Network Assistant will not connect pc to the LAN, but connect to the internet properly

Similar Questions

• my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card

  connection network card

  my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card... I'm not sure how to solve the problem of the dat

  Hello

  Did you change your computer?

  I suggest you to follow the links and check out them.

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems

• Satellite P200 will not connect to wireless internet

  I have a Toshiba Satellite P200-143.
  I changed my internet provider, but the Toshiba will connect to the internet only when the blue ethernet cable is connected.

  Yet my laptop marry connects easily.
  I'll start, connect to identify the wireless network and tap on connect, it tries, but says connect with limited access.

  Any ideas plse.

  Hello

  (1) have you activated the WLan card?
  To activate the Wlan you must pass the antenna WLan switch on IT (LED should Flash) and you must use the FN + F8 key.

  (2) did you check the WLan configuration?
  -SID, right encryption settings, good filtering by MAC address, good TCP/IP settings on the right

  (3) have you tried to update the driver WLan?

  (4) don't you update the BIOS?

  If this is not the case, check this box!

• my computer will not connect to wireless internet

  I got a bad virus on my computer and I had somone who knew what they were doing to clear my computer.  Once they wiped it they put all the disks provided with the computer back on, but I can't conect to wireless internet. When I go to connect to a network, it is not see the same there is wirless avalible. I know the router is working because my phone can pick up the signal. I don't know what to do?

  Hello

  Turn off the router (unplug power cord), wait a few minutes and then turn it back on.
  Restart and try to sign in.

  1 do these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------

  2. your router could be suspicious here, you have successfully updated its firmware as a possible solution? And
  I would update your WiFi drivers on computers. How you are positioned in the router?
  Are there obstacles in the path?

  Actually try updating your driver and disabling the network logon. You can use a wired connection
  If possible or download drivers on another computer and transfer them via removabler
  media.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver-
  Note the version - click on update driver (can't do anything as MS is far behind certifying)
  drivers). Then right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver
  stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version.
  (Those become your fonts of rescue system manufacturer).

  Repeat for network (NIC) card and is a good time to get the other updated drivers Vista
  love the updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE like
  they are almost always old, and you can search for drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - define the network locations
  page - down left click on merge or delete network locations - REMOVE all instances of your network
  (and all the others you no longer use)-RESTART. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an address IP of certain routers or from certain non-Microsoft
  DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Updated but will not print pages from the internet

  I had AdobeX, but he refused to print anything from Firefox, not even a selection. I deleted and I went back to 9.4, but it STILL will not print for me more. How can I fix it?

  OK, I got it - it turns out that the upgrade has changed the default printer in the settingds for Firefox... I won't go back to 9 or X however, as others seem to have hurt, too.

  FIXED - FIXED - FIXED

• Games will not be installed by the internet download

  stops the installation when downloading on Internet

  Download the installer to your desktop and right-click on it, and then click Run as administrator.  It sometimes works when standard installation procedures only.

  If this does not work, please transfer your question in the Forum http://social.answers.microsoft.com/Forums/en-US/vistagaming/threads games where people who specialize in the installation of games among other will be more than happy to help you with your problem.  Please post the name and the version of the game you want to install (and a link to the download site) as well as which version of Vista you are using when you post here in order to get the best possible service.

  Good luck! Lorien - MCSA/MCSE/network + / A +.

• my mail on the computer is not my mail server need to change my e-mail address, returned in error, if I'm to some Web sites and will not send message from the internet.

  I tried to fix it but don't change things unless I know exactly what to do, need directions. The computer belongs to my son and his name appears on the files still too, I have no manual, if you know where I could get one let me know please. I'm not very good with this kind of problem on my computer. Thank you

  http://www.SimpleHelp.NET/2007/02/07/a-beginners-guide-to-setting-up-Windows-Mail/

  Link above has an easy to follow Guide to set up Windows Mail.

  Contact your ISP (Internet Service Provider).

  They offer your broad band/Dial-up connection.

  Ask them to:

  username
  password for your service account to wide band/Dial-Up with them

  Server of incoming POP3 mail
  outgoing mail SMTP server

  The above information is required to set up Windows Mail.

  ISPS are usually happy to help you set up your email account.

  See you soon.

  Mick Murphy - Microsoft partner

• HP Officejet 6500 a: printer will not connect to the wireless network.

  I got this HP printer for a while and it worked fine.  Our old router is out and we had to get a new one.  Installed perfectly and printer continued to work properly.  The password for the router was ridiculous, that's why I changed it to something much more simple to remember.  Since then, my printer will not connect to wireless internet.  I have a ~ and reinstalled the printer but still have the same problem.  I thought maybe to try the former password would, but who does not work either.

  Anyone has any ideas that might help before chuck it and go and get a new one altogether?

  Thank you.

  Easy things first.  Turn off the router and the printer.  Turn on the router and wait 3 minutes.  Turn on the printer and see if it connects to your router.  Status?

  If no joy, temporarily disable all security in the router.  Now try to connect the printer to your SSID not guaranteed without password.  Status now?

  If OK, go back and add WPA2-AES with your simple password.  Status now?

• HP 7520: HP 7520 will not connect to the wireless network

  There is some additional information to

  http://forums.Xfinity.com/T5/home-networking-router-WiFi/HP-7520-will-not-connect-to-wireless-networ...

  on this issue.

  Have several APs for a single wireless network allows the printer foolish law.  (Not a Repeater, a second AP connected to the local network with the same configuration of network for security, etc.).

  I solved this problem.  In accordance with the discussion on the link, the problem is that the printer cannot connect to a wireless network if there is greater than 1 for a wireless network (SSID) name wireless access point.

  This thread has had several useful suggestions, but what finally solved the problem, it's the second point has access to a mode where I can create a 'virtual' access point and, above all, a SSID associated.

  Note that not all access points or routers support virtual APs, but this function seems to be more common over time.  Older models is not able to do that.  However, a new access point is sometimes cheaper than a new printer.

  If you do not understand the jargon in the procedure below, I recommend that you find someone who does, then they can do it for you.

  Solution:

  1. On one of the wireless access on the network, create an a new virtual AP with a slightly different name SSID (for example < name of the network - > _1), on the same VLAN (usually VLAN 1).  You may need to put the AP in "multiple AP mode" or something similar, and then restart the AP.  All other settings (DHCP, security, mixed mode b/g/n, etc.) must be the same for the new SSID.
  2. Run the printer Wireless Setup and connect it to this new SSID
  3. Confirm that the printer can be seen by other devices on the network

  Tips:

  • Check the security is the same as the original SSID, Alternatively you can create a vector of insecurity in your network.  Do not WEP-128 when the other SSID uses WPA2 AES, for example.
  • The AP I had had several resets to make it work because of the mode and parameter changes.
  • If you connect the SSID but cannot connect to or be seen by anything on your network, check the new SSID/AP is in the same VLAN as the original.
  • Because the printer is not roaming, and the speed is not a problem for me, I used the access point that could support this solution, which is deeper and slower than my primary AP.  I have not noticed any problems.

  The printer has been reliable on the wireless now on the new SSID, 48 hours.

  I have not upgraded any software on a client of the printer (PC, Mac, phones).

  I think that it is a positive confirmation that the problem is with the implementation of the printer of the stack of network and not with the driver or client software on remote devices.  The 802.11 protocols provide for a network name (SSID) wireless with several access points using different MAC addresses.  I suggest this HP look into this as a potential bug with their network printer for the 7520 protocols stack.

• WIFI on my C850 Satellite can detect the network but will not connect

  I just bought a satellite C850 - PSKCCA-02D00M

  The connection to the LAN works fine however the Realtek RTL8723AE without wireless/Bluetooth will not connect to the network. It can can detect them just does not connect. I used the troubleshooting, and he cannot sort.

  All other devices connect very well as Iphones and Kindle

  In the config is doctor says that the adapter is enabled in a domain and in the adapter another status is down.

  I took back to the initial power and installing and unistalling and reinstalling the adapter using the driver on the website.

  Any help is welcome. I don't want to have to take back just for this issue

  See you soon

  Your WLAN is locked? Can you connect WIFI if you delete the WIFI password for two minutes?
  Have you tried to reboot your router?

• Laptop will not connect to the wireless network

  I have a Toshiba laptop with windows Vista, and it does not connect to wireless internet at my father's House. My father and my sister have the same exact computer, and both of their computers work perfectly well. Mine will work with an ethernet cable plugged in, but when I try to connect wirelessly, it does not work. I've never had this problem in my mom's house or anywhere else. Can someone help me please?

  Hello

  This is a security feature of each wireless router I've ever seen, although I wouldn't be surprised to discover that some router didn't do it. You need to check your router admin pages to see if mac address filtering is in effect. Address filtering Mac prohibits access to the router by any unauthorized network device. All network devices have a unique mac address which you can find through opening a command prompt (click Start, then type cmd and press enter) and then typing ipconfig/all. The output refers to your device Wireless 'physical address' (mac address) and will be in the format hh-hh-hh-hh-hh-hh, where hh is a hexadecimal number (A - F and numbers 0-9), dashes are not important and may not be required when you enter your mac address in the router configuration.

  Tricky

• Windows Vista detects the wireless network but will not connect to it. Two other users in the same office connect without difficulty.

  The title says it all really.

  I was connected and working normally for about an hour this morning, until suddenly the connection has been lost.
  Windows detects the wireless network but will not connect. Two other users in the same office connect without difficulty.
  Help, please.
  Thank you.
  original title: vista detection network but will not connect

  Hi JulianBeach,

  1. you have made no changes to the computer before the broadcast took place?
  2. What is the exact error message you get?
  3 is connected to the domain of the computer?
  4. what happens when you try to connect to the network?

  Try the steps from the following link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Wireless network card: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

• My Ipad mini will not connect with my wifi at home.  Other devices are able to connect with wifi.  I repeatedly entered the wifi password, but this is not ACCEP it.  Worked very well.  I turned the mini ipad market and nothing.  Help!

  My Ipad mini will not connect with my wifi at home.  Other devices are connecting with the wifi at home.  I turned the mini ipad market a few times and nothing. He recognizes wifi but when I touch the password, it continues to request the password.  Help!  It was working fine earlier in the day.

  What has happened with your iPad since earlier today, when it worked? updated App or iOS? nothing at all

  If your iPhone, iPad or iPod touch connects to a Wi - Fi - Apple Support network

• My iPod touch will not connect to WiFi and I followed the steps posted. Also, when he dies he thinks that it is December 31, 1969. What can I do to fix this?

  My iPod touch will not connect to WiFi and I followed the steps posted. Also, when he dies he thinks that it is December 31, 1969. What can I do to fix this?

  Not knowing what the 'followed the steps posted' have been

  The iOS device connects to other networks? If Yes, which tends to indicate a problem with your network.

  The iOS device sees the network?

  Error messages?

  Other devices connect now?

  The iOS device has connected before?

  Try the following to rule out a software problem:

  -Reset the device iOS. Nothing will be lost

  Device iOS Reset: Hold down the On / Off button and the Home button at the same time for to

  ten seconds, until the Apple logo appears.

  -Power off, then back on your router

  . - Reset network settings: settings > general > reset > reset network settings

  - iOS: troubleshooting connections and Wi - Fi networks

  If your iPhone, iPad or iPod touch connects to a Wi - Fi network

  - iOS: recommended for WiFi routers and access points

  -Restore from backup. See:

  iOS: how to save

  -Restore factory settings/new iOS device.

  If still problem and it does not connect to any networks make an appointment at an Apple store Genius Bar because it appears that you have a hardware problem.

  Shop Apple Store - Genius Bar

• HP b209a printer range will not connect to router comcast using the WPS button

  HP b209a printer range will not connect to router comcast using the WPS button. I try to use a new Comcast router (technicolor TC8305C). When I try to connect the printer times out and says that no connections are when I check for wireless connections. Yet, when I print the network configuration page, the SSID for the new router is at the top of the list. I reinstalled the software by the support of Comcast, but it did not help.  I'm ideas please help!

  Thank you

  Never use WPS to connect.  If done it should be disabled in the router for security reasons.  Connect manually via the SSID and password following the instructions in the manual.