New hardware, BSOD! Help!

Similar Questions

• Cannot install new hardware (wireless mouse, ipod) on my Equium M50

  Hello

  I'm a newbie here, I m having problems with my Equium M50-192 don't know when the problem started, but I can not install new hardware have tried to install a wireless mouse and a new ipod, but it will not install the drivers for the latter.

  Any help will be appreciated.

  I don't really know what the problem is here, but it will be interesting to know what exactly happens when you connect a wireless mouse. Is there a HARD drive activity or even error message?

  Can you please check the Device Manager and hardware all listed there? Is this all is well?

• Satellite L500-19F: where can I get new hardware components

  Hello, sorry for my English, I am from the Germany.

  My notebook Satellite L500-19 is defect.
  Next few days I'll be watching, that things are missing...

  I think that its first of all the motherboard.

  Now my question: where can I get new hardware components for my laptop?
  Where I have to 'click' on the Web from Toshiba site?

  Thanks for the help!

  Hello

  All parts can be ordered from an ASP from Toshiba (certified partner) in your country.

  You will find here all the FSA all over the world:

  * http://eu.computers.toshiba-europe.com-> Support downloads &-> find an authorized Service provider *.

  Welcome them

• Satellite L500-1XL - new hardware upgrades

  Hi all
  I have the Toshiba Satellite L500-1XL and recently bought a new 500 GB internal HD and the upgrade went well. However, the internal transfer speeds aren't that fast. He is often out on 18mps level. Why? Affects of that? Use of the RAM, the use of the disk, the free storage space? The HD came with the laptop was 5400 with 8 MB, but my new is 7200 RPM with 16 MB with 11 seconds of access time. If that should not be much faster?

  Also, how can we get the support of USB 3.0? Only through new hardware? I know it goes into Windows 8 as this means there could be a few Windows 7 supports or who is still dependent on material?

  What are the most effective upgrade options to make my laptop run faster? He was modest. When I got it, but now use it for any need so get. Thus, upgrading to HD 160 GB to 500 GB (5400-7200), but it's unique processor with only 2 GB of RAM. I noticed on the Toshiba page so it says on a 64 bit system with 4 GB of RAM, the chart may use up to 1 800 MB of RAM upgrade RAM (not expensive) and then the processor? Even a single dual core would do the job? No need for a costly i3 and perhaps not compatible with the motherboard.

  Thank you!

  Hey Buddy,

  And what was your old HDD? HARD disk speed depends on different factors. You copy a large number of small files and a large single file?
  It s also useful to defragment the HARD drive from time to time. This can improve the speed. Also keep the system clean and use a registry cleaner like CCleaner that cleans up your registry.

  USB3.0 is a different interface. This new operating system wouldn t help you because it s material new feature/upgrade.

  Other improvements regarding: CPU and graphics card is not supported as you can read here:
  http://APS2.toshiba-tro.de/KB0/FAQ35006D000RR01.htm

  Your laptop has Intel GL40 chipset and the maximum RAM capacity is 4 GB. So you can install 2 GB DDR2-667 module in each memory location.

• Found New Hardware Wizard initiate at startup with no new hardware installed

  Hi Xircal,

  Thanks for your interest.

  The Malwarebytes we were a beta with a lot of precautions.

  I ran the Sophos base scan on C:.
  Nothing that you marked for deletion.
  Just hundreds of hidden files, mostly in the Recovery Console XP (minint), the RRBackups, the preboot\helps, the two Norton .dat files: cltLMS1.dat & cltLMS2.dat

  Description: Unknown hidden file
  Removable: Yes (but clean not recommended for this file)

  Norton said: «these files are components licenses of Norton.» Legitimate files of Norton. (They are not paid for spelling)

  I could run a scan in depth tonight if you think necessary.
  I have a bunch of drives on this computer, but c is the one who starts.
  In fact, I have a separate drive that I use to download software executables, drivers, etc..

  Peggy

  Hi Peggy,

  Does not sound like there is nothing to worry about here.

  The 'new hardware found' is still running at startup?

  Also, could you possibly get in touch with Norton and ask them if ROOT\LEGACY_BEEP\XX_NPF_XX in Device Manager has nothing to do with the Norton Personal Firewall? It could be something as simple as that.

  I think you're right. I don't see anything unusual but one long-standing issue date with Norton Security turned off randomly on startup (I does not start unless I'm free to control and turn it on if it is off)

  I contacted Norton on that months ago and they were not able to solve it, but strongly advised I have remove a bunch of utility programs that they don't like. Split us up on this suggestion. I have uninstall Super Anti-Spyware, and you know the rest of this story. But I think Secunia PSI, Winpatrol, AutoCAD, etc. as essential to my well-being computer.

  I think I'll let the dog Norton are.

  The 'new hardware found' has NOT yet run at startup. Thank you very much.

  Assume that you have done at least what I asked you to do. I'll miss our daily interactions, but you'd better take your white hat to someone who needs your expertise more than me.

  Peggy

• Found new hardware unknown wizard

  I have a Windows XP Media Center Edition computer. A few days ago, he jumped to the top of the box, "Welcome to the new hardware detected" whenever I turn on my computer. I don't know why and I think that he doesn't even know why, because he said, "this wizard helps you install software for: unknown." When I try to install the software automatically (recommended) it continues to show that it is looking for unknown. I have not plugged my hard drive backup from another computer, which usually makes it to do. I tried to do a restore of the system at the beginning of the week (today is 10/01/13) and it still does not work. Then I did a system restore to last Thursday and it still does not work. Why my computer do that?

  Hello

  Yes, now you must contact HP support.

  Thank you!

• The new hardware wizard finds

  I have a Western Digital external backup drive. I get the wizard Found new hardware message whenever I start the system. The salesman says this means that the operating system does not have drivers for my device on the record, they made a correct installation of the devices, but it does not keep the computer, they suggest that there could be a problem with the operating system. Can you help me?

  Good to hear it worked for you... Please mark this answer to the debate...

• Add Wizard hardware detects new hardware when I don't have any new material

  Recently and all of a sudden, the Hardware Wizard detects new hardware.  I don't have all new equipment installed. What is the solution?

  Hello

  1. have you made changes on the computer before this problem?
  2. check what hardware wizard detects new, printer, USB... ?

  I suggest you follow the Microsoft article and check if it helps.

  The new hardware wizard may detect the printer device after every restart of the computer: http://support.microsoft.com/kb/298370

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://support.microsoft.com/kb/322756

  See also:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-hardware/found-new-hardware-wizard/970f411a-7848-E011-8dfc-68b599b31bf5

  http://support.Microsoft.com/kb/323511

• Annoying popup of the new hardware wizard

  Just upgraded my virus to a newer program.  During the instalation, have uninstalled all unnecessary programs free spyware I had on my computer.

  When I start it, a "new hardware found" window immediately.

  Why is this and how can I stop, as he reports is "unknown"?

  Hello
  I suggest you to follow these steps and check if that helps:
  Method 1:
  Start the computer in safe mode and check if the same problem occurs:
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/boot_failsafe.mspx?mfr=true

  Method 2:
  Try to perform the clean boot and check if it helps:
  http://support.Microsoft.com/kb/310353

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• New hardware found Message keeps appearing.

  I have an installation of the professional XP SP3, I have installed a Canon MP970 printer via the USB port.  Whenever the PC is started, the dialog "new hardware found" rises and guests come to the 'NEW' printer, I used the disks provided with the printer, the download of Canon files and still continue to get the same message every time the machine is started. That is what it is?

  XP SP3

  Phenom Quad Core

  This printer has been previously installed on Dell Dimension 8250 with no problems.

  Tom,
  This printer is 'all IN one' type IE you have install the driver for scanner and printer. so update appropriate for the printer driver you. Here the link to download: http://www.siliconguide.com/drivers/device/1275/
  Hope this will help you
  Kind regards
  Chauvet J.

• During the installation of a wireless mouse, the 'New Hardware Wizard' appears unnecessarily!

  During the installation of a wireless mouse, the "New Hardware Wizard" pops up, and more than a half a dozen times looking for the pilot.  I installed the driver from the disk provided by the manufacturer.  Actually, the mouse works correctly and doesn't have another driver not found.  Someone has suggestions for the "new hardware found" stop?

  Hardware devices do not work or are not detected in Windows

  Does that help?

• Found New Hardware Wizard will not let me install things.

  Hello.
  I have Windows XP and every time I try to plug something for the 1st time, such as a USB, a window that reads the found new hardware wizard appears. He asks me if windows update can search for new software. It gives me so "Yes, always", "Yes just for this" or "no, not this time". No matter that we I press, another window appears which says ' if it came with an installation cd put in now "then gives me the options either"install the software automatically or manually." When I press the other, she begins searching and, after a minute or two, a window appears saying that the software had failed the compatibility test, even when I got from devices that say they are compatible with windows xp. Then it gives me the option to stop or to continue. No matter what I press, the Hardware Wizard says there is an error and closes. Subsequently, it will not recognize the USB and I have to uninstall it.  This also occurs when you try to install things like itunes.
  Someone help me please. I have not tried it on other computers because I have no one else at my disposal. I tried to contact the company USB but I was told that it's a computer, not a jumpdrive, question.

  Thank you for your help.

  Try the steps in the below given Web site

  http://www.technipages.com/disable-has-not-passed-Windows-logo-testing-message.html

• popup "Found New Hardware MTP Device"

  I have a pop-up "Found new hardware device MTP" constantly to come. I can't get rid of even try go to control panel > Menu start & task bar but can't find it. Can anyone help?

  You have an MP3 of some sort?

  Maybe you've seen this?
  http://forums.CNET.com/7723-7595_102-229230.html

  My advice - however - is to get the latest software and drivers for whatever the device originally this message pop up.  Like I implied--probably an MP3 player.

• Windows XP prevents me from installing the new hardware as my Canon camera and memory card reader.

  original title: problem with new hardware

  last week, windows xp prevented me from installing new hardware, namely a canon digital camera and a memory card reader. Although the system recognizes the material into the machine, when you are looking for auto install it asks me for the service pack 3 cd, which I did not. I never had problems, install new hardware before. Any ideas why this happens?

  Hello

  · What is the service pack installed on the computer?

  · What is the model number of the canon camera?

  · What is the exact error message that you receive with error code if any?

  If you have installed service pack 3 on the computer then you can try the method and check them off below if it helps:

  Change the registry to point to the installation of Windows XP Service Pack 3 files

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: How do I back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

  a. Click Start, click Run, type regedit in the Open box and then click OK.

  b. find the following registry key:

  c. HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Setup

  d. in the right pane, right-click ServicePackSourcePath, click on edit, type % windir%\ServicePackFiles, and then click OK.

• How to stop "FOUND NEW HARDWARE tool"

  Whenever I start up I get the message "FOUND NEW HARDWARE TOOL' up to four 4 times before so I can continue."  How in the heck to I get rid of this.  It is also irritating as my HP printer messages all the time!  LEA

  Hi LEA J.HIGGINS,.

  ·          Did you the latest changes on the computer?

  See the below Microsoft article and try the steps mentioned, check if it helps.

  The new hardware wizard may detect the printer device after every restart of the computer

  http://support.Microsoft.com/kb/298370

  If the previous step fails, then check in the Device Manager to see if a device does not work or pilot device tries to install at the start.

  How to troubleshoot unknown devices listed in Device Manager in Windows XP

  http://support.Microsoft.com/kb/314464