No brand ID is on the disk

Similar Questions

• EQL PS6010 online and I want to upgrade the capacity of the disk but original Dell drive are not available, it is possible to replace it with the original brand of Seagate.

  Hello

  One of my largest clients use a PS6010XV storage in production for 3 years. It is equipped with 8 disks SAS 600 GB drive HARD 15'000 rpm and shortly it will be out of space. He ask me full fill the table with hard 16 600 GB.

  My sales representative Dell told me that this kind of upgrade is not possible, the 600GB 15,000 rpm SAS drives is not available...

  My client is very upset by this situation and I'm trying to find another solution.

  Is it possible fill completes the picture with the original disc Seagate Cheetah 15K 3.5 "600 GB SAS 6 GB/s 24 x 7, type ST3600057SS instead of the original Dell disks?

  I can see the Dell drive (P/N 0944832 - 01) are Seagate brand and type is exactly the same.

  Kind eyes and waiting for your response

  Christophe

  Hello

  No, because it is custom firmware on the brand of Dell disks.  The EQL firmware will be search and reject non Dell/EQL brand discs.  Do not add any disk brand would also void the warranty.

  Kind regards

• JBOD Qosmio G20 - could not initialize the disk of 320 GB - 1RAID-0

  Hello, comrades Toshiba users,
  at first, I apologize if this question has already been answered, but I did not find the answer to my problem.

  One of my colleagues has a Toshiba Qosmio G20 with two 80 GB drives. Big 17-inch "surf-board-sized" computers laptops are not my cup of tea, but the Qosmio him quite well served.
  We tried to upgrade the two hard drives of aging in his laptop. With considerable experience in replacing the readers of the laptop, I didn't expect no particular surprise, but I was wrong.

  We tried to replace the original disks
  Bay 1: 80 GB Fujitsu drive, System
  2: 80 GB Fujitsu drive, data, RAID off the coast of the Bay

  with the new
  Bay 1: 320 GB WD Scorpio
  WD Scorpio 2: 320 GB drive Bay.

  The BIOS of the G20 is v1.30, the latest version. It recognizes new readers-, but one of the new marking as 1RAID-0 disks fails. After trying to "initialize" the 320 GB drive in bay 1 as 1RAID-0, on the third page of the G20 of BIOS, there is a disk activity, but the drive remains in JBOD mode.

  Unable to mark the drive of 320 GB 1RAID-0, I am unable to use the 320 GB drive as a system disk.

  If the original system drive is cloned on a new 320 GB drive, that it does not start. Starting XP * begins * but subsequently fails with STOP 0x7B - in other words, the infamous blue screen INACCESSIBLE_BOOT_DEVICE when the Toshiba RAID driver is loaded during Windows startup.
  Plain vanilla CD, of course with slipstreamed windows installation driver Toshiba, impossible rest. Installing Windows don't "see" drive in Bay 2.

  When the drive system is put in the high Bay and G20 is started from it, Windows XP starts correctly. The drive in Bay 1 is accessable from Windows, however, remains offline in the RAID from Toshiba console. If the start player in Bay 2 is not an option, too.

  A similar problem, where the owner could not install a system of 200 GB drive is described here
  Link: http://tinyurl.com/38wokw
  The owner, however managed to install a 100 GB drive and we have resorted to 80 GB of disk as a system disk and the only player upgrade in Bay 2 to 320 GB.

  I understand what happens when the disk is 'initialized' in the BIOS. Only brands of BIOS of Toshiba disk 1RAID-0, and it breaks down on 320 GB drive. I will refrain from expressing my opinion on this practice.

  My question is - if it is possible, how * manually * mark the drive of 320 GB 1RAID-0?
  Using a hex editor, dd or something similar is no problem. A partial answer would also know the disc more large size which * can * be marked with success under the name of 1RAID-0 at BIOS G20.

  Thanks in advance.

  Hello

  I m not 100% sure, what could be wrong by presumably 320 HARD drive size might be too big!
  How about the 100 GB or 120 GB hard drives?

  I think you should consider it because usually most of the BIOS supports a HARD drive size limitation and therefore not all sizes are supported.

  But note; using the configuration of 1RAID-0 (striping), met by the operating system size is twice more only if the smaller of the two HARD drives in RAID configuration. Using RAID-0, all data on both disks will be lost, even if it is training of two disks fails.

• Computer automatically restarts and the disk driver hard name question.

  Original title: my PC has 2 problems

  Hi guys, I'm going to talk about my PC has 2 problems.

  1. The problem is when I turn on my computer and boot my system, after 20 minutes I'm playing games, it auto restart my PC several times. 2 weeks ago, my old diet was very serious problem and the cause cannot start my PC, so I bought one to replace. Until a few days ago, it worked with my PC. He still now, have the same problem, but that sometimes he can't start several times and then she came back to do it again. I thought that it will more work and not a problem. I am very nervous and furious...! >:(
  2. Another problem is that my drive hard(location is C:\), it cannot load my system sometimes as the first problem earlier. Not only that, when it is started my PC, I checked all my hard drivesof driver name(I have 2 HARD drive, everything is very old)right click on C:\, click 'Properties' and then click 'Material' tag for the driver name lists. I don't see a single HARD drive driver name(it's in D:\), not on C:\ Name of the driver drive HARD, but in 'My Computer', it takes C:\ icon to click. I don't know why a few months ago, it has worked until now, one is missing and we're still on the list of driver name.

  Hope everyone give me help.

  Hi Billy,

   
  1. do you get an error message/code?
  2. What is the brand and model of the computer?
  3. How many partitions on each disk hard you?
   
  -For the first issue with computer restart automatically, follow the steps in method 3: disable automatic system failure reboot from the link:
  How to solve problems of hardware and software drivers Windows XP
  http://support.Microsoft.com/kb/322205#M3
   
  If the problem persists, see the event viewer for the detailed error message.
  Follow the link for the procedure:
  Procedure to view and manage event logs in Event Viewer in Windows XP
  http://support.Microsoft.com/kb/308427
   
  -For the second question, I suggest you to run a check disk and find if it helps.
  Reference:
  How to perform disk error checking in Windows XP
  http://support.Microsoft.com/kb/315265
  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.
   
  Also check if all of the hard drive and the drive letters are displayed correctly.
  Follow the steps to access disk management:
  a. click on Start and then run.
  b. type diskmgmt.msc in the text box and press the enter key or press the OK button.
   
  If the problem persists, you can write to us and we will be happy to help you further.

• I can't play discs or load programs on the disk, the disk drive does not work

  My disc drive won't play music discs, or program.

  Hi shaymoss,

  1 when was the last time it was working fine?

  2. did you of recent changes on the computer?

  3. what happens when you insert the disc in the drive?

  4. What is the number of the brand and model of the player?

  See the Microsoft article below and run them the fixit tool available, check if it works.

  Try the manual steps, mentioned in the article, if the fixit tool does not fix the problem.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Check the status of the disk on the computer by using the Device Manager and after return with details.

  How to solve the problems of hardware with Device Manager

  http://www.Microsoft.com/windowsxp/using/Setup/learnmore/devicemgr.mspx

• Dual Boot with windows XP Pro with 2 HARD drive, error on secondary windows install: "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check boot path and disk hardware... »

  Hi, I recently bought a new Hitachi 1 TB internal hard drive. I wanted to do a clean install on the new drive (d), be able to dual boot my computer and leave my old 300 GB disk (C :) as the primary windows installation. After physically installing the new HARD drive, I noticed that "new hardware found" and the the brand name flashed in the bottom right corner. I thought I'd see the new hard drive in my computer, but I did not. I initialized the new HARD drive with the computer management window (right click on my computer - manage) and I also formatted in NTFS (I had to change my printer hard drive letter to assign the new HARD drive with the letter D, but I've made other changes after this step). Now, I could see and use in my main windows on the C: installation. I then installed a windows new copy XP pro with the installation CD I got for my C: but on the D: (Note: I have a Dell computer (and the Dell reinstallation CD) and my current version of windows has SP3 while the installation CD is only SP2) (I also reformatted my HARD drive during the installation of windows to NTFS)

  Now when I try to start on installing the new on my D: I get "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check startup disk and hardware access path. "and another line saying to refer to manuals HARD drive and windows.

  My Boot.ini file at this time was:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (0) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I looked towards the top of this help page, but for now I'm unlucky:

  http://support.Microsoft.com/kb/314477

  (The next steps I took by throwing from the Windows CD and go into the repair console)

  I tried to use the bootcfg /rebuild but the line to boot.ini for my secondary HARD drive still does not work.

  He gave me something like:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (1) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I also tried to change the signature() to multi (0), but it did not work. (or try almost all possible permutations of disk() and rdisk() partition() 0 to 2).

  I also tried to use expand F(dvd-drive):\i386\ntkrnlmp(I_have_a_duo-core).ex_ D:\windows\system32\ntoskrnl.exe and a few other combinations, but I when I login as D:\windows simply, it fails to extend with a message like "could not develop" or C:\windows I get "restricted access".

  I have not yet tried CHKDSK/r, but since I did a clean install on a newly formatted drive... I don't think it would work.

  I've also marked the partition on the D: as active (in computer management), but it did not help me.

  I've done a first installation of windows repair, strangely, I couldn't fix this one... Still does not work...

  My default windows installation yet works very well & I see that windows has been installed on the D: but I'm ideas from how to operate the dual-boot, can someone throw me a BONE on what to do?

  Maybe try to do something with the Boot Manager (whatever it is?) Create a new partition and use it as a boot manager? I don't really want to do this, because if I made a mistake I will be unable to use my computer and dual boot should work without going through all this trouble... But I found this page: http://technet.microsoft.com/fr-fr/library/ee829686%28WS.10%29.aspx

  Could a clean install two HDD help? I hope I won't have to do...

  Someone has an idea?

  PS: I'm not such an advanced user so I need a solution step by step, thanks!

  Edit: I also noted that I can't see my new HARD drive in my BIOS... weird... SATA-0 is my old drive HARD 1 and 2 are my dvd 3-5 readers are 'off' and it doesn't seem to be anything that it is plugged in. I also have 4 bays for internal HARD disks. Now, 2 are busy.

  Edit2: I looked inside my case and enabled the good Sata in the Bios after a reboot it detected the drive correctly. Dual boot doesn't always work well... The fact that it was disable in the BIOS while I was installing the new HARD drive could change anything? Hmm...

  In case I wasn't clear enough: I had a windows XP Pro installed on my C:, bought a new hard drive and installed the same copy of windows on it (d). I think that should allow me to double boot between the two installs different. Even if for some reason I can't boot from one on my D:. Andrew, I do not understand why you so far physically disconnect the other drive, the point of the whole operation is to build a boot.ini file so that the BIOS knows that it y facilities 2 windows and you allow to choose (and not have conflicting problems between the 2 systems), someone correct me if I'm wrong? "Expand" the part of my first post made reference to one of the solutions provided by Microsoft in the first link that I have included in my previous post (but I can't seem to work).

  In addition, it is the procedure that I followed: http://www.ehow.com/how_5950826_boot-two-different-hard-drives.html

  (except I've had the first installation already done).

  Andrew "also, once a new hd is plugged on the pc & running, most of the BIOS will place (them) as 1st priority hd, set the BIOS to do this", you mean that by installing separately from windows on each unit when the other is not plugged in, I could choose what disk to start from defining their priority in the BIOS once they are all plugged back? It's too tedious (as I intend to move frequently between the 2 installs) and requires a computer to other users of the lack of computer knowledge. Unfortunately, it is not a viable option.

  EDIT: I DID IT! Hmmm... Well, I double checked in the recovery console, the path of the new HARD drive with the arc command Scan. Tried to start again with the MULTI (0) in my boot.ini and it worked... I also had my windows install CD in. Maybe that is why I could not start, windows needs the CD to complete the installation? Weird, I don't know what I did to the difficulty it... but hey, it works! Thanks for your ideas guys!

• just has got rid of the virus and responsible for all the disks but given the wifi does not work

  WiFi doesn't work do not

  just has got rid of the virus and responsible for all the disks but given the wifi does not work

  Hello

  Check with the system manufacturer or the actual WiFi device manufacturer and ask in their forums (if any)
  for problems known.

  Actually, try updating your driver:

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Windows start error. Root cause: no OS file found on the disk.

  My computer shows a blue screen all of a sudden, but I can't capture it. Then when it restarts, it entered the Startup Repair and it performs some tests, the other components is good but at the bottom of the diagnostic and repair details it says this:

  Root cause found:

  ---------------------------

  No OS found on the disk file.

  Repair action: Partition table repair

  Result: failed. Error code = 0 x 3

  Time taken = 6053ms

  ---------------------------

  ---------------------------

  While in the result of the diagnosis
  It shows:
  [Suspected party troubled] Hard drive
  [Error code] 2109

  Hard drive may have a hardware problem
  Please contact the Service Centre

  Can I find out if there is no possible solution to fix it and recover the data?

  Hello

  Go to the website of your computer manufacturer > search your computer specifications > know brand of hard drive > access the Hard Drive manufacturer's Web site > find and download hard drive Diagnostic software and make a record of start of it on the computer that you use to get here, following their instructions > test your hard drive to see if it has failed.

  And you can also use this method to test your hard drive:

  "SeaTools for DOS.

  http://www.Seagate.com/support/downloads/SeaTools/

  "SeaTools for BACK tutorial.

  http://knowledge.Seagate.com/articles/en_US/FAQ/201271en

  ________________________________

  And how do you try to back up your data.

  Saving your files:

  You can remove the hard drive and put it in a hard drive USB enclosure > plug it into another computer > and try to read and copy your data in this way.

  Or, you can download Knoppix > make a bootdisk to > start your system with it (IF your material is all work) > and copy your data from the hard drive like that.

  http://Knoppix.NET/

  "How to use Knoppix.

  http://Lifehacker.com/192982/geek-to-live--rescue-files-with-a-boot-CD

  See you soon.

• Download black screen during installation of Windows 7 from the disk.

  Original title: loading Windows 7 with windows 8 is already installed

  Dell computer brand new.  (Terrible dealer. They charge $ for help on something other than the material.)  The new computer comes with windows 8 is installed.

  Like any windows 8.  Ordinate of windows 7.  They sent the disc and no key.

  Dell will not help with installation unless you pay them $!  They say that it's a Microsoft product, and they are not obliged to help, even if it was purchased from them!  It's like buying a new washing machine or a car.  You need to contact the manufacture to get help with it?

  No, you communicate with the store, it was purchased from.  This applies to any new product I know. But not with Dell!

  Sorry for the rant.  I just found this totally outrageous situation.

  MY PROBLEM:

  Installing windows 7 from the drive, they sent.  Ten minutes into it the screen goes all black.  It is said that there is a file on the disk.  Also a button to continue.

  I stopped the installation and am at a loss as what to do...

  Thank you, Al

  Hello

  Have you checked to see if your model computer has Windows 7 drivers available from Dell for it?

  If not, it will not install properly or work properly.

  Dell:

  http://www.Dell.com/support/drivers/us/en/19/ProductSelector

  ___________________________________

  Have you changed the order of startup and boot the Windows 7 disc, they sent you?

  You press F12 in a Dell to change the Boot order

  http://en.community.Dell.com/support-forums/desktop/f/3514/t/19500812.aspx

  Then do a clean install:

  http://www.SevenForums.com/tutorials/1649-clean-install-Windows-7-a.html

  ____________________________________

  Or ask Dell to replace the disc if it is faulty.

  ____________________________________

  Or download the correct ISO file and make your own drive and use the product key that is on the sticker COST Dell sent you.

  http://www.w7forums.com/threads/official-Windows-7-SP1-ISO-image-downloads.12325/page-2#post-124821

  And Neosmart has instructions on how to burn ISO disk images using imgburn:

  http://NeoSmart.NET/wiki/Burning-ISO-images-with-ImgBurn/

  By using the downloaded ISO file method can require the Activation of phone.

  If it does require phone activation, do not follow Demand of Auto, but brace yourself for a real person explain as to what has been done for purposes of re-setup

  "How to activate Windows 7 by phone '

  http://www.SevenForums.com/tutorials/18715-activate-Windows-7-phone.html

  The above method also requires that you go to your computer manufacturer's website > Support and downloads Section > locate your model number and operating system > then download and install the latest drivers for it.

   

  ________________________________________________

  Using the method of USB in conjunction with the Windows 7 download preceding:

  http://www.SevenForums.com/tutorials/2432-USB-Windows-7-installation-key-drive-create.html

  "How to get and use the Windows 7 USB/DVD Download Tool"

  http://www.SevenForums.com/tutorials/31541-Windows-7-USB-DVD-download-tool.html

  See you soon.

• Windows could not start... I need the disk installation?

  Hi, so I recently uninstalled Windows 7 by accident... And I tried to make it work, but it won't, so I need the disk. I contacted microsoft asking if I can get another disc or something. And they said to go to m6mobile.fr. So I went on it, got the Windows 7 USB/DVD download tool, I got the ISO file on my USB key. And now I have everything. So I took out the laptop I did all the stuff on, I then went to the computer to install Windows 7. And it still does not work! I plugged the USB with the ISO file and then restarted, and it still doesn't work? Can someone help me? I stayed until 02:00 am trying to solve this problem!

  Thank you! Here's what the problem...

  (Sorry for the small image!)

  

  Your problem is the link below:
  http://www.SevenForums.com/BSOD-help-support/209281-boot-manager-status-0xc000000f-boot-selection-failed.html

  What is your computer brand and model?

• C200 M2 LFF does not see the disks in the start menu after installing ESXi

  So in front of me, I have a brand new C200 M2 LFF with a single E5606 processor, 20 GB of RAM and a controller LSI Megaraid 9260 - 4i and 4 drives of 1 TB SAS. I put the disks in a RAID 5 array, I created a 10 GB virtual disk and properly installed ESXi on it twice, with a second virtual disk to be used as a data store.

  However, I can't get the thing to boot. It isn't even an option. The only storage in the boot menu option corresponds to the DVD player. If I look at the mass storage controller configuration, in fact, 0 and 4 SATA ports are "not installed" and port 5 has the DVD player.

  I tried fiddling with the settings of the BIOS without a bit of luck. Currently, the integrated controller is enabled and the SATA mode is set on improved (which seems to be the default, and what is recommended with Megaraid cards). It is a bundle (UCSC-DBUN-C200-102 by delivery, which seems to be a number of separate reference only), so I didn't have to assemble whatever it is and I guess that all the cables are connected at the factory. I opened the server, and I can say that all the cables look connected.

  Any suggestions? Any help would be greatly appreciated. If I have to open a case with the TAC, that's good, but seeing as I can't actually install the operating system there must be something stupid miss me.

  Disable the onboard Controller. This is software raid ICH10R.

  Reset. Then in the fixed CIMC/BIOS boot order and pint at the LSI.

  For the most recent ESXi 5.0, go to VMWare and search for ' ESXi 5.0 cumulative 2.

  Sent by Cisco Support technique iPhone App

• Windows media player encountered a problem burning the file on the disk

  What does that mean? Im trying to burn music to a disk and keep getting this msg... HELP... windows media player encountered a problem burning the file on the disk

  Hi michealarthur,

  Here are a few things to try:

  1. make sure that the disc is clean.

  2. Select a recording speed (write) more slow for the CD burner.

  3. try a different brand of blank discs.

  4. stop all other programs that are running.

  5 disable any programs that could activate themselves, while burning is in progress, such as screensavers or anti-virus programs.

  6. defragment your hard drive.

  7. make sure that the hard drive does not use disk compression.

  Change settings for burning a CD or DVD in Windows Media Player

  http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-burning-a-CD-or-DVD-in-Windows-Media-Player

  Also...

  You can try this procedure to restore your windows media player.

  (1) Perform SFC first. Follow the link on how to make SFC (http://support.microsoft.com/kb/929833)

  (2) turn on / off Windows Media Player again.

  a. go to start and in the search type 'Turn Windows has or not'.

  b. click on the "Turn Windows features on or off".

  c. check the "media features.

  d. restart the computer.

  You can also try restore (http://windows.microsoft.com/en-us/windows7/products/features/system-restore) your computer to the final point where windows media player worked.

  Or you can use the previous versions of windows media player that comes from restore points or windows backup.

  Or you can try to run 'Fixit '.

  http://support.Microsoft.com/mats/windows_media_player_diagnostic/

• cannot select the disk to install the update of the Sierra (Macbook Pro 13 inch, late 2011)

  I downloaded the update of the Sierra and proceeded with the installation. However, I noticed that even if I could move the pointer autour, I couldn't make selections on tapping the trackpad. I managed to get past the first steps by using the 'tab' key (keyboard) to make selections and 'space' to make the confirmations. However, arriving at step 'select the disk where you want to install Mac OS', the 'Tab' and 'Space' technical has stopped working. Now I'm stuck here. Can someone tell me please how to go beyond this?

  Looks like it's a problem of trackpad? Or in any case a trackpad issue connected with installation of Sierra? I would take the MBP for a Genius Bar...

• On the utility of record pass-protected when the disk is encrypted

  Dear all,

  I recently put my hands on a new internal drive SSHD and decided to quantify using filevault. Keep important documents on my mac, I used to create folders of password-protected using a disk with disk utility image. Now, my question is simple: is there a utility on the creation of these encrypted files as all the disk itself is already encrypted? This would add valuable new protection?

  Thank you very much in advance,

  Richard

  Data sheet: mid - 09 13 MBP "2.26 GHz with internal WD 1 TB SSHD

  If your disc is encrypted, then the only way that anyone (including YOU) can look at the contents of your Volume is to provide your password to disk, which we hope is a long and strong password, not only a short practice. Depending on how paranoid you are, perhaps you fell there is additional value on encryption more away from the additional items. But for extra security, the password for your encrypted disks in addition should not be readily available on your drive any just-encypted.

  Most users have very good success with encrypted Volumes. They manage to protect their records from the person mostly likely to access - themselves. DO NOT ENCRYPT YOUR DRIVE WITHOUT CREATING A RELIABLE BACKUP! The encryption is strong - there is no 'rescue' for an encrypted Volume that goes wrong for any reason, including failure of the drive.

• How can I just disable logging in El Capitan? It is not visible in the disk utility by pressing alt and file!

  How can I just disable logging in El Capitan? It is not visible in the disk utility when you press alt and file!

  

  Mac OS X: about the logging of system - Apple Support files

  Hope this helps, good luck to you.