No interface BVI?

Similar Questions

• Speed limit on BVI Interface (ASR9001) - several customers

  Hello world

  I was wondering if someone might be able to shed light on what I'm missing to get the following upward and running for one of our customers.

  Scenario: Customer has an ASR9001-S, that makes all the routing as the basis for their internet business customers and they are trying to evaluate limit each client to their respective SLAS. All clients belong to a single instance BVI (BVI200) for example which has a configured 25. Each customer will receive 1-3 25 addresses.

  Ideally, I would have a BVI for each customer, but unfortunately, this is not possible with their IPv4 currently the allowance which is the reason why he's built in this way.

  I was thinking about the following, but I got some errors when I apply the strategy of service for the British Virgin Islands.

  Comment by Customer_A-v4_10Mbps-list of access IPv4 * IPv4 client A 10 Mbps symmetrical Service *.
  Access Customer_A-v4_10Mbps IPv4-list allow ipv4 a.b.c.d/32 one
  !
  Comment of Customer_A-v6_10Mbps-IPv6 access list * customer A IPv6 10Mbits/s symmetric Service *.
  IPv6 Customer_B-v6_10Mbps allowed x ipv6 access list: x: x: x: / 64
  !
  Comment by Customer_B-v4_20Mbps-IPv4 access list * client B IPv4 20Mbps symmetrical Service *.
  IPv4-Customer_B-v4_20Mbps access list allow ipv4 e.f.h.i/32 one
  !
  Comment by Customer_B-v6_20Mbps-IPv6 access list * client B IPv6 20Mbps symmetrical Service *.
  IPv6 Customer_B-v6_20Mbps allowed x ipv6 access list: x: x: x: / 64
  !

  class-map correspondence-everything Customer_B_10Mbps
  game group-access ipv4 Customer_B-v4_10Mbps
  ipv6 Customer_B-v6_10Mbps group-access game
  end-class-map
  !
  class-map correspondence-everything Customer_B_20Mbps
  game group-access ipv4 Customer_B-v4_20Mbps
  ipv6 Customer_B-v6_20Mbps group-access game
  end-class-map
  !

  Policy-map Business_Internet
  class Customer_A_10Mbps
  form average 10 Mbps
  10 Mbps bandwidth
  !
  class Customer_B_20Mbps
  form average 20 Mbps
  20 Mbps bandwidth
  !
  class class by default
  form average 5 Mbps
  bandwidth 5 Mbit/s
  !

  I also tried to create with a parent/child policy-map, but I get the same errors listed below:

  interface BVI200
  service-policy output Business_Internet
  !! QoS-% "ea" detected the condition 'Warning' "actions of queues are not supported on virtual interface BVI/GRE"
  !

  interface BVI200
  Business_Internet of service-policy input
  !! QoS-% "ea" detected the 'Warning' status ' characteristics of queues of penetration is not supported on this card online.
  !

  A that someone does something similar to this. Unfortunately, this will be a dynamic policy-map that will grow/shrink as clients are added/removed.

  I am also looking to apply the formatting on the client side port, however there will be some cases where this is not possible due to multiple clients of services by a switch single demarc...

  Thoughts/Comments/Suggestions.

  Thank you.

  -Dominique

  Hi Dominique,.

  have you tried with the police instead of formatting? Shaping on BVI intf is not supported.

  I remember that we tried to do some police on a Trident LC services and it was not taken in charge, as the Typhoon. ASR9001-S has Typhoon HW (Enhanced Ethernet line card) until now I know.

  You can also try this link. I remember that we had to use qos-group even on ME3600 due to some HW limitations.

  http://www.Cisco.com/c/en/us/TD/docs/routers/asr9000/software/asr9k_r5-2...

  ' Queuing can be done by marking the qos-Group, then by adding a policy to the interface that corresponds to the qos-Group. "

• Unique SSID to the autonomous access point

  Hello

  My question is that if I have one SSID on an autonomous access point while I use the vlan native too. I mean what's the best practice in this case, if the vlan wireless say 10.

  Also I have to use the bvi-1 or I have to creat bvi another for this vlan?

  Thank you

  In my experience it's not a must to use native vlan.

  No, you should use only one interface BVI.

  Just like that:

  Ter of conf
  !
  Dot11 ssid ABC
  VLAN 10
  Open authentication
  Authentication-key wpa version2 management
  WPA - psk ascii cisco123
  Comments-mode
  !
  d0 IND
  SSID ABC
  encryption aes encryption vlan 10
  !
  D1 IND
  SSID ABC
  encryption aes encryption vlan 20
  !
  d0.10 IND
  encapsulation dot1q 10
  !
  D1.10 IND
  encapsulation dot1q 10
  !
  gig0.10 IND
  encapsulation dot1q 10
  !
  int bvi1
  IP address

  Concerning

  Remember messages useful rates

• 871 wireless configuration

  I'm trying to get a router 871 soho wireless connection to work.

  The SDM is useless.

  I tried to find documents on how and why and what to do - but no luck.

  Since this week. The DSL parts and fw works, but do not

  Wireless.

  I have a setup of open authentication - comments-mode activated.

  So I should be pretty wide open for connections.

  I can see the SSID on a client PC, but cannot connect.

  I use DHCP clients

  --------------------

  config below

  --------------------

  Bridge IRB

  !

  interface FastEthernet4

  Description $$$ FW_OUTSIDE$ $ES_WAN$ ETH - WAN

  no ip address

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  route IP cache flow

  automatic duplex

  automatic speed

  enable PPPoE

  PPPoE-client dial-pool-number 1

  No cdp enable

  !

  interface Dot11Radio0

  no ip address

  !

  SSID 1138

  VLAN 1

  open authentication

  Comments-mode

  !

  Speed of the basic - 1.0 2.0 - basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0

  48.0 54.0

  root of station-role

  No cdp enable

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  !

  interface Vlan1

  Description $ETH - SW - LAUNCH, INTF-INFO-HWIC $$ $4ESW $FW_INSIDE$

  IP 192.168.0.109 255.255.255.0

  IP access-group 102 to

  IP nat inside

  IP virtual-reassembly

  !

  interface Dialer1

  Description $FW_OUTSIDE$

  MTU 1492

  the negotiated IP address

  IP access-group 103 to

  inspect the DEFAULT100 over IP

  NAT outside IP

  IP virtual-reassembly

  encapsulation ppp

  Dialer pool 1

  No cdp enable

  PPP authentication pap callin

  PPP pap sent-username [email protected] / * / password xxx

  PPP ipcp dns request accept

  !

  IP classless

  IP route 0.0.0.0 0.0.0.0 Dialer1

  !

  IP http timeout policy slowed 5 life 86400 request 10000

  the IP nat inside source 1 list overload of the Dialer1 interface

  !

  recording of debug trap

  Note access-list 1 INSIDE_IF = BVI1

  Remark SDM_ACL category of access list 1 = 2

  access-list 1 permit 192.168.0.0 0.0.0.255

  Access-list 100 remark generated automatically by the configuration of the firewall Cisco SDM Express

  Access-list 100 = 1 SDM_ACL category note

  access-list 100 deny ip 255.255.255.255 host everything

  access-list 100 deny ip 127.0.0.0 0.255.255.255 everything

  access ip-list 100 permit a whole

  Access-list 101 remark generated automatically by the configuration of the firewall Cisco SDM Express

  Note access-list 101 = 1 SDM_ACL category

  access-list 101 deny ip 192.168.0.0 0.0.0.255 any

  access-list 101 permit icmp any any echo response

  access-list 101 permit icmp any one time exceed

  access-list 101 permit everything all unreachable icmp

  access-list 101 deny ip 10.0.0.0 0.255.255.255 everything

  access-list 101 deny ip 172.16.0.0 0.15.255.255 all

  access-list 101 deny ip 192.168.0.0 0.0.255.255 everything

  access-list 101 deny ip 127.0.0.0 0.255.255.255 everything

  access-list 101 deny ip 255.255.255.255 host everything

  access-list 101 deny host ip 0.0.0.0 everything

  access-list 101 deny ip any one

  access-list 102 remark self-generated by the configuration of the firewall SDM

  Note access-list 102 SDM_ACL category = 1

  access-list 102 refuse host ip 255.255.255.255 everything

  access-list 102 deny ip 127.0.0.0 0.255.255.255 everything

  access ip-list 102 permit a whole

  access-list 103 note self-generated by the configuration of the firewall SDM

  Note access-list 103 SDM_ACL category = 1

  access-list 103 deny ip 192.168.0.0 0.0.0.255 any

  access-list 103 permit icmp any any echo response

  access-list 103 allow icmp all once exceed

  access-list 103 allow all unreachable icmp

  access-list 103 deny ip 10.0.0.0 0.255.255.255 everything

  access-list 103 deny ip 172.16.0.0 0.15.255.255 all

  access-list 103 deny ip 192.168.0.0 0.0.255.255 everything

  access-list 103 deny ip 127.0.0.0 0.255.255.255 everything

  access-list 103 refuse host ip 255.255.255.255 everything

  access-list 103 refuse host ip 0.0.0.0 everything

  access-list 103 deny ip any any newspaper

  Dialer-list 1 ip protocol allow

  not run cdp

  !

  control plan

  !

  Bridge Protocol ieee 1

  1 channel ip bridge

  !

  max-task-time 5000 Planner

  Scheduler allocate 4000 1000

  Scheduler interval 500

  end

  interface Dot11Radio0

  no ip address

  !

  SSID 1138

  No vlan 1

  !

  interface Vlan1

  no address ip 192.168.0.109 255.255.255.0

  no nat inside ip

  Bridge-Group 1

  !

  interface BVI 1

  IP 192.168.0.109 255.255.255.0

  IP nat inside

  !

  end

  Cut these commands. I'm going to assume that if you make to a server and not the router DHCP. If you want to use the router, you will need to configure a DHCP pool.

• SF 300

  Friend of Delmas

  I knocked in certain configuration of my network.  I have two switches sf300 and cisco router 827.  In fact sf300 supports dhcp server.  I took cisco 827 as dhcp server and I create 4 pools dhcp in it.

  How do I configure in sf300 to service dhcp of the router cisco 827.  ISIT possible to configure 827 with interface bvi, when I try, I got error below.  Can someone help me configure the bvi interface and I'll link this bvi to vlan on sf300.

  error in 827 router

  Router (config-subif) #bridge - Group 1

  The bypass on a subinterface LAN requires that the interface already
  configured encapsulation Inter Switch Link (ISL) or 802. 1 q encapsulation

  SF300 Configuration:

  Int vlan 1

  IP 192.168.1.1 255.255.255.0

  int vlan 2

  IP 192.168.2.1 255.255.255.0

  int vlan 3

  address 192.168.3.1 IP 255.255.255.0

  int vlan 4

  192.168.4.1 IP address 255.255.255.0

  How can I connect two switch sf300 for redundancy?  I connected giga4 SW1 and SW2 giga4 mode trunk isit good or in any other way, I need to connect. ?

  Thanks in advance.

  Hi SIR,

  You must have the correctly configured DHCP relay

  Configure the terminal

  activate a dhcp IP Relay

  IP address of relay dhcp (DHCP server address)

  Info IP dhcp (option 82) option

  interface IG4

  activate a dhcp IP Relay

  The rest of your config seems fine for the switch.

  -Tom
  Please mark replied messages useful

• Configuration wireless router 891w

  Hi, looking for a wireless setup procedure part of 891w router - tried to follow the installation wizard and is stuck in access to interface BVI. The web page is open by clicking on the link in the present installation wizard only the button 'Enter' and it is.

  Could someone provide me with links to config info so that I can configure wifi using the good old CLI.

  Thanks in advance.

  I upgraded the IOS AP to ap801-k9w7 - tar.124 - 21A .JY, that solved the problem.

  Thanks again!

• Roaming between two autonomous Aps in root mode

  HI guys,.

  (Q) what is the difference between roaming and mobility between two autonomous APs?

  I configured two APs of stand-alone mode in root mode with the same settings (same wlan ID for two VLANs) wlan. How does choose between these two APs clients to connect.

  I read a few docs and they said they will choose AP on the intensity of the signal. My question is, do I need to activate some kind of roaming/mobility between them so that if clients connected to an access point moving to the AP another area, they will automatically connect to AP with AP signal stronger.

  Or how the roaming/mobility between two autonomous APs

  Thank you

  HI Safarazaz,

  Info: About the connection to the access point, the customer makes the final decision based on the use, the power of the signal... etc.

  So now we come to the point on homelessness:

  IF you use a WPA/WPA2-PSK, then all you need to do is configure the AP exactly the same way, with the exception of the IP address on the interface BVI.

  IF you use 802. 1 x, then you want to configure WDS to the cached key.

  http://www.Cisco.com/c/en/us/support/docs/wireless-mobility/wireless-LAN...

  Concerning

  Remember messages useful rates

• Cisco aironet 1130g

  Hello

  I tried to assign the ip address to my access point in light mode by using the command

  AP (config) # interface bvi 1

  but it doent keep giving error "an invalid entry detected""marker.

  Help, please... Thank you

  You cannot use the lightweight access points :-)

  I suggest you reconfigure them as IOS autonomous access points.

  Download the IOS software for this model AP and install it on the AP, then it will be configurable as a normal IOS device.

  The command is "archive download-sw/f/o tftp: / // '.

  If it does not allow you to type this command try to type "debug lwapp console cli" or "debug capwap console cli" everything first, but you need to be connected via the console (no telnet).

  Hope this helps!

  Nicolas

  ===

  Remember responses of the rate that you find useful

• Installation of two cisco 1142n roaming

  Hello.

  I bought the second 1142n access point to my home network and you're wondering how to implement roaming. I did a lot of reading for the last 2 days, but I need to clarify the following points.

  Should I use WDS?

  I like to keep the simple configuration with WPA pre-shared key, rather than using user and password to authenticate each user.

  It seems that this guy said that WDS is not really necessary for this installation. Should I configure WDS or do I simply configure same SSID with same WPA preshared key on access points and it will work fine?

  I tried to install WDS but.

  I tried to configure WDS with this article, but I do not understand some things:

  1. What do I need to configure the SSID on the two access points to make it work? I thought that the configuration will automatically replicate to the WDS client after WDS is running, but it wasn't the case. I created "wds" SSID on the two access points. Is this correct?
  2. While WDS seems to work, I am not able to connect to the SSID "wds". After you enter the user name and password, it does not connect. Seems the credentials do not work, or maybe something else. Pointers?
  3. I have configured users under the Local Radius Server-> individual users. Is this correct?
  4. How you would install two access points of 1142n for use domestic?

  Here is my config

  ------------------ show running-config ------------------
  
  Building configuration...
  
  Current configuration : 3937 bytes!! Last configuration change at 19:28:35 DST Sat Jan 16 2016! NVRAM config last updated at 19:28:35 DST Sat Jan 16 2016! NVRAM config last updated at 19:28:35 DST Sat Jan 16 2016version 15.3no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname alsap02!!logging rate-limit console 9enable secret 5 !aaa new-model!!aaa group server radius rad_eap!aaa group server radius rad_mac!aaa group server radius rad_acct!aaa group server radius rad_admin!aaa group server tacacs+ tac_admin!aaa group server radius rad_pmip!aaa group server radius dummy!aaa group server radius infrastructure!aaa group server radius clients!aaa authentication login eap_methods group rad_eapaaa authentication login mac_methods localaaa authentication login method_infrastructure group infrastructureaaa authentication login method_clients group clientsaaa authorization exec default localaaa accounting network acct_methods start-stop group rad_acct!!!!!aaa session-id commonclock timezone EST 10 0clock summer-time DST recurring 1 Sun Oct 2:00 1 Sun Apr 3:00no ip source-routeno ip cefip domain name allsupp.corpip name-server 192.168.30.10!!!!dot11 syslog!dot11 ssid  authentication open authentication key-management wpa version 2!dot11 ssid connect authentication open authentication key-management wpa version 2 guest-mode wpa-psk ascii 7 14141D050201293F292D!dot11 ssid wds authentication open eap eap_methods authentication network-eap eap_methods authentication key-management wpa version 2 no ids mfp client!!!no ipv6 cef!!username admin privilege 15 secret 5 !!ip ssh version 2bridge irb!!!interface Dot11Radio0 no ip address ! encryption mode ciphers aes-ccm ! ssid connect ! ssid wds ! antenna gain 0 channel 2417 station-role root no dot11 extension aironet bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding!interface Dot11Radio1 no ip address ! encryption mode ciphers aes-ccm ! ssid connect ! ssid wds ! antenna gain 0 peakdetect no dfs band block channel width 40-above channel dfs station-role root no dot11 extension aironet bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding!interface GigabitEthernet0 no ip address duplex auto speed auto no keepalive bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning!interface BVI1 mac-address d48c.b54e.c222 ip address 192.168.30.252 255.255.255.0!ip default-gateway 192.168.30.254ip forward-protocol ndip http serverno ip http secure-serverip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eagip radius source-interface BVI1!!radius-server local no authentication eapfast no authentication mac nas 192.168.30.252 key 7 020316495F144E user wds nthash 7 115F3A514641535B257C7D717B606D7A4B26425024000E79760557564C437F0E76 user test nthash 7 025627795D5F5B79141E5C3F524E45292A560B73767063627B4454345B58030A0F!radius-server attribute 32 include-in-access-req format %h!radius server wds-radius address ipv4 192.168.30.252 auth-port 1812 acct-port 1813 key 7 !bridge 1 route ip!!wlccp ap username wds password 7 09495C1B4D1756wlccp authentication-server infrastructure method_infrastructurewlccp authentication-server client eap method_clients ssid wdswlccp wds priority 255 interface BVI1!line con 0 exec-timeout 5 0 logging synchronousline vty 0 4 exec-timeout 60 0 length 0 transport input all!sntp server 192.168.30.10sntp broadcast clientend

  alsap02#sh wlccp wds MAC: d48c.b54e.c222, IP-ADDR: 192.168.30.252 , IPV6-ADDR: :: , Priority: 255 Interface BVI1, State: Administratively StandAlone - ACTIVE AP Count: 2 , MN Count: 4
  
  alsap02#sh wlccp ap WDS = d48c.b54e.c222, IP: 192.168.30.252 , IPV6: :: state = wlccp_ap_st_registered IN Authenticator = IP: 192.168.30.252 IPV6: :: MN Authenticator = IP: 192.168.30.252 IPv6:
  
  alsap03#sh wlccp ap WDS = d48c.b54e.c222, IP: 192.168.30.252 , IPV6: :: state = wlccp_ap_st_registered IN Authenticator = IP: 192.168.30.252 IPV6: :: MN Authenticator = IP: 192.168.30.252 IPv6:
  
  

  Thank you for your help. Jiri

  Hello

  If you use a WPA2/PSK, then all you have to do is configure the AP exactly in the same way, with the exception of the IP address of the interface BVI.

  So as long as the SSID and encryption are the same, and there is overlap between the cells the customer should wander between the AP.

  Info: only if you use 802. 1 x, then you want to configure WDS to the cached key.

  Concerning

  Remember messages useful rates

• How do I see the IP Source address of a customer using ACE One-armed-mode of loading balance HTTP proxy request

  I use a device of 4710 Ace deployed in armed mode, use Source TAR to balancing HTTP request to a couple of Proxy servers.

  Everything works well, but the thing is that I do not see the client IP addresses on the Proxy logs, so I can't keep track of them.

  Interfaces and the Nat configs are:

  interface vlan 200

  Description of server-side-VLAN

  Bridge-Group 5

  NAT-pool 5 10.1.1.5 10.1.1.5 netmask 255.255.255.0 pat

  entered service VIP policy

  interface vlan 300

  Client-Side-VLAN description

  Bridge-Group 5

  interface bvi 5

  IP 10.1.1.3 255.255.248.0

  Interface Client-Server virtual description

  IP route 0.0.0.0 0.0.0.0 10.1.1.1

  and the policy looks like this

  Policy-map multi-game VIP

  class port 80

  Balancing vip continues

  policy of balancing port 80

  NAT Dynamics 5 vlan 200

  The resource assignment:

  Sticky ip-netmask 255.255.255.255 address two CLASSES of RESOURCES

  Timeout 5

  Serverfarm Service80

  Any suggestions will be appreciated,

  Thank you

  Hello

  You can use X-forwarded-for to insert the IP address of the client in the header Http. take a look at the link below:

  http://www.Cisco.com/en/us/products/HW/modules/ps2706/products_configura...

  Let me know if you have any questions.

  Kind regards
  Kanwal

  Sent by Cisco Support technique iPhone App

• AIR TOUR 1142N

  Hello

  I have an AIR TOUR 1142N, I want to make this AP as standalone, but I am not able to configure terminal command and I don't get too interface BVI

  show ip int in brief

  I send you my running configuration Access Point

  APa493.4c52.a91f #sh run
  Building configuration...

  Current configuration: 16735 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname APa493.4c52.a91f
  !
  enable secret 5 $1$XhAv$99uKdgB4Jo.dhS1TKchY//
  !
  !
  Crypto pki trustpoint Cisco_IOS_MIC_cert
  revocation checking no
  rsakeypair Cisco_IOS_MIC_Keys
  !
  Crypto pki trustpoint cisco-root-cert
  revocation checking no
  rsakeypair Cisco_IOS_MIC_Keys
  !
  Crypto pki trustpoint airespace-device-root-cert
  revocation checking no
  rsakeypair Cisco_IOS_MIC_Keys
  !
  Crypto pki trustpoint airespace-new-root-cert
  revocation checking no
  rsakeypair Cisco_IOS_MIC_Keys
  !
  Crypto pki trustpoint airespace-old-root-cert
  revocation checking no
  rsakeypair Cisco_IOS_MIC_Keys
  !
  !
  string Cisco_IOS_MIC_cert crypto pki certificates
  certificate 2333A54B000000080D96
  30820470 30820358 A0030201 02020 HAS 23 33A54B00 0000080D 96300-06-092A 8648
  86F70D01 01050500 30393116 30140603 55040A 13 0D 436973 636F2053 79737465
  301 0603 55040313 16436973 636F204D 616E7566 61637475 6D73311F 72696E67
  1E170D31 20434130 32303531 34323034 3035325A 170 3232 30353134 32303530
  35325A 30 818C310B A 30090603 55040613 02555331 13301106 03550408 130, 4361
  6C69666F 726E6961 06035504 07130853 616E204A 6F736531 16301406 3111300F
  0355040A 130D 4369 53797374 656 7331 1B, 301906 03550403 13124331 D 73636F20
  61343933 34633532 61393166 3134302D 3120301E 06092A 86 4886F70D 01090116
  706F7274 11737570 636F2E63 40636973 6F6D3082 0122300D 06092 HAS 86 4886F70D

  !

  username Cisco secret 5 $1$ Jug8$ lzs5T1AoQfo8e3tXN05uy.
  !
  !
  !
  interface GigabitEthernet0
  customer_id GigabitEthernet0 dhcp IP address
  no ip route cache
  automatic duplex
  automatic speed
  No keepalive
  !
  !
  Line con 0
  line vty 0 4
  opening of session
  !
  end

  APa493.4c52.a91f #.

  APa493.4c52.a91f #sh ip int bri

  Interface IP-Address OK? Method State Protocol

  GigabitEthernet0 unassigned YES other upward to the bottom

  APa493.4c52.a91f #.

  * 00:20:44.944 Mar 1: % CAPWAP-3-Journal of ERRORS: do not send discovery request AP doesn't have an Ip address.

  And I get this error message

  CAPWAP-3-ERROR log %: do not send discovery request AP doesn't have an Ip address.

  Shoud I have to reset the access completely, need help point.

  You can enter in the mode of a TOWER configuration using command "debug console cli capwap' as shown below

  3600-1 #debug console cli capwap

  This command is intended only for debugging/troubleshooting

  Any changes to the configuration may cause different

  behavior of centralized configuration.

  CAPWAP console CLI allow/disallow the debug is on

  3600-1 #conf t

  Enter configuration commands, one per line.  End with CNTL/Z.

  3600-1 (config) #.

  Below should help you to go AROUND to the conversion of the IOS

  http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

  HTH

  Rasika

  Pls note all useful responses *.

• Cisco 2821 doesn´t accept virtual-ppp1

  Hello

  I have a cisco router with IOS c2800nm-ipvoice_ivs - mz.124 - 24.T3.bin 2821.

  The question is that I m trying to configure an L2TP tunnel but the router Don t accept that I have configure the virtual-PPP1 interface:

  «

  (config) #interface?
  Async Async interface
  Interface auto-model
  BRI ISDN basic rate interface
  BVI bridge-group virtual interface
  CDMA-CDMA Ix Ix interface
  CTunnel CTunnel interface
  Cellular cellular WAN interface
  Dialer Dialer interface
  GigabitEthernet GigabitEthernet IEEE 802.3z
  Group-Async Async interface group
  Interface Lex Lex
  Loopback-Loopback interface
  Multilink bundle LIM frame relay interface
  Multilink-group interface MultiLink Panel
  Null null interface
  Channel port Ethernet Channel of interfaces
  Virtual interface SSLVPN SSLVPN-high HEAT
  Series series
  Tunnel tunnel interface
  Bright multicast PGM host interface
  Virtual-PPP PPP virtual interface
  Virtual virtual-template interface
  Token Ring virtual Virtual Token-Ring
  range range interface command
  VMI Virtual Interface Multipoint

  (config) #interface vitual-PPP1
  ^
  Invalid entry % detected at ' ^' marker.

  »

  The pseudoeire is not yet recognized:

  «

  (config) #pse?
  % Unrecognized command

  »

  I have already set up:

  «

  VPDN enable

  IP cef

  L2TP L2TP-class
  authentication

  »

  In the cisco site this IOS supports L2TP. The router accepts the command show l2tp

  Best regards

  Nelson Mendes

  Hello

  I would recommend c2800nm-adventerprisek9_ivs - mz.124 - 24.T3. It is a superset of the set of features - ipvoice_ivs - you have now, so you should not lose features of IOS, see:

  http://www.Cisco.com/en/us/partner/prod/collateral/routers/ps5854/prod_bulletin0900aecd802a9493.html

  Thank you

  Wen

• Cisco ASA 55XX Transparent mode through a VLAN

  Hello team Cisco Forum!

  In a scenario where the Cisco ASA is in Transparent mode, it is possible to route the traffic of L2 other VLAN different that the VLAN native IP for the firewall management lies?

  Switches on the outside and the inside of the interfaces of the SAA are in trunk mode, and I'm moving ttraffic VLAN L2 from inside to outside and vice versa by using filters on switches (switchport trunk allowed vlan).

  Thank you in advanced for your support and comments!

  Yes it is possible, but you will be limited to 8 VLAN, or more precisely, 8 interfaces BVI so it's not a scalable solution.  The problem is that you will need to have different VLANS to the same subnet at both ends of the SAA.

  To clarify this point, lets say, you use the interface Gig0/1 and Gig0/2.  Gig0/1, you would set up subinterfaces with VLAN 2, 3 and 4.  Now, if you try to configure the same VLAN on Gig0/2, you will get an error saying something like this VLAN is already configured on another interface. I don't remember the exact error.

  So to get this working, you need to configure Gig0/2 with subinterfaces for VLAN... lets say... 5, 6 and 7.  you would then associate VLAN 2 and 5 with BVI 1, VLAN 3 and 6 with 2 Virgin Islands British and VLAN 4 and 7 with 3 British Virgin Islands.  Each interface BVI would have its own IP address for the subnet on which is to be filled in all of the ASA.

  --

  Please do not forget to select a correct answer and rate useful posts

• BVI Interface inaccessible since the addition of multiple SSID

  Announcement to the community for the first time.

  I have a simple HomeLAN which consists of a Cisco router for series 800-> switch PoE Cisco3560-> Cisco Aironet 1131AG Access Point.

  Everything works well for a while in which I had a simple port to "change the access mode" configured on the switch facing the AP and one SSID on the access point that is configured in stand-alone mode (without controller).

  My provider has enabled IPv6 on my broadband connection and I started to reconfigure my installation this afternoon to allow this.

  I decided to run only a bunk Dual LAN and a separate native IPv6 only test LAN for proof of concept.

  With this in mind, I changed the switch port to the access point to a "mode trunk switch' using simple dot1q encapsulation. I have also consulted the post helps very https://rscciew.wordpress.com/2014/05/24/multiple-ssid-configurations-on... after finding in this community post on the topic of multiple SSID https://supportforums.cisco.com/discussion/10899511/how-broadcast-2-ssid...

  I have now two SSID broadcasting (we will call double stack and ipv6 only for the sake of the argument). The SSID double stack uses VLAN 2 and 1 bridge, while the SSID only ipv6 uses 6 VLAN and bridge 6.

  I must stress at this point that my router (where I want to layer 3 for the two LANs gateways) I have DHCP, DHCPv6 and SLAAC configured on relevant VLANs.

  I seem to be the 2 VLAN trunking of properly and I can see the SSID broadcast in my house. I can connect to the SSID (authenticate and form an association as seen in 'show the dot11 association'), but I don't get an IPv4 address or IPv6 assigned to all clients (I tried Mac OS x, iOS, Android, and Windows phone). Furthermore, I can't ping the IP bvi1 of the AP - that is the element that is annoying me more that I must console to the AP to make any changes at all.

  Here is an overview of my AP configuration, with relevant parts removed for safety...

  dot11 syslog
  !
  dot11 said ipv6 only
  VLAN 6
  open authentication
  shared authentication
  authentication wpa key management
  MBSSID-guest mode
  WPA - psk ascii 7
  !
  dot11 said double stack
  VLAN 2
  open authentication
  shared authentication
  authentication wpa key management
  MBSSID-guest mode
  WPA - psk ascii 7

  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  the cipher mode vlan 6 encryption tkip aes - ccm
  !
  the ciphers of vlan 2 encryption tkip aes - ccm mode
  !
  has declared ipv6 only
  !
  such double stack
  !
  MBSSID
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface Dot11Radio0.2
  encapsulation dot1Q 2
  no ip route cache
  Bridge-Group 2
  the bridge-group subscriber-loop-control 2
  Bridge-Group 2 block-unknown-source
  No source of bridge-Group 2-learning
  No extinction unicast by bridge-Group 2
  Bridge-Group 2 covering-disabled people
  !
  interface Dot11Radio0.6
  encapsulation dot1Q 6
  no ip route cache
  Bridge-Group 6
  the bridge-group subscriber-loop-control 6
  Bridge-Group 6 block-unknown-source
  No source of bridge-Group 6-learning
  No bridge Group 6 unicast-flooding
  Bridge-Group 6 covering-disabled people
  !

  interface FastEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0.2
  encapsulation dot1Q 2
  no ip route cache
  Bridge-Group 2
  No source of bridge-Group 2-learning
  Bridge-Group 2 covering-disabled people
  !
  interface FastEthernet0.6
  encapsulation dot1Q 6
  no ip route cache
  Bridge-Group 6
  No source of bridge-Group 6-learning
  Bridge-Group 6 covering-disabled people

  Bridge IRB

  1 channel ip bridge

  interface control2
  MGMT AP Interface Description
  address 192.168.1.6 IP 255.255.255.0
  no ip route cache

  IP default-gateway 192.168.1.50

  As you can see I can not ping the gateway of AP - I would be very grateful if someone could point me in the right direction with regard to what I'm doing wrong here?

  Thank you

  Mick

  OK means your AP is to have IP vlan2:

  Do it like this and try again:

  !

  interface Dot11Radio0.2
  encapsulation dot1Q 2
  encapsulation dot1Q 2 native
  Group 1 bridge
  Bridge-Group 2
  !
  interface FastEthernet0.2
  encapsulation dot1Q 2
  Group 1 bridge
  encapsulation dot1Q 2 native
  Bridge-Group 2

  !

  Or alternatively, you can delete the name native dot11radio0 and fa0.2. (It should also work without it), but be sure that for vlan 2 you have bridge Group 1.

  Concerning

  Remember messages useful rates

• How can I put wireless and ethernet interfaces together?

  I have a 877w router, and I'm trying to set up a wireless network.

  I have a bridged RFC1483 ADSL, so I ATM0.1 in a group of bridge, and then, I defined an interface BVI1.

  However, after you have configured the wireless interface, I noticed that my laptop is the IP address of the supplier, as if wireless had precedence on the BVI interface. Put the Dot11 interface in a separate bridge under VLAN1 does not seem to help either. I tried to put everything in the same bridge, but fast ethernet interfaces do not support address (how the British Virgin Islands work then, I wonder).

  What should I do? Use two VLANS separated? I wouldn't do that. Any help appreciated. Thank you

  Hey, thank you, that did it.

  So I followed the article. I guess I don't understand how the British Virgin Islands. Of the article, I thought them then were at the same level, i.e. all the right behind the ATM interface. I also thought that a BVI able to fill several VLANS. Now my next mission is to understand why I was wrong on both counts.

  Guys, thank you very much for the help. Now I'll try to better understand what I :-)