New router BEFSR41 problems installing...

Similar Questions

• New router connection problems

  So I just got a new router delivered to my cause of House, that we had to move to a new location, and that we have obtained will not let me connect to the internet via a modem-> router-> computer.  It works very well when connecting with the computer of my brother through wireless. When wired to the router I get full connected via the internet and so on, but when it comes to my computer wireless router, do not let me go beyond "local only". He remains as unidentified network and can't get more than that.  Ive tried to restore my computer to Service Pack 1 and remove Norton from my computer with the removal tool and nothing seems to work. Ive changed my setting of the router mode 50MBPS and stuff and nothing, defining the network IP and DNS in my Protocol which is in my router and that did not work either, my IP address restarts and refreshing, nope. Im running Windows Vista Home Basic with an Atheros AR5007 802 network card. 11b / g. router Netgear WNR1000v2.  I had a problem with my computer with my last router.

  It's my connection information:

  Microsoft Windows [Version 6.0.6001]

  Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

  
  

  C:\Users\***>ipconfig/all

  
  

  Windows IP configuration

  
  

  Name of the host...: *-PC

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  
  

  Wireless network connection Wireless LAN adapter:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-24-2B-C8-1A-21

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  
  

  Ethernet connection to the Local network card:

  
  

  The connection-specific DNS suffix. :

  Description...: Realtek RTL8102E Family PCI - E Fast Ethern

  and NIC (NDIS 6.0)

  Physical address.... : 00-1F-16-70-E0-A5

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::a85c:6ec9:2 has 4: bbf5% 10 (Preferred)

  IPv4 address: 192.168.1.4 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Monday, November 29, 2010 14:29:05

  End of the lease...: Tuesday, November 30, 2010 14:29:05

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  
  

  Card tunnel Local Area Connection * 6:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {E418D763-0DB4-4DCA - B 9, 70 - E94D132E8}

  62 A}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  
  

  Card tunnel Local Area Connection * 7:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {F2AFB4E5-A1E8 - 415 B-A7B3-A433B3227}

  715}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  
  

  Card tunnel Local Area Connection * 11:

  
  

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

   

  Any help would be appreciated.

  
  

  Well, I tried everything you listed on here and nothing seemed to work. I found a good solution to change my WEP security and he recognized her. Looks like it has problems with the other encryption security. Thanks for your help though!

• CP1525nw: new router: cp1525nw wifi install fails with the vague error message

  Product: HP Laserjet Pro cp1525nw

  OS: WIndows 8.1

  Hardware: Computer Asus laptop

  Recently received new router from Verizon (FIOS), model FQG1100 BHR4 router

  Purchase printer in 2012.

  Printer has worked with the old router; It will not communicate with the new router.

  For four days I deleted the printer from the laptop several times and tried to reinstall using the wifi. Installation instructions say to run the CD, select wifi, connect the USB cable when prompted, configure, remove the cable when prompted.

  When I attach the USB cable, Setup starts, but it expires ("taking too long") or fails with the vague message about not finding the product. I'm never invited to an SSID.

  I tried a USB installation and it worked; If the USB cable is good.

  Share print files & Windows is activated.

  I tried to re - adjust the printer by default and insured menu wifi said 'ON' for the wifi.

  I run a wireless network test report:

  SWITCH for wireless, wireless and security.

  Failure of network name (SSID found).

  DO NOT RUN for: printer settings consistent with the settings of the wireless router, no filtering, connected, the signal strength, other networks detected.

  Wireless netwrorks detected: 9

  I note the router label does not say "SSID", but said "ESSID".

  I have ideas for what to try.

  Please post here or send message to [personal information deleted]

  Last night I finally got to work.  I removed the printer entirely from the PC and rebooted. I turned off the printer. I ran a cable to the router (cable modem). I have reset the router, which then assigned an IP address to the printer. I changed the security settings on the router to use WEP instead of WPA. I ran the HP printer, Setup - and he finally presented me with the screen to "provide the SSID.  The program is run properly. I printed a test page. I changed the router security to WPA2. I printed a test page.     I tried to restart it and reprinted.  I also tried to remove the cable and then print again - printing failed.

  In short, I needed to do two things: connect a cable and change the router temporarily WEP for installation.

  In my case, my printer is close enough to the router with the cable.  A bit disappointing that the true wireless will not work, but I can print wireless from my laptop.

  I saw how many people have had the same problem, I had, and how much of HP is of any help to solve this problem.  I am convinced that the printer has a defect.  I hope that my posts will be useful to a few people having the same problem.

• HP Officejet 4500 all-in-one: do not print after a new router has been installed

  I recently got a router update Verizon Wireless. I updated the password key on my devices and also assured that the printer is visible from my PC. However since the upgrade, I can't anything to print.

  I tried whole process of turning off the printer and the router and the password rentering. The PC recogize the printer but there may some disconnect somewhere that I can't make impression - help...

  Thank you!

  Replacement/change your wireless router try here.

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

• OfficeJet 6600 e-all-in-one: Wireless connectivity with the new router problem

  We had the printer since 12 months, workin with no problems.

  Just got a new modem/router (NETGEAR V7610) installed as part of the NBN implementation and I can't get the printer to connect to the new router. 5 and 2.4 G active networks. The two defined newtorks on security WPA2-PSK [AES].

  The printer detects the wireless (2. 4 g) network, but can't coplete the connection. Tried the two direct input the network key and using WMA.

  -The display panel shows "wireless invalid password (WPA) is entered.

  -The results of network printer test page indicates a FAILURE on safety.

  I was able to connect to multiple other devices (laptop, iphone, Kindle...) without any problem. Used the two direct entry of the key network and WMA.

  Anything else I can try?

  Find a new update of the firmware for the printer (May 9, 2016).

  After you apply the update, the printer is able to connect to the new modem.

• I GOT A NEW ROUTER FROM VERIZON ACTIONTEC GT784 INSTALLED BUT NOW CAN'T USE MY MX340 WIRELESS PRINTER HELP

  I GOT A NEW ROUTER FROM VERIZON ACTIONTEC GT784 INSTALLED BUT NOW MY PRINTER DOES NOT PRINT. MX340 WIRELESS PRINTER. CLOSE

  Hello

  To help you to propose measures to solve the problem, I would appreciate if you could answer the following question:

  1. what version of Windows operating system is installed on the computer?

  2 successful wireless connection configuration?

  3. do you receive an error message or error code when trying to print?

  In the meantime, I suggest to add the device on the network and check if that does the trick. To do this, follow these items:

  Connect to Bluetooth and other wireless or network devices

  http://Windows.Microsoft.com/en-us/Windows7/connect-to-Bluetooth-and-other-wireless-or-network-devices

   

  Add a device or computer to a network

  http://Windows.Microsoft.com/en-us/Windows7/add-a-device-or-computer-to-a-network

   

  Sharing of files and printers

  http://Windows.Microsoft.com/en-us/Windows/sharing-files-printers-help#sharing-files-and-printers=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information helps. Reply with more information about the issue so that we can help you better.

• I just installed a new router and now my desktop running Windows XP computer does not connect to the internet.

  Hello

  I just installed a new router and now my desktop running xp computer does not connect to the internet. I know that it is not the router because I plugged the cable into my laptop running 7 and it works fine. When I try to dhcp I get 169..., when I put manually the IP just get no access to the internet and can not ping to the router address. I tried to run the net work Assistant, emptied my dns, disabled all firewals, still nothing.
  Any suggestions?
  original title: connectivity Limeted

  The zero configuration utility works very well. But it is a desktop computer and on cable. All other wired and wireless PC in the office is working well, then it's definitely this PC. He came out of nowhere, I install a network printer on the PC but that's all.

  Your messages are a bit terse, but if I understand correctly

  • You have a router connected to the Internet and multiple computers connected to the router, some Ethernet cable and others by wireless.
  • All but one of these computers can reach successfully from the Internet via the router.
  • A computer that can't browse the Internet is connected to the router via an Ethernet cable.
  • You disconnected the cable between the router and the desktop problem and connected it to a Windows 7 laptop and the laptop connected to the Internet via the router.
  • You haven't seen any error message (except, perhaps, a message on "Limited or no connectivity").
  • You have installed Windows XP Service Pack 3 (or at least Service Pack 2)

  Assuming that all the foregoing is an accurate summary of the situation, I suggest that you do the following:

  Open a command prompt window (start > run > cmd > OK)
  Type the following lines and press ENTER after each line

  Netsh reset winsock catalog
  netsh int ip reset c:\resetlog.txt

  Close the command prompt window and restart the computer.

• Could get a new router block printing? We had a lot of problems with the computer in the last week and a half. Bought new router and now the printer does not print. :-(

  (1) we went to DirecTV. Then the same day, our internet computer is down. I asked our current provider, Suddenlink, to let them know we had them to another - but we wanted to keep for the internet.

  (2) called DirecTV to investigate why our internet went down at the same time they installed? They said that they did nothing to cause that. We waited 5 days to make out and also install the third TV that was promised. The second tech gave things a lookover and said, once again, that there is nothing unusual during their passage to cause the problem.

  (3) called Suddenlink. They said it was the router. Called the people of Netgear. They said that the router was too old. We needed to pay an exorbitant sum for support and when I told him I'd rather just buy a new router and get free technical support for 90 days... and I personally do not have the credit cards in that time. (it's my mother s equip and I wonder it for the computer) when the guy told me that he could help and hung up on us, even though I was pleading for him to wait until I put my mother on the phone. (I'm in my 40s... not a kid).

  (4) Suddenlink called a few days later, when we got a new router (netgear brand NO!) Installed and I noticed that the 'ready' light was not 'on' on the modem. Their technology has said that he would check and call us in a few minutes. He did not.

  (5) the next day I called Suddenlink AGAIN. This time, I got a really nice customer service agent. She said she would send someone to check on it. It turns out that they had disconnected when I had called to pass only the TV.

  (6) in any case, we are finally online... only now... I can't the printer to work. :-(  This has worked before.  Could it be caused by the different router? I don't know about these things. I didn't even know what it was until someone at Radio Shack has explained to me. (I was not about to buy one at Wal-Mart - these poor people). The printer is a Canon Pixma MX340. We love him. The only thing is that it is difficult to clear the tasks or to reset. The only way to really do that is to simply pull the plug, unfortunately and restart the computer. But hey, it's a great printer, better than HP.

  We are under vista. The router is a Linksys wifi (which we have) N300 model E900.

  Of course I appreciate any help you can give. God bless you!

  Michelle and Ruth.

  Hello

  Thanks for posting in the Microsoft Community.

  I understand that you are facing problems with the printer in Windows Vista.

  I imagine the inconvenience that you are experiencing. I will definitely help you with this.

  Please follow the steps in the link.

  Solve printer problems

  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

• I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet.

  Connected to the new router, but locally only.

  Currently, I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet. The small icon to the left of my screen says only: ACCESS: LOCAL ONLY.
  BASICALLY,.

  I have Windows Vista Home Premium, notebook Compaq (Presario CQ60 to be exact)

  I can connect if I use a cable, but its disadvantages.

  I can connect wirelessly with my PC and Ipad. and Internet access.

  I TRIED:
  Various patches microsoft such as resetting TCP, safe mode with network, reset the router. »

  Thank you in advance and we hope you can answer this soon!

  I use an Atheros AR5007 802. 11 b / g WiFi Adapter(Compaq laptop) for the moment so this is useful. Thanks again!
  Someone suggested that I update my wireless driver. I am open to this idea, if anyone can find a safe and legal site with the download.

  Hi Bryyaan11,

  You can check out the link to HP support and try to download the drivers for your wireless card updated:

  Support HP & drivers

  For more information, you can also consult the following article:

  Updated a hardware driver that is not working properly

  You can also check the following items and try the steps:

  Windows wireless and wired network connection problems

  Solve problems, find wireless networks

  Hope this information is useful.

• Installed new router

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Just got a new Netgear N300 wireless router.   We have two Imac an Acer netbook, and the daughter has a Dell PC with Vista.  His computer will not hook up with the new router.   Other computers have made this automatic.  She won't.  Any suggestions?

  I used XP for years and know how it works, but don't know about Vista.

  Maybe this can help
  

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Apple 3rd generation does not after having installed new router put I in the codes manually

  Hi recently had outages etc and a new installed router in wifi but now my apple tv 3 does not work but only home screen sharing/settings see I am signed the Mac for home sharing.  When I go into network settings I see the configuration is automatic, but the router shows that n/a, does that mean that I have to put codes?

  TIA

  Wendy

  You have connected the Apple TV for the new router?  You will need to make sure that the Apple TV is connected to the wifi network, which broadcasts the new router...

  Get help with Wi - Fi on your Apple TV networks - Apple Support

• Installed new router wireless; don't know how to change the settings of the printer

  I just changed the wireless router that has created a problem with printing. I don't know what I have to do to change the printer settings to accommodate the new wireless router. Would be very happy for any help with how to do it. I'm on Windows XP SP3 with a HP all-in-one on a wireless laptop (no wired connection). Wireless router is a linksys. Free trial security AVG 8. Thank you!

  @jerrymcampbell, sorry you had a problem given that you got a new router.

  You will just need to reconnect the printer to the network again.

  What kind of printer you have?

  Function of the printer, you can access the network settings on the printer, choose the Setup wireless and connect to the new network wizard.

  After that, go to the computer and to update the IP address.

  1. click on Start Menu

  2. Select all programs

  3 select the HP folder

  4. click on the name of the printer

  5 scroll to the IP ADDRESS UPDATE

• Time Capsule missing after installing new router

  I recently installed a new wifi router for my home network. Previously, I used only my time capsule to back up data and intend to continue to use it for backups. However, with my new router, I can't find how to access the time capsule to keep backups. I have time capsule directly connected to the router via ethernet and it will still not appear in AirPort Utility or enable Time Machine to find.

  Any suggestions?

  Everything has changed.

  With a new router, you have a 'new' network... and the time Capsule is to remember the parameters which it was equipped to work in your 'old' network The time Capsule is lost and he can't find his way.

  Reset to return to the default settings Time Capsule

  Connect it to the router

  Set up the time again to work with the "new" network Capsule

• How to install a new router?

  original title: new installation of router

  When you install a new router you let your internet provider know before disconnecting the old man a moment I left the old one hanging don't know what to do

  What do you use to connect to your ISP, cable modem, DSL, modem?

  If you use a cable modem that is separate from the router, then all you should have to do is connect the router to the cable modem, then connect your PC to the router, either UTP or wireless. Your PC should then take a new IP address of the router, and you'll be good to go :-)
  --
  SC Tom

• Problem installing LAN USB adapter in a new copy of windows 2000

  After having reformatted my hard drive and install a new copy of window 2000, I'm having a problem installing device drivers.  When I enter the correct inf file path, it reports that this window has not found a driver for the device.  Whithout the possibility to connect to internet, I have exhausted all my options and still need to install several other drivers with the same problem.  help help help help

  Everything you try to use (you do not give the brand / model of the LAN USB adapter) made drivers for Windows 2000?