New Dell computer; Microsoft does not load my thumb drive/desire connect us 2 computers for the transfer

Similar Questions

• How can I load eLearning Suite 2.5 on my new computer that does not have a hard drive?

  How can I load eLearning Suite 2.5 that I bought a year ago on my new computer that does not have a hard drive?

  If you follow the 7 steps (list here, http://prodesigntools.com/adobe-cs6-direct-download-links.html) you can dl a free trial here: http://prodesigntools.com/adobe-captivate-5-and-elearning-suite-2-now-shipping.html/commen t-page 1

  and activate it with your serial number.

  If you have a problem dl'g, you don't follow all 7 steps.  the most common mistake is not meticulously follow the steps 1, 2, and/or 3 (which adds a cookie to your system, allowing you to download the correct version of the adobe.com site).

• On the computer, it does not load XP but goes to the XP start and says: NVRD32.sys file not found

  On start-up the computer, it does not load XP but goes to starting XP, and says NVRD32.sys file not found. I have to go up to xp home line manually and it load. How to fix the problem, so he starts xp automatically without entering start xp
  Thank you

  Posing for the PC model, you show that you do not know the answer, it was a software problem, but you're right, it's a Dell.
  In any case, I found the answer elsewhere, must with the boot.ini file on XP

• When I try to start my computer, it does not load anything. The backlog, but the rest of it runs bad and slow. I can't open any programs that either, and my pointer always told it to load.

  Original title: Please HELP

  When I try to start my computer, it does not load anything. The backlog, but the rest of it runs bad and slow. I can't open any programs that either, and my pointer always told it to load. Safe mode works, but I just don't know what to do. Help, please

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Since it works fine in safe mode, I suggest you to try to perform the clean boot to safe mode and check if it helps:
  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  Method 2:
  Also, try to run the safe mode System File Checker and check if it helps:
  http://support.Microsoft.com/kb/929833

  Method 3:

  Be sure to run a full scan with your antivirus software.

  http://www.Microsoft.com/security/default.aspx

  It will be useful.

• How can I download my photoshop on my new computer that does not have a hard drive

  How can I download my photoshop on my new computer that does not have a hard drive

  Hello

  What version of Photoshop?

  You can choose and download earlier versions of CC here: other downloads

  Concerning

  Jitendra

• Skype does not load properly and leaves no connection either.

  Hello.

  I recently installed Skype 6.21, however it does not load properly. And it won't let me log in either. I tried to uninstall and reintsalling but still the same. No idea what is the problem? Here's a screenshot of it

  

  Your image is not yet visible. It may take a while before this image is approved by one of the moderators of the community.

  You see something similar to this?

  http://community.Skype.com/T5/Windows-archive/Skype-login-looking-weird/m-p/2258915/highlight/true#M...

• new battery but computer still does not load

  I just bought a new battery and the computer will not charge it. It is said to replace the battery.

  Hello

  Check with the vendor Support from Dell, their documentation online, and battery diagnostics, drivers.
  and ask questions in the Dell forums about known issues. Some manufacturer issued BIOS and other updates
  for help with battery problems.

  -----------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  =================================================================

  Other information that might help:

  Control Panel control - plan change Options - power plans - power - advanced settings
  Parameters for the drainage and the use of parameters (this is how much to use and not how or)
  How long to load).

  In fact, what causes a lot of wear on a battery empties it too low on several occasions. With today
  systems overload are not a problem.

  Here are some tips to help and troubleshoot battery issues.

  Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
  eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
  them and be careful). Batteries are old, or it could be a problem with the computer.
  Check with the support of the machine system, and many of them have online forums.

  New Lithium-Ion type battery usually last longer if you do not unload their less than 30%
  However on a laptop that not extend their life a lot. Best is to use the a/c adapter
  When this is possible.

  I use the free version of BatteryBar to monitor my battery. Click on the green button on the
  Yellow box on the right side of the page to download the latest stable version.

  BatteryBar - free version available
  http://osirisdevelopment.com/BatteryBar/index.html

  Another good program

  Vista battery saver - free
  http://www.codeplex.com/vistabattery

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  You can also check with the manufacturer of system and forums that many use their own
  proprietary software to monitor the battery and they could be known problems with your battery.

  ============================================================

  Taking care of your laptop battery
  http://Windows.Microsoft.com/en-us/Windows7/taking-care-of-your-laptop-battery

  Battery meter: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/battery-meter-frequently-asked-questions

  Battery saver
  http://Windows.Microsoft.com/en-us/Windows7/conserving-battery-power

  Solutions to common battery problems
  http://Windows.Microsoft.com/en-us/Windows7/solutions-to-common-battery-problems

  What is the precise the battery meter?
  http://Windows.Microsoft.com/en-us/Windows7/how-accurate-is-the-battery-meter

  ============================================================

  Try this - to make a Restore Point

  How to create a System Restore Point in Windows 7
  http://www.SevenForums.com/tutorials/697-system-restore-point-create.html

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  Then Control Panel - Manager of devices - Batteries - Double click on each item - drivers - tab
  Update the drivers (which can do nothing) - then do a right click and UNINSTALL each - RESTART
  who will update the driver stacks.

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• embority singer used with old portable new computer laptop does not load software

  I have a sewing machine singer ebrodiry I used with my old laptop with the new laptop dosent load software and it does not recognize the sewing machine which can make

  Hello

  What operating system do you use?

  I suggest you to follow the links and check out them.

  If you use windows vista refer; Make older programs in this version of Windows

  http://Windows.Microsoft.com/en-us/Windows-Vista/make-older-programs-run-in-this-version-of-Windows

  If you use windows7 refer the link and check.

  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows

  I also suggest you to reach the center of singer and check.

  http://answers.Singerco.com/answers/7010/category/embroidery-and-sewing-machines/questions.htm?page=2

• Update Vista crashed my computer - Windows does not load

  I installed the Vista updates this weekend (02/01/09) on my HP Pavilion dv4.  It appeared to download without any problem, but then he asked me if I would like to restart now, and when I did it, Vista will no longer.  The file that it is identified as a problem is WMM2AE.dll.  I took the computer to Best Buy (it is still under warranty), but it seems that I may need to reinstall the operating system.  Does anyone have any suggestions to solve this problem?  Research on the web, it seems that there are MANY problems with Windows updates.

  samantha22,
  I would first try to use the start option last good known in the Advanced Boot options screen.  If this does not work you can use Package Manager to remove the update that was installed.
  Depending on your recovery media, you may be able to perform an installation that would move your current Windows folder and does not erase your information.  But I hope that we won't get to this point.  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP (JEALOUSY?) Desktop computer: PC does not load

  Someone please help, my computer does not start. It starts fine then before loading it asks me to reload my PC to an earlier time were it worked. It shows then the logo at the top and underneath the wheel loading, then the wheel stops, I don't know what to do, any help would be greatly appreciated

  UPDATE: the computer asked me to restore to an earlier date, I did, he said it needs to restart, now it starts all simply not at all it is stuck on the loading screen, please help

• Brand new Dell 2808 router does not work.

  1. the 2808 is not connected to the internet.

  2. when it is received, the 2808 under tension with the disabled DHCP server and port active routing. It is the default setting. Not good to use normal, but worked as advertised. The DHCP server is usually needed in a small switch. I needed an active DHCP service.

  3. I've changed managed and connected fashion. A "saved to restore configuration screen" appeared. Horrible thing. Trashed the router. There is no saved configuration, the 2808 restarts. 2808 completely stopped working after that.

  4. after resetting 2808, the 2808 seemed no longer routing packets, so nothing works now with the exception of the web client, which does not seem to do anything for the networking.

  5 I did activate the DHCP client and configure the IP pool. However, no routed packets, nothing works. Port au port data routing does not work. The DHCP server is not required to allocate IP addresses.

  6. I paid 80 dollars to a so-called "Dell Customer Service" held to solve the problem. They have failed. It turns out that they did not know how to work the 2808.

  7 I have not understood how to contact customer service the Dell directly for the 2808. Not good. I bought a T7810 workstation in 2015 with 5 years of service from Dell, and I don't know how to contact Dell support technical support. I use the 2808 with the T7810. Both should be covered if the customer service could be found.

  8. bottom line, I bought the 2808 on July 27, 2016, and many hours later my effort and more hours of a consultant, I am frustrated trying to run home mode: a router 8-port 1000-baseTpacket with a DHCP Server enabled. I'm about to box 2808 router back to Amazon because it does not work and cannot be implemented.

  Any ideas?

  Thanks in advance to 1 million.

  Keith

  The simplest method to contact support is to enter the serial number on our support site.
  http://Dell.to/20VqlwQ The site will then list the various methods to contact support for this range of products.

  The 2808 PowerConnect doesn't have a console port, so recovery is somewhat limited. If the switch is on firmware version 1.0.0.38 or earlier, then a factory reset can be done by simply changing the transition from managed to not managed and then again. If the switch is on more recent firmware, however, this process does not reset the switch to factory default.

  Being a new switch, it should be under warranty. If the switch is not recoverable, support should be able to get a replacement sent to you.

• All new Satellite L750-22Z does not load

  I bought my new L750 Satellite 22z Friday, since that time I installed Microsoft office and moy. When I turned it off yesterday he said installation of updates.

  When I turned it on today it says that there are 46000 updates to do and showed it running updates for a few minutes, he left for the toshiba leading innovation screen where it is blocked for 4 hours.

  I don't want to force close to the low snack snack that's still making updates, but I don't know what to do and if it is somehow broken. Anyone know what I need to do?

  I agree with kancaras. Install the recovery image again following the instructions on http://aps2.toshiba-tro.de/kb0/HTD1303440001R02.htm

  After doing this you will have own OS preinstalled again and you can start using the laptop with factory again.

  Be careful with the installation of updates. I assume that you are writing about the right Microsoft updates?
  Disable automatic update and before you install check updates are listed.
  Install important updates only.

• Envy 17 t-K200: sudden computer failure - does not load, but the output of the AC charger is OK.

  Recently, I unplugged the power supply current to work elsewhere in the House.  When I reconnected the power running and left the computer had entered a deep sleep mode.  He did wake up, and I could go on until the task was completed.  Yet once I left the computer.  When I came back the screen was dark and I assumed that he had turned on the hibernation mode.  However he would not resume.  I checked the plug on the computer for the light, which would indicate that power is being supplied to the computer.  It was DARK.  Because the power supply is plugged into a power strip, I checked to make sure that the band was on.  The indicator light remains DARK.  I plugged in the power supply into a known powered outlet.  The indicator light remains DARK.  Using a voltmeter, I found that was good and the output at the end the power supply DC showed 19,88 volts C.C.  At this point, I assumed that the power Jack cable harness had broken somehow.

  Research of the internet, support HP and HP forum pages revealed no clear solution.  "I left a message on.

  • HP Support Forum Home
  • >
  • Laptops
  • >
  • Material
  • >
  • "Re: charging pins and broken power connector.

  20/06/16 but have had no answer at this time to propose a telephone conversation.

  Since then, I needed to have access to the information on the hard drive.  Removal of the hard drive means that the upper part of the computer had to be removed.  This gave access to the 'power Jack Cable Harness' and inspection at the end of the beam connection seems to be OK.  Visual inspection of the components gave no clear indication of the problem of overheating or else.

  I am at the limit of what I can see and need help.

  The computer is a HP Envy 17 t-K200 - 17.3 in laptop.  CPUI Intel i7-4720HQ.  The hard drive is 1 TB.  With 12 GB of RAM.  The SN is 6CF518162Z.  The machine is refurbished and is out of warranty as of February 16, 2016.

  Apparently, after running the tests on my computer the conclusion strongly implies a failed motherboard.  Attempts to locate a source of reference 793272-601 (preferred) or part number 793272-501 failed.  Therefore, it seems that I'll be compeled to use the service of repair of HP at a high cost.  The good is that it will be a 'huge' 90 day warranty.

  Thanks to Hüffer for suggestions he made.

• Professional Windows does not see my hard drive during installation and wants to leave the installer.

  installed the new hard drive in my compaq lap top, started the professional windows installation and stops because it cannot find the hard drive. It is in the bios and has passed the tests. My lap top has only a cd/dvd drive, a floppy drive. Not knowing what to do.

  It is probably because you have a hard drive Serial ATA (SATA) in your computer.  These drives did not exist when Windows XP came out and so no drivers for this type of disc can be found in a regular Windows XP don't install.  Windows makes allowances for that by inviting you to press the "F6" key at the beginning of the installation process, but then you must provide the SATA drivers diskette (no other medium will do).

  "Limited OEM driver support is available with F6 during installation of Windows XP and Windows Server 2003"
    <>http://support.Microsoft.com/kb/314859 >

  There, several articles that explain how to install XP on a SATA drive without needing a disk.  Here are a couple of them:

  "Installing Windows XP with AHCI/RAID F6 of USB drivers only"
    <>http://www.Prime-expert.com/articles/B02/installing-Windows-XP-with-F6-AHCI-RAID-drivers-from-USB-only.php >

  "How to install XP on a SATA HARD drive without a floppy for a laptop drive"
    <>http://www.ehow.com/how_7395338_install-HDD-floppy-drive-notebook.html >

  HTH,
  JW

• SMU Chassis or modules appearing does not in NI Instrument Driver Finder/connecte Intstruments

  New user, to debut with a chassis SMU-1073, controlled by a PC, with supply POWER 4113, 4145 SMU and 4071 modules DMM.

  I installed all the drivers from the supplied USB system and I can indeed see/control of the chassis and modules of NI MAX.

  When I try to see the modules Labview 2012 or 2014 (I'm looking for example VI to start) Instrument Driver finder does not show any chassis or modules.

  Looking for support OR but could find no generic "Here's how to start using this box OR $20,000 without flinching" first steps to help.

  So, I was hoping that it was a mistake and plug and play like the other instruments I connected and used. What I am doing wrong?

  

  Do not use the finder of the instrument. Use the help > examples of find and refer to material input and output. Be specific in listing of the drivers you have installed.