New Dell computer, which gives the message "Cannot connect to Delldock" in Vista

Similar Questions

• Just installed a vigin superhub my portable computer that has a network adapter and connected to the hub, but I get the message cannot connect without certificate

  wireless problem

  just installed a vigin superhub my portable computer that has a network adapter and connected to the hub, but I get the message cannot connect without a certificate, any siggestions would be welcome

  Tom

  Hello, Bill Bates,.

  I would say to contact support with their router blank:
  https://help.virginmedia.com/system/selfservice.controller?configuration=1002&PARTITION_ID=1&TIMEZONE_OFFSET=&usertype=1&VM_CUSTOMER_TYPE=&cmd=ESCALATION_REQUEST

• «Caching of connections from domain to Vista laptop fault for * some * users, which gives the message "failure of the trust relationship «»

  Greetings!

  I have a laptop wireless problem Vista Ultimate on a domain that has a strange behavior when taken off site. Of course, I'd appreciate some thoughts on what could be the problem.

  When the laptop is used internally, it works normally and is used by two people. Person "A" is the main user, person "B" is a secondary user who connects is rare. Domain authentication works normally and thankfully.

  Sometimes, however, when the laptop is taken off site and brought in a different wireless network do not have access to the field, strange behavior of logon follows.

  When the person 'A' tries to connect, they receive two messages:

  "The system event Notification Service failed to logon"

  "The trust relationship between this computer and the primary domain failed."

  Yet moments later, what person 'B' opens a session on the same laptop in the same place, the logon succeeds and the laptop runs normally.

  Presumably, the two openings of session would be finished via the credentials cached, so there is no reason at all to imagine that each account should be treated differently. However, it is precisely the situation that I see. Something is apparently originally person 'A' logon to be handled in an unusual way, I can't explain or stop.

  When this laptop is returned to its primary location, resumed normal operation, all users can perform normal logons domain-based, and no errors occur.

  If it was simply a problem of not being on the same wireless network and by far the field, I expect to see something in the sense of a message «could not domain controller be contacted...» ", but this is never; and he would likely by all users, no not one. It behaves almost as if caching credentials for the person 'A' are corrupt or non-existent, neither of which is logical.

  Other portable computers used by many people (using various combinations of XP, Vista and Windows 7) and taken offsite have * never * experienced this problem. They operated with credentials cached just like you would expect.

  I suppose that a complete reconstruction could solve the problem, but I prefer not to go nuclear on this particular area if it is not necessary. There must be an if explainable, eccentric, the mechanism at work here cause this problem.

  Thank you very much in advance for the help.

  -David

  Hello Soonerdave,

  I apologize for the lack of communication. The appropriate forum for post you in is listed below:

  http://social.technet.Microsoft.com/forums/en-us/itprovistanetworking/threads

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Why the message (cannot connect) began to appear and inhibited me subscription to any plan? [iOS]

  Hi, I am really frustrated because I tried to enroll in a plan of Adobe Acrobat application for iPad and this error message started to appear since today! The last days I was agree with you connecting and linking to acrobat cloud!

  Help, please!

  

  Hello

  Currently, Adobe Document Cloud (which uses Acrobat Reader for iOS) seems to not be available.

  Please you go https://cloud.acrobat.com in Safari (or another web browser).  You will see the following message is displayed.

  

  We apologize for the inconvenience.

• Whenever I use the computer, I get the message "install new updates"

  The most recent 2 Win7 security upgrades/downgrades are on my computer. I checked.

  Whenever I use the computer, I get the message "install new updates"

  How to set the flag that says I have miserable things?

  Thank you

  Trevor

  Original title: upgrades

  Hello Tworg,

  Thank you for the update on the question and sorry for a delayed response.

  If your Windows Update history shows that .NET Framework 4.5.1 is installed successfully. If troubleshooting says ' registration for the service is missing or corrupt... not fixed "then you can try the methods provided below and see if help."

  Method 1

  I suggest to reset the Windows Update components and for this, try to run the fixit described in the following article.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058/en-us#LetMeFixItMyselfAlways

  Method 2

  If after performing more high question method persists try to follow the steps described in the following Microsoft article methods.

  Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2

  http://support.Microsoft.com/kb/2509997

  Registry warning : This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  You can use the following link to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756/

  Important:

  Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  I hope this helps. If the problem still persists, post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Thank you.

• IM updating my computer and I want to transer my suite creative adobe on my old computer to my new computer which is the best way to do it?

  IM updating my computer and I want to transer my suite creative adobe on my old computer to my new computer which is the best way to do it?

  You do not... transfer you disable and uninstall on the old computer (if you won't use this computer) and install it on the new computer

  You install exactly in the same way you did the 1st time... Put your disc in the drive, and enter your serial number when asked

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  -Cloud desktop http://helpx.adobe.com/creative-cloud/help/creative-cloud-desktop.html

  -Cloud Getting Started https://helpx.adobe.com/creative-cloud.html

  -you will need to enter your original serial number during the installation for non-Cloud programs

  - or kglad links in response to #1 here can help https://forums.adobe.com/thread/2081216

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

• Computer how unauthorized if it displays the message cannot otherwise clear permission. Please try again after some time

  Computer how unauthorized if it displays the message cannot otherwise clear permission. Please try again after some time

  Remove the license on a computer http://forums.adobe.com/thread/1442423?tstart=0 can help

  -read http://helpx.adobe.com/x-productkb/policy-pricing/error-maxium-acitvation-exceeded.html

• Remove an external USB storage device after the message "cannot delete".

  By clicking on the icon continues to return the message "Cannot delete", even if I closed all programs, expected and checked all the system and maintenance parameters. I always turn off the computer to get the device, which is a real drawback.

  http://support.Microsoft.com/kb/555665 this may help.

• PCG 4A1L LAPTOP COMPUTER WHICH HAVE THE SYSTEM OPERATION

  Ideas:

  • PCG 4A1L LAPTOP COMPUTER WHICH HAVE THE SYSTEM OPERATION
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  I'm sorry to hear that. In a little more detail would be helpful. Crystal Ball (tm) says when you turn on the computer you get an error message that says somethng like "cannot find operating system". If Crystal Ball (tm) is correct, your hard drive is dead or your motherboard is a failure. Pull the drive and put it in a disk enclosure or use an adapter and test it on a working machine.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

  If you can not do the test yourself and/or are uncomfortable opening your computer, take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad).

  If Crystal Ball (tm) was cloudy, please specify exactly what is happening with your computer. MS - MVP - Elephant Boy computers - don't panic!

• I can't delete a game called Float that gives the message waiting. The cross and the oscillation with delete option appear, but it won't when I select Remove. Any ideas please?

  I have a new mini iPad 4. I can't delete a game called Float that gives the message waiting. The cross and the oscillation with delete option appear, but it won't when I select Remove. I don't know how it came to be. Any ideas please? Thank you.

  First try a reset to see if it finishes downloading. Press and hold the home and power buttons until the Apple logo appears. Release the two buttons. Wait until the iPad tour starts on its own.

  Check if you can remove the application. If not go into settings > general > use iCloud and storage > storage > storage management. Wait for the list of apps to open. See if the float is on the list. If it is delete it from there.

• During the installation of Windows 7 or 8.1 using a USB stick - get the message "cannot be installed, it is a GPT.

  Hello

  During the installation of Windows 7 or 8.1 using a USB stick - get the message "cannot be installed, it is a GPT partition.

  I have 64 bit install discs for Win 7 and Win 8.1. These two install on my desktop in duel boot. I made a Flash DRIVE of each disk so I can install it more quickly.

  Problem: I get the cannot install because it is a GPT partition.

  Y at - there no way to make these 2 USB sticks work?

  Thank you, Brad

  Make sure you create your media recovery HP or USB Flash Recovery discs before you edit or change anything.

  Your computer does not have Microsoft's Downgrade rights and you must buy a copy of Windows 7 with a valid Microsoft COA and product key.

  The screenshots below is from a laptop HP 15 t-j100... options and the configuration on your computer screens may differ.

  You will need to DISABLE "Secure Boot" and ENABLE "Legacy Support" in the "Configuration of the BIOS start-up secure" on the settings page similar to what is shown below, until you try to install Windows 7.

  

  After you save the changes, the computer will ask you to confirm the changes... Accept the changes by typing the four digit code and press the ENTER"" key.

  

  If you install Windows 7 from a USB and see a message of "load a driver - a required CD/DVD drive device is missing", it's because as 'System Configuration' > 'Config USB3.0 in pre-start' is set to 'Enabled '. This should be set to 'Auto '.

  

  In addition, as the factory hard drive is partitioned as TPG, you must start using the internal CD/DVD UEFI or UEFI-Key/key USB to install Windows on a GPT-partitioned disk. Turn on or restart the computer and press "F9" or "ESC", then "F9" when prompted. Select the source of boot UEFI you use and you press "ENTER".

  

  I suggest using Windows 7 SP1 for the best installation experience. If the DVD does not start as UEFI, you may need to use a USB Flash drive (can ask "Quick start" DISABLING in BIOS) as the installation media. Please note that some computers may not recognize a valid active UEFI USB Flash drive if it is formatted in NTFS and may require only a FAT32 formatted USB Flash drive. You should be able to make a FAT32 formatted Windows 7 installation USB Flash drive using Rufus, UNetbootin, Universal USB Installeror WiNToBootic. I like Rufus, because it contains options for 'Plan of GPT partition for UEFI computer' and 'FAT32'.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Is it possible that I can install American greeting Creatacard Plus on my new Dell computer

  Installation of the program

  Is there a way I can install American greeting Creatacard Plus on my new Dell computer.  I had it installed on my old computer and love the program and don't want to lose him.  I have a lot of data that I will be unable to replace also unless I transfer program.  Dell indicates that the program is incompatible with his system, and that's why I can't install it.  There must be a way that it can be made compatible so I can install it.  Please notify.

  Contact support American greeting Creatacard.

• Whenever I start my computer, I see the message, "C:\Windows1\Kjoralir.dll" is missing.

  Whenever I start my computer, I see the message, "C:\Windows1\Kjoralir.dll" is missing.  This happened for several months, but I just ignored him.  Don't know if it's related, but a user cannot disconnect without pressing the Windows key and the "L" key at the same time.

  Tonight I ran a registry repair program, and it fixed a lot of errors.  But, always, the message came after a reboot.  I don't know what it is, what it does or how to remedy the situation. Can anyone help?

  Thank you!

  You may have damaged even more by running a registry cleaner for Windows. The best registry cleaners are snake oil, and at worst they will damage MS Office and sometimes Windows itself. Details:

  http://aumha.NET/viewtopic.php?t=28099

  For the problem, Googling for this file appears your post. When you get no hits for a filename on Google, chances are high that it is a malicious program file. Either you have uninstalled the malware program or your antivirus/antispyware program did. In all cases, a reference has been left in the boot file. You can remove the reference by managing your startup.

  Because you had a piece of malware, the chances are too high you had others. It would be a good idea to scan. I recommend to download and install MalwareBytes' anti-malware (MBAM) from http://www.malwarebytes.org . The program is free. (There is a paid version, but you don't need to buy it to remove the malware).

  Manage startup:

  (for XP) Start > run > msconfig [Enter]

  This will open the System Configuration utility. Look under the Startup tab and find the likely culprit. Uncheck the box next to its name, apply and OK out. You don't need to restart immediately, but next time you do, you will get a dialog box saying that you have used the utility. Just check the box that says in effect, "don't mind to this subject again".

  How to troubleshoot by using the Msconfig in Windows XP utility - http://support.microsoft.com/?id=310560

  The free Autoruns program is very useful for managing your Startup - http://www.microsoft.com/technet/sysinternals/default.mspx
  MS - MVP - Elephant Boy computers - don't panic!

• I can't connect on the profile of the main user, the computer indicates that the profile cannot be loaded. How can I fix?

  original title: user profile

  I can't connect on the profile of the main user, the computer indicates that the profile cannot be loaded. How can I fix?

  Hello

  You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. The ADMIN account in trunk
  Mode has no default password (unless someone has changed the password so it should be available).

  Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google Earth)
  has been known to cause this problem.

  Error message when you log on a Windows Vista-based or Windows 7 using computer a
  Temporary profile: "the user profile Service has no logon. Unable to load the user profile.
  http://support.Microsoft.com/kb/947215

  How to fix error "the user profile Service has no logon. User profile cannot be loaded. »
  http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.html

  How to fix error "your user profile was not loaded correctly! You have been connected with a
  temporary profile. "in Vista
  http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.html

  BE VERY CAREFUL IF YOU USE THIS ONE:

  DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrrups you are TOAST.

  How to enable or disable the real built-in Administrator account in Vista
  http://www.Vistax64.com/tutorials/67567-administrator-account.html

  Use the Admin account hidden to lower your user account APPLY / OK then wear again to
  ADMIN. This allows clear of corruption. Do the same for other accounts if necessary after the
  above message.

  You can use the hidden - administrator account to make another account as an ADMINISTRATOR with your same
  password (or two with the same password) use a test or difficulty to another.

  You can run the Admin account hidden from the prompt by if necessary.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  If you cannot access your old account, you can still use an Admin to migrate to another (don't forget
  always leave to an Admin who is not used except for testing and difficulty account).

  Difficulty of a corrupted user profile
  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• C7280 when I try to install from cd, I get the message cannot find 7cS5B3C

  When the cd-rom for c7280 hpdriver instaaling I get the message cannot find

  c;\users\huubs\AppData\local\temp\7cS5B3C\setup\...\setup\block [next illegible]

  And it stops

  Huub

  Hello huubs

  Try the following to "scrub" your machine HP printing software. This should clean your computer so that you can re - install the printer as if it was never installed previously. Sometimes this solves problems with the driver.

  Of the Original installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. If you have an HP computer, run the L3uninstall.bat. If you have a computer not HP, run the L4uninstall.bat

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://get.Adobe.com/flashplayer/

  9 download drivers and full software features

  Photosmart C7280 Full Feature software (Windows 7)

  10. run the download to reinstall the printer

  If the software has been downloaded and extracted to your system:

  1. type % temp % in the field of race

  2. Locate and open the folder starting with 7z (example: 7zS2356)

  3 open the Util folder

  4 open the CCC folder

  5. If you have an HP computer, run the L3uninstall.bat. If you have a computer not HP, run the L4uninstall.bat

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://get.Adobe.com/flashplayer/

  9 download drivers and full software features

  Photosmart C7280 Full Feature software (Windows 7)

  10. run the download to reinstall the printer