No audio device located

Similar Questions

• No its "No. Audio Device" IDT High Definition Audio CODEC. (The device cannot start code 10) location 65535 internal high definition audio

  I need help.  suddenly I have no sound. the error I got was "no audio device" Microsoft Fix it Center found problem but did not set. Just says "problems with noise and acoustics. No sound"but the situation is"not fixed ".

  What can I do? really appreciate some good advice on how to fix or how to get it fixed.

  I need help.  suddenly I have no sound. the error I got was "no audio device" Microsoft Fix it Center found problem but did not set. Just says "problems with noise and acoustics. No sound"but the situation is"not fixed ".

  What can I do? really appreciate some good advice on how to fix or how to get it fixed.

  I would appreciate if you visit this web site.

  http://support.Microsoft.com/kb/943104

  Answer please, if you face any problem.

  K M JAI Support general (INDIA)

• Motherboard integrated audio device missing randomly after turning on the computer.

  Hello

  Old location:

  I recently changed my laptop Elitebook 2540p motherboard. When I installed windows 7 Enterprise 64-bit on my computer the computer lists not all audio devices in the Device Manager page. I checked the bios for all faulty settings and they are all good. Theres no yellow mark in the list of devices is and all the drivers appear to be installed.

  New location:

  Installed windows 7 and computer again found / installed normally audio devices. I tested computer for hours to read the audio data from it and everything worked well. I restarted computer several times / re installed the battery on the computer. A reboot the computers audio button mute fast under the screen seems to be orange and the speaker sound in windows icon has been marked as X I have check the list of devices in Device Manager and there is no audio device listed (no sound device at all). Once I restarted computer and before the computer started downloading windows I pressed the mute button and it turned blue. Then I went to windows and audio devices / audio devices has been registered and work / sound working again.

  Old location:

  I have motherboard integrated IDT audio device.

  When I try to install audio drivers from hp for 2540p site I get "your system does not have the minimum requirements for this patch." And the Device Manager does not list all IDT audio devices.

  I then installed xp, computer peripheral audio IDT normally found and sounds work properly.

  New location:

  After I made the new windows 7 install and all my audio drivers installed / devices showed in the list of devices / audio worked / I downloaded sound drivers driver HP site and install them to the computer.

  Audio problems has not appeared again after my screen mute button HP turned to orange / speaker Windows sound was marked as X / computer didn t found no audio device.

  Currently waiting if the problem happens again and try to think what would cause this (hardware or software problem)? And how to solve this problem permanently.
  

  UPDATE: I have fully charged battery / computer was off while what to do and the problem came back. Mute button fast turned to orange. No audio devices and speakers marked as x. "No audio device installed".
  

  I then installed USB headset and the computer recognizes the and the sounds are use of usb device. Theres still no IDT audio device, shown in Device Manager. Only usb headset work.
  

  Any help for this problem?
  

  -BIOS is updated to the latest version of the HP driver download center.

  -All windows drivers are installed.

  -Bios configured correctly.

  -Reassembled the motherboard and tested all the cables are correctly placed.

  EliteBook 2540p

  Windows 7 Enterprise 64-bit

  Motherboard Info: VB841AV product number

  Product model BU RCTO i7-640LM Mfdf 2540p

  598762-001 MB SYS W/PROC CORE 2 DUO 2.13 GHZ

  P.S. This thread was moved from the company - Compaq, Elite, Pro for laptop - PC Compaq HP ProBook, EliteBook, slate/Tablet PC, Armada, LTE. -Hp moderator of the Forum

  After change of motherboard second the audio computer´s worked well and the audio devices never disappeared from the computer. The first new motherboad that I had and I changed had broken the IDT audio chip.

• Tecra 9100 - no audio device after XP Pro install

  The audio device does not appear after installation of xp pro sp2 on Tecra 9100.
  I tried allsorts to research on forums and websites.

  I found install them drivers on this site but used to my laptop.
  I need to locate the audio device before get drivers?
  I know this is a very old problem but I tried for 12 months with no result.

  Any help appreciated.

  WOW!
  You are still using the good old classic? Surely she s or it was a nice laptop but maybe it's time for something faster? ;)

  Back to your question;
  On the European driver Toshiba page, you can find drivers Tecra 9100.
  You should look in the Archive (in product type click Archive instead of the laptop)

  There are two audio drivers for Win XP.
  She s Yamaha audio driver version
  -5.12.01.3141
  -6.13.10.2152

  I guess the 6.13.10.2152 is a more recent who is available and I think that you should use it!

• Laptop of HP ENVY m6: high definition Audio Device a yellow exclamation

  Hello

  I have a yellow exclamation next to the high definition Audio Device in Device Manager. He says that I have the best driver when I try to update the driver software. FYI, the Realtek one is good. I need to fix the high definition Audio Device.

  My product number is G6R97UA #ABA.

  Please help me!

  OK, it's exactly what I thought it was in the first place... the Intel HD Audio chip.

  Try to manually install the driver that I posted as follows.  If you have not deleted the file I posted, go to Device Manager and click on the audio device HD requiring the driver.

  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the folder of the driver that was created when you ran the file.

  This file will be located in C:\SWSetup\sp72370.

  Make sure that the include subfolders is selected and see if the pilot goes like this.

  Then restart the PC.

  If you have deleted the file, download and run again the driver, close the error window and follow the procedure above.

  I see the hardware ID you posted as supported in the driver file, so it should work.

• Qosmio G20 Win XP MCE: no audio device found

  Hi friends...

  IM using qosmio G20 Win Xp (MCE).
  The problem is that if I open the audio device and its control panel shows that is no audio device.
  But always in my device manager, I see that the audio drivers are installed for audio codec, video codec, inheritance... etc...

  When I boot the pc im able to adjust the volume with scroll volume control located on the laptop. I can see the blue wire shines increasing forward...
  But when it ends im not able to adjust the volume using the start scrolling...
  Can any 1 give me a cure?

  1 should I install * model MIDI MPU-401 device * or something else to work?
  2. the speaker of the system is ensured by * Harmon Kardon * y at - it a particular to install driver?
  Here's my query, which can be useful for solution providers...

  Thanks in advance...
  Raja...

  Make the path on your own, which can help others to follow... Raja

  Hello

  Why you n t update the pilot of its new?

  First go to the Device Manager and remove the sound card (mark and uninstall the driver)
  Then download the audio driver from the European driver Toshiba page and install it!

• Audio device problem on Windows 8 64 Y510

  Hello dear readers. I have a lot of problems with my audio devices after the operating system upgrade to windows 8 on my lenovo y510. First of all default settings and drivers that I am working as any other failure, are evidence of each pair of speakers (this particular machine has 2 x 2 speakers and a subwoofer) as different devices on my audio settings. This of course means that I can only listen to one channel which is frankly frustrating...

  I tried to update the realtek drivers, and after restarting, I as a single device. With the help of those who suggested on lead lenovo horrible failure page, so I don't even bother. I think that this may be connected to the lack of software Dolby Home Theater, but all attempts to install it gave rise to a message "pceee is not installed.

  Did anyone of you had similar problems on this laptop in particular?

  TL; DR I would spend devices 5 speakers 3 in peripheral location 5 1 speakers

  TIL: I'm a fool.

  Well, turns out I found that my original drivers for Vista work like a charm.

• Device Manager - unknown device + Hig Defintion Audio Device (Point of Exclamation)

  Hello

  I hope that someone can help you. The hard drive on my laptop of HP ENVY TS 15 (product number: E3S19UA #ABA) out crapped and I reinstalled Windows Enterprise 8.1. I downloaded and installed all the drivers from the HP website. When I look at the Panel, I have an "unknown device" and in the audio, video and game controllers, I have an exclamation mark next to the high definition Audio Device.

  I installed the HP Support Assistant and let it do its thing. That has not fixed the problem. When I look at the properties for the unknown device, I see the following in detail: "ACPI\HPQ6007\3 & 11583659 & 0" regarding high definition Audio, I see the following in the general tab:

  This device cannot start. (Code 10)

  {Operation failed}
  The requested operation failed.

  When I try to update the driver software fo the High Definition Audio, I get a message that "Windows has determined the software driver for your device is up to date.

  Don't know where to go from here. Any help or words of wisdom would be greatly appreciated.

  Thank you

  -Val

  You are the very welcome.

  This is defininitely the driver you need and you need to install it manually.

  Run the driver again.

  Go to Device Manager and click on the unknown device needing driver.

  Click the driver tab.  Click on set to update driver.  Select Browse my computer for driver software, and find the folder of the driver that was created when you ran the driver.

  This file will be located in C:\SWSetup\sp66078.  Make sure that the include subfolders is selected and see if the pilot goes like this.

  If this does not work, then back to her browse my computer for driver software window and then select Let me pick from a list of drivers for devices on my computer option, then select Have Disk and browse to: C:\SWSetup\sp66078\InstallFiles\Win8_1\accelerometer and select the HP Mobile Data Protection sensor from the list and see if the pilot goes like this.

  The HD audio device is the audio device Intel HDMI which could not install when you ran the graphics driver, so run it again and if it does not install, manually install the driver using the same procedure that I posted to the 3D driveguard.

  If it doesn't, then I remove the driver and tell you where to get the driver from, as I did for the above device.

• audio device on high definition audio bus

  I shot my SL400 with windows XP SP3.

  I've updated my system drivers by using the tool "system update" Lenovo. Although the audio driver is installed and the audio working there is a question mark and exclamation mentioning "audio device on high definition audio bus". the device instance ID is

  HDAUDIO\FUNC_01 & VEN_8086 & DEV_2802 & SUBSYS_80860101 & REV_1000\4 & 847CD8C & 0 & 0201
  kindly help!

  Thanks in advance!

  Hey man I solved that same question as you have it if your using xp for audio problem trying to load the driver manually in C:\DRIVERS\WIN\AUDIOC\WDM, for a video broadcast in audio HDMI, I think that you need to reinstall the video driver for HDMI and if the driver installation or locate the folder video driver to C:\DRIVERS\WIN764\VIDEO\HDMI it is because the audio and the video has the same HDMI system files necessary, sorry my bad English but I'm trying to help.

  Thank you

• I have a problem with finding a PnP USB audio device when you search for available audio devices.

  Hello.

  I am building an application that can find a PnP USB audio device and play a tone if the device is connected. I am able to search audio devices using "Sound Device Info.vi" of the lvsound2.llb that comes with labview.

  The vi can find the USB device in good conditions, but there are problems - I'll try to describe 2 scenarios.

  1. the USB device is connected before 'Sound Device Info.vi' is called for the first time.

  In this case, the program can find the USB device. If I unplug it, the device disappears from the list of found audio devices. If I reconnect to the same USB port, it reappears in the list. It's all good.

  If I reconnect it however a new USB port, the device is not found. This is not good.

  2. the USB devices is not connected when 'Sound Device Info.vi' is called for the first time.

  "Sound Device Info.vi" is not able to find the device. Disconnect and reconnect does not make a difference.

  I'm under labview 2012 on windows 7.

  I am running the application as an exe to build.

  I call 'Sound Device Info.vi' as a 'call for reference"and the reference is closed between calls to the vi. I was hoping this would unload the dll used in "Sound Device Info.vi" and would solve the problem, but it didn't.

  Is there a way to reset the information usb labview during execution?

  Concerning

  Stephan.

  Hey Stephan.

  The sounds screws require a DLL located in:

  C:\Program Files (x 86) \National Instruments\LabVIEW 2012\resource\lvsound2.dll

  Internally, LabVIEW uses the DirectX API to enumerate devices. The one caveat is that probe us for devices when loading the DLL. We probe not later. So that it works for Bluetooth, USB, fire wire, etc. devices that can be inserted or removed at any time, you control somehow when this DLL charge and discharge. To do this, please see the following document:

  Dynamically that I can load and unload a DLL in LabVIEW?

  http://digital.NI.com/public.nsf/allkb/77594203D78D12278625729100758BE5

  I would also recommend that you provide a Kudo to this idea:

  Updated library lvsound2 (Sound Input/output Sound live) to support audio devices change on the fly

  http://forums.NI.com/T5/LabVIEW-idea-Exchange/update-the-lvsound2-library-sound-input-sound-output-V...

• After you have reinstalled Windows XP my computer said that having no audio device. How to re-install a new audio device?

  After you have reinstalled Windows XP my computer said that having no audio device.  How to re-install a new audio device?

  A. Si you have the sound driver file install it normally

  or
  B. extract the files to a specified location
  go to Device Manager
  find the audio device with the yellow mark
  Right click and uninstall or update driver
  Select Advanced Setup
  the location of the file
  and follow the instructions

• Audio Device notfound & PCI on Aspire One device driver problem

  I have 2 Aspire One netbooks, both worked fine a major accident. I installed a new xp with SP3 and all the Acers site download drivers for my netbook by serial number. After that everything seems to work properly, I did an image and cloned the other netbook.

  Now when you open a youtube video element ends and I put in place an error on device configuration

  When I open my control panel and look at the sounds it says "no Audio device is found.

  I have a PCI device in Device Manager only configuration and have pinned it down for "PCI VEN_8086 & DEV_27D8 & SUBSYS_015B1025 & REV_02\3 & B1BFB68 & 0 & D8.

  I think that the problem of audio device or pci question are related and causing youtube video error.

  I checked the bios versions tonight and the computer has the latest version of the bios.

  Any advice? Thank you... My wife uses her netbook all the time that's why in the need to make it work again. My netbook is sitting most of the time until I travel. I have a 15 "aspire I used to use.

  Okay, better control the HardwareIDs, seems to be the microsoft high definition audio device.

  Fix Microsoft is necessary above all to the HD, device drivers are installed, but the patch will not pass on windows XP SP2 computers.

  See link: http://support.microsoft.com/hotfix/KBHotfix.aspx?kbnum=888111&kbln=en-us

  Open Device Manager by typing the command devmgmt.msc. Select sound, video and game controllers.

  If no driver installed uninstall one by one.

  Open the registry editor and navigate to the following location

  HKLM\SYSTEM\CurrentControlSet\Control\Windows\

  Change the CSDVersion value to 200. Restart the computer

  Download the Microsoft patch kb888111xpsp2.exe

  See link: http://support.microsoft.com/hotfix/KBHotfix.aspx?kbnum=888111&kbln=en-us

  After updating the patch install the audio drivers for the system.

  Restart the computer.

  Open the Registry Editor again.

  Locate the HKLM\SYSTEM\CurrentControlSet\Control\Windows path and replace the old CSDVersion value is in a 300 words.

  Realtek audio drivers:

  http://global-download.Acer.com/GDFiles/driver/audio/Audio_Realtek_5.10.0.6010_XPx86_A.zip?acerid=63...

• Windows XP my sound recorder audio device is a DODEC Audio USB, the volume and advanced is grayed, how do he turned the back?

  I just installed a turntable to record albums. I installed everything simply by following the instructions. The volume of the sounds and advanced recorder is grey and everything I do doesn't change it. Can someone help me?

  Hello

  You can view these methods:
  Method 1

  Download & install the previous version of the drivers for the sound card and check if it solves this problem.

  1. type devmgmt.msc in the search box start and press ENTER.

  2. in Device Manager, expand the audio drivers listed in the list of devices.

  3. right click on the audio driver > click Surdesinstaller.

  4 restart the computer and install the downloaded software.

  Method 2
  
  In addition, if you use a recording program, update or reinstall the program registration.

  Method 3:

  Please follow these steps to enable the "Windows Audio" service:

  1. Open the control panel of Windows XP by (depends on your settings in Windows):
     By clicking on "start > settings > Control Panel.
     By clicking on "start > Control Panel.
  2. Open the "Administrative Tools" Panel by (depends on your settings in Windows):
     Double-click the control panel 'administrative tools '.
     Click on "Performance and Maintenance" and then "Administrative Tools".
  3. Go to 'Services' Control Panel by double-clicking it.
  4. Locate the "Windows Audio" service.
  5. Check the "Status" column to see if it is disabled.
  6. If it is disabled, click with the right button on the "Windows Audio" service and choose "Properties".
  7. On the general tab, change it "Startup Type:" drop-down on "manual".
  8. Restart your computer.
  9. Follow steps 1-6 to open the properties of the Audio service 'Windows'.
  10. Click on the 'Start' button to activate the Audio service 'Windows'.
  11. You will now be able to change the control panel 'sounds and Audio devices '.

• No audio device. How to fix?

  When I go to sounds and audio devices through Control Panel there is no device listed for playback or playback of MIDI music. The box is grayed out, so I can't select another device. This happened after I deleted a program called HD ADeck from my computer but I can't find a way to reinstall.

  I searched the internet for solutions but have had no luck.

  I tried the system restore, but my computer could not restore to an earlier date.

  An online forum suggested I remove the current audio devices and reboot the computer, which should then restore the necessary readers. When I go in the Manager of devices devices listed for sound, video and game controllers are all working properly, but I don't see how to remove them. Also the location of them is unknown.

  Any help gratefully received. With our thanks.

  Hi LisaG123,

  Follow the steps in the article.

  How to troubleshoot sound problems in Windows XP

  http://support.Microsoft.com/kb/307918/en-GB

  How to update a sound card driver in Windows Vista and Windows XP

  http://support.Microsoft.com/kb/166774

• Audio device has disappeared. What should I do to restore it.

  I accidentally deleted my audio device.  How can I reinstall it?

  Go to your PC/Laptop manufacturers website, find their support page and for your PC/laptop, locate the drivers, download the audio drivers for XP and install, re-boot if necessary.

  See you soon,.

  Jerry