New arrivals

Similar Questions

• First issue of new arrivals

  Hi everyone, I'm running a PSC1510, he had some time.  Was a good printer until yesterday.

  A lack of color ink.  Replacement cartridge.  A ran the registration and test sheet.  No yellow no printed on the test sheet.  Ran the ink loading and cleaning according to the instructions in the manual of head.  Same result.  Photo printed with lots of brown/beige/yellow inside.  None of these printed cloours.  Change cartridge suspecting the faulty cartridge.  HP cartridges incidentally.  Same result without yellow.  Inspected cartridges can see no damages.  All open intact when packages.  Cartridges from different sources.

  Having exhausted every step of the manual.  Photos write legibly but just shades of red and blue.

  Any ideas?

  Gari

  Thanks Bob, I tried the hot water thing but it didn't work so I tried a new cartridge, (I had a right for the Exchange I bought yesterday) and it worked.  It seems so strange that two new cartridges show the same faul, t if I got one of them for a while.  In the future, I'll buy them as needed instead of keeping spare parts.

  Thanks again

  Gari

• Slow response from phone to monitor data recovery

  hhaving problems with my app Apple Watch (watch OS 2.2) of the iPhone data recovery 6 (iOS 9.3.4). When I click on various watch apps - FaceBook Messenger, Messages, etc., they seem to take forever to recover data. I tried to restart watch it and iPhone without any improvement.

  If I remove the applications from the watch and then reinstall them this solves the problem for a short time.

  Ahy suggestions?

  Hello

  For best performance of your devices, make sure that both Bluetooth and Wi - Fi are enabled on your iPhone (and keep them permanently active).

  Also, make sure that you have installed the latest versions of all applications (on your iPhone: App Store > updates). To install updates for the associated Apple Watch applications also automatically, select automatic App install (on your iPhone, in the application of the watch, go to: Watch My > General > App Install).

  It can help to disable the twinning and re - pair your watch. The app shows on your iPhone takes a backup of your watch automatically when the disparity with the app choose to restore from backup during the whole upward. Most of the data and settings will be restored, with a few exceptions (for example cards Pay Apple, access code):

  • Cancel the twinning of your iPhone - Apple and Apple Watch Support
  • Set up your Apple Watch - Apple Support

  In the future, notes that new arrivals under watch OS 3 - software update that is should be out this fall / Fall - include much faster loading of your favorite applications, including applications to launch immediate up-to-date information.

  More information:

  http://www.Apple.com/Watchos-preview/

• Distorted crackling sound when you use either 32/64 bit Windows 7 on Fujitsu Siemens Esprimo V5535 using high definition Audio Device.

  Hello. I have a problem with the sound on my computer. I think that's maybe a bug in Windows 7. Whenever I try to play music or watch a video there is some distorted crackling sounds that come also with audio. I had no such problem in XP or Vista. I have tried everything to solve this problem re-installing the audio drivers switching different and trying different versions of Windows 7 but without success. I have not had any problems with him using Windows 7 beta, but I do now running version 7600. And my lapyop is well capable to run Windows 7 at 2.26 Ghz CPU, 2 GB Ram, 320 MB graphics card - its very fast. Only problem is her. I even tried the Realtek audio drivers for it and I get the same problem - and they are the most recent up-to-date.
  Help, please!
  Thank you

  Hello. I do have the problem fixed - this is if you have a RealTek sound card. You need to contact them about the problem and they should give you a diagnostic tool. Run the tool and the info. Then send it to RealTek. I got good service from them that everything was done in half an hour! They sent me a version updated their driver who was in phase beta but the change Turn Off Mode jumper (if it makes no sense to me) and it works completely fine! I even had new arrivals with him too - special enhancments that can change the height of the audio, karaoke, effects on the environment and Equalizer mode. No crackling or distorted sound.

• Insert in ListView

  Hello

  I'm developing an application of news rss in listview mode. I intend to insert the element of publicity to the listview for every five new arrivals like this:

  News 1

  News 2

  ...

  News 5

  to advertise

  News 6

  News 7

  ...

  News 10

  to advertise

  ...

  I don't know how to get the current index of component list dynamically. Any suggestion? Thank you.

  Hello

  It's ListItem.indexPath.

  But you might want to create a ListItemComponent with different types of ads, for example:

  ListItemComponent {
    type: "advertisement"
  

  and implement itemType function in ListView to return the 'advertising' for appropriate indexPaths.

  Please see this page for details and code examples:

  http://developer.BlackBerry.com/native/reference/Cascades/bb__cascades__listview.html?f=ListView

• sales of the app

  Hello

  I had my first PlayBook app approved a week ago, and I would like to ask:

  -Is it normal to get 'high' sales on the first two days, then very little?, I had a bad review which I have already asked to deny, don't know if this is affect sales...

  -Most of the purchases are Canadians, some of the United Kingdom and others, but none of the United States?, this normal?, coming from the world of iOS, this is just the opposite.

  -Advice on how to promote a game app PlayBook?, I'm surprised there is no way to :-(coupon codes

  Thank you!

  1. Yes. It's normal. You were under the new arrivals so that you noticed it. And the bad reviews may decrease the number of purchases. But soon, they will be denied. We'll wait and see.

  2. Yes. Canadians are #1. With regard to U.S.: Yes, it's weird.

  3. can't answer you. Promo codes may be a next feature in App World.

• Release date

  I am curious to know, once an application approved by RIM what date should I use to determine the applications on the NEW ARRIVALS section? Should I use the date that you click on the button to POST FOR SALE, or the date of that approval by RIM.

  I was wondering because, lets say my application is approved on Wednesday, but I do not go home until the following Monday and press message to sell. The app would remain off newcomers because the approval date was a few days ago, or would he appear Monday when I press the post to sell.

  Thank you

  He will appear in the new arrivals to be published for the first time. It is independent of the approval date. Note that this "first time" means that if you post it, even for a few minutes, then remove from the sale and repost later, you don't appear here once again.

  In addition, if you are new to the provider portal, note that the limitations in the App World mean that even when you publish it, it will take up to about 24 hours to appear on any given server (there are several) or a device, so do not assume that simply because that some people do not immediately that something was wrong.

• Native? Or Cascades?

  Hello

  I am porting my apps playbook on to bb10.

  They were built in the AIR, but I want to add some new arrivals whose AIR is just too slow for. I had the intention to rebuild native, but im confused, what is the difference between the native approach and the cascades.

  Which should I use?

  Okay, to be clear - Cascades * is * native. You just start using elements of graphical interface provided by waterfalls (add a few new libraries) and changes the structure of your app (using different event-handling logic etc.). But all that is available for native is available for app stunts. You don't need stunts if your app for example uses its own photos/text rendering, menus, buttons etc in place Let's say using OpenGL.

  You can probably define "Native" in your own words? What thing confuses you here?

• Script to install HostAgent UnixAgent IC

  All,

  We are moving from legacy for the new arrivals to our environments of. If I update the Linux_System to the UnixAgent agent. We are in this case using local fglams for several reasons.

  I am able to deploy the cartridge and create the agent but how to fill the FSA to monitor the host under the credentials of the fglam running on the spot as you can from the wizard?

  Cartridge #Deploys IC

  /NFS/UTL/Foglight/install/client/fglcmd.sh - srv myfms.corp.dev - usr - pwd foglight cmd - foglight agent: deploy - host - IDPack myserver.corp.dev "Host.*" - regex

  #Deploy UnixAgent

  /NFS/UTL/Foglight/install/client/fglcmd.sh - srv myfms.corp.dev - usr - pwd foglight cmd - foglight agent: create - host myserver.stubcorp.dev - type UnixAgent-appoint--nowait

  Hello, DPW,.

  We have a few exmaples with simple transfer in the files and return to. Unfortunately without XML entry as far as I know.

  Just search for ASP. This should at least give you a few examples.

  Here are a few good examples:

  http://en.community.Dell.com/TechCenter/performance-monitoring/Foglight-administrators/f/4788/t/19554329

  http://en.community.Dell.com/TechCenter/performance-monitoring/Foglight-administrators/w/Admins-wiki/5694.using-the-configservice-API-to-Setup-agent-properties-ASPs

  http://en.community.Dell.com/TechCenter/performance-monitoring/Foglight-administrators/f/4788/t/19554963

  Kind regards

  Jan

  PS. For more information, please contact Quest on PSO

• C2960-lanbasek9 - tar.150 - 2.SE2.tar high memory consumption

  Hi all

  I would strongly appreciate that someone could explain to me why my Clients-LAN Switches (c2960) during the upgrade to new IOS namely

  rump C2960-lanbasek9 - tar.150 - 2.SE1 and c2960-lanbasek9 - tar.150 - 2.SE2 upward memory consumption to somewhere between 80% and 90%.

  Is there a "bug" always with these IOS versions that could have caused this? I've never had this problem with the old version (c2960-lanbasek9 - tar.150 - 2.SE) of IOS. I've read through the Cisco Documents on these releases but wasn't too sure if new arrivals on these IOSs caused this high memory usage.

  Shown is an example of one of many c2960-switches using these IOSs. In the meantime, I intend to downgrade to c2960-lanbasek9 - tar.150 - 2.SE.

  Looking forward to your answers.

  Kind regards

  James

  

  Hello

  CSCtw83946 Details of bug

  Problems of low memory on the 2960 switches

  Symptom: Use of the high memory on the switch 2960. Without any configuration just a switch box output shows little memory. The available memory is only 5 mb. Conditionsof : No configuration to the output of the switch to the box with 12.2 (58) SE2 image. -See the compilation of statistics of memory- The Total head (b) Used (b) Free (b) Lowest (b) Largest (b) Processor 21586420 16308768 5277652 4527884 5165508 27A7D6C E/S 2 00000 4194304 2464344 1729960 1729960 1718664 1 has 00000 pilot you 1048576 44 1048532 1048532 1048532Workaround: None.This is a physical limitation and this is how far we can go. We should always be able to make configurations, although a large may need an upgrade according to C-comments

  Kind regards
  Alex.
  Please evaluate the useful messages.

• The submitted user Web App point release Date

  Hi guys. I'm kinda a beginner so excuse me if this seems a simple question.

  I dragged the forum and cannot find an answer to this.

  I created a Web application for the new arrivals and created the user input form in the secure area.

  I can't find a way to allow users to set the release date of the news item which, in many cases, not be the date of their entry into the information but at some point in the future.

  It doesn't seem to be a way to add the release Date for the user input form,

  Thanks in advance for your help.

  Hi Silverfox01,

  There are a handful of items that can not be updated from the entrance of the Web App / modify forms. Release date and weighing are two examples.

  There have been several requests for that lately, then you are not alone in your quest! - And expectations.

  Still no solution has yet been taken available. Please lets you create a support in British Colombia ticket so that they can get an idea of are weight and release date are to front-end web app entry/change of important forms.

  Hope that this 'help '.

• Compatibility memory

  I have a dell xps 8700 (end 2013) with 8 GB of memory and I want to double to 16gigs and I wonder if the memory that I choose to purchase would work with the existing ram is one I chose Savage of Kingston HyperX 8 GB Kit (2 x 4 GB) 2133 MHz DDR3 Non - ECC DIMM XMP HyperX Savage (HX321C11SRK2/8) CL11, if it is does not work with the existing memory can I replace it with this one

  Do not know this specific RAM, but many people here by her to Crucial.com for Dell computers. If Crucial recommend for a specific system, they ensure that market or they take it back.

  The fastest RAM Crucial shows for the 8700 XPS is 1866 MHz. This does not mean 2133 MHz don't work (depends on the BIOS and chipset limitations), but if you mix different speeds of RAM, it will operate at the speed of the slowest RAM installed. So if you now have 1600 MHz RAM, new arrivals can also run at 1600 MHz if you mix again to the former.

  You can also search these forums to see if other users have installed this RAM Kingston in the XPS 8700.

• 6.2 - get rid of the eternal "Virtual SAN disk scale" cluster warning

  Hello

  6.2 has a very beautiful, and and at the same time, very annoying feature. It searches the imbalances between the nodes and disks. Yeeeh no RVC more to know such things.

  Unfortunately, there is an alert that accompanies it (three in fact, see screenshot).

  I have about 55% of available space on the vsanDatastore. Who is comfortable. However, there is almost always an imbalance somewhere. I can do a re - balance and it will sort out most of the time. I say most of the time, because he refuses sometimes resolve very small imbalances. I understand that I don't like about "5% on some discs somewhere" or the other.

  However, due to having "certain imbalance somewhere" most of the time, the cluster appears with a yellow exclamation mark almost all the time. I can delete it but of course, an hour later, during the next Checkup, he pops up again.

  How can I get rid of this bloody warning. It's pretty boring.

  Honestly, there are moments where I want to downgrade to 6.1. Then things were quiet. Sometimes the new arrivals seem to have not gotten a lot of "thinking through"...

  Thanks in advance,

  Steve

  Thanks for the comments of Steve. I reported this to the team of engineers and I will ask them to look for it and see how we can solve this problem for you.

• Link portal to the HCM Dashboard

  Does anyone know how to put in place a CREF portal to link to a dashboard (for example the Dashboard Manager) HCM?  Documentation I've found is based on the use of unified Navigation which we have not activated.

  Without unified nav, then clone you the dashboard. Cloning, it means that create you a CREF just like her, but in the portal. Clone the CREF so pagelet. In the register of Portal Portal (Interaction Hub), for each pagelet, set the name of the NŒUD to HRMS.

  You can insert these ARB in project in HRMS and then copy the Interaction Hub project. If you take this approach, also copy the parent folders. For the home page tab, copy the folder of tabs. To the pagelets, copy the parent folder and the folder Pagelets. When you perform a comparison and a report, these elements will be displayed as no change. Copy them anyway. What this will do, it is updated the cache of Portal register so your new articles will appear. If you choose not to copy these elements, then you have two options:

  1. empty the cache server app and the web

  2 open the folder parent ARB in portal (after copying) and change the description. This also update the cache and load the new arrivals for children.

• Creative cloud does not, lost Photoshop, loss of work

  Apple iMac 10.9.5

  Two days trying everything that I could find on the internet for this problem without success. Was cat Friday until that connection has been lost. Cannot get on today.

  CC does not start. The icon shows in the menu bar to a fraction of a second and then disappears. I think I've tried all the solutions published in these discussions as well as anything else that I could find online. I have now lost Photoshop as well, it has disappeared from my computer. Should occur when you browse all the file deletion process. I am in the middle of a big job and dead in the water, will probably miss my deadline. Have tried to get a live chat for hours. What a mess and I see I'm not the only one. Like I'm ever creative cloud road.

  Success!

  Hope this helps someone in the same situation. (It's a Mac, OS 10.9.5)

  That's what I did.

  • Start the computer in safe MODE, Creative Cloud Desktop (CCD) has begun.
  • Restarted in normal user mode. CCD has not started.
  • Removed all items opening system preferences > users and groups (I think that this step could be skipped and only tried if the following does not work).
  • Navigate to the library folder. Rename the LaunchAgents to LaunchAgents_old folder and launch the demons folder to launch Daemons_old
  • Create new folders called LaunchAgents and launch the demons.
  • Move all the items not containing NOT the name Adobe of the 'old' files and put them in their respective folders again.
  • Go to ~/Library and do the same thing with the LaunchAgents folder.
  • Restart the computer and see if the CCD will open. Mine DID!
  • Use the creative cloud uninstall, uninstall. Then reinstall the CCD. (This should put new arrivals records LaunchAgent).
  • Restart the computer and see if the CCD works. Mine did, and I seem to be good to go.

  I do not know what files in the LaunchAgents folders were the culprits, but everything seems to work well. I wish you I did it three days ago and saved me a lot of grief. Adobe should add to their list of things to try.