AIR TOUR 1142N

Similar Questions

• Not able to connect the AIR-tour 1041N-A-K9 using windows 8

  Hello

  I use AIR-TOUR 1041N-A-K9 wireless Accesspoint it was controlled using the command Air-CT2504-k9 wireless.

  When I tried to connect to the access point using the Windows 8 machine was not able to connect,

  Is there someone who faced the same problem.

  Hello

  There is a known bug with Windows 8 connectivitiy problems with Cisco UWN.

  https://supportforums.Cisco.com/docs/doc-27213

  Can you please try the solution proposed in the document and see if it works?

  HTH,

  Patrick

• Downgrade from AIR - LAP 1142N autonomous

  Hell, can someone tell me where I can download IOS for Air-AP1142N-E-K9

  On the official website, I can't because I don't have access.

  I installed tftpd, netstat | grep 10.0.0.1 say this download AP image, but what connections ends red flashing, ap. I think thet what IOS is corrupt.

  I tried to find by google, but all that is similar.

  Thanks, sorry for my English.

  Hello Eric,

  Unfortunately, there is no other repository outside Cisco.com we recommend allows you to download the image to the 1142 standalone.

  After buying the 1142 regularly, you should be able to create an account on Cisco.com and access the download section: let us know if you have problems with this.

  About how to convert the light AP autonomous, you can also consider the following option:

  1. download the standalone IOS image to a TFTP server (tftpd32 is a well recommended for this software).

  2. Telnet to the 1142 and go to activate the mode (default user and password should be Cisco/Cisco, if it has not been changed).

  3. from the CLI, type the following command

  debugging console cli capwap

  Archive Download-sw / overwrite/reload tftp: / /.

  Kind regards

  Fede

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Version of the AIR-LAP1141N IOS upgrade

  How can I upgrade the IOS Version of AIR - TOUR of 12.4 (21 a) JA to JB 15.2 (2) try joined to my vWLC Release 7.4.100

  This ROUND-AIR was joinned on any controller, and I have access to the CLI Console.

  I try to type orders archive and upgrade, but are marked as "unrecognized % orders."

  After a question mark '? ' I see 'upgrade' command, but is always marked as "unrecognized % of orders.

  

  I have the TFTP server with my ios image.

  Somene can help me on?, what I need to do to upgrade this AP.?

  Thanks in advance for your help.

  issue the following:

  Debug lwapp console cli

  Make sure that you type all as the '?' Will not display the command

  Now, you will be able to make the order of the archive. The other way is to do the following:

  By using a TFTP server to revert to a previous version

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/u...

  https://supportforums.Cisco.com/docs/doc-18268

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/u...

  http://www.YouTube.com/watch?v=QQ_NuxdRhQ4

  https://supportforums.Cisco.com/docs/doc-14960

  Sent by Cisco Support technique iPhone App

• management of WCS, WLC and H-REAP AP1242

  We have chosen to deploy 1 wlc2106(k9-7-0-98-0) and 4 or 5 APs 1242, LAP - AIR and AIR - AP converted to AIR TOURS in each office, with a backup 1 WLC5500, in seat.

  We have WCS (v7.0) and in this architecture, 1242 APs will be always connected on 1 of 2 WLC (never in autonomous REAP).

  In normal mode, WLAN, working in the central authentication and Central switch. In backup mode, WLAN work in central authentication (backup WLC headquarters) and local switching.

  For the configuration of the WLC, is it really necessary to create and REAP H unit for all the Aps or can I leave by default-AP group?

  I have a problem with AIR - AP converted it TURN: I can't push a TOUR from the WCS model:

  AP0022.90.1b.9d36 is the converter of AIR - AP.

  another AP are AIR - LAP: Ok for this model that apply

  

  What can be the problem with this access point?

  Thanks for your help.

  Lorenzo

  The best for homelessness must have WLC, authentication management. Now, if there is a WAN link rather slow in the game, perhaps, he retorted the initial advantage of it.

  In this case REAP H groups will allow roaming between aps hreap seemless.

  In any case, it does not hurt to combine your APs in Hreap groups. It can only help. So ... :-)

  Nicolas

  ===

  Remember responses of the rate that you find useful

• 550-110: orientation tour

  OK to ask the Tower on the side for optical drive opens horizontally to the top? I know that in the old days, when engines used hard drives, orientation tour was critical. In my view, modern readers can operate in any position but would feel better advice of experts. Thank you.

  Artbuc195252 wrote:
  

  Thank you. I did set up for my SIL and this is where the unit is now. IIRC, if I put the right down side (just as you are looking at the front), the optical drive will open downwards. I he will throw on the left side and create a space for air circulation as you suggest even if I do not remember seeing air vents on the side. In any case, essentially it's the internal material is not compromised, right?

  Yes. That's the main point.

  I suggested the right because it is usually the side mounted on the motherboard. The internal hardware will not be compromised.

  Everything is tywrapped or otherwise fixed by screws or clips.

• Area of regulation 1142N

  Hello

  Can someone confirm please what model 1142N APs I need to buy to work in Australia with 4404 WLCs please? From what I can tell I need the model AIR-LAP1142N -N- K9, is that correct? We are still running a pre-CAPWAP on the WLCs v4.2.x.x software by the way.

  Thank you.

  Brodie

  Hi Brodie,

  N - is more correct my friend

  Compliance status of LAN wireless

  http://www.Cisco.com/en/us/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps6087_Products_Data_Sheet.html

  See you soon!
  Rob

  Thank you to support CSC helps Haiti

  https://supportforums.Cisco.com/docs/doc-8895

  https://supportforums.Cisco.com/docs/doc-8727

• Warning of low power for AIR-LAP1242AG-C-K9

  Hey Buddie,

  We bought a few AIR-LAP1242AG-C-K9, but not perchasing no matter what wireless controller. When I connect the TOWER to the port of Cat2950 or Cat2960 TRP, all the TOUR cannot start normally. It shows low power, please consult the attached two images. But if I use the external power cable, the TOUR can work well. So, I would like to know two things.

  1. can I use stand-alone TOWER without using the controller?

  2. If the above is Yes, how can I configure the PPoE on cat2950 to TURN Support correctly?

  Thank you very much.

  Hi Jian,

  Q. can you a RIDE operate independently of a wireless LAN (WLC) controller?

  A. No, towers may operate independently of the function WLCs. tours in conjunction with a WLC only. The reason is that the WLC provides all the configuration settings and the firmware that the TOUR needs in the process registration.

  So you will need to return the AP and download the version of IOS, buy a WLC or convert the TOWER to IOS :(

  Q. how to distinguish between a regular (standalone) AP and a TOWER?

  A. the best way to distinguish between a regular access point and a TOWER is to look at the reference number of the AP.

  LAP (AP light Protocol [LWAPP])? The numbers always begin with AIR-LAPXXXX.

  Autonomous AP (Cisco IOS? Software)? The numbers always begin with AIR-APXXXX.

  This doc. good Q and A

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/products_qanda_item09186a00806a4da3.shtml

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  I hope this helps!

  Rob

• AIR-LAP1131AG-E-K9

  Hello Experts,

  We are in the process of purchase of 5 1131AG Cisco AIR-LAP1131AG-E-K9. However I have some doubts to clear

  a. first of all, we don't have WLC

  b.Will AP have IOS? What version it will be.

  can c. I convert their AIR-AP1131AG?

  d. or keep them as TOUR

  Please can someone help pe clrarify these doubts.

  Thank you

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Hello

  Please use the below doc and this will solve the problem we are facing...

  https://supportforums.Cisco.com/docs/doc-14960

  Let me know if this answers your question!

  Concerning

  Surendra

• Is AIR 3.3 compaible with Windows 7 x 64?

  I downloaded 3.3 AIR and installed. on the download site, it says that there is a version for windows 7 x 32. I have extensions in dreamweaver is not working and the AIR is the cause suspected according to the Director. I have windows 7 x 64 and using CS5.5. I can't the sample out of the Adobe Web site extensions to work either. Adobe technical support refuses it might be a problem with their software. I also tried to run in compatibility and tested mode extensions, but cannot complete the install without a properly functioning AIR. Extensions are Zpose and TourDeFlex photo gallery. Anyone else having the same problems?

  Thank you, while this is not the journal of AIR, it seems you have a problem during the installation MSI part.  Googling the error 'Error 1606. Could not access network (calculated) location. "leads me to believe that Setup is having a problem to either solve or to access any path, I'm not sure where"calculated"carries out.

  Try creating a new windows, temporary (level admin) user account and reinstall AIR.  Do you get any error messages?  If this is not the case, try reinstalling Tour de Flex, it does not install?

• 3 captive DURATION of AIR environment

  Since AIR 3 has a captive runtime environment and allows users without administrative privileges system/install, will this reported in RH AIRHelp? If so, when? Thank you!

  No, it's the right place Rick ;>)

  @Maggie - know anyone on these forums - it's all user tour here. If you want to vote for it, go to this site: https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform&product=38 and let Adobe know.

• Tour of Flex Tester sample?

  Well, I guess I play stump-the-saddle with the Tour de Flex AIR sample tester. I followed Greg's old instructions on how to

  use it. I see that the tester of the sample, but I don't see where I can place my URL to test a sample application.

  Can someone tell me please how to test using the latest version?

  The tester of the sample is broken.  We have to fix it in the next few weeks (just after Adobe MAX).

  If you want to see what your sample, you can always hand edit the XML file.  Find the file objects - desktop2.xml.  This is a catalog of samples.  You can put your own URL in this file and test.

  NOTE: the file desktop2.xml - objects is replaced a lot of time, we publish a new sample, so your changes will be overwritten at any time.

  If accidentally you break the file, simply delete and re - run Tour de Flex.

  We will soon have a new sample tester.  If you have samples to contribute, please contact me at gwilson (at) adobe com

  Thank you!

  Greg

• Broken space on MacBook Air

  I have a MacBook Air, I tried to clean below the space bar. I think I broke it because when I put back it together it is incredibly hard to push and I need to move so he could push. How can I fix? I just need to get a new keyboard?

  Make an appointment at the Genius Bar in Apple for the service. If you need a Apple Store - find a store - Apple.

• 2 Air 10 iOS iPad dropping wifi

  I have an iPad 2 air in perfect condition, since it first came out. I have the cell phone/Wifi version with Verizon. My problem has been lately, when connected to wifi, the wifi shuts on the iPad many times when using, and more so at rest.

  Did somebody encounter this problem since upgrading to iOS 10 It is the only variable that has changed, I'm still using the same networks that I have always used for Wifi.

  Follow these steps to find and correct the problem:

  1. you must check your Wi - Fi router: check if other devices can be connected. This will let you know if there is a problem with your Wi - Fi router. You can restart your router and restart the connection to WiFi.

  2. make sure that Wi - Fi on and you can see your network

  3. go to settings on your iPhone > Wi - Fi and check if it is enabled. And if there is a blue check mark next to a network name means that your iPhone or iPad was connected to this network.

  4 restart your iPhone/iPad, router, cable/DSL mode

  5. If this does not help, reset your network. On your iPhone, iPad, got to settings > general > reset > reset network settings. This will reset Wi - Fi networks and passwords, cell parameters and VPN, and APN settings you used before.

  These measures should help.

• Cannot start new iMovie on iPad Air project

  Hi, I need to do a project for my university studies, final evaluation. I'm hoping to use iMovie on my iPad Air, as I have done so successfully in the past.

  This week, I'm in iMovie and click the symbol +. Then I click on the option to create a new project or a trailer. But when I click on one of these options, nothing happens. If I click Cancel, nothing happens and the application crashes. I have to then close and reopen the app.

  Look at a last projects is not a problem.

  Indices received with gratitude. I wonder if it's because I recently upgraded to iOs.

  iMovie has been updated for iOS 10. Make sure you have the latest version installed.