No amber light in the button walk / stop during sleep, now no blue light when Windows is running.

Similar Questions

• NB205 - white screen if I press the button walk / stop

  Hello

  I have problem with my NB205-325 bl, if I press on the power button then it will load the TOSHIBA logo and after, coming to screen empty and it does not start at startup. Everything was fine, if I used it the last time.
  OS: Windows 7 Ultimate

  What did I try?
  I gathered some information on this issue, and I found it helps sometimes if I remove the battery and remove the RAM. And if I was kidnapped ram, then I'll give you a few electritvy on this subject, but this did not help. (maybe I missed a part)? Also, I checked in my BIOS primary boot is my hard drive.

  My problem is same like in this video http://www.youtube.com/watch?v=LCm6BozBgAM&feature=related

  Anyone have any suggestions on this subject?

  Best regards, Olari

  Post edited by: Olari

  Hello

  Usually if laptop doesn't start and you get only a black screen, it seems to be a hardware malfunction

  First check out this article:
  [What steps must be followed if your Toshiba laptop does not start? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=21]

• HP DV9700 not start. Farm in seconds after pressing the button walk / stop.

  My HP Pavilion DV9700, who works under Vista, stopped working yesterday.  I never did at the Windows startup screen.  Messages on-screen messages which function key to press for configuration, see starting, etc...   then stops.
  
  It started a day ago. I don't think that windows is the question.

  I tried to hard reboot... blew compressed air into the power supply area... no change.

  Don't know what to try next.

  Thanks in advance for any help you can provide.

  Steve

  Had to take the machine a tech I know.  It was the motherboard.   Thermal paste had disappeared from the excessive heat of the CPU and GPU and the poor ventilation of the machine design.   Costly, preventable and unnecessary repairs... HP was worth investing in better design systemboard for their laptops and notebook computers.

  HP response... your notebook $ 1200 of the scrap and buy another... and they will add the warranty one year.

  They thought that 5-6 years I got my laptop has a long service life of the device.

  I was actually insulted by this response and doubt my next laptop will be HP.

  Thanks to those who have tried to help however.

• I woke up this morning and my iPhone 6 does not light. I tried to reboot it by holding down the button market / stop and the button "home" but the apple logo never appeared and I had on the charger for a while and still nothing. Please leave suggestions!

  I woke up this morning and my iPhone 6 does not light. I tried to reboot it by holding down the button market / stop and the button "home" but the apple logo never appeared and I had on the charger for a while and still nothing. Please leave suggestions! Thank you

  You can make an appointment at the Apple Store - Genius Bar store and bring it into service. You can also search an Apple Store - find a store - Apple.

• I used creative cloud perfectly until one day asked me to update and I clicked on the button. All software has now changed from trial version and I have right to use within 10 days. What should I do now? Can I go back?

  I used creative cloud perfectly until one day asked me to update and I clicked on the button. All software has now changed from trial version and I'll lose the right of access of Illustrator, Photoshop and InDesign in 10 days. What should I do now? Can I go back?

  Hi Emily,.

  Please visit: https://helpx.adobe.com/manage-account-membership/cc-reverts-to-trial.html

  I hope this helps.

  Concerning

  Megha Rawat

• MacBook Pro stops during sleep

  My MBP 15 "mid-2015 retina stop completely during sleep. Often when I get back to my MBP, I have to start from scratch because it stopped during sleep. There is no message in the log to indicate why it closed and no error messages or indications of kernel panic. Sometimes the power and battery and with or without the lid closed. Latest OS X with all updates applied.

  Reset the SMC (and NVRAM) does not help. Apple Diagnostics is no problem, and Genius Bar suggested I have first of all to make an OS X install excessive, then a clean install because they believe that it is a software problem. I tried to install too, and it made no difference. Pure install then, but I delayed, because it involves a lot of work in store again my work environment and data, it is not useless in current state - it's just a problem of waiting for the start up and then restore whatever, I was working on the last.

  Any advice?

  There is no message in the log to indicate why it closed.

  There could be.

  Wait until the Mac stops unexpectedly, and then check your system.log file to identify the numeric code associated with the stop. Read below.

  Locate the Console application - it is located in your utilities folder and looks like this

  

  You can find it by selecting utilities in the Finder go menu.

  Open the Console.

  If the list of newspapers on the left column is not already displayed, view journal list by selecting view list of newspapers on display menu of the Console.

  Locate system.log in the list, and then select it. Many date and time-stamped entries will appear, hundreds of them, and you need to find the relevant entries to your Mac problem.

  Do that type the word cause stop in the field filter on the top right of the Console window.

  Who will do all the log entries be hidden, except for entries that contain these words. There will be a numeric code associated with the entry of journal from «Cause of previous stop» What is this code?

• How to start the VPN connection when windows is running

  Original title: trouble with automatically the VPN connection

  Hi, I want to have my VPN connection to start automatically when windows is running.

  Simple version:
  I tried various different methods, including; Paste the shortcut in the startup folder and adding the task in the Task Scheduler.

  I have the same problems with both methods. Just the VPN starts automatically... I have to run it manually whenever I turn on the computer or wake up sleep mode.
  Does anyone know other methods finally a solution for the other two methods?
  In the version of the depth of the problems:

  Method of Task Scheduler: I get argument is not valid, it is even after I have successfully created the task and click OK. The task will not work, and also by some strange reason, my VPN password is not get recorded on my connection more. So now, I need to manually start the connection and type in the password. (I click on save the password whenever this does not work, when the task is active...)

  Shortcut to the startup directory: Simple and easy... It simply doesn't get it. I followed the steps very carefully and I'm 100% sure that I did it the right way...

  These links have good information on how to open a VPN connection to the Windows dΘmarrage

  http://www.dariancabot.com/2010/11/15/automatically-connect-to-VPN-at-Windows-startup/

  http://www.Buchatech.com/2011/04/configure-Windows-to-automatically-connect-to-VPN/

• OfficeJet Pro 8620: HP OfficeJet Pro 8620 button walk / stop keep flashing

  Condition:

  My Officejet Pro 8620 is about 1 1/2 years and all of a sudden it does not. (FYI: it worked again yesterday). My printer has been connected to 3 PCs in my house wireless, there is another printer (HP LaserJet Pro M401dw) in the same room connected to wifi even. Printer is plugged directly into the outlet. No attempt to replace the cartridge or install the new firmware recently.

  Location:

  This morning, I saw the power button flashes, in an unusual way, it flickered at a rapid pace, about 3 - 4 times per second. When I try to print something, the printer has not been to see the in my list of printers, so I try to touch the screen of the printer, but nothing happened. When I pressed the power button, it stopped blinking, and the HP logo was shown on the screen with a blue bar underneath. Then it was stuck there for hours. Tried the hard reset, use the tools of the firmware, connect my printer to my pc using cable, but my printer is not displayed on my pc (it is not detected by the pc, no new feature and nothing appear in "Printers and devices" when the cable is connected to my PC).

  So I unplugged the printer from the power source and wait a few hours, then reconnect the printer to the socket. The printer has started again with the power button / stop light up and the screen showing the logo of HP with a blue bar below the logo. But this time, after a few minutes, the screen is off, all buttons blink (home, help, back, wireless & power button) at a rate (about 3 - 4 times per second) fast, and after a minute or two, home, help, "back" button and stop brighter wireless (only flashing light up), but the power button keeps blinking. All the buttons and the display do not respond, press the power button / stop is unable to turn off the printer.

  I tried all possible troubleshooting methods suggested on this forum, but nothing to solve it, I hope someone in this forum can help me with this, thanks in advance.

  Hi @DenieceNg,

  It seems that the problems are on the increase, and maybe this could be related to a hardware problem with the printer.

  Here is the document of support for the power problems - printer does not turn on.

  If these problems persist, I would contact HP Technical Support because they may have additional resources that could help lead to a solution. What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:

  Step 1. Open the link: www.hp.com/contacthp/

  Step 2. Enter the product number or select Auto detection

  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.

  Step 4. Scroll down and click on: contact HP options - click Get phone number

  File number and phone number are displayed.

  If this helps you find a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• HP Officejet 4500 G510n-z all-in-one series, button walk / stop

  HP Officejet 4500 G510n-z series all-in-one wireless.

  When I press and release the power button, it does not start and no lights appear.

  If I press and hold the power button for about a minute, the printer turns on and works fine.

  To turn off the printer, I need to press the power button for about a minute.

  Hi @Tonyey20,

  Welcome to the Forums of HP Support! I see the power button on your HP Officejet 4500 is inadmissible, if you press and hold the button for one minute, the printer will turn on and work normally.

  I would like you to start troubleshooting here: The HP printer will not be running or to respond when the power button is pressed

  Please let me know the results. I'll watch for your reply.

  Thank you

• My triggers the mouse to the bottom of the actions on the buttons and STOP are ignored in 1.5

  Hey guys,.

  STOP triggers always seemed buggy, but once I have upgraded to 1.5, they do not exist. My calendar just right cheek on through them and the buttons that I put in place with the mouse down did not go to a specific label. My stage is set for AUTOPLAY. Is there a setting that could turn off actions and triggers?  I'm going crazy here with a deadline of tomorrow. Help, please!

  Thank you very much!

  Brian

  Brian-

  No, there is no adjustment.  In general, this means that there is a bug in the code for the action.  First, check if there are red warnings in the Panel (bottom right of the screen) warnings.  The next thing for you to do is to open a web Inspector as Inspector of Chrome or Firebug for Firefox to check if there is JavaScript not valid.

  Hope that helps,

  -Elaine

• Satellite A350 - 12j PSAL6E: Win 8.1 start-up without pushing the button works / stop

  Hello

  is there a way to boot the OS (WIN8.1) [system status: closed]
  without first pulling the screen upward and push the power button?

  FYI: I use an external connected HDMI screen/monitor!

  I know the typical rest on keyboard through BIOS, but use that requires a laptop in hibernation/standby mode.
  It bothers me a little every time up the screen and pushing
  Wake on Lan is not an alteranative as its connected via W - LAN

  Any ideas or suspicion appreciated!
  Thanks in advance.

  See you soon,.
  dirtyheizer

  Unfortunately, there is no other method to put the laptop, if the device has been turned off.

  You have to press the button to power ON the laptop.

• Satellite P200 - disabling Internet special button Close button walk / stop

  I have a Satellite P200. Recently, the problem that my Internet push button itself so multiple Firefox Windows begin to appear at random intervals. Sometimes 2, sometimes it's 30. Needless to say, it's pretty boring.

  I found where I can customize the buttons and make the Internet button open a different program, but it doesn't seem to be an option to turn it off completely. If I "Unregister" the Internet button, then it goes back to the default function of opening a Web browser when it is pushed.

  Is it possible to completely disable these keys?

  Thank you!
  Jason

  Hello

  I have the same model of laptop and disabling option is not known to me. What you can try is to remove the utility of technical support of added value package button.

  In Control Panel, you will find option programs and features. Click to remove the VAP. Generally, it should ask you to change the installation and you can choose which part of this package can be deleted, if it is not completely remove the VAP.

  Download the last option in the download page of Toshiba, but when the facility starts choose custom installation and uncheck the box in front of the technical support of button utility.

  So for now I see it as the only possible solution.

• M1132 don't wake. When I hit the button start-stop, but it then doesn't not scanner/photocopy

  Hello

  I just bought this Laserjet M1132 MFP.

  He goes to sleep and the next time, it won't wake up. I jiggle with all the buttons on the machine, without exploitation. I use win8. Preferences has nothing on the sleep options.

  When I click on one = off button shut down shut down and restart, it prints. But then it doesn't scan or photocopy antything, it does not do anything, just blank pages.

  I need to plug in the printer power cable off, hang it upwards again once, and then it works.

  Really frustrating feature

  Well, directly plugin was not the solution. I updated the win8 Office and downloaded and updated the firmware of the printer from the HP website.

  Now he'll still sleep and yet not wake when I have something to print, send, but hit the on/off button wakes up the computer and it scans and photocopies now after the update of the firmware and update the computer.

  Thus, no congratulations, but thanks

• How to make the beep I trash a message now? You know, when spam happens.

  Sorry, you do not deserve the beep. I just wish that Thunderbird would STOP send me features I don't want and keep the interface I'm used to.

  I use the button or the delete key.
  More details on preventing you to do would be maybe useful.

• Dell XPS 13 stop during sleep after bios upgrade

  Recently updated my BIOS Dell XPS 13 L321X-the worm 8. Since then, whenever I close the lid and put the laptop to sleep for several hours, the processor seems to come and the backstory is very hot. When the cover is opened, the screen remains blank and no wake mode 'sleep'. The only recourse is to make a hard stop with the power button and then restart. The laptop restarts then black screen troubleshooting, or select the normal startup of windows. Since then, I tried to update all the drivers, but still no luck. He continues to run hot and won't start after placing the phone in sleep mode.

  Any help is appreciated!

  Divider ~.

  Thanks for the quick response!

  To review, my problem started when I updated the BIOS to ver. A08. Before reading your solution, I ended up flashing my BIOS downgrade - worm. A07.

  I started a series of applications and then closed the lid, let go in mode "Eve". After a long period of time, I opened the lid and the wake of the computer normally with no issue. No screen cases, no empty overheated. And not need a hard stop and restart with the power button.

  Hope that this remains the case, I will record your steps suggested in case reports of problem, but so far, it seems that BIOS upgrade vA08 was the problem and a reflash with v A07 was the solution.