - single slot width

  $130-->NVIDIA GT 545 43 Gbps - location single width - could be hard to find but perhaps only in the store

  $110-->NVIDIA GT 240 1 GB DDR5. 54.4 GB/s - single slot width. This card does not support DirectX 11 which is eventually used in some of the latest PC games but it's a great performer.

  Review the performance of NVIDIA specifications. Look at the specifications of strip memory bandwidth and level of DirectX support.

  I normally don't recommend video cards AMD for PC with a 350 Watt power supply as AMD provides 400 watts or more for most of its video cards.

  Frank