New hard disk identified but causes the error "no boot device found".

Similar Questions

• Reinstall all the software on the new hard disk, Acrobat downloaded in the history of the order and he said the serial number does not match

  I just had to restore my computer from scratch.  I have redownloaded XI of Acrobat Standard of my history page to control on Adobe's Web site with serial number in my order history page.

  It gives me the error that the serial number is valid, but does not match the software on the computer.  He invites me to select another but Acrobat Standard XI isn't in the drop-down list.  I tried everything in the list and he said that they do not match.

  How is that possible?  What should I do?

  I recognize the problem you describe. Simply, you install an upgrade. The product "calling" it asks for is the OLDER version of Acrobat that gives you right to the upgrade. You must now enter your serial number for Acrobat X or 9, to prove eligibility.

• I get the message "No. Boot Device Detected" in Vista

  I changed the battery in Dell Dimension e521 my mother.  Then when booting I get the message "No boot device found". I can continue and boot from the CD.  I tried to Dothe StartRepair bt he indicated there is no problems.  How can I fant6mes the startup problem?

  Hello

  Installation/configuration (BIOS/CMOS) often F2 as you boot then watch the screen - make sure that the hard drive is set
  first of all in the boot order.

  Check with Support from Dell, their online documentation, diagnosis and ask in their forums on any
  known issues.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• G8 Pavilion laptop hardware error - new hard disk?

  Hello, I spoke with a representative from HP and I wanted a second opinion. Here are the facts:

  Possible virus causing the model to be very slow and have errors at the start up.

  Problems of gel even in "safe mode".

  Decided to do a "System Restore" using F8. Follow-up of the steps, took 20 + minutes, FINISHED.

  A screen says that I can, "1. update of security for HP and microsoft;   2 re - install any other software;    3. install all the backed up files. I selected 'NEXT' at the bottom of the screen, then, "OPERATING SYSTEM not FOUND '. Now I can't other than 'F' screens anyhere

  I call HP. A rep tells me to use F2, test drive. On a quick scan, 1 hard disk failure (SMART disc is OK). The full scan, 1 hard disk failure (SMART disc is OK).  The representative asked me a long code determine the failures, and there is NOT.  I go out of the main system diagnostics page and there are two failure codes: 303 (quick scan) and 305 (full scan). The rep wants codes any longer, but there is not.

  My question: do I need a new hard drive, or I can just recovery disks?

  Thanks for any help you can provide!   -Sarah

  Hello

  Longer code (up to 24 characters) means that the HARD disk is dead. 305 error would indicate that your hard drive is defective and must be replaced. Please backup your files/data as soon as possible. Is your machine still under warranty? In the affirmative, please call HP for a replacement.

  Update: Sorry, I'm a little slow - 3rd opinion then.

  Kind regards.

• Satellite l.660-12 q - would the recovery disk rebuild the new HARD disk with a new recovery partition

  Talk about confusion. Does anyone know how to get a Toshiba C660 work after the HARD drive failed and the owner has stupidly NOT followed the instructions to make a recovery disk. Will be the recovery disk (if buy you one from Toshiba) rebuild the new HARD disk with a new recovery partition and install windows 7 (original OS) and accept the product key printed on the Windows license, attached to the base of the laptop. I have read a number of suggestions, but these have been considered incorrect by others.

  Surely, Toshiba must have a way to sort this problem.

  They read these messages?

  Hey Buddy

  I don't think it's really complicated, that I could find all the information about the recovery procedure in the user's manual

  The recovery disk must be created on the first day of purchase its recommended to create one in case something would be wrong with the HARD drive.

  The recovery disk contains an image. The image is a package containing Win system, drivers, tools and all the stuff pre-installed on the notebook.
  You bought the laptop and the system has already been activated so that you have need of t the key placed at the bottom of the unit.
  In addition, the use of the recovery disc formats the drive HARD integer (partitions too) and set the laptop in the same condition as at the first day of the purchase.

  There is also another option to recover the notebook called HARD drive recovery. This HARD drive recovery requires no recovery disk. The recovery disc HARD would be to use format ONLY partition C (System).

• My MacBook Pro suddenly crashed. I lost all the programs, including InDesign CS6 I use the most. I installed a new hard disk, can't find my license number. How can I install CC? Adobe does not accept my address, no credit card no etc.

  My MacBook Pro suddenly crashed. I lost all the programs, including InDesign CS6 I use the most. I installed a new hard disk, can't find my license number. How can I install CC? Adobe does not accept my address, no credit card no etc.

  Find your http://helpx.adobe.com/x-productkb/global/find-serial-number.html serial No.

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

• I tried to reload a CS3 program previously downloaded on my new hard drive and this is the message when I click the English link for Mac products: HTTP ERROR: 404 /support/downloads/dlm/main.jsp RequestURI=/support/downloads/dlm/main.jsp

  I tried to reload a CS3 program previously downloaded on my new hard drive and this is the message when I click the English link for Mac products: HTTP ERROR: 404 /support/downloads/dlm/main.jsp RequestURI=/support/downloads/dlm/main.jsp

  Make sure you have cookies enabled for your browser.  Try using a different browser if the problem persists.

• can not get the new hard drive to work in the Pavilion ze4805us laptop

  have an HP pavilion ze4805us laptop which had a total hard drive failure... recovery disks were lost in a fire... replaced the hard drive with a Western Digital 250 GB drive... computer recognizes the drive, but with only 137 GB... impossible to obtain the Windows Millennium disk to install... I have it get the PXE - E61 error code... have looked for answers and tried a few suggestions to fix the error code, but no luck so far... would like to throw this laptop and runs again, it was so nice all in operation. Can someone help me with this? Thanks to all in advance... rrcar6

  At the level of the BIOS, HARD drive should show the full capacity regardless of the distribution, but it will be limited based on what the current logical block installed the BIOS supports.  For example, the 250 GB HDD Needs LBA 48 bit to be recognized by the BIOS in its entirety.  Western Digital only provides downloads of software and support going back to Windows XP.  Windows Millennium Edition is not able to recognize the full capacity of the drive.  Finding drivers compatible with Windows ME is perhaps another challenge that XP uses a different architecture than Windows ME done.

  It seems that this laptop is the same time that the books mentioned in this thread.  Response from JackShack gives the best explanation as to why he shows quite different in the BIOS.  It has been many years, but I do not remember that the capacity of the HARD disk had exceeded what the BIOS at the time supported resulting in the 137 GB limit displayed in the BIOS.  This section of Western Digital shows that this problem is related to the operating system or BIOS supporting however, this should not prevent Windows to install correctly.

  I'm sure it's already done, as it was not a new BIOS since 2004, but guarantee the newest BIOS is installed.  Logical block address 48 bits, necessary for the larger disks (larger for the time) was released in 2003.  The 2004 related BIOS earlier than probably took supported LBA.  What is the current version of BIOS?

  What is the exact message that you get when you try to install Windows Millennium Edition?

• Drive SMART hard disk error no boot device

  I have a HP pavilion dv7-4170us, and I got an error when I turn it on. I finally bought a new hard drive to replace my hard drive but now nothing works. It says error hard drive SMART, it detects an imminent failure and I needed to back up the content and then run a hard drive test in the diagnostic system. I did a test drive and it says failure with failure id: product GG3SXH-5JW77L-XDOO3F-609AO3 id: XH1O4UA #ABA. I can get anywhere on my computer to save anything and when I turn on the hard disk, it is said to put a bootable device but I did not. Help, please!

  No, I just needed to get revovery media dvd and then I have can use my new HDD is I did fjnd but thanks!

• When I try to create a new folder of file I get the error Code 0 x 80070570

  When I try to create a new folder of file I get the error Code 0 x 80070570

  Hello Denny,

  
  Thanks for the reply with the State of the question, sorry for the caused incontinence.
  I suggest you follow the suggestion of Babu V replied on 16 may 2013
  Reference:
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-files/unable-to-create-a-new-folder-in-c-drive-get-the/75bbf947-094a-45E6-baf6-6b188f8d8ca0

  CHKDSK WARNING: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Please respond with the State of the question of assistance in
  Windows.

• New hard disk and overcommitment WARNING

  I'm trying to add a new hard disk to a virtual computer on a NFS datastore that applies a provisioning. Our NFS volumes are set to auto grow, if they reach a certain threshold. This normally isn't a problem, and so over-provisioning us like crazy.

  Recently, however, we encountered a problem when a new hard drive size exceeds free space in the data store. He responds with the following error (creation of a to 1.99 VMDK):

  PowerCLI D:\ > new-disk-hard - VM $vm - CapacityGB (1.99 * 1024)-$datastore data store

  New-hard drive: 04/08/2014-10:44:09 new-harddisk for the VirtualMachine-vm-10964 entity failed with the following message: "not enough disk space on the data store"datastore1".»

  Perform the same task in the vSphere Client generates the following warning, which can be bypassed by clicking 'OK ':

  

  I tried to create a smaller drive and increase it, but I get the same error. I do not see a - Force parameter or anything equivalent. Is it possible to approve via PowerCLI?

  The ThinProvisioned switch is an option, or which is in conflict with the NFS configuration?

• Re: How to install Windows from a recovery on a new hard disk media?

  Immediately after a Windows Update, my computer will not re-start. It says disk error.

  I could not start it from the recovery media and F8 would not work. I bought and installed a new hard drive. Now, when I put in the recovery media to install Windows on the new drive, it gives an error message.

  What this may be? Would I be able to install Windows from the recovery media?
  It is Windows 7 and laptop Satellite A500, 64 bit.

  Hello

  In General, you can install Recovery on each compatible HARD drive image so you should not be a problem in this regard.

  Please tell us what happens when you start installation of recovery. What error message?

  New HARD drive is recognized in the BIOS. Before you begin installation of recovery BIOS default value.

• I have a laptop Acer Aspire 5349. I just put in a new hard drive and I bought the Acer recovery

  I put the system disk in my cd drive, but it does not start. I looked in my bios and I see my cd listed and I chose it to start up. Does anyone have the answers. I worked on this for 2 days and I am at my wits end at this point. I even recorded files from the drive to a flash drive, but that doesn't work anymore. Help.

  [edited for clarity]

  You can check if the new HARD drive is listed on BIOS SATA devices?

  Press F2 at startup.

  I don't think that the size will be a problem but you need to check if the HARD disk is read by the BIOS.

• Windows Live Photo Gallery causes the error Code: 0 x 80010108

  I have a desktop XPS 8500 running Windows 7.  Love it except for one thing: Windows Live Photo Gallery causes the error Code: 0 x 80010108.  Yes, I x it down and go ahead and use my computer but like it to stop.  I have google code and there are a number of fixes called there for him - even though they claim.  But I was reluctant to download anything on sites I don't necessarily trust OR conform to change my registry to fix it.  Can someone recommend a cure to my problem?  I have confidence in this forum for more than 12 years and feel that you will not recommend something that might get me in trouble.

  Thank you

  Bessie

  Hi Bessie,

  Thanks for the reply. I suggest you to uninstall Windows Live Essentials from the computer and update to the latest version. You can download it from the link http://bit.ly/GQ9tPI . Please disconnect all the external devices connected to the computer (printers, external hard drives, flash drives) and do not have any CD/DVD in the drive while following the steps.

  Answer please if you have any questions.

• I would like some clarification on what is causing the error code 80040154

  It seems to crop in Live Essentials update on a regular basis, but I can't find all the details on the causes

  Additional information.
  I managed to get the Messenger to sign. Here's info on how although I \have no idea why this worked. I tried a new install with the same old results but happened to see a link to messenger and connect to web services. It took me to a page of Microsoft, and the best I can see is that he installed connections on social, utube, facebook and twitter sites, etc.. I make no use of these sites once he installed my Messenger came, I signed the as if nothing had ever been wrong. I have now idea why, but be it - it works.
  I would like to really know what causes the error code 80040154 for possible future needs.

  Please see the thread below for a possible answer:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_programs/Windows-7-and-Windows-Live-Messenger-error-code/93f4d2e5-24ed-40c3-957d-a0ab9f53dac6