new router to work 1245dx dv5

Similar Questions

• AirPlay does not work on new router

  Hello world

  I read so many topics here on airplay, but I am absolutely tired of trying everything without any results at all. So I hope that someone will know the answer.

  So. My amp is connected via an eithernet cable to a router. Amplifier a airplay in there and able to play the music of apple devices. I used to play music from my iPhone. My router is a generic router from BT, I think that the 3rd generation. This Setup has worked well without any adjustment, straight out of the box,

  Recently, I switched to another internet provider - Relish, is a London based provider internet 4G. Their router is manufactured by Gemtek. The configuration of the router is the same as BT (at least to the extent that I noticed) however my Airplay has stopped working.

  • I tried all the shamanic standard moves, like any change and turn on etc.
  • I also tried to rewire everything back to BT router and it worked. So it's certainly something in the router, but I don't understand that. Also.
  • The amplifier has a mobile application for use as a remote control. The application connects to the amplifier by the same router OK, can I turn on or off etc. If the connection is OK.

  I look forward to your suggestions!

  Many thanks in advance,

  Alex

  Here are the ports that airplay depends on... (search for airtime in the list)

  TCP and UDP ports used by Apple software - Support Apple products

  He'd have (pardon the pun) that your new router can have these locked in its default configuration.

• Satellite L40-143 - WLAN does not work with the new router

  WLAN on my Satellite L40-143 does not work since I Modem Alice-1121.

  Who can help me, please!

  Hi kenny_21,

  If you have a new WLAN router you must change the configuration that I think

  The new router is visible under WLAN connections and can connect?

  If so try to connect. The standard router password can be found in the manual of it and no doubt, there will be new addresses MAC first before connect you. I put t know the exact configuration.

  Also check the options the WIRELESS card with TCP/IP. Usually, you need automatic IP addresses.

• new router, printer now Wireless does not work.

  We had trouble getting online.  ISP determined it was our router.  Bought and installed new router.  Internet access children laptops and thin, but now HP photosmart Plus B209 sees no new router.  Tried to Setup Wizard, no luck, tried to push button and PIN the installation program from the front of the printer, no luck. Tried to network settings in the box tools in the HP software on my computer, but said that it was impossible to recover the input parameters.  The printer was working fine with the old router.  Report of test of the printer still displays the old "SSID network name so, of course, this isn't the link to the new router."  Help!  don't know what else to do.

  You don't need to buy anything to install this printer.

  Do NOT use a CD for the software (ever, if you can help it).  Download and install the latest version of the software for your printer from the "Support & drivers" link at the top of this page.

• I have a new router and the printer does not work. I have the hp photosmart c4795 all-in-one.

  What should I do to get the router to recognize the new router

  It's working now. I deleted my printer, downloaded the software from HP and added the new printer. Followed the instructions and it is running. Thank you

• Vista 32 bit does not connect to internet via wifi on new router. All other computers work.

  I upgraded my router Belkin G to a Netgear N150.  My computer laptop windows 7, ipad and ps3 to connect to the internet.  My Vista laptop will connect via cable but not wireless.  The wireless still works on the old router.  The new router DHCP assigns an ip address from my laptop to visa, but it's a unidentified network which is local only.

  I tried to reset the tcp/ip and winsock stack.
  I disabled wireless utility from Toshiba configFree.
  I ran:
  ARP d
  ping 192.168.1.1
  Ping 192.168.1.1 with 32 bytes of data:
  Response of 192.168.1.15: Destination unreachable host.
  Response of 192.168.1.15: Destination unreachable host.
  Request timed out.
  Response of 192.168.1.15: Destination unreachable host.
  Ping statistics for 192.168.1.1:
  Packets: Sent = 4, received = 3, Lost = 1 (25% loss),
  ARP - a - v:
  Interface: 192.168.1.15 - 0xb
  Internet address physical address type
  192.168.1.1 00-00-00-00-00-00 Invalid
  ipconfig/all /allcompartments

  Windows IP configuration

  ==============================================================================

  Information network for the compartment 1 (ACTIVE)

  ==============================================================================

  Name of the host...: jennifer-PC

  Primary Dns suffix...:

  Node... type: mixed

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007EG Wireless Network adapt

  Physical address.... : 00-24-D2-8B-4F-ED

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::6476:106d:3c70:4bf3% 11 (Preferred)

  IPv4 address: 192.168.1.15 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Thursday, February 16, 2012 20:11:05

  End of the lease...: Friday 17 February 2012 20:11:04

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DHCPv6 IOOKING...: 285222098

  DHCPv6 DUID customer...: 00-01-00-01-13-87-1B-E5-00-1E-33-80-70-41

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Description...: Realtek RTL8102E Family PCI - E Fast Ethern

  and NIC (NDIS 6.0)

  Physical address.... : 00-1E-33-80-70-41

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Description...
  . : isatap. {0E605CFB-74AF - 441-A-8404-DC7C2175F
  9 9}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 17:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {0E605CFB-74AF - 441-A-8404-DC7C2175F
  9 9}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...
  . : Yes
  Card tunnel Local Area Connection * 18:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {BCF6118F-5DAA-4C0C-BEBD-710E18983
  E72}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 19:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {0E605CFB-74AF - 441-A-8404-DC7C2175F
  9 9}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 21:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {0E605CFB-74AF - 441-A-8404-DC7C2175F
  9 9}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  I can't think of anything to try.  I really want to go back to my other router.  Any help would be appreciated.

  Solved.  Was a driver problem with Atheros adapter Vista security and network.  Downloaded new driver and Voila.

• New router now the printer will not work wireless

  The printer is a HP1102W. Operating system is windows 7. At & t installed a new router is a netgear 7550. I tried several times to get the printer to work wireless but just cannot make it work. Not very food to computers so I could really use some help.

  Thank you

  Hello

  Please follow the instructions below to fix:

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

  Kind regards.

• P1102w printer: have new router and can not figure out how to print wireless at P1102w printer - he sees old router

  I installed a new router (Netgear R6220) and cannot figure out how to get the P1102w printer to recognize the new router. It shows the former name of the router (Belkin.833) on the test page and displays the IP address configured by AutoIP rather than DHCP as the old router does. The computer is a desktop Dell Dimenstion about 3 years and use Windows 7. The router connects to the computer to the Internet.

  Help - How to make the printer recognize and communicate with the new router? (The original installation instructions don't seem to work for me.)

  I made an update of the firmware a few months ago and the currtent datecode is 20130703. Allowed to print from my Samsung S2 Tablet through the router.

  Here's what finally worked.

  1 had to withdraw from old installation CD but Uninstall selected, so I completely shut down the computer. Guy at Best Buy said to "remove the device" but it was not enough.

  2. download install the latest software from the HP download site and ran it. (http://ftp.hp.com/pub/softlib/software13/COL32431/bi-80329-11/hp_LJP1100_P1560_P1600_Full_Solution-v20120831-50157036_SMO.exe)

  3 downloaded another file and ran it. (Setup_IP4, [192_168_1_5], [NPI073E2D] _it) Not sure where I found this one, but the software prompted me to run.

  Finally, everything works and all devices are wireless printing

• Apple 3rd generation does not after having installed new router put I in the codes manually

  Hi recently had outages etc and a new installed router in wifi but now my apple tv 3 does not work but only home screen sharing/settings see I am signed the Mac for home sharing.  When I go into network settings I see the configuration is automatic, but the router shows that n/a, does that mean that I have to put codes?

  TIA

  Wendy

  You have connected the Apple TV for the new router?  You will need to make sure that the Apple TV is connected to the wifi network, which broadcasts the new router...

  Get help with Wi - Fi on your Apple TV networks - Apple Support

• added a new router

  Hello

  I use my Time Capsule for 4 or 5 years now and it has worked pretty well. Yesterday, I swapped a modem provided by my company and I also got a new router from them (Sagemcom Fast 3260cv). I put everything in place with the new modem and the router. I am using their channel 5G. Time Machine couldn't find the backup disk until I plugged the Capsule on the router. The flashing yellow light went green and I could make backups.

  My question is, are there downsides to do things this way? As far as I know, I use the 5G for all my internet activity and the connection network wireless to my Time Capsule for my backups. This seems to be ideal. Now, I won't have to worry about backups on my internet bandwidth, although I suppose that the bandwidth of the MacBook Pro to the time Capsule will take a piece out of it, or will it? I guess the Time Capsule will not need to access the internet and instead just start over and set up to be only a backup unit, Time Capsule by plugging right on the router I can make it work.

  I read a little about changing the Time Capsule in Bridge mode. Requiring from anywhere in my backups?

  Is it a problem to have two networks in the House? The new router and the Capsule are right next to each other. (To be honest, I'm a little worried by the router sitting on top of the time Capsule that time Capsule remains warm enough. So, I even a plate isolating (a real plate) below electronics below are not affected by the heat.

  In addition, the cable operator said that the open network providing their router will not affect my bandwidth and that anyone using it (I see 17 networks using iStumbler, most have no signal strength, but some are equal to mine. (Mine readings 77% for 5 G and it is about 8 feet away and online direct from my MacBook Pro...) In any case, I guess it's ok to have the open network. I asked l ' switch off, but they say I can't do that. I do not need it...

  Thus, a lot of questions.

  Thanks for any help.

  See you soon,.

  John L

  I read a little about changing the Time Capsule in Bridge mode. Requiring from anywhere in my backups?

  You have a lot of questions, scattered through... I'll answer has some time and come back.

  You must never start backups due to the configuration of TC... Although you may lose the connection to the backup and the need to reconnect... which is sometimes delicate. TM will say that he will start a new backup and then discover the existing one.

  Changes on behalf of transport CANADA will TM to lose the connection but should reconnect for backups.

  A change of name of the computer will TM now start a new backup. (Although this is not 100%).

  I'm a bit worried by the router sitting on top of the time Capsule that time Capsule remains warm enough.

  Never stack network routers...

  Separate them by about 1 M.

  Train wireless or heat problems.

  There is nothing wrong with the execution of multiple wireless networks... There is a big problem, stack one on top of the other wireless routers.

  The best idea is to run ethernet to a room where you need more wireless and locate the TC it.

  In addition, the cable operator said that the open network providing their router will not affect my bandwidth

  It is bulldust ISP... I will come back more... Anon.

• New router ' Fritz! Box "7490, reconfiguration of network"

  I just upgraded my router, Fritz! Box 7490, & I need to re-set my network help please.

  Before the upgrade, I had a very old router Aolynk. This was connected to my TC, the last giving us WiFi for our House, but also my parents House, via an Ethernet cable connecting the TC at the airport Exremem BS. Beside that, I use the TC to occasionally save the iMac & the RMBR & the old router sent our CCTV to phones via an Ethernet cable. The new router is now the primary device & our hub WiFi (Wireless AC active). I read an article that I thought would help, but I had no success.

  I need assistance with the above, and some tips on how to host 6 other our audio/video system Ethernet cables (two rooms, each show 3 cables, one for the Smart TV, APR or other devices requiring an update and media coils).

  I want it is-

  1. to put WiFi on my parents. After reading the article, I followed the instructions, linking the TC with my iMac, turn off the "WiFi" on the TC & activation of Bridge mode. I got the TC & tried to thread failed. Run the cable to the Lan port of the router to the WLAN or a LAN on the TC port? I want to use the TC in this way, so I can release the LAN ports of the router, which I have 3 (Gigabit). The 4th is used for the Internet. I then connect an Ethernet cable between a LAN on the TC to the BS port extreme airport as before. I have to configure EI?

  2. I want the Ethernet of CCTV cable through the TC rather than use one of the ports on the router, which is the situation at present. (Of course I don't want another outgoing cable TC goes to the router as it defeats the purpose to release the ports on the router.) I wanted to lift as soon as possible the line & it was the fastest way. We had trouble getting food for the mobile, but once the camera system has been reset to HDCP problem has been fixed.

  3 tips on how to manage the flow of both BC I was hoping to give each player to medis/streamer a port on the router, but I'm still short of some?

  Once configured, I was hoping to use Time Machine from time to time, which means I needed to take the TC on the network and replace it afterwards or is there another way?

  A lot of questions, sorry. Networking is a pretty big unknown.

  Thanks a mil,

  CAPO Dino

  Run the cable to the Lan port of the router to the WLAN or a LAN on the TC port?

  Yes, at least to make the configuration correctly.

  I have to configure EI?

  Possible... Although it should have always in bridge.

  Always start a new network with a complete factory Setup configuration.

  Start from a factory reset. No files are lost on the drive hard in doing so.

  Universal factory reset

  Turning off the TC... That is, remove the power supply cord or the power at the wall outlet, wait 10 seconds... Hold the reset button... be nice... Turn on always even now in reset... and keep holding in for another 10 seconds. You may need assistance because it is difficult to hold in reset and power on. It will show the success quickly flashing led front. Release reset... and wait a few minutes for the TC to reset and return with the factory settings. If the front LED flashes quickly you missed and simply try again. The reset is quite fragile in these... Press the key while it is just click away and not more... I've seen people bend lever or even break. I use a toothpick as a tool.

  NB. None of your files on the hard drive of the TC are removed... This simply clears the settings of the router of the TC.

  Connect as you said... Ahmed to TC WAN LAN.

  Make the configuration of the TC. It is necessary to bridge... (Tab network, router mode... OFF (bridge mode).

  The Internet tab should also be on DHCP.

  You should see that it gets an IP address from the Fritz... and passes DHCP requested from customers (without wireless or ethernet) through to the Fritz so.

  2. I want that the cable Ethernet of CCTV through the TC rather than use one of the ports on the router.

  In bridged TC should not be a problem.

  3 tips on how to manage the flow of both BC I was hoping to give each player to medis/streamer a port on the router, but I'm still short of some?

  Transport CANADA ports should work.

  However if you are having problems... now go out and buy a 8 ports gigabit switch... It is extremely cheap point now and better than being frustrated by the lack of ports. I run a complex system... but everything is connected via a 16 port gigabit switch. So I never need to mess with the majority of the cables... it does not move even if Exchange you routers and AP autour.

  Once configured, I was hoping to use Time Machine from time to time, which means I needed to take the TC on the network and replace it afterwards or is there another way?

  Which should be as good... but I also warn you that Mac OS is lost very quickly now. It must connect by ethernet or wireless directly to TB without going through the Fritz. For some strange reason, Apple have evolved in network features that are not compatible... for example, Hello is very important and the Frtiz could be contravention.

  http://www.IP-phone-Forum.de/showthread.php?t=281365

  Just do a google for Fritzbox and Hello... you will find many articles... There are questions.

  Yes for apple not in line with the standard network world.

  As you can see other problems may arise as quickly...

  One of my solutions is to use the static IP address instead of the Bridge mode.

  Here's a post I did with a bunch of screenshots to explain it.

  Try it and see if it helps... assuming that you would have trouble...

  I can give specific information if you give me some screenshots of the configuration of the Frtiz... LAN and DHCP IP range.

  Re: time capsule Airport Guard disconnection

• PSC 2510: PSC 2510 Windows 8.1 - new router - can't change network settings

  OK so I got a new router so the IP address has goen of 169.254. * to 192.168. *.

  The page configuration network bed 169.254.124.x as the IP address and wireless can be found as the SSIS is hpsetup.

  I connected the USB cable, downloaded the HP printer Assistant Installer download and installed and it works great via USB.

  My question is how to operate via the network (wired / wireless).

  It is not rocket sceince, I spent hours tryign to make this work. The Wizard Windows Vista let me set it up easily, but what is the alternative Windows 8!

  Hi rewn,

  Thank you for your answer!

  If the router is WPS enabled, then following the instructions in the video that I have provided should allow you to connect. Otherwise, if it is not connected, you can use always an Ethernet cable from the printer to the router, or a USB cable from the printer to the computer.

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  Hope that answers your question and have a nice day!

• Time Capsule missing after installing new router

  I recently installed a new wifi router for my home network. Previously, I used only my time capsule to back up data and intend to continue to use it for backups. However, with my new router, I can't find how to access the time capsule to keep backups. I have time capsule directly connected to the router via ethernet and it will still not appear in AirPort Utility or enable Time Machine to find.

  Any suggestions?

  Everything has changed.

  With a new router, you have a 'new' network... and the time Capsule is to remember the parameters which it was equipped to work in your 'old' network The time Capsule is lost and he can't find his way.

  Reset to return to the default settings Time Capsule

  Connect it to the router

  Set up the time again to work with the "new" network Capsule

• got a new router how to connect my old again router Extender?

  My ISP has given me a new router. How can I connect my EX2700 existing to the new router extender? I tried just acting as if there had been no previous router, but it did not work.

  Resetting the Extender.

  Then Configure the extension once more.

• need help connecting HP envy 4520 with new router

  I have a new router. Cannot find where to change the settings of the printer. Cannot print.

  Reset the printer to the default network.  Then use the front panel wireless configuration wizard if your printer has it.

  Replacement/change your wireless router, try here.

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

  Make sure that your router is set to a fixed channel wireless as the 1, 6 or 11, never 'auto '.  Try channel 1 first and then the other one at a time.  Make sure that the printer and the router are spaced at least 5 feet.

  Brand and model of modem and router?

  However, if you have a gateway device (modem + router), all gateway devices are terrible for connectivity and wireless performance.   If this does not work, suggest you put this bridge in full bridge mode device and install your own router of high quality that YOU have full control over.