New GE Skype Wireless not dial a number
account called the mobile phones or regular computer very well. Set up wireless with the same account and he answers the call, but do not dial. You compose here but no ring or you connect.
Unfortunately, this is a known issue with this phone, and no one reported a solution. It does not all credits for the call, but insists on the fact that you have some and makes you pass through this circle if your balance is less than a threshold. For now, at least, the only solution is to buy credits you can never use.
Tags: Skype
Similar Questions
-
SPA3102 will not dial a number, or forward calls to Elastix
For the past 2 days, I am trying to get this SPA 3102 to work as a PSTN gateway but no luck... My network is 172.16.1.0/24. My default gateway is 172.16.1.1 and local IP address of the SPA is 172.16.1.200. Elastix server is 172.16.1.8. I don't have any other VOIP providers so I na not configure my WAN for SPA settings (Nothing connected to the WAN port)
Here are the screenshots and my config settings:
The SIP Trunk settings:
Outbound caller ID: 383579 (my local PSTN number)
Chanels maximum: 1
Name of the Trunk: pstn
Parameters of peers:
do not allow = all
allow = ulaw
Polycom = no
context = of-RTC
dtmfmode = rfc2833
Host = 172.16.1.200
incominglimit = 1
NAT = never
port = 5061
qualify = yes
secret = 300
type = friend
username = pstn
Entrants settins empy rest under vacuumRoad of basketing:
DID number: 383579
Transfer the call to ext: 205
rest is default or is empty
Line1 SPA is disabled because I want just difficulty dailing and receive phone calls.
Here are a few screenshots of RTC in SPA line configuration:
As see you in picture above I have sound but spa isn't answer...
It comes from the phew journal asterisk call out:
-[358291@from-internal:1] Macro execution ("SIP/205-087af3d8","user-callerid |") SKIPTTL | ") in new stack
-Execution [s@macro-user-callerid:1] Set ("SIP/205-087af3d8", "AMPUSER = 205") in new stack
-Execution [s@macro-user-callerid:2] GotoIf ("SIP/205-087af3d8","0?") report") in new stack
-[S@macro-user-callerid:3] ExecIf execution ("SIP/205-087af3d8","1" | ") The value | REALCALLERIDNUM = 205 ") in new stack
-Execution [s@macro-user-callerid:4] Set ("SIP/205-087af3d8", "AMPUSER = 205") in new stack
-Execution [s@macro-user-callerid:5] Set ("SIP/205-087af3d8", "AMPUSERCIDNAME = Damir here") in new stack
-Execution [s@macro-user-callerid:6] GotoIf ("SIP/205-087af3d8","0?") report") in new stack
-Execution [s@macro-user-callerid:7] Set ("SIP/205-087af3d8", "AMPUSERCID = 205") in new stack
-Execution [s@macro-user-callerid:8] Set ("SIP/205-087af3d8", "CALLERID (all) ="Damir Reic ' <205>' ") in new stack
-Execution [s@macro-user-callerid:9] Set ("SIP/205-087af3d8", "REALCALLERIDNUM = 205") in new stack
-[S@macro-user-callerid:10] ExecIf execution ("SIP/205-087af3d8","0 |") The value | Channel (Language) = ") in new stack"
-Execution [s@macro-user-callerid:11] GotoIf ("SIP/205-087af3d8","1?") continue ") in new stack"
-Goto (macro-utilisateur-callerid, s, 20)
-Execution [s@macro-user-callerid:20] NoOp ("SIP/205-087af3d8","Using CallerID"Damir Reic" <205>" "") in new stack
-Execution [358291@from-internal:2] Set ("SIP/205-087af3d8", "_NODEST =") in new stack
-[358291@from-internal:3] Macro execution ("SIP/205-087af3d8","record-enable |") 205. OFF | ") in new stack
-Execution [s@macro-record-enable:1] GotoIf ("SIP/205-087af3d8","1?") check ") in new stack"
-Goto (macro-record-enable, s, 4)
-AGI [s@macro-record-enable:4] performance ("SIP/205-087af3d8","recordingcheck |") 20090827 205946 | 1251399586.64 ") in new stack"
-Launch Script AGI/var/lib/asterisk/acted-bin/recordingcheck
recordingcheck |-205946 20090827 | 1251399586.64: outgoing recording not enabled
-Recordingcheck AGI completed Script, return 0
-Execution [s@macro-record-enable:5] MacroExit ("SIP/205-087af3d8","" "") in new stack
-[358291@from-internal:4] Macro execution ("SIP/205-087af3d8","dialout-trunk |") 2. 358291 | ") in new stack"
-Execution [s@macro-dialout-trunk:1] Set ("SIP/205-087af3d8", "DIAL_TRUNK = 2") in new stack
-Execution [s@macro-dialout-trunk:2] GosubIf ("SIP/205-087af3d8","0?") Sub-pincheck | s | 1 ") in new stack"
-Execution [s@macro-dialout-trunk:3] GotoIf ("SIP/205-087af3d8","0?") disabletrunk | 1 ") in new stack"
-Execution [s@macro-dialout-trunk:4] Set ("SIP/205-087af3d8", "DIAL_NUMBER = 358291") in new stack205>205>
-Execution [s@macro-dialout-trunk:5] Set ("SIP/205-087af3d8", "DIAL_TRUNK_OPTIONS = tr") in new stack
-Execution [s@macro-dialout-trunk:6] Set ("SIP/205-087af3d8", "OUTBOUND_GROUP = OUT_2") in new stack
-Execution [s@macro-dialout-trunk:7] GotoIf ("SIP/205-087af3d8","0?") nomax ") in new stack"
-Execution [s@macro-dialout-trunk:8] GotoIf ("SIP/205-087af3d8","0?") chanfull ") in new stack"
-Execution [s@macro-dialout-trunk:9] GotoIf ("SIP/205-087af3d8","0?") skipoutcid ") in new stack"
-Execution [s@macro-dialout-trunk:10] Set ("SIP/205-087af3d8", "DIAL_TRUNK_OPTIONS =") in new stack
-[S@macro-dialout-trunk:11] Macro execution ("SIP/205-087af3d8","outbound callerid |") 2 ") in new stack"
-[S@macro-outbound-callerid:1] ExecIf execution ("SIP/205-087af3d8","0 |") SetCallerPres | ") in new stack
-[S@macro-outbound-callerid:2] ExecIf execution ("SIP/205-087af3d8","0 |") The value | REALCALLERIDNUM = 205 ") in new stack
-Execution [s@macro-outbound-callerid:3] GotoIf ("SIP/205-087af3d8","1?") normcid ") in new stack"
-Goto (macro-sortant-callerid, s, 6)
-Execution [s@macro-outbound-callerid:6] Set ("SIP/205-087af3d8", "USEROUTCID =") in new stack
-Execution [s@macro-outbound-callerid:7] Set ("SIP/205-087af3d8", "EMERGENCYCID =") in new stack
-Execution [s@macro-outbound-callerid:8] Set ("SIP/205-087af3d8", "TRUNKOUTCID = 383597") in new stack
-Execution [s@macro-outbound-callerid:9] GotoIf ("SIP/205-087af3d8","1?") trunkcid ") in new stack"
-Goto (macro-sortant-callerid, s, 12)
-[S@macro-outbound-callerid:12] ExecIf execution ("SIP/205-087af3d8","1" | ") The value | CALLERID (All) = 383597 ") in new stack
-Execution [s@macro-outbound-callerid:13] GotoIf ("SIP/205-087af3d8","1?") output ") in new stack"
-Goto (macro-sortant-callerid, s, 11)
-Execution [s@macro-outbound-callerid:11] MacroExit ("SIP/205-087af3d8","" "") in new stack
-[S@macro-dialout-trunk:12] ExecIf execution ("SIP/205-087af3d8","1" | ") AGI | fixlocalprefix") in new stack
-Launch Script AGI/var/lib/asterisk/acted-bin/fixlocalprefix
> fixlocalprefix: using chart 0 + [0] [9] X.
> fixlocalprefix: using mires NXXXXX 0 +.
== fixlocalprefix: Dialpattern 0 + NXXXXX matched. 358291-> 0358291
-Fixlocalprefix AGI completed Script, return 0
-Execution [s@macro-dialout-trunk:13] Set ("SIP/205-087af3d8", "OUTNUM = 0358291") in new stack
-Execution [s@macro-dialout-trunk:14] Set ("SIP/205-087af3d8", "custom = SIP/pstn") in new stack
-[S@macro-dialout-trunk:15] ExecIf execution ("SIP/205-087af3d8","0 |") The value | DIAL_TRUNK_OPTIONS = M(setmusic^) ") in new stack"
-[S@macro-dialout-trunk:16] Macro execution ("SIP/205-087af3d8","dialout-trunk-predial-crochet |" "") in the new battery
-Execution [s@macro-dialout-trunk-predial-hook:1] MacroExit ("SIP/205-087af3d8","" "") in new stack
-Execution [s@macro-dialout-trunk:17] GotoIf ("SIP/205-087af3d8","0?") bypass | 1 ") in new stack"
-Execution [s@macro-dialout-trunk:18] GotoIf ("SIP/205-087af3d8","0?") customtrunk ") in new stack"
-Execution [s@macro-dialout-trunk:19] Dial ("SIP/205-087af3d8","SIP/pstn/0358291 |") 300. ") in new stack"
-Called pstn/0358291
-SIP/pstn - 0885 has 138 sounds
-SIP/pstn - 0885 has 138 replied SIP/205-087af3d8
-Packet2Packet bypass 087af3d8/205-SIP and SIP/pstn - 0885 has 138
-Remote UNIX connection
-Connection to UNIX distance disconnected
-[H@macro-dialout-trunk:1] Macro execution ("SIP/205-087af3d8","hangupcall:" "") in the new battery
-Execution [s@macro-hangupcall:1] ResetCDR ("SIP/205-087af3d8", "w") in new stack
-Execution [s@macro-hangupcall:2] NoCDR ("SIP/205-087af3d8","" "") in new stack
-Execution [s@macro-hangupcall:3] GotoIf ("SIP/205-087af3d8","1?") skiprg ") in new stack"
-Goto (macro-hangupcall, s, 6)
-Execution [s@macro-hangupcall:6] GotoIf ("SIP/205-087af3d8","1?") skipblkvm ") in new stack"
-Goto (macro-hangupcall, s, 9)
-Execution [s@macro-hangupcall:9] GotoIf ("SIP/205-087af3d8","1?") theEnd ") in new stack"
-Goto (macro-hangupcall, s, 11)
-Execution [s@macro-hangupcall:11] Hangup ("SIP/205-087af3d8","" "") in new stack
== Spawn extension (macro-hangupcall, s, 11) exited non-zero on "SIP/205-087af3d8" in the macro 'hangupcall '.
== Spawn extension h (macro-dialout-trunk, h, 1) exited non-zero on 'SIP/205-087af3d8.
== Spawn extension (macro-dialout-trunk, s, 19) exited non-zero on 'SIP/205-087af3d8"macro"dialout-trunk.
== Spawn extension (of-internal, 358291, 4) exited non-zero on 'SIP/205-087af3d8.As you can see he composed, if found the dialing rule, but nothing happens on the SPA, it will not simply compose anything on.
I guess that something is wrong in RTC spa or configuration of trunk, but I don't know what. I tried like 5-6 guides of strach and none worked for me. Any suggestions?
Kind regards
Damir
HUH! I won't curse now, but I shoul!
Given that I'm NOT using any VOIP provider and I JUST wanted to use RTC it makes SENSE I don't connect anything to the WAN port, BUT when I configured the WAN port with my LAN IP (172.16.1.200) and put a few other IP on the LAN port, everything started working.
It's rly rly rly is NOT logical, but I got it working now.
-
Dear friends, I am struggling to dial any phone number. When I press on the symbol of the dial, it immediately returns the error message 'arrested contacts' - ' o is parou - in Portuguese.
I already tried to clean the cache and the data of all the apps, tried the hard reset and still the same error. What could possibly be wrong? The errors began after I composed a total of 16 numbers huge telefone number (XX XX xxx xxx xxx xxx). Could it be related to that?
Thank you all!
Billy of the Brazil!Hello
Dialing a long number should not affect the Dialer in this way. I suggest you factory reset on your phone via the settings > Backup & reset > reset data. Before you do a factory reset, you might want to backup your data.
-
Can not dial AOL and broadband is very slow.
I have a 2 year old Toshiba laptop. Recently, he has been making slower and slower when it is connected to the internet. Yesterday he could not dial the number of AOL and said that he had no dial tone. However, if I listen carefully, I can hear the familiar beep and recording that says "If you want to make a call Please hang up and redial." (this is what happens when a phone is off the hook) Anyway, frustrated, I went to my neighbors who have broadband service, and the laptop is slower than molasses when on the internet through their broadband services. The laptop works at speeds normal when not online. I tried system restore to an earlier date... no help. Then I reinstalled the entire system and still can not dial AOL.
Any help would be appreciated! :-)
It is a symptom of severe infection so start by analyzing carefully:
http://www.elephantboycomputers.com/page2.html#Removing_Malware
If you can't do the work yourself (and there is no shame in admitting this isn't your cup of tea), take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad). Please be aware that not all shops are skilled at removing malware, and even if they are, your computer may be so infested that Windows will have to be properly installed. If possible, have all your data backed up before taking the machine into a shop.
MS - MVP - Elephant Boy computers - don't panic!
-
Citing the phone to dial a number
I'm trying to dial a phone number of my app running on my BB Z10. I was able to launch the phone application and bring it to focus, but it does not dial the number. I have tried the following to dial in number 9999:
navigator_invoke_invocation_create (& iRequest);
navigator_invoke_invocation_set_id (iRequest, '1');
navigator_invoke_invocation_set_action (iRequest, 'bb.action.DIAL');
navigator_invoke_invocation_set_type (iRequest, 'application/vnd.blackberry.phone.startcall');
"{" string data = '{\"number\': \"9999\ '} ';
navigator_invoke_invocation_set_data (iRequest, data.c_str (), data.length ());
navigator_invoke_invocation_send (iRequest);
navigator_invoke_invocation_destroy (iRequest);
I also tried sending as URI instead of the data :
navigator_invoke_invocation_create (& iRequest);
navigator_invoke_invocation_set_id (iRequest, '1');
navigator_invoke_invocation_set_action (iRequest, 'bb.action.DIAL');
navigator_invoke_invocation_set_type (iRequest, 'application/vnd.blackberry.phone.startcall');
navigator_invoke_invocation_set_uri (iRequest, ' data : //local?number=9999 ");
navigator_invoke_invocation_send (iRequest);
navigator_invoke_invocation_destroy (iRequest);
In both cases, the phone will appear but do not dial.
You could do that.
Phone phone; phone.initiateCellularCall(number);
With the help of the class of phone.
https://developer.BlackBerry.com/Cascades/reference/bb__system__phone__phone.html
-
iPhone 5-can't dial a number with Skype credit
I loaded and set up my iPhone from iTunes 5 and he transferred transparently all my data and applications from my iPhone 4. When I tried to dial a number on Skype credit there is no result. I was allowed to call out on my old phone on my wireless network. The new phone is also connected via wi - fi. What do I need to uninstall Skype with the new phone and then reinstall? Any suggestions?
I fixed it. I had to disconnect, then reconnect and it should now connect.
-
Skype to the Japan number - call is OK but call the receiver can not see my number
Hi all.
Today I received number of Skype to the Japan, receiving another appeal is OK but when bringing in another receiver can not see my number. I went to the caller identification settings and cannot see the Japan in the list, while number of Skype to the Japan cannot do that, right?
Thanks for reading.
Update: I received Skype confirmatiom. It is correct. Caller ID cannot be used in the Japan.
-
Received my brother in laws laptop cannot connect wireless, although I can of my own laptop. Trying to connect through the new laptop, I do not see even my own network! What I'm missing here? I'm sure it's maybe something simple, but for the life of me! (When my brother-in-law used this computer, he only uses it through dialup (!), he lives in a remote area). With the help of Vista, and when 'Management of connections' I see my network...
original title: cannot connect wirelessHello
· You get the error message?
Method 1:
I suggest you update the drivers for hardware connected to your computer on the Web site of the manufacturer check if it works.
Updated a hardware driver that is not working properly
Method 2:
Also, follow the steps in troubleshooting section and check if that helps:
In the Windows wireless network connection problems
http://Windows.Microsoft.com/en-us/Windows/help/wireless-network-connection-problems-in-Windows
Check out these links and check if that helps
http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router
http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network
See also:
Solve problems with computers not appearing is not in the network mapHope this helps
-
Hi, I tried to download Photoshop CS5 on new Macbook but received message: this serial number is not valid for this product. Previously, it has been installed on the PC.
Purchase http://www.adobe.com/in/products/photoshop-premiere-elements.html
-
Running older Acrobat Pro 9 on laptop v. It crashed. I do not have access to inactivate. Have a new laptop and have taken the serial number when he asks the trial version. He rejects as it is an outdated version. Called service and they continue to direct me to the cat «get help» I only stay 7 days before the crashes of the trial version and would like to help. Without having to spend $400 for a new product.
Just before installing the new Acrobat without buying it. Your serial number will only be for 9.0. And there will be no support, it was long after the end of life. Use your original disks.
-
I tried to install my ps cs6 on my new computer, after I entered the serial number, I got the massage, the serial number is not valid
Installs on the Photoshop forum.
-
Try to install adobe photoshop elements 7.0 on the new computer. Will not accept the original serial number?
Move the thread to Photoshop Elements
-
I have PSE 7 and with official serial number. I have a new laptop and I can not install PES. I'll gett a mistake: not good serial number... I uninstalled the PSE from my old computer software. Can someone help me?
To locate the serial number:
----------------------------
http://helpx.Adobe.com/x-productkb/global/find-serial-number.html
Error "serial number is not valid for this product". Creative Suite
http://helpx.Adobe.com/Creative-Suite/KB/error-serial-number-valid-product.htmlError failed to validate the serial number | CS6
http://helpx.Adobe.com/Creative-Suite/KB/unable-validate-serial-number-CCM.html -
frequently viewed topics report does not increase the number of new hit
Hi experts,
I have a project published on RH 9 server with webhelp pro. the frequent search term gives me reasonable counties, each time when the same search term, the number has increased. but the report of frequently viewed topics does not increase the number for the topic I clicked several times (whenever I have click on another topic and then return to click on the same subject). adobe support told me that I should close the window, then re - open the link and click again on the topic, but it still doesn't work. We finally know is that I have to delete all historical data in the cache and reopen the window, then click on the same subject, then the County will go through one.
I wonder if this behavior is normal or not. If it is normal, how to use this report?
Thank you
Frances
Hi Frances.
I'm not an expert in browser, but it seems plausible. The browser cache is designed to avoid having to download content locally whenever a page is opened. Whenever a page is open to scrutiny is conducted to determine if the cache already contains elements of it. If it has, it uses this local version. With the local HR server as the version of the cache statistics are not being updated, because the page is not viewed from the server.
It may be an idea to set your browser options to delete the history of every time that it is closed. Also, be aware that it is possible that different browsers may have slightly different options.
Colum
-
Skype will not download to computer windows 10
Every time it says in the cant connect or reach the download server and just keeps offering new downloads that do not work im until number 9 without success
Try to download and install Skype by using the links below, the first two downloads are full installers:
Maybe you are looking for
-
Store using 3 Canvio external to internal - data seems to be encrypted
Hey,. I bought a put ext hdd my data on it and the usb controller is gone-. -.Now, I want to get my retrospective data, obtained the drive hard toshiba from its holster and put it on a sata internal but now I had a problem. The data appear to be encr
-
Pavilion 127c 550: 550-127 Office c a 10-7800 wakes up from sleep
I just got a desktop with windows 10 computer and it worked fine for 2 days. Now, when he goes to sleep he is unresponsive to the mouse or keyboard to wake up. I completely close and restart to make it work. Support online resources can not downlo
-
Swap processors for Lenovo X 230 and 220 X
My friend has a spare Lenovo X 230 with Intel i5 - 3210 M CPU and I own a Lenovo X 220 with Intel i5 - 2430M CPU. My X 220 have a terrible Intel HD 3000 Graphics installed and I like the performance gain that the Intel HD 4000 can give me. Because my
-
Defragment my personal computer.
I can't defragment my personal computer. It is said to run Chkdsk /f. I tried to run several times, and nothing happens.
-
still can not formatt the usb, the message I get is: the format failed. WHAT SHOULD I DO NOW?