No connectivity with Z5 Premium LTE network

Similar Questions

• WRTP54G (wireless router with phone connection) with Panasonic BL-C30A network camera (WEP only)

  Hello

  I would use this wireless router with WEP I can access the wireless camera (camera does only WEP encryption).
  The camera should be the only device authorized to connect to this wireless router.
  I can devote channel 11, so only use this wireless router
  I know that WEP can be cracked but I think maybe I can set up the router for it does not matter, i.e.,.
  While the camera is accessible by this particular router

  so my questions are:
  1. can I configure the router so only local outgoing LAN requests http are allowed?
  2. any other suggestions about the configuration of router that prevent access to my network?
  (using address filtering (by address mac camera only) MAC is worth, but I guess that the MAC address can be spoofed so not a complete solution)

  Thank you
  Tom

  I think that 'toomanydonuts' has provided my solution in this thread:

  solution wire

  Thank you

  Tom

• locked settings by the adiministrator system and unable to connect with the new wireless network

  I changed my ISP and routers.  I need to change the settings to the new router wireless.  However, when I try to access the network settings on the printer through the screen on the printer, it is said that it is locked by the system administrator.  I am the admin.  Where can I access it without being on the network?  I tried to reset to the default values of factpry, but the same problem exists; It is blocked by the system administrator.

  I was able to solve the problem.  I went through the set up using the USB cord.  Then I switched it to wireless technology.

• In a roaming network, Mac always connects with AE which is further away

  So, I had a roaming network for years to host a detached office which was too far from my house.  Worked very well.  Now, my family and I have moved into a temporary rented condo (two floors).  Therefore, there is a lot of wifi networks in the area in conflict with.

  After trying to extend the network (signal too low in the area), I decided to try the roaming network again.  Most of the time, it works very well.  But from time to time, my iMac (on the ground floor) connects with the Airport Extreme, which is on the floor instead of the Airport Express, which is down in the same room as the iMac.  What happens when it connects to the Airport Extreme on the floor, my Tx rate drops to less than 100 Mbps (sometimes dramatically if) and I am unable to listen to the music to my Airport Express without dropouts.

  The dressing was to turn off my wifi on the iMac, and then turn it back on.  It will then connect to the Airport Express.   The problem is that I have to do this in general once a day as my iMac will enter into the "standby" and periodically reconnect with Airport Extreme when I wake up (or if I re-enable it if off).  Ideally, he would stay with the Airport Express.

  So I hope that there is an alternative.  I thought about simply renaming the Airport Express network in the different name of Airport Extreme.  But all the itinerant instructions whereby I know that network names must be the same for all airports in the roaming network.  But perhaps this is not the case.

  Comments are appreciated!

  Unfortunately, you encounter a known issue with the use of a roaming network... and it is not specific to those provided by Apple either. The "solution" you use, although not elegant, is basically everything with that we have (at this time) to go.

  In theory, your iMac fixed, must always connect to the Wi - Fi with the signal network hard... not necessarily the closest to it. It may be possible, since you mentioned that you live in a highly congested environment Wi - Fi, your iMac is struggling to determine the right network to connect to when starting.

  Of course, a more "permanent" solution for your iMac, at least, would connect directly to the nearest base by Ethernet station.

• The local network settings for arbitrarily lose connectivity with ADSL modem

  Hi all

  I have a SAGEM 1500WG ADSL modem for internet connection and a laptop Satellite A100 (PSAA9). I noticed that arbitrarily, the ALARM led on the modem of DSL connection worked again (according to the lights on the modem) and the real problem was that I couldn't ping my modem. The problem was inside my local network. I can't be sure that what happened outside my LAN because I could not reach even the modem.

  The only solution is to reset the modem. After 4-5 months of use, I have concluded that, whenever this was happening, I used Azureus to download a movie and this download was pretty slow (for example because my counterpart have fast connection). Also, I was connected with wire and NOT using the modem wireless. This means that: the problem never appeared when the wireless or Azureus works and download a significant amount of data.

  I wonder if the LAN driver has any firewall installed on it. Or if she has any function that transforms the power driver LAN offshore when there are very few or no data go through it for a certain period of time.

  Or East-Azureus has any odd décor that reminds you of something above?
  The combination I think is problematic is "adapter LAN + Azureus work + very little data being downloaded. Maybe I'm a little confused. Anyone who has experienced the same problem or can come up with an idea will be extremely useful.
  Thank you very much.
  Lambros

  Hello

  Don t think that there is a problem with the LAN settings or the LAN driver on the device!
  Your data transmission to low and transfer depends on your service provider Internet (ISP) and the server.
  Your Azureus application does not for me, but in my easy it s a transfer of connection and the data of the software simply PEAR-pear file also depends on the number of users and the connected clients

• At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  At my place of work, there are a data server with LAN and internet networking. I want to disable the internet connection before it is infected with the virus.

  original title: server and virus problem

  Hi SurajMendon,

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the platform of networking on TechNet. Please post your question in the TechNet Windows XP Networking forum.

  Networking platform

  http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads

• Internet connection with Windows XP, SP3 and Airport Extreme - the status is always "absorbing network address.

  My Airport Extreme connected my IMac immediately, but I am not able to connect on the side PC. Airport utility does not 'no matter what Airport wireless devices". When you check the status of the internet connection with PC tools, the correct network is indicated and shows an excellent signal strength. The status is: "absorbing the network address. However, nothing happens.

  Under 'Repair the wireless network connection', it shows, "Windows is taking the following steps: your IP address renewal" even once, nothing happens.

  Under hardware I show Atheros Wireless Network Adapter and the mention: "this device works correctly.

  Yet, no network connection. Any help will be greatly appreciated.

  Hello

  Keep the changes and open the wireless. For example, to disable security in the router (turn on when to managed to connect).

  You can also try the wireless in a friends house, or an Internet café to get a frame of reference for this behavior elsewhere.

  -------------------

  Wi - Fi in general.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled).

  If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Office jet pro 8600 connect with router but not recognized on the network

  I just installed new router e1200 lonksys. JO HP 8600 pro connects with the router, but the printer cannot see 8600. IP 169.254.223.37 on said install ip is the placeholder and printer not connected. have restarted once 1000 and tried to reconnect. New router has OMP and thrust of 3 seconds the button on the router. Also failed to connect on the router definition reviews

  8600 worked fine on the old router. Problem started when I connected the router after that cable modem connected then modem vonage. Previous setting was cable - vonanage and wireless router - all worked well then.

  Also downloaded 8600 new complete software after losing the Wi - Fi connection - please help!

  If the Ethernet cable is plugged into the printer, it will disable the wireless radio.

  If this is not the case in the network menu, network by default.  Then, in the same network menu, run the Wireless Setup Wizard.

  If this does not work, we will come on your new router a bit.

• Loss of connection with my router, shows only limited access and my network showed that unidentified

  Original title: unidentified network, missing the default gateway

  Hello

  So one day out of the blue I lost connection with my router. I was able to reconnect but this time around I had only limited access and my network showed non-identified. I tried to connect to a different wireless network, same thing. When I run ipconfig, I'm missing a value for the default gateway.

  I tried to:

  -Reinstall the drivers for the adapter

  -update the drivers

  -Reset my router

  -Gateway ipv4 manually of entry

  -kill lan via Device Manager drivers

  -scream at the computer

  I have a Setup to dual boot with Linux Mint along side Windows 7. When I boot in Linux it connects to any network without problem.

  Some help would be appreciated.

  Plug

  Windows 7 Ultlimate

  I7-4700MQ @2.4

  GTX 765M 2 GB

  8 GB RAM

  1 TB + 240SSD

  Realtek RTL8188CE wireless

  Hello Alex,.

  Thank you for your response.

  I appreciate your time.

  I suggest you to uninstall the network driver wireless and reinstall in compatibility mode.

  To uninstall the driver, follow these steps:

  a. press Windows + R keys together, type devmgmt.msc in the run window and press ENTER.

  b. Click to expand network adapters, right-click on the map and click Uninstall.

  c. restart the computer.

  Now you can Download driver from this link wireless.
  Reference:
  http://downloads.Eurocom.com/support/drivers/zip/238/238_RealtekWLAN_W764.zip

  For reference:
  EC http://www.Eurocom.com/EC/drivers (238)

  To reinstall the driver in compatibility mode, follow these steps:

  a. right click the driver file, and then click Properties.

  b. click on the compatibility tab.

  c. click on check "run this program in compatibility mode for" and select Windows XP(Service pack 3).

  d. click apply and ok.

  Now, install the driver.

  Please keep us updated.

  Thank you

• I just changed my internet provider and can connect with two of our cell phones, but the third said no identified network/no access to the internet.

  I just changed my internet provider and can connect with two of our cell phones, but the third said no identified network/no access to the internet.  I tried all of the obvious solutions.  Windows 7

  Original title: unidentified network

  Hello

  Thanks for choosing Windows and thank you for providing an opportunity to help you.

  According to the description, you are having problems with the unidentified network error message.

  Perform the steps from the link below and see if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/network-connection-shows-that-it-is-connected-but/52e60042-2666-4EAF-80be-193b26db10be

  Answer to us if you are having problems with the unidentified network or any other issue of Windows, and we would be happy to help you.

  Good day!

  Hope this information helps.

• Wireless network connection is connected with the strong signal, but stops working at random times

  Original title: internet says is connected with the strong signal, but stops working at random times?

  Hello
  For the last few weeks, I had problems with my internet connection. Wireless connections say I am connected and have the strength of the excellent signal. I know that this is not an ISP problem because my other computer works fine. I will be reviewed fine and then all of a sudden, the site doesn't load any more, although I'm always connected to the internet. This happens on Firefox and Internet Explorer, this isn't a browser issue.

  I read other offered on the internet and tried all, but nothing has changed. I have checked proxies, disabled antivirus and installed new, checked firewall, ran a check for malware, etc..

  Any help will be much appreciated because it becomes very frustrating to have to keep reconnected my internet when he says he's working.

  Hello

  I suggest you follow the links below and check them with the question:

  Method 1:

  Step 1:

  Start your computer in safe mode with network and check the number: http://windows.microsoft.com/en-US/windows7/Advanced-startup-options-including-safe-mode

  Step 2:

  You need perform a clean boot to prevent any third party conflicting application from interfering with your computer.

  To put the computer in a clean boot State, you must follow the steps in the article mentioned below and check with the question.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: You must follow step 7 of the article mentioned above to recover your computer to a Normal startup after you complete all the steps.

  Method 2:

  Uninstall and reinstall the NIC drivers and check with the question.

  a. click on Start menu, in the Search tab type devmgmt.msc and press ENTER.

  b. right click on network adapters, and then click on uninstall and restart the computer.

  c. after rebooting, install network cards and check with the question.

  For reference:

  How can I troubleshoot network card? :

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

  I hope this helps.

• Error "no network access" on the devices not connected with hotspot Wi - Fi on Windows 8

  Original title: wifi hotspot problem not reciving data connected network - windows 8

  I have windows 8 simple ASP, when I do a WiFi hotspot it activate and connected to the iphone, lumia or tab, but the data are not recived by any device? they don't show error no network access? What is the problem?

  Hello Anwar,

  I wish to gather information to help you better:
  (1) where exactly you receive the error message "no network access? It's on the phone or the computer?
  (2) how do you have enabled connection with devices Wi - Fi hotspot?
  (3) you have problems connecting Wi - Fi hotspot on the computer?

  (4) you receive the same error message with all devices?

  If the issue is with Windows phone, post the same question in the forums Windows Phone for assistance. Check out the link:

  http://answers.Microsoft.com/en-us/WinPhone

  If you encounter this problem only with the computer, then respond with more information so that we could help you better.

  Answer us with more information that would help us resolve this problem more far.

• wireless connection with the unidentified network

  Hello

  I have recently moved house and who to connect my computer to the wireless network that we installed. He works to connect said however that the network is 'unidentified' and I can't connect to the internet. I tried to diagnose the problem, but nothing seems to work. There is nothing wrong with the router, because it works with all other computers in the House except our HP computers two and it works whenever I connect with the cable, but not wifi.

  I've had the laptop for about 5 years now.

  Computer: HP Pavilion DV6824eo PC entertainment network

  Operating system: Windows Vista 32-bit

  I would be very happy if someone could help me with this!

  Lovisa

  I managed to fix everything at the time, had to download the latest version of the WLAN ahteros driver.

  Thank you very much!

• I am connected with the nearby ethernet cable but I can't connect to the network.

  I connected with the surroundings but ICAN t ethernet cable get internet

  Hello

  1. what operating system is installed on your computer?
  2. What is the error message when you try to connect to the Internet?
  3. don't you make changes to your computer before the problem?

  Search for related errors in the event viewer.

  Follow the steps in this article if you are using Windows 7.

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

• C7180 HP printer goes offline when it is connected with the wireless network

  Hello

  I have a problem which seems to be common, but I can't find a solution simple 'step by step'.  So my apologies in advance for you who are technically much more advanced that I am and know that this has already been answered.

  I have a sony vaio laptop running Windows 7.  At home, I have a printer all-in-one HP C7180 I connected wireless on my home network.  FYI, I have a netgear wireless router.

  Once I have installed the printer on the network, everything works fine until I closed my computer.  On restarting, the printer is detected as offline by my laptop.  Now, my solution is to uninstall the printer and reinstall it.

  If someone would be kind enough to give a detailed set of step by step instructions on how to solve this problem, it would be much appreciated.  I read on the definition of a static IP address rather than dynamic, but I would need one together instructions if this is indeed the way to go.

  Thank you.

  Rich - desperate to finally solve this nuisance.

  Hi rich,

  As you mentioned that the printer goes offline after a reboot, please refer to:

  "Printer is off-line" Message appears on the computer and the HP printer does not print