need to press the pause button to start win7 on hp g62

Similar Questions

• Satellite P875 - need to press the FN button to use the function keys?

  Hello

  I have a W7 Satellite P875 running and something weird just started to happen.

  My F1 - F12 keys and reverse obtained special functions.
  I used to need only press the buttons for special functions and now I need to press "Fn" otherwise I get the regular F1 - F12 options.

  I checked the system at startup and then setting it always says the special functions are those by default, but this isn't the case. I tried switching between the keys F1 to F12 and special functions as value by default, but little matter I do only the keys F1 to F12 are the default ones.

  Any solution or any driver I have to re - install to make it back to normal?

  I must say at the same time, I started having problems with my iTunes library with conflicts, I think with my AVG Antivirus. Suffice to say where there is a known conflict between AVG and the system that could influence that. I was also messing around aound with msconfig to try to sort that conflict but I returned to the way it was then it should not be the cause.

  Hello

  This is controlled in the BIOS as well as it can be changed in the settings of ToshibaHW.

  Also, go into the BIOS press F2 at the beginning.
  Now choose Advaced and here you will see the point of the System Configuration.
  Go ahead and finally you will see the option called:

  * Function Mode button (without pressing the FN key) *.

• Need to press the F1 key to start windows

  Whenever my computer is started or restarted also it takes a long time to get up and running, then I get the message:
  Primary drive 0 not found
  * (30 second break)
  Strike F1 key to continue, F2 to run the Setup utility

  Im running Windows XP, 3gig Pent 4, 800, 2.5 GB RAM bus speed. Any new 500gig hard drive SATA, from 500gig external HARD drive. I had to do a clean install of the operating system, after the system crashed after that automatic updates are released a few weeks before.

  Hello
  Press f2 go to settings
  Look for the boot sequence tab
  Make sure the folder c: / starts first

  Please click on the check mark as answered check on this Page if this post solves your problem, because it helps people who need quick access to answers THANKS AND GOOD LUCK

• My his laptop makes a beep when I press the power button / stop and it does not start

  Hello

  I bought a new Dell Inspiron 15z touch ultrabook and when I pressed the power button, it starts to beep and won't start. The screen is totally blank. What should do? Help, please

  -Mayur gala

  Hi Mayur,

  Welcome to the community,

  Sound signal can be used as a diagnostic indicator. The computer may emit a series of beeps at startup if errors or problems. This series of beeps identifies a problem and is called "beep code".

  See the table below which shows the beep codes and the possible problem:

  Overview of beep Code
  Beeps	Description	Possible cause
  1	ROM BIOS checksum failure	The map system, covers BIOS corruption or errors ROM failure
  2	No memory (RAM) detected	Memory or memory slot failure
  3	Chipset error (North and South Bridge error) Time-Of-Day Clock test failure Gate A20 failure Super i/o chip failure Keyboard controller failure	System board failure
  4	Memory read / write failure	Memory failure
  5	Real Time Clock (RTC) power failure	CMOS battery failure
  6	Video BIOS	Video/smart card failure
  7	Failure of the CPU	Processor failure
  8	LCD SCREEN	Failure of the LCD

  Let me know if you need assistance.

  Thank you

• 15 170tu ac: I HAV to press the power button several times to start the laptop...

  I HAV to press the power button several times to start the laptop... works well with the power supply on.

  all My drivers & bios is updated... but when I opened the lid... I HAV poer press several times the button and he then began 4-5 min.

  Hi @Vishalwagh123,

  Welcome to HP's Forums a great way to get help. It's a great place to find answers and advice! Thanks for the post.

  I understand you have questions turn on/off the device and you must press the power button several times for him to start. I'll be happy to help you.

  Please try these steps first. Perform a hard reset.

  • Steps to do:
  • Turn off the computer and unplug the charger. Then remove the battery.
  • Press and hold the power button on the unit for 15 seconds to carry out the static electrical charges inside the machine.
  • Replace the battery and the charger plug it back. Try to turn on the computer.

  If it fires up immediately the issue is resolved. Otherwise, try to turn on the computer without the battery and check that it works immediately.

  In your message, you said that it works very well with the charger. However, I need more clarity here to help you better.

  It works immediately when the adapter is connected and the power button is pushed only once?

  If you again press the power button several times, it may be a faulty power button, and you will need to contact the hotline at the service of the unit.

  Let me know what happens when you try to turn on the unit without the charger?

  Visit this link to contact support phone:

  http://HP.care/2bjG4nE

  Hope the problem is solved without hassle. Please keep me in the loop.

  Take care and have a week Holy.

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• Satellite L550-1CW does not start by pressing the power button / stop

  I have a Toshiba Satellite L550-1cw that won't start, lights up when I press the power button all the lights at the front, the fan starts and he is looking for a HARD drive for about 2 seconds and then stops.

  I tried a new HARD drive, but the same happens.
  I was told that all this must be ignored and buy a new one that is not an option.
  I love this laptop and want to run again as this is the best I have ever owned.

  Help, please

  Andrew

  Can you give us more information on this vulnerability?
  You see something on the screen after pressing the power button?
  You can access the BIOS by pressing the F2 key immediately after switching on the device?

  Despite this whole issue, I think that if nothing is visible on the screen it could be a serious problem with one of the following: RAM modules, motherboard, CPU/GPU.

  From my experience the RAM memory modules are not very expensive (2nd hand might be good enough) and the replacement isn t very delicate in the case where the faulty memory causes this problem, the laptop could be set for a little money.

  But in case of problems of motherboard, laptop repair procedure could be very expensive.

• I can't start with Satellite P10 by pressing the power button more

  I can't start my Satellite P10 by pressing the power button more.
  Sometimes, very rarely its starts when I hold the power button for a while say 10 seconds.

  I tested the power supply and a battery to my friends P10 (of the same type) and both work very well.

  So it must be a problem with the key.
  No idea what to do?

  Thanks for any help

  The best.

  Tobias

  If it s a button or a power supply electronic problem, then you can't do anything.
  In this case assistance by the technicians of laptop would be necessary.

  But the next time that you should try this option if the laptop turns on not;
  Remove the battery and unplug the AC adapter from the laptop for about 30 min.

  After this short period of time to reconnect the two parts and check if the laptop could start.

  Good luck

• Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

  It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

  I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

  If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

  Thanks for your help.

  Damicon999 wrote:

  Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

  no chime, black screen, that's all.

  I don't think they are infected.

  The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

  No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• Help - HP Pavilion a6030.uk desktop computer. Have to press the power button several times to start?

  Hello

  I have a HP desktop computer. The model is HP Pavilion a6030.uk, Opertating system: windows vista.

  My computer has had no problems at all until yesterday for some reason, I had to push the switch several times to start until he finally turned and did normal starts. As I would press the power as normal to start button, but all of a sudden, it turns off after about 2 seconds and so I would tap on the switch several times and each time it will not start and turn off, then the power button could be pressed again until it would finally turn on and start and run as normal and seems to work correctly. And it was the same thing today, I pressed the power button mutiple times (for example 6 times) until she finally started as usual.

  Savvy/computer im not very well informed or wise in this area, please someone will help me and give me some advice/help to fix/resolve this problem.

  Thank you for taking the time to read this and any help would be appreciated for this problem.

  Thank you.

  Vonbon90, welcome to the forum.

  When I see these symptoms on an old computer, I think it may be a power supply (PSU) failure/ing.  Here's a guide that will help your troubleshooting it.

  In addition, you could test the memory.  This can be done by removing all modules of memory and replacing them one at the time and start.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• A font I need is not available in italics. Corel Paint Shop Pro produces the police in italics when you press the Italic button in the software, but I don't see any way to do this in Illustrator. Help, please.

  A font I need is not available in italics. Corel Paint Shop Pro produces the police in italics when you press the Italic button in the software, but I don't see any way to do this in Illustrator. Help, please.

  Select the text and use the Warp tool to give a fake italic.

• PC does not start when you press the power button, after that starts automatically as a ghost!

  I have HP Pavilion a6030in, my pc does not start when I press the power button / stop ther, but she starts automatically after some time after that, it works fine.

  Even once when I closed and leave it for a while and still the problem is not resolved.

  Help, please

  I solved the problem

• iOS 10 - now I touch Touch ID, * and * press the Home button to open iPhone?

  I have an iPhone 6, and today I have updated to iOS 9.3.5, to 10.0.1.  One thing I noticed that really bothers me, it's unlocking the device.  With iOS 9, I had to touch the Touch ID to unlock.  Now I touch the ID to touch and sometimes it unlocks, and sometimes, I see 'Unlocked' at the top of the screen and "Press home to open" at the bottom.  I have to press the Home button to open the phone.

  It seems to me that having to push the home button more often will put more wear and tear, causing to fail more sooner than it otherwise.  Who thought it was a good idea?  It is perhaps a subtle boost to force me to update the iPhone 7, with his home in the solid state button?

  I think it's something that needs to be modified in iOS 10.0.2.  Make sure that touching just the Touch ID opens the phone each time, as iOS 9 has done.

  Happened to me too.  To repair. go to General settings accessibility HomeButton scroll Restfinger unlock... .and turn on.

• Increase in Wake - should not have to press the Home button to unlock

  Hi all

  I appreciate the work that the Apple development team did to iOS 10. Most of it's amazing as usual! BUT...

  The revival of the Wake feature needs an additional configuration option. In fact, some of us LIKE how quickly iOS 9 unlocks the phone and have the habit of hitting the power button to turn the screen to access the shortcut of the camera or using a finger not configured to press the Home button.

  That said, if I 'raises to Wake"my iPhone, having to press the Home button to complete the unlocking process is not intuitive. It must simply unlock and go to my home screen.

  As this MUST have been done intentionally, I think that you should give us the option attached to "Raise to Wake" function to enable or disable the duty press the Home button to unlock.

  Who else agrees? Thanks for your time!

  byersbw wrote:

  Who else agrees? Thanks for your time!

  Polls don't is not allowed here and probably wouldn't have much affect Apple's not read here.

  Submit your comments directly to Apple here:

  http://www.Apple.com/feedback

  Good luck.

• By pressing the home button does not take me to the home screen of iOS 9.3.3

  I have recenly updated upgraded to iOS 9.3.3 and I noticed that pressing the home button does not take me to the home screen. The only way to get there is by using the creature of multitasking. (double pressing the home button) Also, some applications seem to freeze if turn my phone off and then turn it back on, or when I access it via the multitasking function. Can someone please help?

  Try a forced reboot. Hold down the Home and Sleep/Wake buttons at the same time for about 15 seconds, until the Apple logo appears. You won't lose anything.

  If a force restart does not help, try a system restore. First save your device via iTunes. Also import your photos on your computer and copy all the important data. Reconstruction of the support first test and test. If this does not help, you may need to restore as a new and reconfigure from scratch as the backup may be damaged. It is important to have your photos and your saved data separately from the backup. Here are the steps for a restoration:

  https://support.Apple.com/en-us/HT201252