network computer detects and installs but won't print on shared printer

Similar Questions

• I have problems to re - install Acrobat 10 on my new mac pro. It downloads and installs but I can't find anywhere on my computer.

  I'm having problemsI'm having problems reinstalling Acrobat 10 on my new mac pro. It downloads and installs but I can't find anywhere on my computer. Re-install Acrobat 10 on my new mac pro. It downloads and installs but I can't find anywhere on my computer.

  You can install the Acrobat x update without installing acrobat 9.

  Start the software acrobat x installation.  you will be prompted for the serial number x' are, first of all.

  After entering the serial number x' are, you will be asked (with a drop-down menu) to select the eligible program (acrobat 9).  Select acrobat 9 and enter the serial number its (acrobat 9).

  Enter the correct number at the right time and proceed with the installation.

  Make sure you did more that 'try the link.  Make sure you have made the necessary changes or explain if you couldn't tick the box "any developer".

• print jobs in the queue from the computer to the top, but do not print

  1400 series all-in-one print jobs in the queue from the computer to the top, but do not print. Scan and copy functions are fine. What is the problem?

  chrismcgo wrote:

  I've upgraded to a new computer with windows 7 a month ago. The printer worked fine until last week. I tried the remedy proposed to other Hp users, but the computer will not accept the software provided with the printer, so the printer is always offline. Any other suggestions?

  I suggest the following: disconnect the cable USB, then download the full driver recommended from HP here.  Once the download is complete, run the Setup program.  Do not connect the USB cable until the installation program invites you to do.

• network is detected for c7280, but print jobs are sitting in the queue and will not be printed

  The first time in the forum because C7280 is no longer supported. Lasted forever except that updates always seem to bumble. Last update caused printing to sit in the queue instead of actually printing.

  The network is detected thanks to a response I've read similar problem, someone else had. I disconnnected cord power, then pressed on # and 6 at the same time. Network connection is returned after this reset. Thank you for this!  But now this second question described in the first paragraph.  We believe that it is a software problem in the updates.  Any suggestions?  Thank you!

  Ok! Error of the operator on my part! Upon reflection, I realized that the rest of the House is on wifi, our main computer is NOT. Before our disassemble everything, we had the HP hired cable! So, everything is back to normal. Thank you very much for your kind attention. We have still benefited from the previusly information obtained when wifi was not recognized at all, so all is well in the household and everyone is happy now!

• ESXI 5.0 installs but won't start

  I bought a test computer to try to esxi and run some windows xp vm, the motherboard is Intel and Corsair SSD hard drive (pc is new), I performed the installation and it reported no network card which was an Intel onboard, so I bought a Sunix card and installation continued without error, but when I restart the machine It's as if there is no boot sector or operating system installed on the drive and it does not start.

  Have you changed the type of controller in the BIOS? When you use an SSD you to change AHCI SATA controller (or other). You also need to enable virtualization technology. Check the manufacturer's guide to activate that...

• Update of security for Vista KB2676562 says it successfully updates and installs but does not work.

  It won't install the update when I start the computer again. It always shows that it is available for download.

  I tried Microsoft Security to address them, but said he had no problem.  Is it my computer problem and is not a problem of update?

  Thanks in advance.

  Hello

  1. you get any error message when you try to install updates?

  2 are you able to install some other updates?

  3. what version of service pack is installed on your computer?

  I suggest you to follow the steps below and check if it helps.

  Method 1: Try to reset the Windows update components and check to see if the same problem happens: http://support.microsoft.com/kb/971058

  Method 2 :

  Try to put your computer in a clean boot state, and then try to install the updates.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

   

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

   

  Method 3: If the problem persists then try to install the updates manually from the link below.

  Update for Windows Vista (KB2676562) security: http://www.microsoft.com/en-us/download/details.aspx?id=29829

  Hope this information is useful.

• Mysterious problem - HP DL380 G7 Server - ESXi installs but won't start

  Someone has already seen this? I have a new DL380 G7 server, I have 8 drives and installation with 2 bays, RAID10 (4 discs). ESXi 4 DVD comes from an ISO, I downloaded from HP (and have used on other servers as DL380 G6 without problem). The installation goes by at the end asks me to restart, and then I remove the DVD and restart. The controller, SmartArray P410 is defined as the boot device (there is one in the system) and I even try the F11 at startup and tell it to boot from HD... the screen is blank for a second then the server tries the other boot devices (network, etc.).

  I am really puzzled. During installation, the installer sees the two logical drives very well. I took LogicalDrive0 to install to.

  Thoughts? I'm puzzled.

  I agree with the suggestion of J1mbo . It is a good way to make sure that you install the operating system/ESXi on the expected logical volume.

  Another possible way to make sure that you install on the logical volume is created volumes with slightly different sizes. (I usually create one with only 10 GB for ESXi). In this way, you will be able to take the logic unit number in the Setup program based on its size.

  André

• OfficeJet 6700 installs but does not print

  We have an Officejet 6700 on our wireless network. My computer can find and add the printer (using the latest drivers, I downloaded).  Once installed, it seems to print but nothing never goes out on the printer.

  It is most likely a network issue, but maybe anyone know the magic that I need.  The wireless is on a different subnet (192.168.40.X) wired computers (192.168.10.X, running Windows 7).  I checked all the settings of the firewall, and it is configured to allow traffic from 10.x to 40 x and vice versa.  To install the printer, I 'Add a local printer' and then create a new standard TCP/IP port and use wireless IP of the printer - the printer is certainly connected to the network and I used the information from the printer Panel to get the IP address.

  The installation process continues, with the driver that I just downloaded on the HP site, and voila, the printer appears in my printer/fax devices!  He asks you about printing a test page, I say Yes... and nothing ever happens.  Even with apps like Word or notepad, I select the 6700 and print and I get no error, but nothing is printed.

  Any ideas? Thank you.

  (Note: the firewall * is * configured to not allow wireless devices to see each other, so I can't try the printer on other computers connected to the sous-reseau.40.x.)

  I understand that you can test the printer communication seems applicable.  When you click the printer icon on your desktop, what do you see?  It does not open the HP printer Assistant or is it the configuration page to connect to the printer? You have even an icon?  If no icon, click on this link to install the 6700 (Windows 7 64-bit U.S.) Officejet full feature software and drivers .  I know you said you did already, but I wanted to give the link to the case where.

  This printer has a new firmware update to help with wireless facilities. Version: MPM3CN1316AR (link is for Windows 7 64-bit US).

  Disable all firewall (see gurus network on deactivation of all the antivirus software and firewall temporarily). Since you have the generic driver in your printers and devices folder, select all programs > HP > Officejet 6700 > installation printer, software and try to reinstall the network printer and let me know what is happening as well.  You get a successful installation and a registration page?

  I will gladly help you get the installed printer.  I will work with you as the network guys know well your installation.  Looks like the firewall blocks.  Here is a link on how Firewall interferes with network installation.  I hope this helps!

• Configuring the network for windows7 and computers portable XP with printer connected to the router

  Computer laptop windows 7 works with the printer lexmark that is connected to the router, but the laptop XP who worked with the printer can't find using the "add a Printer Wizard. Two portable computers connect to the internet O K

  Printers configured in this mode are better develop a fixed TCP/IP address.  Your printer manual should tell you how to do this.  In general, there is a 'Settings' menu on the printer where it can be defined.  The IP address should usually have the first three digits than other devices on the subnet (for home networks it would be something like 192.168.1.x) and the final number should be unique and apart from the DHCP numbers range that your router would normally assign (see the manual of your router).

  HTH,
  JW

• Printer shows ready and connected but does not print how to reconnect it

  Printer HP Photosmart 5520 is not yet shown under devices and printers, but when I do caillet shows Photosmart 5520 connected and ready, but it will not be printed.  Only, it started when I had another problem with emails and respond and called century link (my emailer) on another problem.  Can someone tell me what to do, I have the disc and have inserted and nothing going on help please, I really need the printer.

  Ron,

  Thank you for your answer and I did something that apparently worked.  Before your apply I shut down the computer and the next time I opened it, the printer worked.  I think there were some documents before and when I turned it on again, it worked.  Thanks for your reply, I did apparently accidentally.

• CS5.5 Master Collection downloads and installs but cannot find on my computer.

  Hello, I have a fairly new HP desktop computer running Windows 10.  I downloaded the Windows version of the software here: Download Adobe Creative Suite 5.5 products and used the installation program, but when I'm ready to activate with my serial number adobe, a message appears saying Master Collection is not on my computer. I restarted my computer, delete the software, restarted and re downloaded the software.  Has anyone else encountered this problem?

  An idea that MAY work to install or run some programs in Windows 10 old... works for some, not for others

  -http://www.tenforums.com/tutorials/15523-compatibility-mode-settings-apps-change-windows-1 0 - a.html

  - or run as Administrator http://forums.adobe.com/thread/969395 to assign FULL permissions can help... said yet, but sometimes it is necessary for all Adobe programs (this is same as using an administrator account)

• Install security updates "successfully", but then my computer downloads and installs the same updates again

  Original title: at Microsoft course to resolve this ONGOING problem, & VERY BORING PROBLEM with his Windows security updates?

  Morning everyone,

  There was considerable number of complaints about the failure of Microsoft to solve the problem with its updates of Windows, including updates security for XP, Office 2003, the removal tool malicious and the infamous KB2538242!  I saw these varied complaints not just here, but on some other sites as well forum.

  In the evening of Tuesday, July 12, 2011, I once more has received notification of Update icon in my taskbar and clicked on it to start the updates.  According to the list, there were 5 so-called updates downloaded & installed... as shown below: (my auto-mises update is updated every day at 01:00):

  KB2555917 (a security update for XP)

  KB2538242

  KB2493523 (a security update for Office 2003)

  KB890830 (updated Windows Malicious Software Removal Tool)

  KB2507938 (a security update for XP)

  SUPPOSEDLY... .these updates have been installed.  But, just as happened previously, Microsoft Update icon still reappears in my taskbar within 20 minutes the so-called updates being completed!  Yet once, I went through this cycle of "download & installation" these supposed updates 4 different times before visiting the account that Microsoft has NOT YET SOLVED THIS CURRENT QUESTION! There is absolutely NO help is available, whether of Microsoft at all... except if you're loaded with money to spend on paying them to offer some apology for the problem.  Here ARE the UPDATES security AND in accordance with the PROTOCOLS of MICROSOFT, MICROSOFT IS supposed TO BE PROVIDING SUPPORT FOR THE QUESTIONS OF THIS TYPE! 

  When the problem instead of turning its back on its customers with the blade go Microsoft to wake up and solve this problem continues is to excuse this "oh, there is no support available for these security update issues... unless you are willing to PAY SOME COSTS FOR the SERVICE?  (It was the response I got from one of the support staff for the customer to Microsoft by phone, said by the way!)

  You VERY DEFINITELY have an ongoing responsibility to your Microsoft customers.   What you do to solve this maddening, growing problem, and how a Win XP SP3 client can get any help?

  Welcome & thank you for your comments.

  Please keep us informed of any progress you make, Pete.

• USB stick detected and works but not displayed in the computer

  I am running windows 7 Professional. Any drive USB storage that I connect to my laptop is not in the computer. He is awarded a legitimate drive letter and I can access content drive by typing in the drive letter in the bar of navigation or term. I checked using the disk management utility. Operations on the work of perfectly good files. The only issue here is that the reader does not appear or is hidden in the computer. I put the folder options to display everything, IE. no possibility to hide whatever it is has been disabled. In addition, when you click the remove safely icon in the status bar, the device is listed as «...» "instead of real name and the ring road. Note that there is a user account that is my administrator account.

  Interestingly, I have created a new standard user account and was able to see the USB into the computer when it is connected to this account. Is there any setting I can change on my admin account to enable this? I would prefer not to have to create a new account and reconfigure all my settings.

  Hi VJ17,

  It could be that your user account has been altered.  See the following article:

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  Hope this helps

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Computer formatting and installation of El Capitan

  Hello everyone.
  Because I had to finish my thesis, I was forced to create a Linux partition on my Mac, with the addition of a bootstrapper.

  Given that I experienced a few problems to update my version of MacOs (sometimes bootloader not was not loaded when the computer was on and automatically started MacOs), I stopped to update software to version 10.10.1 (Yosemite).
  Now that my thesis is completed, I would like to completely format my computer, removing Linux partition and restore the entire disk with MacOs. At the same time, I want to update the operating system to the latest version of El Capitan.
  What is the procedure to get it all?

  Thanks for the support.

  I suggest you to download setup OS X El Capitan, put it in a flash drive, make a backup of your files and use the flash drive to format the drive and install OS X El Capitan.

  1. Open the Mac App Store and download OS X El Capitan. The installation program displays upward when the download is complete, so shut up.
  2. Download DiskMaker X and use it to create a bootable USB key with the installation program. You need at least a 8 GB flash drive.
  3. If you have not already done it, make a backup of your files on an external drive with Time Machine-> use Time Machine to back up or restore your Mac - Apple Support
  4. Hold down the ALT key during start up your Mac to the top, choose your USB drive as boot drive and wait while the installer for OS X El Capitan interface load upward.
  5. Open utility disk, choose your internal drive at the top of the sidebar and format him. Don't forget to format the new partition with "OS X Extended (journaled)" as the format.
  6. Close the disk utility and reinstall OS X.
  7. At start-up, OS X will ask you to restore a backup, if you have a. Connect the external drive with the backup, and then follow the steps. It will allow you to restore only the files you choose.

• Help me REMOVE the duplicate folders My Documents and others created automatically when I install Virtual PC in XP Mode to run older programs. I removed the computer virtual and XP, but it does not remove the My Documents folders duplicate.

  While trying to run some older programs (Corel) in characteristic as advertised XP mode from my new Dell laptop and Windows 7 PC, I created Virtual PC and XP mode Setup.  Somewhere during this process, the system created in double My Documents, my pictures, my videos, files etc. that you can not (no authorization) access through Windows 7.  I understand that they may is accessible while you were in Virtual PC.   I came to my senses after the poor performance of Windows XP/Virtual PC and decided to remove remove these programs (and buy Corel for Win7).  I followed the instructions for a good dismantling of Microsoft who think in the end, these inaccessible files would disappear and I would have a struture of own file again.  However, duplicate inaccessible folders still remain and I can't get rid of them.  Believe me - it's a pain because it's very confusing when you browse folders.   There is no files in these folders, so there is nothing that we need to go.

  Please, for the love of peace in my family, tell me how I can get the PC back where it was when we first install Windows 7.   And - what's the problem of not having a complete control of my pc?  Personally, I'm offended that Microsoft has locked the users so that they cannot use their own brain - apparently I'm not the only one...  If you are willing to share, I would appreciate a detailed response.

  Hello, SuperMomNot

  Where are these records?

  Virtual PC will create only shortcuts to installed applications in XP mode, no records. The ability to open and save files that are stored on the host computer is made via the network sharing of files between the two.

  David
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.