NIC teaming on ESX4.1 with Dell PowerConnect 2816
I'm stuck trying to get partnering work... I hope someone can help! I'm under ESXi 4.1 (vSphere), on a server with 2 GB for a Dell PowerCOnnect 2816 cards, supporting 802.3ad
Here's what I'm doing and the result:
1. I added a second NETWORK adapter under vswitch0 properties (in ESXi 4.1)
2. I went to vswitch0 | Port properties then the consolidation of NETWORK cards and set the active adapters and as road based on IP Hash load balancing
3 apply/close my way and ESXi now shows 2 map NETWORK interface connected to the vswitch (and everything still works fine).
Question 1: Shouldn't I lose connection to ESXi at this point?
4. I go to the page OpenManage and have setup a group LAG (1) with load balancing the value "Layer 3" (which should be the IP Hash I think)
5. I add 2 ports to the LAG group
6. I lose my connection to the server. If I remove the ports in the Group LAG then the connection comes back.
ABOVE 2: why the connection disappear? Expected the cluster NIC sync/speak to the LAG on my switch?
1: you can always access ESXi through TSM (Tech Support Mode) of the local console. This article explains how to:
http://KB.VMware.com/kb/1017910
If something goes wrong and you need to reset the network configuration, you need the command-line tools esxcfg-vswitch and esxcfg-vmknic. See the help pages for these commands for more details how to use (there also many guides online as http://www.2vcps.com/2009/11/22/esx-commands-esxcfg-vswitch/)
Also, there esxcfg-cfgbackup who should be able to create a backup and restore it later if necessary, but I have never used this before ordering. Seems simple.
2: I do not think that it is replaced by default, it should inherit the policy level superior vSwitch.
Tags: VMware
Similar Questions
-
NIC teaming with the IP hash load balancing
Hi guys
I have a virtual machine with a VMXNET3 10 Gbps. It is usually have a heavy traffic with a special server and saturate one of my two physical NIC of 1 Gbps in its PortGroup. I want to know what's going to happen if I turn on "NIC Teaming for this portgroup with basic IP hash load balancing". In my case the source IP address and destination are not change so the aggregates of traffic between my two physical network adapters?
To avoid saturating completely the two 1GbE NIC, it can also be useful to look in charge based on the grouping and the NIOC. It will ensure that the other streams of traffic VM are not crushed by this machine a virtual when it saturates a network card. The disadvantage is that it requires Enterprise Plus licenses (using a dvSwitch).
-
Reference Dell PowerConnect 6024F get mac by ip with arp and more option
Hello in the DELL community.
I hava a little question, and hoping to find some answers here ;) I'm writing a small script, and in this script, I need to get the mac address is to link to Ip address of the ARP command. I am using telnet to connect to DELL. But the show arp command displays a lot of information, a huge list of ip. I tried to analyze, with the '
' option and press etc., but it's a very slow procedure. Two main issues:
1. how to get the mac address and link it to the IP by ARP command
2 how to get rid of the option '
'. I mean show cli without I thank the of to get answers.
P. S.
===========================
Switch: Dell PowerConnect 6024F
# See the worm
SW version 2.0.0.19 (date may 5, 2008 time 16:33:30)
Start the version 1.0.0.13 (August 13, 2003 time 15:28:31)
HW version 00.01.64
#Show arp? -> watch only
Show arp
Terminal Server? -> watch only
Terminal Server
historyHe might have an OID you can pole for this info. all the OIDS are in the MIB that are included in the download for the firmware.
www.dell.com/.../DriversDetails
If you do not find one in the MIB, you might try a SNMP walk on the switch to see if you can identify an OID that will provide you with this info.
-
Problem with the Dell powerconnect 5424
Hi all!!
I got 2 switch dell powerconnect 5424. I set them up with an IP and everything goes well (for now).
But when I connect a switch on the network I have this message:
1 January 2000 00:01:07 % STP-W-PORTSTATUS: g21: STP Forwarding State
1 January 2000 00:01:27 % STP-W-PORTSTATUS: g21: STP Blocking status
1 January 2000 00:01:27 % STP-W-LOOPBACKDET: g21: STP loop detection.
1 January 2000 00:01:42 % STP-W-LOOPBACKDETRSLV: g21: fixed STP loop detection.I do not understand because there is only the network (port 21) and my computer that are not connected so no possible closure.
There is the same problem with the second switch, so I think this isn't a hardware problem.
Someone has an idea to help me?
Thank you
-
Problem with routing/circuits between SG300-10 and Dell Powerconnect 5224
Hello
I just bought a SG300-10 switch and loaded new firmware 1.27 on it. Configure my VLAN and trunks, but I have a weird problem that I can't seem to understand. It may be something small, I'm missing, but no matter, I have been scratching at it all day and I kicked in the butt. If anyone can point me in the right direction or maybe something that someone see in my config which is wrong, I can get the terminology/theory wrong, after all, I just spent my CCNA :)
My configuration:
I have the SG300-10 as my switch and changed over to L3, so it may be my core of my small network. On port 1, vlan 200 is configured as my unidentified native PVID and I put it to 210(LAN network) to trunk VLANs, 220 (management vlan) on the tag to the Dell powerconnect 5224 24port switch. On port 1 of the Dell switch, I install as a trunk it as well with the same configuration (vlan native of PVID unidentified 200, 210 and 220 tag trunking).
I have installed virtual interfaces on the SG300 for each VLAN (vlan 210 = 192.168.210.1/24, vlan 220 = 192.168.220.1/24) and on the Dell, since this is a feature of L2, I changed the vlan 1 to 220 management and assign the IP 192.168.220.2/24.
Now, since the SG300 web interface, I ping IP management Dell (192.168.220.2/24)successfully and vice versa, can ping from Dell web interface to one of the IP of the bridge VLAN (210.1 & 220.1) successfully so that test, to me, looks like the Dell communicates with the SG300.) I also have the default gateway of the Dell 192.168.220.1 printer value.
Server IP: 192.168.220.10/24
Workstation IP: 192.168.210.80/24
Now the dilemma:
I have a server plugged into switch port Dell 2 (configured as 'hybrid' because there is no option to access, value 220 PVID, vlan, worth 220 Untagged) and from the server, I can ping IP management dell very well switch and can ping the IP of the gateway of great SG300 so. On the SG300 switch, on port 2, I plugged in a workstation (configuration is in access mode, vlan 210 unidentified) who can not ping the server plugged into the dell switch. The workstation, I can ping all the SG300 interfaces and also the IP management dell but I can't ping the server.
Any ideas anyone can provide is much appreciated!
Edition of VLAN.
Lenell, thank you for the call tonight. It seems that we have found the problem. The SIN, although it is configured with a default gateway, the gateway that brings 0.0.0.0. We also checked the NAS works from the same subnet to connect but fails outside of the subnet. Conversely, we checked 2 computers have no problem to connect through the VLAN level 3.
I hope we got the right direction.
-Tom
Please evaluate the useful messages -
Override the port NIC teaming with powercli group?
Hi all
Any chance you could lend a hand?
I have a powercli script that goes out to all of my ESX 4.0 host and add a new port group to vswitch1 with a new VLAN ID. That works well, but I also need to override the NIC teaming on this port group, to set an active NIC and the other to be the backup. (we put NIC failover port groups not the vswitches).
I see ways to change NIC vswitches grouping settings, but am yet to find a way to change the settings of the NIC collection for groups of ports themselves with powercli?
Can someone shine a light?
Thank you
Try something like:
Get-VirtualPortGroup-name '
' | Get-NicTeamingPolicy | Game-NicTeamingPolicy - MakeNicActive "vmnic1" - MakeNicStandby "vmnic0". I hope this helps!
-
Hello
DELL powerconnect 6224 reference.
I want to access the management of a different VIRTUAL LAN VLAN.
The management of VLANS is 100 of VLAN. not the routing
My computer is vlan 60 (192.168.60.10) and I want to connect via ssh or http (192.168.100.1) to manage my switch.
Thank you for your help on the command line
The management of VLANS on the 6224 is not routable. So, you will not be able to access VLAN 100 from any other VLAN. However, you can manage the switch from other VLAN IP addresses. So if VLAN 60 has an IP of 192.168.60.1 you can http and ssh to it. And if the VLAN routing is enabled you have access to 192.168.60.1 on the other VLAN.
See you soon
-
ERROR WITH "DELL WIRELESS WLAN CARD WIRELESS NETWORK CONTROLLER.
GOT AN ERROR MESSAGE SAYING "DELL WIRELESS WLAN CARD WIRELESS NETWORK CONTROLLER STOPPED WORKING AND WAS CLOSED" AND NEED TO FIX. WHAT SHOULD I DO?
Hello
Actually try updating your driver and check with Dell Support and Forums if necessary.
Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlDownload - SAVE - go where you put it - right click – RUN AS ADMIN.
Dell - drivers
http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHSYou can download several at once however restart after the installation of each of them.
After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
manufacturer of system become your backup policies).Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
updated drivers.I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
are almost always old, and you can search drivers manually as needed.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspxDell support
http://support.Dell.com/Dell forums
http://en.community.Dell.com/forums/
I hope this helps.
Rob - bicycle - Mark Twain said it is good. -
black screen and nice white cursor and Ctrl alt del will not work, I can not update shell
black screen and nice white cursor and Ctrl alt del will not work, I can change the shell to the Explorer, but I can't unload or load the hive, what should I do?
Hello
Your question I know that some of these methods is not available now, however, all
Convenience store is included just in case where win you some access as you try to solve the problem.You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
on devices and UNINSTALL - REBOOT.Another method to try to get to the desktop (try in normal Windows Mode without failure)
CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
by tapping F8 as you start several times.First check this thread in case it is simple and if not to come back to this thread.
Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
That there is no information on a black screen as it is on a blue screen just adds to the
Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
Google to see the proposed repairs, whom some have worked however these cover a wide
field efforts.Here's a video of one of them.
http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1
Here's another fix
http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.phpYou have a Vista disk? You can try restoring the system to it. If you don't have the disks your
system manufacturer will sell them at low prices. Or try in safe mode if you can get there.How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.htmlYou can create a recovery disc or use someone even version (making the system restore it)
must be bootable).How to create a Vista recovery disk
http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html------------------------------------------------
These require the correct Vista discs since you can not start safe mode.
Try the Startup Repair tool-
This tells you how to access the System Recovery Options and/or with a Vista disk
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxTry recovery options Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.html-----------------------------------------------
Here are a few Google searches where many have found different solutions:
Vista black screen - check that a 1st
http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10Vista black screen Solution
http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQIVista black screen Fix
http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI-----------------------------------------------
If necessary and you can access all ordinary Windows.
You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation
(if all goes well, the data records and need to reinstall programs). Be sure to do a good backup or three.You can use another DVD that aren't copy protected but you you need to own
Product key.On-site upgrade
http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htmIf nothing works, you can make a repair facility that must save the data but you will need to
Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
need to know your product Code.This tells you how to access the System Recovery Options and/or a Vista DVD
http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-consoleHow to perform a repair for Vista Installation
http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html---------------------------------------------------------------------------
Another method that works sometimes: at the command prompt, type of Vista startup disk:
(a line type or copy and paste one line at a time and hit enter - enter a bracket)
or "BOLD")c:
cd\
CD c:\Windows\System32\winevt (there is a space between cd and C :)
Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)
RESTART Windows
I hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Connection SAN Dell PowerConnect 6248
Our switch in our network is the Dell PowerConnect 6248. This switch has a SFP module.
I was wondering if I could use this module to connect my SAN [activeRAID 32 TB of storage active destocking] and have access to the storage as a network or NAS drive Bay.
To be more precise I'll be plugging the controller [HBA] San to the SFP module on the 624 of Dell PC via a cable Fibre Channel LC.
I'm new to SAN configuration and look for the best solution to access the storage on my network.
Everyone has implemented a San with the SFP Module before; If that set up your look like?
Fibre channel and ethernet/IP are not compatible protocols without another device that can translate. The 6248 has no support for FCoE. There are switches that support both they are called network switches convergent or unified, although generally the traffic is still separated.
-
Difference between Dell Powerconnect N4032F and 8132F
Hello!
In the last days, the Dell PowerConnect 8100 disappeared from the Dell Web site and now, the M4000 series with the same characteristics are presented.
It's just a change of name or these devices differ in some way? The M4000 firmwares is usable on 8100 switches in the future?
Thank you
Kind regards
Stril
Dell PowerConnect N4000 switches series both Dell Networking PC8100 series share the same version of the firmware of the image (for example, N4000v6.1.0.1.stk). The Dell Networking N4000 series switches can be stacked with switches Dell Networking PC8100 of the series with any battery necessary for the performance of 6.0.0.8 or later firmware (6.1.0.1). Dell Networking PC8100 switches can support the firmware both 5.x and 6.x versions, but Dell Networking N4000 can support only the 6.0.0.8 and later versions of firmware (6.1.0.1)
I hope this helps.
B
-
Hello:
I am collecting information to configure NIC teaming on my server Dell poweredge r420.
Other posts I've read it is mandatory, installing broadcom software and update the firmware of the NIC (Broadcom Netxtreme gigabit ethernet).
I can't find the broadcom advanced control suite window to set up the consolidation of network cards.
Can someone help me?
You can access the Web from Broadcom site and download it here: http://www.broadcom.com/support/ethernet-nic-netxtreme-i-server or there are updates on the Dell Web site: http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/poweredge-r710?driverId=2T17H&osCode=WS8R2&fileId=2961022443#
Hope one of these works for you.
Wheeler Mitzi (Mitch)
-
Reference Dell PowerConnect 2848 OID for CPU time and memory
Hi all
This is my first post in this forum. I searched all the messages that can solve my problems, but I could not find so if there is already an existing post and I couldn't find it please guide me to it.
My case is. We have a few Dell PowerConnect 28xx switches in our network. We want to monitor things like the CPU, the temperature, the use of the RAM usage. We use Solarwinds IpMonitor monitoring tool. I downloaded the MIB, I could find the download of Firmware from Dell drivers and downloads page. I went through the entire MIB, but I couldn't find an OID for the foregoing.
So if anyone can help me please what OID is used for usage of CPU and RAM temperature it will really help me.
Please let us know in case we need more information on my side.
Thank you
Frank Moreau
I did use SNMP on the 28xx but here are some various sensor OID, I used for the N-series, as well as some older models Powerconnect. I don't know if they will work for the 2xxx, but you can try one or two and see if they work.
N - Series (FW 6.2 and later versions) temperature OID
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.5.1.0
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.5.1.162xx (3.0.x.x firmware or later-, some may also work with 2.x firmware)
Temperature OID
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.2
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.3
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.4Are the OID to use CPU for N-Series switches
1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.1 (total free memory)
1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.2 (total memory)
1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3 (table for the following...)
1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.1 (index)
1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (name of the process using CPU)
1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (% CPU used by the corresponding process)
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.4.0 (cumulation of all the activity of the CPU)
1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.9 (CPU utilization shows 5 s, 60 s and 300s).OIDs memory
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.1
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.2
Power supply OID
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.7.1.2
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.7.1.3
OIDs of fan
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.2
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.3
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.4
. 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.535xx (2.0.x.x or later firmware)
Temperature OID
. 1.3.6.1.4.1.89.53.15.1.9
. 1.3.6.1.4.1.89.53.15.1.10
OIDs of CPU
. 1.3.6.1.4.1.89.1.6
. 1.3.6.1.4.1.89.1.7
. 1.3.6.1.4.1.89.1.8
. 1.3.6.1.4.1.89.1.9
OIDs memory
. 1.3.6.1.4.1.89.29.11.1
. 1.3.6.1.4.1.89.29.11.2
P.S. The OID
. 1.3.6.1.4.1.89.35.5.1.1.2
. 1.3.6.1.4.1.89.83.1.2.1.2
. 1.3.6.1.4.1.89.83.1.2.1.3
. 1.3.6.1.4.1.89.83.1.2.1.4
. 1.3.6.1.4.1.89.53.15.1.3
. 1.3.6.1.4.1.89.53.15.1.3
OIDs of fan
. 1.3.6.1.4.1.89.83.1.1.1.2
. 1.3.6.1.4.1.89.83.1.1.1.3
. 1.3.6.1.4.1.89.53.15.1.4
. 1.3.6.1.4.1.89.53.15.1.5
. 1.3.6.1.4.1.89.53.15.1.6
. 1.3.6.1.4.1.89.53.15.1.7
. 1.3.6.1.4.1.89.53.15.1.8for old firmware - if the 35xx above does not work:
Temperature
1.3.6.1.4.1.674.10895.5000.2.89.53.15.1.9 (Celsius)
1.3.6.1.4.1.674.10895.5000.2.89.53.15.1.10I hope this helps.
B
-
Hello everyone.
The company I work for, I test switches to see who is good and who is bad. I've already marked the switch in question as 'bad' for these mistakes - but I've never seen this error before. My colleagues have not either. Therefore, I ask the community what kind of error is what it means and whether it is potentially fixable.
My device is a Dell PowerConnect 3524. He is currently out of warranty.
What I did: I have deleted the startup configuration and then run the Setup Wizard. I put an IP address, gateway, and password. The rest, I left the default values. This configuration works on all switches that I have ever tested, including this model, so I think that this configuration is not serious.
Then I plug in an ethernet cable in all ports and the other end into a very small 5 port switch that also has other trendy items above, the phone and my main computer. They all get internet, I don't think that there is a problem.
I plug another cable in another port of the switch and the other end in a laptop sitting on top of the switch (my laptop test).
I start ping the local firewall and run it with the "-t" parameter so it does not stop.
It is fine for about 5-10 minutes usually. I can trade ports and others and she'll pick up ping soon and do what it is supposed to. After plugging into the wrong port, (7 or 8), I get the error "SW3P_callback_rx_frame - intervention arp - put the scrapped." and cannot pass traffic. PuTTY shows that the connection is established and transfer, but the ping is not possible.
I am only an intern, this switch is not vital and will be sent to the "cemetery" and all my business done with switches will be. I am just curious to know what it is. Anyone know what it is and what could be done to solve the problem?
Thank you for your time!
I couldn't find any relevant information on this error message. With errors that occur only on specific ports and a new configuration, it really sounds as a kind of material error. Will there be another message that accompany this message? If you haven't already done so, re-flashing the firmware of the switch can help ensure that the message is not caused by an image that has become corrupt.
-
Dell PowerConnect 6248 10 GB ports reference works do not
Hello
We have recently installed a module SFP + (part # c107d) in our Dell PowerConnect 6248 switch. The switch does not seem to see the module because before install us the plug-in, it showed a port xg3 xg4, and after the addition of the module, it shows that these ports.
So I have a few questions:
Is the SFP + above compatible with this model of switch?
If so, how can verify us that the ports are active?
Here is the result of the port details:
#show interface ethernet 1/xg3 in detail
Port Type Duplex speed Neg Admin link
A State
----- ------------------------------ ------ ------- ---- ----- -----
1/xg3 10G - level s/o unknown Auto Up Down
Port description
---- --------------------------------------------------------------------------
1/xg3
Flow control: enabled
Port: 1/xg3
Belonging to a VLAN: access mode Mode
Operating parameters:
PVID: 1
Capture filtering: enabled
Acceptable frame type: no label
Default priority: 0
GVRP status: Disabled
Protected: disabled
-Other - or ITU (q)
Port 1/xg3 is a member of:
Rule of VLAN name evacuation Type
---- --------------------------------- ----------- --------
1 by default not marked by default
Static configuration:
PVID: 1
Capture filtering: enabled
Acceptable frame type: no label
Port 1/xg3 is configured statically:
Output name rule of VLAN
---- --------------------------------- -----------
Prohibition of VLAN:
Name of VLAN
---- ---------------------------------
Port 1/xg3 Enabled
Status: Disabled role: disabled
-Other - or ITU (q)
Identification of the port: 128.51 shipping cost: 0
Fast port: No. (configured: no) root Protection: No.
Designated the bridge priority: 32768 address: 80:00:00:25:64:19:92:1 C
Identification of the designated port: 0.0 cost of access road designated: 0
Root regional CSE: 80:00:00:25:64:19:92:1 C CSE Port cost: 0
BPDU: 0 sent, received 0
Yes, this module is listed as compatible with the switch. It seems that you install in Bay 2? He may have listed these ports but they probably do not appear as active. Have you tried to make a connection with ports?
Maybe you are looking for
-
How to 'get the names of the tracks"in iTunes 12?
Previous versions had 'get' track names in the menu dropdown. 12.5 iTunes does NOT seem to have this option. So what can I do to use the internet and the Gracenote database? I found this page - but it doesn't seem to be any help, I have nowhere in my
-
Not cleared leaving privacy data
Clear privacy data on output are enabled but are not cleared. It appeared to start with the most recent version of Firefox because it worked OK in the past. Manual removal works very well. Update Samsung S5 on Verizon.
-
How to stop others see that I send an email to. Non-reciepients?
I have outlook express running on windows xp and I waqnted to prevent others to see that I'm sending emails rather than send them individually.
-
Original title: Point of entry not found I'm trying to run an old program, Manufacturer of T-Shirt Hanesand get the error, "the entry point of procedure SUnMapLS_IP-EBP_28 not found in KERNEL32.dll dynamic link library.I'm running Vista 32 bit.Any he
-
Driver for hp business inkjet 1100 Series, Windows Vista home Premium x 64
I recently bought a Dell Studio XPS laptop 1640. It has Windows Vista Home Premium x 64 operating system. My hp business inkjet 1100 printer series will not be installed with the hp installation CD. I need the correct driver. Apparently, hp does not